Related
Hi all, very frustrating, I bought an SPV M1000 on 2nd Feb 2005 and this morning - 12 months and 26 days later it has a complete failure.
Both batteries are fully charged and have tried this through the Desk charger (Green Light), and my In car charging kit.
If I put a battery in the M1000 and placeit back in the desk charger or the car kit - I just get the charging light being Red - Not Amber or Green.
I have tried a manual quick reboot and a main reboot but nothing at all.
Does anyone have any good advice as to what the problam may be as Orange were not very interseted being 26 days out of warranty.
What caused failure ,? did you let battery run down completely, have you by any chance damaged bottom plug placing it in cradle,?(friend of mine did and he had similar problem). does nothing at all happen when you try to turn on ? check battery contacts on phone to see if damaged. finally check internal backup battery( similar size to 5p) you should get at least some response. if you ever wish to sell for spares I am looking on here for a replacement screen for mine let me know if you decide to sell at [email protected]
I have an 02 XDA IIs on 2003 updated to most recent software for 2003 via o2 site etc
Ok so I took my PDA away for a few days over christmas and the batterry ran down, and I had forgot the charger so obviously it wouldnt turn on.
I got home and put it in the charger cradle, and it wanted to do a hard reset, so I went through with that and after a few seconds the screen goes black and it then goes ding and up comes hard reset again.
It does not hard reset at a certain point of setup as if you do the process quicker it will still hard reset say after, 10-20 seconds, usually the same every time I think.
Whilst off the cradle, you cannot even switch it on and no light shows or soft reset does not work.
In the cradle only the above which I described happens...
Any help is much appreciated
Sam England
hi.. seems to be a real trouble... anyway try to re-load the rom on it... use your wm2003 cdrom or dowload from p2p or forum wm2003 on your language, then try to flash the device following on screen infos...
hope this will help,
all the best,
storm
Have you checked your sync port?
Sounds to me like pins 20,21,22 may be damaged in your charger (sync) port, one may be touching the body of the port and causing a short, creating a hard reset. Also this might be the reason why it is not charging. IMHO regards
hi sam england
is your cradle plugged into the wall socket? usb does NOT provide enough energy for the device to 'survive' the reboot. i have this 'problem' almost every time i let i discharge to much.
so plug a good idea is to charge your device with the supplied separate charger.
hope it helps ....
regards ize|man
hardware button problam i think..............
i think that your both hardware buttons softrest and power swich are jam or lock thats why it doesn't work and because of them the phone get hardreset when ever you plugin charger or cradel
if you want any help about hardware of any htc products plz connect me on my e-mail id
if you have a cradle with the battery charger, take out your battery, charge it, and put it back in the unit
It should get through its start up routine
Having not use my exec for a bout a month I now find it will not start or take a charge (battery has 3.8v ) but it will not power up ,it is still in warranty BUT I have changed the rom ,so don’t know if o2 will repair it
If I use the wall charger a LED flashes on for about 1 second ,if I plug in to usb lead on pc (with battery removed) red led comes on any ideas appreciated
towinguk said:
Having not use my exec for a bout a month I now find it will not start or take a charge (battery has 3.8v ) but it will not power up ,it is still in warranty BUT I have changed the rom ,so don’t know if o2 will repair it
If I use the wall charger a LED flashes on for about 1 second ,if I plug in to usb lead on pc (with battery removed) red led comes on any ideas appreciated
Click to expand...
Click to collapse
Problem indeed.... Firstly, I wish I could offer some constructive solutions, but afraid not.... it does sound like a worn battery, and maybe worth trying (or borrowing) another one to flash?
I take it as you refer to it as an 'Exec' that it is the O2 branded one? If it is, from my experience with the O2 technical support, they really don't have a clue. I would assume that they would send an exec straight to HTC for testing. It's a complete last resort, but if you were to tell them that your unit was dead and they were to take it in, they wouldn't be able to solve the problem before they sent it back to HTC. This is of course after you have clarified it's not just a dead battery cell.
