Related
HI
i am new to this plaise help
i got SPV M1000 witch i install TOMTOM 4.00
the problem is when i click on tomtom navigator
i get this massage: gps position unreliable
plaise tell me STEP BY STEP how do ACTIVATE GPRS
coz i am new to this
tnx
Nice and easy....
Launch TT, goto config, goto GPS
If you have a little circle at the top right spinning then it's connected to your GPS device, however if you get a popup asking you to pair it, then do the following
Search in BT, you should find the GPS device, pair to it (dont use a code if asked)
Tick the allways connect to this device tick box, ok all the way out and TT should now be talking to the device
It will take a while to initially pick up satelites, you should see some grey bars and numbers in the GPS window inside TT.... Also make sure your outside
Hi King2,
are you getting GPS and GPRS confused?
you don't mention a GPS unit in your post (but you do mention GPRS)-- do you have one? TT is useless without.
the GPS unit (usually cabled/bluetooth) is basically a satellite receiver which TT uses to locate your position.
Hi,
GPS Position Unreliable means that the GPS Module not found any satelites.
When you don't have the module you don't get this message.
Then TomTom says GPS module not found.
I takes about a minute or so to conect to a satelite.
But you must be in a open space otherwise the module can't connect.
When you are between buildings the connection is difficult.
Hope this helps
Greetings [email protected]
COM PORT HELP????
HI
TNX FOR HELP
i upgrade my SPV M1000 from win 2003 to 2003SE and the
GPS TO V 3.07 the problem i got is:
on the bluetouth settings,bluetouth serial port setup:
INBOUND COM PORT:COM4
OUTBOUND COM PORT:COM5
now on the GPS TAB
on the top drop i got TOMTOM NAVIGATOR GPS
and on the second drop i got COM 5
now I CANT TICK THE BLUE CHECKMARK BOX TO START THE CONNECTION but before i upgrade to win 2003SE it was OK
any help plaise and tnx
----------------------------
ROM version:2.06.00WWE
RADIO version:1.18.00
EXTROM versionIAMOND 1.2se
Port Problem
Hi King2,
Did you paired the phone and the BT GPS?
It is where you put the BT on
Settings / Connections / Bluetooth / Devices / New
If you did there was a question about a bluetooth serial port connection.
You must answer yes or no. Use yes
If you tick yes, WM2003SE creates a BT Serial port.
I think in the text it also says what port was created. (i saw in a flash that is was BT Serial Port 5
In TomTom got to GPS and take BT Serial on Com 5
Uncheck the port 4.
I din't change the settings and when i just looked in the BT Settings only the Outbound Com port: 5 is checked and 4 is not
I hope this helps
Greetings [email protected]
COM PORT HELP???
HI
TNX FOR HELP
NO I CANT paired the phone and the bt gps: DEVICE NOT FOUND
I DONT get any question about a bluetouth port connection
but in TOMTOM GPS I DO TICK THE COM 5 in second drop
the problem is i CANT TICK THE BLUE CHECKMARK BOX TO START
THE CONNECTION
is ok with COM 4 but no COM5
COZ IF I CANT TICK THE BLUE BOX TO START THE CONNECTION
I CANT PAIRED?
any chance to change the COM PORT settings in BLUETOUTH SETTINGS?
tnx again for your help
Hi King2,
You must pair your BT GPS otherwise it won't work.
What for BT GPS do you have :?:
And did you put the GP on when you try to pair. (it a silly question but i have to ask you).
Did you BT GPS came with extra software :?:
Were going to get it to work :wink:
TOMTOM GPS
HI [email protected]
tnx for your help
IT S ALL WORKING NOW
i did paired them and it s working like dream
your r top man
Hello, i've installed Tomtom 5.21 and the maps and everything is ok. but i can't make the link between my gps reciver (Royaltek Star III) and the atom XDA. I've installed the partnership in the settings but it doesn't connect with the antenna. I've seen in my other pda (ipaq hx4700 and ipaq hx2790) that there is a bluetooth manager in the connection setting but there is non in the atom xda. Do you know what's the solution ?
Thanks
create OUTGOING COM port for GPS device
The same problem again
I've tried but i can't choose the port i want and if i choose another one, i can't find it in the gps settings in tomtom.
tomtom use 8 COM port. so.
