Related
I have a new Wizard (O2 XDA Mini S) which refuses to connect to my Belkin Pre-N router.
Despite trying all I can think of, including Encrypt On/Off; WEP, WPA; b/g mixed access; changing Channel and SSID, reset to defaults etc, etc I still get no joy.
I even suspected a hardware fault with the Mini, so had it changed, but the new one is the same.
When I start WiFi, the Mini finds the Router, and requests the WPA key. Once supplied, it just goes back to "Available" in the list of connections; forcing a "connect" shows it trying to connect, but it just returs to "Availabe" again. The network properties shows no connection (no SSID or Channel) and no signal strength.
All my other WiFi clients connect fine- O2 XDA Exec, Toshiba Laptop and another PC client. Even my old Ipaq with jacket connects, so its not a b/g problem.
I've even tried using the 802.11g registry hack cited in another thread to no avail.
The Mini did connect to a BT Openzone Access point this morning, so the capability is there.
Connection settings for the connection are for "The Internet" and the overall network card settings (above the Network adapter list) to "Work", though I did try this with "The Internet" out of frustration.
Any ideas guys?
Neil
I have had the same problem. As soon as I put the hack in I cant connect.
Take the hack off and it connects. Belkin pren adsl router
dalewinterstein said:
I have had the same problem. As soon as I put the hack in I cant connect.
Take the hack off and it connects. Belkin pren adsl router
Click to expand...
Click to collapse
Thanks for the advice, but I tried it without the hack first- no go, and have now done a hard reset (I've done so many hard resets I've lost count!)
Everything I try fails. Just about to try the firmware update for the Router.
Sorted- the router firmware update fixed it!
NeilM said:
Sorted- the router firmware update fixed it!
Click to expand...
Click to collapse
So you are saying that the router was the one causing the issues, you think, and not the Wizard (MDA)? I have the same issue. Have the hack (g) installed. I was only able to connect once to the my Belkin pre-n...but for some reason cannot get an IP address...ever...
I think it was a combination of the 2 things:
The G HAck on its own did not work, and the firmware update on its own didn't work, but updating the firmware, and using the G hack allowed my Wizard (O2 Mini S ) to connect and it has been fine since.
In fact I've now applied the "Linksys Hack" to my Pre-N Router, so it now thinks its a Linksys and is much more stable generally. If you try it, make sure you reset the Belkin to factory settings before applying the hacked Linksys firmware. Read the relevant forum entries carefully!
yeah. I did the linksys hack as well. I must say that I'm happy about that. it went really well. didn't need to do the factory reset and I only had issues with my dhcp range. but I fixed that.
still no love with the wizard though. do I need to set up a separate connection setting on my wizard? do I have to turn off the phone and the enable wifi? I also have the hack were I have gprs always on....could that be conflicting?
TIA.
The Wizard does seem to have more connecton problems than the Exec (I've had both) as its WiFi hardware is less advanced (based on an older SDIO design rather than fully integrated)
You should not need to turn the phone radio or GPRS off when connecting WiFi, though it might help troubleshooting if you do for establishing the initial connection.
I assume you are using WPA encryption? WEP is a royal pain on WM devices as you have to enter the full 26 character hex encryption key in the WiFi settings control panel- WM2003 and WM5 won't accept WEP passphrases.
If you are using WPA, I'd suggest removing the connection settings for your router on the Wizard, then turning WiFi on again and allowing it to try & connect. If that fails, you need to recheck your network settings.
If you are still having problems, you might like to look at my answer to a simiar query on 4WinMobile Here which worked for that user.
Thanks NeilM. I do have the old school WEP. It IS a pain entering in the Hex string (grumble). I need to check to see if my networked-tivo's can handle WPA...
I will check your other post as well.
Read through your other post. I think it was a "dumb" thing that I did. I changed the "connect to" item on the wireless card from "The Internet" to "Work" and it picked up an IP immediately. Duh...that would make sense if both my GRPS connection and my wifi were going to "the internet"...and thus conflicting, right?