Best of luck with the thread and hoping someone a bit more experienced can help.
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery removed?
If this is the case, you might have a dead internal battery charging/power supply circuit, i have repaired some old Ipaqs with this failure, most of them failed due to a defective battery, easily recognized by overheating when the unit was placed in charge, usually the overheating increased slowly in time (months usually).
I don't want to be misunderstood, but all these devices have a way of turning of the LCD backlight, a long pressure on the on button does this, it can restores with the same long pressure, see if this is not your case.
If you have some electrical problem with your PDA you might take it to repair or you could try to do it yourself -if you're able to do it obviously-.
Anyway, try to get yourself another battery (you might ask for it to someone else with a uni), put it on and see.
I'm also assuming that you have tried to hard reset your device.
good luck
kecido said:
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery remo....
good luck
Click to expand...
Click to collapse
Look maybe this will give you some hope. Yesterday I took my Htc Typhon (smartphone) after a long time, the battery was die. I tried to charge via usb, and nothings happened, then I tried to use a usb charger and nothing happened neither. Finally I charged the battery alone on an universal battery charger and after 30 minutes my phone was alive again.
Hope it will help you!
Felipe
kecido said:
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery removed?
If this is the case, you might have a dead internal battery charging/power supply circuit, i have repaired some old Ipaqs with this failure, most of them failed due to a defective battery, easily recognized by overheating when the unit was placed in charge, usually the overheating increased slowly in time (months usually).
I don't want to be misunderstood, but all these devices have a way of turning of the LCD backlight, a long pressure on the on button does this, it can restores with the same long pressure, see if this is not your case.
If you have some electrical problem with your PDA you might take it to repair or you could try to do it yourself -if you're able to do it obviously-.
Anyway, try to get yourself another battery (you might ask for it to someone else with a uni), put it on and see.
I'm also assuming that you have tried to hard reset your device.
good luck
Click to expand...
Click to collapse
thanks for all the help
1 it will not turn or power ,no led no screen
2 battery dose get hot when charging
3 screen has not been dimmed
its back at o2 shop now we will see if they repair it and ill report back !!!!!!!!!
Grilloman said:
Look maybe this will give you some hope. Yesterday I took my Htc Typhon (smartphone) after a long time, the battery was die. I tried to charge via usb, and nothings happened, then I tried to use a usb charger and nothing happened neither. Finally I charged the battery alone on an universal battery charger and after 30 minutes my phone was alive again.
Hope it will help you!
Felipe
Click to expand...
Click to collapse
hi thanks for the reply i have had the same on a m600 ,would not charge from usb or car kit but did start with mains charger
i have tryed hard reset but it will not do that either
battery is stuck at 3.7v even after trying to discharge it with a small bulb
thanks
John...
This is something I've had happen in the past.
Try taking the battery out, and put it into a ziplock back, and place it in the freezer for a few hours. I know, I know, it sounds ridiculous. But sometimes, just sometimes, it will reactivate the cells, and you'll be able to charge it after that.
well done o2 uk
well as said before took my phone back to the O2 shop and sent it off to the service centre. The report came back that the main board US .not only did i get a new exec but But a new boxed one and a full set of all original parts !!
i had this problem when i first got my SPV m5000..i took it to the orange shop...(the people where nice) they kept it for few testing and said...
battary was faulty...so they gave me a new battery XD
Background:
I have had MANY PPC's (so many I can't even count them) and I've loaded many different cooked ROMS and such on most of them so I'm not a complete noob on these things (don't claim to be an expert either).
However, my most recent acquisition is an HTC Advantage bought at CompUSA. I've read most of these came with a test ROM and mine was no different except for the fact that when I attempted to update the ROM to the "official" one provided to me by HTC it would not work. I always got the error "Connection lost" about half way through the process. I tried it numerous times and it never worked. On some occasions it would get stuck on the bootloader screen but I was able to get it back to working status (still on the test ROM).