1. Settings=>bluetooth=>mode
2. check all boxes
3. Settings=>bluetooth=>devices=>new partnership
4. pare GPS
5. Settings=>bluetooth=>COM ports
6. choose device=>NEW OUTGOING port
7. assign your GPS device to 8 COM port
thats all.
Can't chosse com 8 in Tomtom
Ive tried in Tom tom to choose com 8 but the only ones i can choose are com 2, com 3, com 4 and com 9. And if i want to chose one of theses for pairing, it's refused. I don't know what to do
dont forget, you need to set a new incoming port too, just play about with differnet comm ports until one works, keep the gps in search mode until the atom sees it, assign a comm port to it and see if the gps screen picks up a signal, takes a bit of time, but generally always works
Not working
I'm using a gps antenna in bluetooth but it isn't working, there is no link between the antenna and the atom. On other pda you have the bluetooth manager and you can make the link in manual mode. I don't know why i can have the com8 in tomtom options. The antenna is never blue, there is no link between
bryson
you need to set a new incoming port too
Click to expand...
Click to collapse
no you don't. you can only receive information from GPS, not to send it.
dragsterbox
check PM
I did it
I did it but it's not working, no changes
did you assign for GPS 8 COM port?
by the way, do you have tomtom 5.21 for WM5 devices?
COM 8
In the bluetooth menu, first, i've the gps associated on serial port. The outgoing port on com 5 and the incoming port on com 8. But in tomtom i've com 3,4,5 and 9 avalaible but on the atom i can't chosse theses ones. That's the problem and i've no link made between. And there is no way to make it in manual mode
look, I sad clearly:
create OUTGOING!!!! COM PORT.
then assoshiate it with 8 com port.
you say:
incoming port on com 8
Click to expand...
Click to collapse
and
it isn't working
Click to expand...
Click to collapse
you dont understan why? I thing you don't see the difference between Incoming & Outgoing port.
I sad:
bryson
Quote:
you need to set a new incoming port too
no you don't. you can only receive information from GPS, not to send it.
Click to expand...
Click to collapse
you sad:
incoming port on com 8
Click to expand...
Click to collapse
I have no comments. Good luck!
P.S. I have TomTom Navigator with bluetooth GPS on my Atom. It working perfectly.
Nothing's working
Impossible, nothing's working. There's no connection between the antenna and the tomtom.
In Tomtom the avalaible ports are : com 2, com 3, com 4 and com 9
On the atom, bluetooth is in discoverable mode and i've created a partnership with the antenna. I've created an outgoing port on com 8 and for the incoming port in com0 because i can't choose com 2, com, com 4 and com 9.
I really don't know what else i could try
I am trying to set up tomtom 5.21 with my BTGPS74 receiver but cant get the two to communicate. I know there is some settings you can change in settings/system/gps but the problem I have is I dont have the gps option in settings anywhere. Am I missing something? Does any on know what I should do. Tomtom wants me to use port 3 or 7 but when I try to set them in bluetooth settings it says its not possible check your settings. Any suggestions would b welcome. Thanks.
P.S I know the receiver works as it still works well with my N70.
...you should've gotten a GPS icon if software GPS recognized.
In rgister you can force simulation.
hklm\controlpanel\gps]
delete redirect and add 'group' with dword=2
Then GPS icon will appear.
I gave it programport 7,hardware 6, baudrate=57600
gps auto checked
I'm not sure about the settings...
I had to create incomming and outgoing com ports on my 3100 (not sure if you need both)??
TomTom used com port 9 and works like a dream
as soon as you start the programme it connects automatically as long as my receiver is on.
It even connects when the BT on the 3100 is turned off - it starts the BT automaticlally when tomtom runs!
Yeah i agree all you need to do is set up the com ports, then fire up tomtom and select the com port you just set up and away it goes
Chris
Thanks for the replies guys. I know I have to set the com ports but the problem I have is there is nowhere for me to do this. For some reason the gps settings is missing from the system/settings. I am going to try to reinstall tomtom to see if it helps. Tomtom has ports 3 and 7 showing but they seem to be taken by something else so I cant configure my receiver on either of them.
I have a slightly different problem... my TyTn can connect to the BT GPS reciever, but as soon as TomTom tries to calculate a route, or I click the GPS signal icon it crashes back to the Today screen...
I've got TomTom installed with 5.21 update, anyone had any problems like this?
you just need to pair your bluetooth device go to settings connections and bluetooth and add new device, let your tytn search and it will find a new device when you have paired it select new comm port outgoing
I have no gps setting in control panel either
Cheers
Chris
Hi,
i have a strange problem with my BT. I cant create a incoming or outgoing BT port. I dont know why but it wont let me create any ports.