My knowledge of Networking protocols etc is sadly lacking, so I don't know the answer to why this is how things need to be! I suspect all the network cards need to be connected to "Work" because the device has no direct link to "The Internet", and once connected via "Work", the TCP/IP settings take over and route packet calls to "The Internet" via the IP address settings.
Most important thing is that you are now connected!
Hope you can find time to visit 4WinMobile more often now you've found it. It's not intended to be as technically upfront as XDA-Devs, but is a very good inter-personal site with a great spirit, and some pretty good insider knowledge
Belkin pre-n
My MDA Vario would not connect with the original Rom. I was hoping this ROM update (CUSTOM_RUU_Prodigy_2170702_217_20710_TMO_US.exe) found here forum.xda-developers.com/viewtopic.php?t=44631&highlight=mda+vario would allow it to connect but it will still not. I used registry wizard to update the registry settings for Wifi G, but it still will not connect successfully. It seems some roms will work with the Belkin Pre-n. Does any one know which specific rom works with this particular router.
I'm getting desperate here- I can't get my MDA to connect to my Belkin Pre-N. Nothing works. I've got the latest firmware on the router, and I've enabled the "G" hack on the phone.
Anyone have any ideas? I've tried removing all encryption and security and still nothing. I can easily connect to my old Dell TruMobile router, but I don't want to use it because the range is so poor.
Is there anyway to ensure 100% that I've enabled the G hack?
Belkin Pre-n
I finally have my Belkin Pre-n (or linksys SRX clone now) working with my MDA Vario. It would not work with any Belkin firmware or variety of settings, but since its harware is the same as the Linksys SRX you are able to flash the unit to a Linksys clone. As a Linksys clone the Mda Vario connects flawlessly with no trouble. The first Belkin Pre-n I flashed to a linksys bricked the router, so be careful with this. To successfully reflash you must have a version 1 Belkin pre-n not v2 a hex edited version of linksys firmware found here http://www.streamload.com/Nodes/Node.asp?cxInstID=86340166&nodeID=672194467
IMPORTANT Have the Belkin pre-flash set to the default linksys IP 192.168.1.1, the default password 'admin', and the dhcp server turned off. These are the default settings for the linksys firmware and and if they are pre -set result in a easy flash. If these settings are not followed pre-flash you stand to brick your router, or have a difficult time ressurecting it. You must manually assign your computer an IP within the 192.168.1.1 -255 feild as you will have dhcp turned off. at the fierst login dont be alarmed it will not work. Restart your browser and type 'admin' in the username as well as in the password field. Now you can upgrade your router to the newest linksys firmware 1.02.10_USA found on the linksys website. Congratulations you now will enjoy flawless wifi on your linksys flashed Belkin pre-n.
Wizard with Belkin pre-N wifi router
I had the same problem. Turned off QoS and it connects without any problem. Try it.
Hi, maybe someone could be of any help
I tried out allready a lot and do not see a light at the end of the tunnel.
I am trying to get a TyTn to connect to CISCO APs using WPA with LEAP or PEAP or WPA-PSK and i do not manage to get it connected. The TyTn "sees" the network (SSID is hidden), tries to connect but did not manage to get connected. I tried with allmost any ROM available here. At the moment i am using the I-Mate on:
ROM version: 1.20.305.3
ROM date: 07/21/06
Radio version: 1.07.03.10
Protocol version: 32.41.7010.02H
Any help would be appreciated
Same problem here w/the Cingular 8525 and Cisco AP
Been the Cingular 8525 the same as the HTC TyTN, and using Cisco AP's at work I'm experiencing the same problems here.
The Cisco AP log shows a failure on the TCP/IP handshake when my 8525 tries to authenticate. We're also using WPA-PSK. Cisco support analyzed the log and found no explanation on why it cannot complete the 3 way handshake.
