Related
HI
i am new to this plaise help
i got SPV M1000 witch i install TOMTOM 4.00
the problem is when i click on tomtom navigator
i get this massage: gps position unreliable
plaise tell me STEP BY STEP how do ACTIVATE GPRS
coz i am new to this
tnx
Nice and easy....
Launch TT, goto config, goto GPS
If you have a little circle at the top right spinning then it's connected to your GPS device, however if you get a popup asking you to pair it, then do the following
Search in BT, you should find the GPS device, pair to it (dont use a code if asked)
Tick the allways connect to this device tick box, ok all the way out and TT should now be talking to the device
It will take a while to initially pick up satelites, you should see some grey bars and numbers in the GPS window inside TT.... Also make sure your outside
Hi King2,
are you getting GPS and GPRS confused?
you don't mention a GPS unit in your post (but you do mention GPRS)-- do you have one? TT is useless without.
the GPS unit (usually cabled/bluetooth) is basically a satellite receiver which TT uses to locate your position.
Hi,
GPS Position Unreliable means that the GPS Module not found any satelites.
When you don't have the module you don't get this message.
Then TomTom says GPS module not found.
I takes about a minute or so to conect to a satelite.
But you must be in a open space otherwise the module can't connect.
When you are between buildings the connection is difficult.
Hope this helps
Greetings [email protected]
COM PORT HELP????
HI
TNX FOR HELP
i upgrade my SPV M1000 from win 2003 to 2003SE and the
GPS TO V 3.07 the problem i got is:
on the bluetouth settings,bluetouth serial port setup:
INBOUND COM PORT:COM4
OUTBOUND COM PORT:COM5
now on the GPS TAB
on the top drop i got TOMTOM NAVIGATOR GPS
and on the second drop i got COM 5
now I CANT TICK THE BLUE CHECKMARK BOX TO START THE CONNECTION but before i upgrade to win 2003SE it was OK
any help plaise and tnx
----------------------------
ROM version:2.06.00WWE
RADIO version:1.18.00
EXTROM versionIAMOND 1.2se
Port Problem
Hi King2,
Did you paired the phone and the BT GPS?
It is where you put the BT on
Settings / Connections / Bluetooth / Devices / New
If you did there was a question about a bluetooth serial port connection.
You must answer yes or no. Use yes
If you tick yes, WM2003SE creates a BT Serial port.
I think in the text it also says what port was created. (i saw in a flash that is was BT Serial Port 5
In TomTom got to GPS and take BT Serial on Com 5
Uncheck the port 4.
I din't change the settings and when i just looked in the BT Settings only the Outbound Com port: 5 is checked and 4 is not
I hope this helps
Greetings [email protected]
COM PORT HELP???
HI
TNX FOR HELP
NO I CANT paired the phone and the bt gps: DEVICE NOT FOUND
I DONT get any question about a bluetouth port connection
but in TOMTOM GPS I DO TICK THE COM 5 in second drop
the problem is i CANT TICK THE BLUE CHECKMARK BOX TO START
THE CONNECTION
is ok with COM 4 but no COM5
COZ IF I CANT TICK THE BLUE BOX TO START THE CONNECTION
I CANT PAIRED?
any chance to change the COM PORT settings in BLUETOUTH SETTINGS?
tnx again for your help
Hi King2,
You must pair your BT GPS otherwise it won't work.
What for BT GPS do you have :?:
And did you put the GP on when you try to pair. (it a silly question but i have to ask you).
Did you BT GPS came with extra software :?:
Were going to get it to work :wink:
TOMTOM GPS
HI [email protected]
tnx for your help
IT S ALL WORKING NOW
i did paired them and it s working like dream
your r top man
hi all
i have had a right time trying in vain to get my t mobile MDA compact to work with the holox BT-321 GPS receiver. the reason i am having so much trouble is when i pair the devices, a small window flashes up and says "This bluetooth device supports serial port profile, would you like to create a bluetooth serial port for it?" the window box is labelled "bluetooth serial port COM5" of course i click yes, it asks me for the name, and i leave it what its called "BTGPS74R" and click finish, this leaves me on the main menu. in the com ports tab there is "new outgoing port" and "new incoming port" i click outgoing and next and low and behold there is nothing in the box whatsoever to select. i have checked all the boxes in my bluetooth settings for the 2 com ports.
the phone refuses to show any ports at all, i have flashed the imate jam rom 1.12 as i read that solved it, but it never, i have tried a bluetooth program called pocket bluetooth tools and this brings with it more com ports but they do not actually work by putting the ports in the drop down list, its still empty !!! also when i select say port 6/7/8 the small window flashes up saying "this device supports......" and then the pocket tools dissappears and its all back to nothing again.
i am at my wits end with it and i dont have a clue how to get this bluetooth port to actually show up so i can bond with my bluetooth GPS and make tom tom 5 work
thank you anyone who can help me
Dan
Hi,
i just resolved exactly the same problem on my mda compact.