Anyone with the same odd problem?
I had a similar problem, Tytn would only let me choose COM0 (Zero) as outgoing port, and TT works fine with it. However, I would like to add Mapking for Asia, and this navi soft will not accept a GPS on COM0. Anybody understands why Tytn is only offering COM0 as outgoing ports for GPS?
I have set the com4 as outgoing port and now tomtom seems to work fine.
thanks for that info.
I don't know why only port 0 and all other ports are blocked but TT works for me now. I only need to wait for a better ROM and i can leave my Wizard home
I have written to a good contact at HTC since I need COM ports other than 0 for Asian Mapking navi soft (in add. to TT) . Will keep you posted.
Answer from HTC:
"As my testing, the Outgoing port is not limited with COM0. PaPaGo can accept with COM0, COM2, COM4, COM8, and COM9. I think the limitation of COM0 is the software limitation of TOMTOM, So if the user wants to use Mapking that only support COM1~7, he need delete the outgoing port COM0, and reassign another COM port for the BT GPS."
I imagine the problem lies between the Tytn and TomTom only, and other navi soft would find other COM ports. But I am kind of hesitant to interfere with a working TomTom, and go through the outgoing COM port game again...
I'm using Navigon and set up an outgoing Connection on com2 and it works fine for me.
sounds like TT is the problem ...
greetz
sphings
Guys, let me try to help you a little bit, as I work in navigation software development (Destinator).
1. The COM ports has nothing to do with the actual software you are running. This is pre-defined in the ROM you are using. That is also the reason why we see variations here - we use different ROMs.
2. In order of enabling a COM port, you do NOT need to discover the GPS icon on the settings. It is quite useless unless you wish to work simultaniusly with more than one software.
3. To enable a COM port, after you pair the GPS, look down for the tab COM Ports in the BT settings Manager. You only need to create Outgoing COM.
4. Strange but usually you will only be able to choose between 2 COM ports. The rest are hidden by the OS. MAKE SURE that you disabled the "Secure Connections". Default key for all the GPS receivers is "0000" and for Globalsat 308 is "2003". The last is AKA HP GPS.
5. If you cannot enable any other COM port than COM0, this is a ROM problem and you should contact your ROM provider like the mobile carrier. You can also try to enable other COM ports with the attached CAB file. Simply run it, it will expose all COM ports for you and now you should start trying. I reccomend to test COMs 4-8 first, normally, it will solve your problems. (Note: I got this file previously here and did not create it myself).
There have been may posts about TomTom not recognising B GPS's.
One solution that doesnlt seem to be mentioned here id to ensure that the name of the GPs in BT connections actually ends in "GPS"..
If it doesn;t renove the pairing and re-pari , but change the name this time to something that ends in "GPS"...
good luck
Charlie Grillo
Thanks guys, found another solution that works for me now:
1) Set your Bluetooth GPS to another COM port than 0 (TomTom´s standard port 6 was not available, so I choose 2)
2) open Programs/Navigator/navigator.cfg with a text editor, change COM0 to COM2
3) start TomTom - working on COM 2!
Started Mapking, found COM 2 - working now.
hello fellas,
as you can see im new here. im thinking of buying the TYTN, a sector which i have never explored before (pda sector).
it sounds great with the applications and due to my work, a need for a pda is becoming bigger.
i posted in this message due to the GPS topic.
i got a very stupid question which you may recieve occasionally if i buy the tytn.. :twisted:
why do a person need BT enabled GPS? i read you can connect it to your PDA but for what reason?
thanks in advance and apologies for any inconvience..
@D_G - welcome to this board
In order to run navigation software on your Tytn you need a external GPS connected to it. Easiest solution is a external GPS connected via Bluetooth.
Another solution would be to buy a PDA phone with a GPS receiver on board, for example the ETen G500.
Of course we would all be interested in a UMTS PDA with integrated GPS, with acceptable battery life, but that will take some time...
thanks lucas for the answer. but why would you need a navigation software if you have a GPS device? in either case you will need to have both devices in a particula blue tooth range. right?
this means you will need your handheld device + the GPS to activate the navigation software, or dd I miss something?!
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Had no problems pairing my BT Slim GPS with my Vario II, TomTom runs fine.