I can use WPA-PSK in my home network with a D-LINK DI-524 w/o any problems.
The next test will be to try a Linksys/Cisco router and WPA-PSK at a friends place, also I will try WEP (just for testing) at work and if I can w/o any encryption on the Cisco AP that is giving me problems.
I'll also try contacting HTC Support.
Thanks to anyone that could help, I will post any results of my tests.
Cyberg
The Wizard doesn't seem to support AES. Maybe other HTC devices have the same problem. I've also had trouble with routers running in dual AES/TKIP mode. Try setting TKIP only.
WM5 does not support AES. WM6 supports!!!
Entering the following line in the Cisco AP Config fixed it for me:
dot11 wpa handshake timeout 1000
I too am having troubles with the tytn and cisco AP's.
Ive done some testing
Encryption: none works
Encryption: WEP64/128 works when entering code in HEX
Encryption: WPA-PSK (HEX KEY, 64 digits) works
Encryption: WPA-PSK (ascii, 8-63 digits) FAILS
I will try the dot11 wpa handshake timeout 1000 later today, hope it fixes it.
Also noticed that my Hermes won't connect to my parents router (SSID hidden, WPA-PSK of about 16 digits). Somewhat frustrating, but never mind. Router in question is a Thomson Speedtouch 5xx (can't remember exact model number).
Go into Wireless LAN & Power Mode & max it out to Best Performance.
Same problem here... with my Tytn and an old 3com OfficeConnect b.
No way to enable WEP encryption (authentification will always fail).
Working perfect now with data encryption disabled: connection security made by letting only authorized mac-address to connect.
This way is also more secure than WEP encryption, am I right?
I will try the dot11 wpa handshake timeout 1000 later today, hope it fixes it.
Click to expand...
Click to collapse
Go into Wireless LAN & Power Mode & max it out to Best Performance.
Click to expand...
Click to collapse
Neither of these fixed it.
Its like the Hermes will only accept 64bit Hex key, which is fine but one of my other devices will only accept upto 63bit Ascii key
I had issues with my Cisco 1100 AP's and read somewhere on Cisco's website that QoS must be disabled on the Radio interface to get WPA/WPA2 to work:
Code:
interface Dot11Radio0
no dot11 qos mode
It worked for me
Andy
ADB100: Tried your code, still not working
Ive gotten WPA to work but only when useing the full 64digit key in HEX,
I think the Tytn has troubles with using ascii in WPA.
I had the same problem as the starter of this topic with Linksys WAG200G router, just couldn't set up to connect with WPA, so I switched back to disabled security with restriced access on trusted MAC address, and now it works like a charm.
WPA-PSK
Works for me. I have a Linksys WRT54G, and an 1100 AP. Connects to either of them seamlessly.
Just to add some more info in case anyone else stumbles on this thread.. had very same issues with WM5 on stock Hermes (T-Mobile VarioII). Had to unprotect the netork and rely on MAC filtering
Installing WM6 using Black 2.5 (now on 3.0) sorted the problem immediately. It seems some routers expect certain things from the device when using encryption that WM5 can't always provide (AES has already been mentioned). Yet another god reason to upgrade to WM6
Router here is Philips SNB 5600.
Hi
I'm having a similar problem with my Orange M700 (HTC Prophet) and Netgear DG834G.
Anyone any great ideas???
Andy
In my nouse I have an WIFI network with WPA and WPA2. When I use encryption, even WEP, te connection is established but after a few seconds of data transfer, there is connection goes dead. I tested an open connection, a WEP 64, 128, WPA en WPA2 connection. All except the open unencrypted connection stop working after a few seconds. The Ameo keeps being connected to the accespoints, but there is no traffic anymore.
Has somebody else had this problem? I will try a hard reset to test it with a clean install.
Gerald
Hi there what make is your Access point? (is it a Belkin or Netgear possibly?)
Accespoints
I have a Zyxel 2602HW and a SMC2870W.