I had to do a complete reset of the device...
Hi
I am having a similar problem. I have an orange SPV M1000 and the same bluetooth GPS device. It is paired in bluetooth devices. When I got to connect on Tom Tom 5 it can't pich up the receiver. I have tried all the different wired/bluetooth etc device settings in TT as it says to try wired if bluetooth doesnt work. But to no avail. I'm tempted to try different sat nav software. Any ideas? Let me know if your issue gets resolved!
cheers
AJ
Hi guys,
The options for new outgoing/incoming port creation are to connect to a device with which you haven't paired. My gps creates a com5 too, like all of yours & TT5 finds it pretty fast when I have it to use 'another bt gps' @ com5.
When you think a hard-reset will solve your problem, get yourself a good backup first. Cause sometimes you can restore that backup & the problem is still solved.
BTW does your gps support nmea protocol? TT can only handle nmea & that could be the cause when your gps is setup for external communication with another protocol.
Good luck M
Thanks for the reply
Hi there
I've attached the info from my receiver, looks like it should be ok.
Tom Tom only has connections on infrared, BT on COM6, Serial Cable on COM1, COM9:, COM2:, and Serial on USB
When I go to Start>Settings>Bluetooth settings there are options for bluetooth serial settings. These are non changable and if you check the boxes it will set Inbound Com port to COM4 and Outbound COM port to COM5.
These com ports dont seem to be options in Tom Tom 5 which confuses me.
So i download a program called BeeLineGPS which does a scan of all the ports and baud rates which I thought would be easier than the manual setup of TT5.
Try the com port options mentioned earlier with the BeeLine software and it still cant pick up the GPS device. Tried fiddling around for ages and still not working.
Do I need some kind of software for forwarding the ports so TT5 can see the device.
The advert for the device i bought promised me and easy set-up but this is being a pain
http://cgi.ebay.co.uk/32-Channel-Bl...03433467QQihZ018QQcategoryZ4668QQcmdZViewItem
All Fixed now. I upgraded the Rom to a newer version. After this the tom tom picked up that it was actually on port 5 which it wasnt doing before. Bobs your uncle
I am trying to set up tomtom 5.21 with my BTGPS74 receiver but cant get the two to communicate. I know there is some settings you can change in settings/system/gps but the problem I have is I dont have the gps option in settings anywhere. Am I missing something? Does any on know what I should do. Tomtom wants me to use port 3 or 7 but when I try to set them in bluetooth settings it says its not possible check your settings. Any suggestions would b welcome. Thanks.
P.S I know the receiver works as it still works well with my N70.
...you should've gotten a GPS icon if software GPS recognized.
In rgister you can force simulation.
hklm\controlpanel\gps]
delete redirect and add 'group' with dword=2
Then GPS icon will appear.
I gave it programport 7,hardware 6, baudrate=57600
gps auto checked
I'm not sure about the settings...
I had to create incomming and outgoing com ports on my 3100 (not sure if you need both)??
TomTom used com port 9 and works like a dream
as soon as you start the programme it connects automatically as long as my receiver is on.
It even connects when the BT on the 3100 is turned off - it starts the BT automaticlally when tomtom runs!
Yeah i agree all you need to do is set up the com ports, then fire up tomtom and select the com port you just set up and away it goes
Chris
Thanks for the replies guys. I know I have to set the com ports but the problem I have is there is nowhere for me to do this. For some reason the gps settings is missing from the system/settings. I am going to try to reinstall tomtom to see if it helps. Tomtom has ports 3 and 7 showing but they seem to be taken by something else so I cant configure my receiver on either of them.
I have a slightly different problem... my TyTn can connect to the BT GPS reciever, but as soon as TomTom tries to calculate a route, or I click the GPS signal icon it crashes back to the Today screen...
I've got TomTom installed with 5.21 update, anyone had any problems like this?
you just need to pair your bluetooth device go to settings connections and bluetooth and add new device, let your tytn search and it will find a new device when you have paired it select new comm port outgoing
I have no gps setting in control panel either
Cheers
Chris
Hi,
i have a strange problem with my BT. I cant create a incoming or outgoing BT port. I dont know why but it wont let me create any ports.
Anyone with the same odd problem?
I had a similar problem, Tytn would only let me choose COM0 (Zero) as outgoing port, and TT works fine with it. However, I would like to add Mapking for Asia, and this navi soft will not accept a GPS on COM0. Anybody understands why Tytn is only offering COM0 as outgoing ports for GPS?
I have set the com4 as outgoing port and now tomtom seems to work fine.
thanks for that info.