What GPS receiver you using ?
works fine on my xda trion as well.......im using tom tom 5.21 with BT-338 gps receiver.......im also using com port 0......you basically have to pair it and then add outgoing port as com port 0.....and during the installation on tom tom make sure you choose com port 0......that worked for me anyways....hope that helps.
Bluetooth GPS HTC TYTN
Thanks guys have re-installed tomtom and now it comes up with com prt 0.Probably didn't install correctly first time .Now up and running .Fantastic!!!!
I could cry
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
mobilecat said:
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
Click to expand...
Click to collapse
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
OUCH
dew.man said:
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
Click to expand...
Click to collapse
I tried running this but i can still only assign certain points from my bluetooth manager and dont have these displayed on the tomtom menu.
When you go into the GPS Status settings on Tomtom and tap configure, have you tried looking to see which com ports it lists and then going back to the bluetooth settings and doing trial and error to allocate any of those port numbers as an outgoing port for your GPS unit?
For my genuine Tomtom GPS unit, I did not even have to set up a port, I just had to pair the device but when I used a friends alternative brand of GPS unit for a short while, I was only able to get that one working under Com port 4. I can't quite remember but it may even have been a case that Com 4 only became visible in the Tomtom GPS configure menu after I had allocated it as an outgoing port for the GPS device (sorry, it is a while back so I can't quite remember the order in which I set it up)
Hope you get it sorted
arghh
I a so annoyed. I did this and had no luck. Later on I did something and got the option for port 2 and used it and it was great. I had to do a soft reset for something else and I cant do it again. tried everything.
MMMM
Happy yet frustrated
I have deleted create ports from my device as it only works once. I have reset my device. I reinstalled createports and extracted the file. I then saw port 2 straight away - the one that had been missing in tomtom.
The only problem is that if I do a soft reset I have to do that again!
It is very frustrating trying to get some of these things working. Have you thought about upgrading to Tomtom 6? you may find you have less problems getting the pairing and ports working right.
Failing that, I am sure you will be able to get it working again, just keep trying all the com ports one by one until you find one that appears in the Tomtom configuration. Like I said, on my XDA Vario II (Hermes) I managed to get it working on Com 4 and when I had an XDA Mini S (Wizard) I seem to remember that it was either Com 6 or Com 7 which worked on that one.
You might want to check the bluetooth settings for security and beam as well. Try turning security off (ie. passkey required off) and make sure the beam setting is ticked to receive all incoming beams.
I will keep my fingers crossed for you
download co-pilot for uk
Dashley said:
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Click to expand...
Click to collapse
Any one got the co-pilot softwear to insallate for MDA VARIO 2.
download co-pilot softwear for UK.
Any one got the co-pilot softwear to insallate for MDA VARIO 2.
another thread
I have just seen another thread about XDA with a patch for this that seems to work. Can someone merge the threads?
Createports
Can anyone point me in the right direction to find this program. I think that it is hidden on the web somewhere near the holy grail.
Help with TT6 + TYTN + Royaltek 2110 please
I have a TYTN and a GPS Royaltek 2110. I have position com0 and other programs GPS work correctly. The problem is that the TT6 always shows he himself message “GPS nonfound”, although always I can say to him that this in the COM0 but does not find satellite.
That I can do? I put the TT5
somebody it has the CreatePorts program and it can put it?
Thanks
try this thread:-
http://forum.xda-developers.com/showthread.php?t=288865
Pairing TOMTOM 6 with Bluetooth GPS
For all of you that are having problems pairing your GPS Bluetooth receiver with your Hermes see the instruction set below:
#Hermes can not be in flight Mode#
1st: Run BTHTools1100.exe
--------------------------------------------------------------------------------------------------
2nd:
Pair them in Bluetooth Manager
Set:
Holux (outgoing port com4)
Incoming Port (com8)
no security
------------------------------------------------
3rd:
In settings >> Connections >> GPS
Programs set GPS program port to Com 8
Hardware set GPS hardware port to Com 4
baud rate 4800
If GPS program is not seen in settings\Connections
Use resco registry or other program and:
Go to Hkey_local_Machine\ControlPanel\GPS settings\ creat (make new) "Group" with Dword data =2
---------------------------------------------------------------------------------------------------
In TomTom chose:
Bluetooth GPS
Com4
should be working Now
Pairing TOMTOM 6 with Bluetooth GPS (easy) - Kaiser
First after reading the posts I thought I had to reinstall Tom Tom or install another software. Luckily, I paused and read the message when I was about to configure my other bluetooth receiver. It said, first you must establish your bluetooth connection. Well, I lied coz I did try to go on and couldnt find COM 0 or whatever you guys have said.