You've not got a 3G data session already established have you? I'm guessing its a WM5 'feature' rather than a specific Ameo fault, but if you're got 3G running, then connect to a Wireless Access Point, it gets itself all confused and tries to use the 3G connection for net access. I normally just quickly turn the phone service off and on, once the wifi service is running, via comm manager.
I've also noticed something else, where if I'm sending or receviing e-mail, and I'm already connected to the wifi point, it doesn't know to use the 3G connection rather than the wifi point to access the t-mobile servers. You have to close the wifi session before it is able to send/receive the messages (which don't always immediatly retry) but I'm guessing that maybe I could do something with routing on the Ameo. I need to get a grounding of the network stack on it before I can do it.
No, I tested it by putting it in flight mode and then enable wifi. When I do not use encryption, there is no problem. It works and I can watch ip televison. But when I use encryption, I cannot get a connection with whatever url within seconds. Only reconnect give me again a few seconds. It is frustrating. My MDA PRO and my DELL X30 do not have any problems at all.
QAN said:
No, I tested it by putting it in flight mode and then enable wifi. When I do not use encryption, there is no problem. It works and I can watch ip televison. But when I use encryption, I cannot get a connection with whatever url within seconds. Only reconnect give me again a few seconds. It is frustrating. My MDA PRO and my DELL X30 do not have any problems at all.
Click to expand...
Click to collapse
yeah i think it happended to me as well..i cannot get connected gor long...at always disconnected and connect again...
one more thing..my previous UNI it always auto detect..but not with dopod..
Compatibility
I found that the Athena is compatible with 3Com accesspoint but not with Zyxel or SMC. I use my neighboors 3Com and that worked. I decided to install my old 3Com Home Connect accesspoint and that one also worked. But the others do not. At this point it does not matter if I use encruption or not. Only the 3Com devices work. Does anybody hav another type of device that works?
Odyssey Access Client
I found this WPA/WPA2 client from Junipur http://download.juniper.net/software/aaa_802/public/oac/WM_Client_45/OdCeClientPPCSigned.ARMV4.CAB
If you have installed this install directly the following file and reset your device. ftp://xda:[email protected]/Uploads/Software/OdCl450CrOnlyFALLEN.cab
Now you will see that the Ameo will connect to the other accesspoints.
So you see there is a bug in the WIFI part of the radio rom!
No problem for me, i´m usung a netgear WG834GT for the moment.
Maybe my HTC X7500 Advantage has some other roms with the problems solved because it is swedish
Chill \Björn a.k.a Invalido
QAN said:
In my nouse I have an WIFI network with WPA and WPA2. When I use encryption, even WEP, te connection is established but after a few seconds of data transfer, there is connection goes dead. I tested an open connection, a WEP 64, 128, WPA en WPA2 connection. All except the open unencrypted connection stop working after a few seconds. The Ameo keeps being connected to the accespoints, but there is no traffic anymore.
Has somebody else had this problem? I will try a hard reset to test it with a clean install.
Gerald
Click to expand...
Click to collapse
I have no problem using the WIFI. I'm normally able to see about four if I'm at home. The other access points are my neighbours', some of which are secured while others are'nt. If I connect to any one of them they tend to drop off after a while due to week signals. Even if I use my own within the house, the signal is weak sometimes, in which case, the system automatically goes to UMTS connection which is far far faster in my case (Because my WIFI's bottlenect is from the slow ADSL speed of 512kbs download speed max, and my phone, running at UMTS, has higher speed.
So, check the signal strength and see if this is the cause.
Since my works all the time, may be by showing you my wifi configuation for comparison might help.
I'm using WEP data encription. The network key is entered on start>setting>connection>Wi-Fi. I would see all the hot spots there. After I selected my own WIFI, I select connecting to the internet and press NEXT. In the next screen I chose Open WEP and untick automatic box. I then enter the network key which I obtain from my router administration screen on my PC.