I decided to try installing step 1 of Ollipro's SPL to see if that would help loading the HTC ROM. Turns out that wouldn't work either. It would get stuck at step 1 where it would ask if "PPC gone idle and didn't work or to wait 30 seconds". Tried it many times and would try to get it to keep going but the grey box on the bottom left would say the "parameters were incorrect" and would give me the option to quit, which I would. No problem, at least my 7501 was still working.
After that I tried the official HTC ROM again and I got the same "connection lost" error I had previously, except this time I didn't get anything on my PPC screen, just a black screen, not even the battery charging light behind the joystick lights up anymore. Soft reset...........nothing. Bootloader reset....................nothing. Hard reset.......................nothing. No lights, nada. The only flicker I get is if I try a reset wheen the power cord is connected. A red light flickers behind the joystick whenever I click the reset button. Any ideas or any help?
Sounds to me like the battery is just dead. I bought one at CompUSA (had the test ROM also) and I got the red ring around the joystick too when I tried to turn it on in the store. I left it plugged in awhile and it finally booted up okay. I then replaced the test ROM with the one and only available for the X7501 on HTC USA's web site. Good luck and I hope you get it working!
I think it could be battery related as well but it had a full charge when this happened. For some reason the unit has lost communication with the battery. I'm at a loss.
I got the same problem like you man !!! but i bad luck and so stupid man , i did with HTC X7501 then it dead after that i bought the X7500 then did it again , holy "... " it dead again....man ...So how your phone now bro ????
I left out the battery a half day and tried it again but still dead. Then I left it charging overnight and tried it again but still dead.
I can't believe this. I've never had a bricked device that can't be revived but after so many have seen this post and still no solutions I'm guessing it's no hope.
I met the same situation when I started to unlock Athena ( TMobile Ameo) within not fully charged battery ( less then 70%).
Solution ( try to make BL mode) with connected wallsocket charger ( not connected to PC USB slot) or find 100% charged battery. It helped me two times.
After many tries it changed to BL mode .
Now I didn't start unlock/change ROM without 100% charged battery.
I have the same BIG Problem, only red fliker when soft reset when AC conected. I wanted to update rom from russian to english and phone stoped working (black screen), and battery heats when inserted in phone . nothing to do? i read everything but i have not got any solution. I think it may be bios dead. helap us please
Lobstrick said:
I have the same BIG Problem, only red fliker when soft reset when AC conected. I wanted to update rom from russian to english and phone stoped working (black screen), and battery heats when inserted in phone . nothing to do? i read everything but i have not got any solution. I think it may be bios dead. helap us please
Click to expand...
Click to collapse
"heating battery" (i.e. discharging when inserted, you mean?), no charge led = dead bootloader indeed.
I get the same problem. My device is work, but not charge. Also like yours i have red ring around the joystick when the battery is taked out. And if battery inside, when i make a softreset it blink one time, continued to load but not charge.
You`r speaking all wonderful. But have anybody found the solution?
Hearing these stories makes me nervous. I'm on the stock ROM (mine came from CompUSA with the latest ROM and I don't have an urge to try the cooked ROM yet). I've been using my Athena daily for 4 months, it charges correctly from several different chargers I have (car, computer USB, stock wall charger, aftermarket wall charger).
However, one day 2 weeks ago I went to make a call in the middle of the day and my Athena was dead. D-e-a-d. Usually I can make it back home at night and still have 90-100% on the battery meter, so with no use in the middle of the day and a dead battery, this was weird. It wouldn't turn on, no soft boot, took the battery out and put it back in, and always got nothing.
I bring this up here because when I plugged it in, I encountered similar problems that others here are describing. It wouldn't turn on, and it didn't give me the orange charging light behind the joystick. I ended up leaving it plugged in for a while and finally I got a red ring, not the usual orange. I've only seen red when the battery was almost dead and the unit was on. Then after some more time the ring turned orange and at this point it would turn on again. I still have no idea why my battery died so fast and hard.