But that's what I did, eventually. Paired the device as BT GPS, check the serial connection (not sure if secure connection needs to be checked but I left it unchecked to find out later). After that go to com port tab, and click add new port ie selected COM0.
Then go back to TT6 (restarted in my case), and to other bluetooth gps receiver then found COM 0 in there. Voila!!
Chose COM0, but still got no gps device message. Waited for about 2 mins while reading further into the posts and now my TT6 is working.
You could call that strike of luck I dont really care but yeah.. saving some batt power on my kaiser for the bank holiday;s trip. Have a great one everyone!!
P/s: Mine is O2 stellar on Dutty's great work.
Com 4 is the only one that works with Schaps 3.54
Dear Htc fellows,
My bluetooth GPS is working strange on my Universal, but on iPaq with
WM2003 works as a charm. The BT GPS is new Solar GPS with new Mediatek
chipset.
It's not working with iGo 2006 and even not Tomtom 5 or Tomtom 6.
I can find the BT GPS in BT manager, I can pair it, but I dont know why,
it needs a pass key even if it shouldn't. Then when I explore it's
services, The popup come again asking me if I will allow external BT
device to connect to my Universal and it come asking passkey again (Why?).
I can't even enter an empty passkey (bt device doesen't require it). After that I have successfully paired the device. I can add it's serial port to enumerate on com ports 8 or 4.
When I start Tomtom, it doesent detect the device at all. If I use iGo, it detects, gets datas and disappear, it's allways appeared for 1 second and then 5 seconds not. No matter Which bitrate I set (device is written to be 9600) it needs to be in NMEA protocol, not SIRF.
When I use some freeware GPS programs, it seams to be working ok, it shows satelites and it's not disappearing.
What can I do with that???
I have some idea that it's probably about WM5 and it's security....
How can I setup com security in registry? can I set the port speads manually atd... I had performed a hard reset and it still don't work. Can ROM update or AKU update help me?
Does anyone have some idea what should I try now?
O2 XDA EXEC:
Rom: 1.30.107
Radio:1.09.00
P:42.42.P8
BT GPS: model: BT 2.5MR
made by f-tech.com.tw
Thanks;
Shef
Could you find a solution??
Hi,
I have the same problem exactly and could not find anything on the net. Did you solve your problem?
well ...
i know that there is a problem with GPS and WM5 and so there is this patch which i install every time i hard reset .....
the guys i bought MY GPS from gave me this ... and they are pretty knowledgable .....
it works well ....
try it !
tried
My OS version is WM2003 but tried anyway.. Did not work.. can there be version for WM2003??
did you ?
did you define an outgoing com port for the device (com 4 for example ?)
com port definition
well, igo finds the device an COM 6 actually, it connects too.. but stays connected just for a second, then again and again..
I installed GPSGate and created a virtual com port 7. I manually configured the GPS receiver connection to COM 7 on igo.. But all the same.. :
do you advice another way?
one other thing the device works with navigon 5.0 and tomtom 6.0 smoothly, no problem.. only igo..
well...
IGO is CRAP ... that is well known .... lots of bugs ...
i am sorry .. i do not know how to solve your problem...
but i suggest using destinator 6 ..... (that's what i use) ....
simple ... nice looking .... big buttons and able to navigate to your contacts directly (especially useful if you have Phone Edition)
oh ... and ... works great !
I got the Holux GPSlim 236 GPS. I can pair the GPS with Universial. But I cannot set the com port at all. A pop up window always say the com port (I tried everyone of the ports) is not available.
Any one got a solution, does the GPS bug fix help ? and what does it fix ?
Might seem a bit obvious, but have you tried the code "0000" when pairing your device?
Once paired...did you define an outgoing serial port on "Bluetooth Settings" menu on your WinCE?
I have a royaltek bluetooth GPS and it's been working well with TomTom[5|6]...I use '0000' as passkey (default on many 'non-interactive' devices), once paired I clicked on 'COM Ports' tab and defined a new outgoing port, the wizard should list the GPS as an available device to create a COM port so I used it and I got a 'com0'.
Once the outgoing port was created I had to tell TomTom to use the new 'com0' and worked like a charm
It's been working since TomTom 5.21 (previous versions didn't work).