I don't know why only port 0 and all other ports are blocked but TT works for me now. I only need to wait for a better ROM and i can leave my Wizard home
I have written to a good contact at HTC since I need COM ports other than 0 for Asian Mapking navi soft (in add. to TT) . Will keep you posted.
Answer from HTC:
"As my testing, the Outgoing port is not limited with COM0. PaPaGo can accept with COM0, COM2, COM4, COM8, and COM9. I think the limitation of COM0 is the software limitation of TOMTOM, So if the user wants to use Mapking that only support COM1~7, he need delete the outgoing port COM0, and reassign another COM port for the BT GPS."
I imagine the problem lies between the Tytn and TomTom only, and other navi soft would find other COM ports. But I am kind of hesitant to interfere with a working TomTom, and go through the outgoing COM port game again...
I'm using Navigon and set up an outgoing Connection on com2 and it works fine for me.
sounds like TT is the problem ...
greetz
sphings
Guys, let me try to help you a little bit, as I work in navigation software development (Destinator).
1. The COM ports has nothing to do with the actual software you are running. This is pre-defined in the ROM you are using. That is also the reason why we see variations here - we use different ROMs.
2. In order of enabling a COM port, you do NOT need to discover the GPS icon on the settings. It is quite useless unless you wish to work simultaniusly with more than one software.
3. To enable a COM port, after you pair the GPS, look down for the tab COM Ports in the BT settings Manager. You only need to create Outgoing COM.
4. Strange but usually you will only be able to choose between 2 COM ports. The rest are hidden by the OS. MAKE SURE that you disabled the "Secure Connections". Default key for all the GPS receivers is "0000" and for Globalsat 308 is "2003". The last is AKA HP GPS.
5. If you cannot enable any other COM port than COM0, this is a ROM problem and you should contact your ROM provider like the mobile carrier. You can also try to enable other COM ports with the attached CAB file. Simply run it, it will expose all COM ports for you and now you should start trying. I reccomend to test COMs 4-8 first, normally, it will solve your problems. (Note: I got this file previously here and did not create it myself).
There have been may posts about TomTom not recognising B GPS's.
One solution that doesnlt seem to be mentioned here id to ensure that the name of the GPs in BT connections actually ends in "GPS"..
If it doesn;t renove the pairing and re-pari , but change the name this time to something that ends in "GPS"...
good luck
Charlie Grillo
Thanks guys, found another solution that works for me now:
1) Set your Bluetooth GPS to another COM port than 0 (TomTom´s standard port 6 was not available, so I choose 2)
2) open Programs/Navigator/navigator.cfg with a text editor, change COM0 to COM2
3) start TomTom - working on COM 2!
Started Mapking, found COM 2 - working now.
hello fellas,
as you can see im new here. im thinking of buying the TYTN, a sector which i have never explored before (pda sector).
it sounds great with the applications and due to my work, a need for a pda is becoming bigger.
i posted in this message due to the GPS topic.
i got a very stupid question which you may recieve occasionally if i buy the tytn.. :twisted:
why do a person need BT enabled GPS? i read you can connect it to your PDA but for what reason?
thanks in advance and apologies for any inconvience..
@D_G - welcome to this board
In order to run navigation software on your Tytn you need a external GPS connected to it. Easiest solution is a external GPS connected via Bluetooth.
Another solution would be to buy a PDA phone with a GPS receiver on board, for example the ETen G500.
Of course we would all be interested in a UMTS PDA with integrated GPS, with acceptable battery life, but that will take some time...
thanks lucas for the answer. but why would you need a navigation software if you have a GPS device? in either case you will need to have both devices in a particula blue tooth range. right?
this means you will need your handheld device + the GPS to activate the navigation software, or dd I miss something?!
Hi,
I seem to be having a problem with GPS bluetooth related connections with my Dopod 838 Pro.
Ive paired my Globalsat BT338 receiver and setup an outgoing serial port on my Dopod, and I can use Destinator 6 and TomTom 6 fine (for the time being).
The next day/time when I try to start the GPS applications, both programs report that they cant find the GPS signal/receiver even though its been correctly configured to work previously.
I then have to enter the Bluetooth settings to change and assign another outgoing serial port and reconfigure the GPS applications to the new serial port to work.
The programs and the GPS receiver worked fine with my old iPAQ hx4700 so its not a receiver or program issue.
I'm at my wits end and would appreciate any info on solving this problem.
Thanks in advance.
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Rik_053 said:
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Click to expand...
Click to collapse
Hi,
Ive been through this unpair / pair scenario more than a few times and Ive never used a secure com port connection.
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
njay22 said:
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
Click to expand...
Click to collapse
Hi,
The pairing has been done before any program was launched.
Im trying with both destinator 6 and tomtom 6
Bluetooth GPS Woes...
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
clearwave1 said:
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
Click to expand...