That's it. I hope you have your problem resolved soon
Thanks for the info, but this is not my problem. I can connect to whatever accespoint. Only my neighbours accespoint makes it possible to connect to te internet. When I connect to my own network my ZYXEL is giving me troubles because it is blocking traffic after 10 seconds. It doesnot matter if connect to it by WIFI or using my SMC bridge that is connected bij LAN. It doesnot matter if I use encryption or not. Strange enough when I use Odyssey Access Client I can connect to the internet. I have to say that this is not always the case. The signal in my home is more than 80% for both WIFI gateways. Every other device I use, an MDA PRO and a DELL X30, do not have troubles when they want to connect to the internet. So I conclude that the WIFI on my Ameo is not completely compliant. This could be my device, te rom or my gateways. I do not think my gateways are the problem. Both are from different manufacturers.
Seems to me that I have a similar problem...
I got my Ameo yesterday and installed W-Lan. I'm using WAP encription. I get a very weak signal and have a very slow Internet connection (like in the "good-old 54k modem days" ;-). Sometimes there is even no response from the internet. Then I have to close W-Lan in the connection manager and to restart W-Lan again.
Dieter
That is exactly my problem. It works at the beginning but after a few seconds it looks like the Ameo is in quicksand. There is no information from the internet anymore that reaches the Opera browser. I tried Odessey Access Client with better results, but it does not work all the time.
@dieterpapa
What type of accespoint do you have?
i´m using a linksys wrtg router + an additional linksys range expander to cover my house completely.
what i´ve seen, too is that using the ameo about 3 mtrs to the expander i only get minimum w-lan signal.
do we perhaps have a problem with the antenna ?
@qan: how is your signal strength?
dieter
I have the same problem. gets connected no problem. I can download files from my pc. But leave it a few seconds to look at a web page then the connection drops I have to reconnect at com manager. never happend with my mda.
QAN said:
Now you will see that the Ameo will connect to the other accesspoints.
Click to expand...
Click to collapse
I had the same problems while connecting the Ameo to a Freebox (special router for French DSL offering, http://adsl.free.fr/wifi/).
After installing the programmes you listed (and restarting several times) I could connect with the new WiFi tool. Now sometimes I have problems when the programme thinks WiFi is disabled but in fact it is not, but this is only temporary.
Thanks!
Found Problem!!!!!!!!!!!!!
I have finaly found the problem. I am sure the problem is within the rom of the Ameo. The problem is caused by the auto scaling feature of the processor. When the WIFI connects to an encrypted accesspoint the WIFI connection is not setup correctly. To prove this I have installed Pocket Hack Master and disabled the build-in scaling. After this my Ameo connect without any problem to the accesspoint and internet. This works with every processor frequency from 104Mhz up to 728Mhz. Yes at 728Mhz the Ameo is blazing fast. You won't recognize your device. Also after activating the scaling feature of PHM it still works. After disabeling PHM the connection went dead again.
You have to deactivate the build-in scaling before you activate the WIFI connection.
Lets hope someone can patch the rom or that this problem is not available within WM6.
Gerald
And how to disable internal scaling ?
Dieter
dieterpapa said:
And how to disable internal scaling ?
Dieter
Click to expand...
Click to collapse
it's in the setting, disable internal scale
Thanks - found it in the hack master setting.
However my Ameo doesn't pass 728MHz - it hangs. Maximum is 663 MHz.
Dieter
Hi All,
I too have a strange WiFi issue. Here goes:
My phone is able to connect to free WiFi stations and the WiFi station at my parent's place. When I try to connect at home, it connects but I am unable to browse.
I previously used WEP encryption and have also tried removing all encryption...but no luck.
Here are my current router settings:
Band 2.4 GHz B+G
Mode AP
Channel 9
Authentication Open
Preamble type Long
Broadcast SSID Disable
Encryption None
Use 802.1x Authentication Disabled
Phone Details
HTC Touch
Browser Netfront/IE
My laptops, DS Lite, Wii can connect and work with the router...