So, is there a problem with the battery charging system that is starting to crop up in units that have been used a while???
miha_conan said:
I get the same problem. My device is work, but not charge. Also like yours i have red ring around the joystick when the battery is taked out. And if battery inside, when i make a softreset it blink one time, continued to load but not charge.
You`r speaking all wonderful. But have anybody found the solution?
Click to expand...
Click to collapse
Hi i am no expert but i had simaler problem no display or no lights round ring no responce to any commands (ie hard reset and bootloader ) only red light flickred on reset button all i did was removed battery while pressing reset button and placed new battery and left it on wall charger for couple of hours and before doing hard reset i pressed reset button 2 to 3 times and green light round the battery came up so i tryed bootloader and it worked and insted of flashing it with pc i just loaded the img in sd card and flashed it while whole thing was on charge (i had tmob test rom before ) which i think is best way to do no hassle of losing connection or failing in half way and it works like a charm
hope this helps
and ya if you have a spare battery it dose help
New battery?
I'm a wizard user (and lots of former PDAs) looking to buy and Athena, maybe.
Has anyone tried a new, right out of the envelope, battery? these issues sound like worn out Li-Ion batteries to me. I've had them completely conk (won't take a charge at all) if I let them go completely down, and I've had them wear out and stop taking a full charge (down to maxing out at about %20, but sometimes showing %100 depending on ROM status) when I kept charging them while they're already charged.
Li-Ion batts don't sit for long periods too well, either, so if they're sitting on the shelf at the store/warehouse, they may be suffering even more than one that has been used since earlier in its childhood.
Perhaps the answer is a switched charger that stops charging when the battery (not the ROM/unit reading) gets to %100. ???
I didn't see anything like this posted. I'm terribly curious to see if anyone can resolve it.
nother AMEO dead
http://forum.xda-developers.com/showthread.php?p=1859021#post1859021
Red ring comes for a sec only try to RESET the device with Charger connected
Click to expand...
Click to collapse
same here,
i am afraid i got a dead athena too, did you guys found any solution?? i tried switching batteries. this is my first experience with a windows mobile device not powering on, in inrepairable condition.
found another member with similar problems- http://forum.xda-developers.com/showpost.php?p=1639311&postcount=24
No genius,s on here,just insults
i have read every page on the advantage x7500,being such an old phone you would thin the genius,s on here could sort it out in seconds,but all they do is insult you.i tried to update from windows 6 on radio 1.20 to michys radio 6.5
it got to 94 percent then crashed, now when i boot up i just get a black and white screen,which then turns white,if it try to reinstall advantage 6.0 the phone reets after 2 or 3 percent..will anyboby help by giving simple term advice to unbrick it? NO.will they provide links to there advice no.THEY JUST INSULT YOU AND SAY ITS IN ONE OF THE THREADS.well im a computer tech and if anybody wants there pc or laptop fixing.guess what i will return the favour with computer speak,THAT YOU CANT UNDERSTAND
hello, sorry for my english, but i'm italian;
i have a little problem with htc pu10 (universal) branded o2 xda exec:
when the battery charge go to 40 / 35 %, the pocket device is automaticaly turned off, and the only way to turn on the device is connect it to a pc, or battery charger.
When i do this, the led flashes red for a little time, and after 15 seconds become orange, the charge begins, and the device is turned on.
why this??
i have purchased the device 2 years ago, has always done so, but now i need to use it as modem, and the battery and the battery last very little.
please help me!
Welcome to forums
The best you can do is replace your battery
Have a deep read here also:
http://wiki.xda-developers.com/index.php?pagename=UniversalSmallBattery
And:
http://wiki.xda-developers.com/index.php?pagename=UniversalBatteryIssue
ok thank you for the answer, i try to search and purchase a new battery pack on ebay, and i try to use it, if the problem is resolved, better, else, i rewrite in the forum.