Click to collapse
Hi,
Both the bluetooth reciever and the software work fine and obtain a fix.
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
the gps reciver obtains a fix but the pda cant see it.
Destinator PN has an automatic reconnect tick box on the GPS Settings page. I don't know if D6 or TT have a similar thing. If so, make sure this box is ticked.
I use D PN with a Parrot CK3300 combined handsfree and GPS receiver, and after major stuffing around trying to get D PN set to the correct port initially, it has worked fine since.
Ive sorted the issue out and hopefully this will help others experiencing the same problem.
The problem was that although an outgoing serial port was setup, for some reason it was not mapped to the bluetooth device.
It just specified "COM9" instead of having the bluetooth device "BT338(COM9)" under the bluetooth COM Ports setting.
This seems to be the reason why when the device was unpaired/paired and a com port setup it worked for the time being. After the bluetooth device was disconnected the settings mapping to the device were not retained.
Rambler76,
I am looking to get a GPS unit for my Dopod 838Pro. Which of the two, Destinator or Tom Tom, do you like best?
I know where to get Destinator 6 in Sydney, where does one get Tom Tom 6?
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
killabeezz said:
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
hi,
what i mean to say is that i switch com ports.
the issue was resolved by mapping the com port to the bluetooth device.
Click to expand...
Click to collapse
Yes I understand what you have done but can I ask again :-
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Thanks,,
Tom Tom Woes
Hi,
I had the same problem until recently.
To fix I did the following:
Delete pair with GPS receiver,
Create new pair with GPS receiver (put in passkey 0000)
Tick the box for Serial Port
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Now open TomTom, Select Change Preferences, then Show GPS Status, then Configure, then Other Bluetooth Receiver, then Select COM 4.
Now TT works as it should - turning on and off Bluetooth on Open/Close, and no problems with needing to re-pair.
Previously I had always paired the BT GPS on COM 0 with Secure ticked. This worked the first time only, and I had to re-create the same pair each time I wanted to run the app.
Hope this helps some of you.
(btw I was using TT6 when I found the solution, but I imagine it would have worked for 5 too)
dopod bluetooth problems
Guys I have the same problem with my bluetooth and my dopod. It connects then disconnects.
I have also noticed that the systems unchecks the turn on bluetooth check box and the make this device discoverable to other devices.
Does anyone have any ideas?
Guys I just read this at another forum.
"The Dopod 838 pro and WM5 have chronic problems with the bluetooth stack, which is why everyone is waiting for the new ROM to appear, which will hopefully be WM6. HTC (manufacturers of Dopod 838 pro) announced that the new ROM will fix all of the known problems"
This I learn after having a car accident (minor) in my car playing with the bluetooth and trying to get it to work. Hutchison 3g should only be selling these with a warning.
I assume there is also a problem with the JasJam as they are the same phone.
Knight__Mayor said:
Hi,
To fix I did the following:
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Click to expand...
Click to collapse
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
dabs1 said:
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
Click to expand...
Click to collapse
yeah i recon its the screwy MS bluetooth stack, im interested to hear from anyone running tomtom on hermes with the widcomm bluetooth
Tomtom And Gps
I have found that the best cure for gps woes and pocket pc is to use GPS Gate. It make a virtual com port and will always be the same. I have used it always and never have problems connecting.
G
Hi Team
I need some help from others that have tt6 running on an XDA211i
Any body out there ??
I think I am having the usual problems with com port set up ?
Havnt tried GPS Dash yet but that thats my next stop .
help needed
Astro1
tomtom 6 works fine on the xda2i, i know i was running it,till someone stole the device. Just turn off beam (click start > settings>connections>beam) and then pair the gps,once paired add a outgoing com port on the device(click com ports at the bottom).
Then run tomtom setup and choose your device in the config,if it isnt listed choose other bluetooth,then choose the com port you selected as the outgoing port and it will work
Add an outgoing com port
Hi Scousemartin
Great to hear from you , I have been struggleing with tt6 for waht seems like ages now .
I can follow uyou all the way to add an outgoing Com port ? clock on com port at the bottom ?
Ive paired and then cant find where to add am outgoing com port on the device ( Click com ports at the bottom ??? dont have a " com ports at the bottom ?? )
I can look at the device and it adds the bt gps as outgoing port 6 , when i put this in to tt6 and turn both on the gps flashes furiously but as far as TT6 is conceerned it keeps the " no gps device " sign and no spinning disk either.
No other progs seem to ba able to run a gps either on my machine , maybe this is significant ?
Astro1
sorry for not getting back earlier astro pm me a msn or yahoo address and i will talk you through it, what version of tomtom 6 are you running?
Hi Astro,
Have you fixed your problem yet? I am also running TT6 on an XDA IIi with no problems. Might be able to help...