Any help will be highly appreciated
Check that you don't have MAC ADDRESS FILTERING at the router. It may be hidden under Filter settings, like my D-Link is. This may sound trivial, but more than once I forgot about the MAC filtering.
If that doesn't help you, then just to narrow it down, at my home I use WEP and disable SSID broadcast also, and my Touch can connect fine, and fast.
Scratch the last post! I had the same problem with my TOUCH..Just put the power level to the max (i.e. go Start -> Settings -> Connections -> Wireless LAN -> Power Mode -> and slide all the way LEFT to Best Performance) and all hail ..your problem solved
I also use a Touch. I put the slider all the way to the right (Best Battery) and I connect fine. You people must have a big house, or a crap router?
HTC Touch wireless lan connection problems
hi,
Im having the same problem. No MAC filtering & no encryption on ADSL router.
HTC touch can connect to the router at 192.168.1.1. But it does not connect to any other web page.
Message shown is: "Page cannot be found. Check the name and try again."
Any other tips.
Thanks in advance.
dbmayur said:
Hi All,
I too have a strange WiFi issue. Here goes:
My phone is able to connect to free WiFi stations and the WiFi station at my parent's place. When I try to connect at home, it connects but I am unable to browse.
I previously used WEP encryption and have also tried removing all encryption...but no luck.
Here are my current router settings:
Band 2.4 GHz B+G
Mode AP
Channel 9
Authentication Open
Preamble type Long
Broadcast SSID Disable
Encryption None
Use 802.1x Authentication Disabled
Phone Details
HTC Touch
Browser Netfront/IE
My laptops, DS Lite, Wii can connect and work with the router...
Any help will be highly appreciated
Click to expand...
Click to collapse
hencre said:
hi,
Im having the same problem. No MAC filtering & no encryption on ADSL router.
HTC touch can connect to the router at 192.168.1.1. But it does not connect to any other web page.
Message shown is: "Page cannot be found. Check the name and try again."
Any other tips.
Thanks in advance.
Click to expand...
Click to collapse
Same problem I am having now. I can connect now wifi, but get same error.
??????
Wifi Problem!
Hi guys,
I've got a problem and I'm hoping you can help me out..
I've got a HTC TOUCH and when I got it the Wifi connection was working just fine.. I could connect to any WIFI network and Browse the internet.
After a month or two, my phone wouldn't connect to my home wifi network anymore. And neither would it connect to any other wifi networks (I tried!)..
I've been all over the internet trying to figure out what could have happened and if someone else was having these problems to.
I just can't find the answer and I feel like I already tried everything I could think of..
Hope some of you knows what to do..
I'd suggest looking at the Touch forum... I've got no experience of Touch devices, but it may be a Radio ROM issue...
kinda same issue I am facing ! donno
MY HTC TOUCH never connects to NETGEAR WIRELESS ACCESS POINT
but finds LINKSYS routers in a jiffy :O
are Wireless Access Point and.. Wireless routers different
they both emit diff. signals ?
I have the same issue with a TYTN II, can connect to the wireless, but can't open any web pages.
problem with htc & WPA-PSK passkey 25 characters
My htc tilt connects almost everywhere, but i have a problem with wpa-psk at work. The password is from 25 characters, I read some articles what WM cannot handle such length. Maybe it's possible to edit somehow the registry?
I have the same problem guys, what can we do to find a solution i tried everthing i could, and i even tested it out with my 2 wireless routers, and at public places it connects (at home it doesnt connect though).
shirreer said:
Scratch the last post! I had the same problem with my TOUCH..Just put the power level to the max (i.e. go Start -> Settings -> Connections -> Wireless LAN -> Power Mode -> and slide all the way LEFT to Best Performance) and all hail ..your problem solved
Click to expand...
Click to collapse
Thanks a lot!
I had exactly the topic problem with manilla rom on my kaiser, could not use wifi any more. But with just sliding the meter to 'Best Performance' as suggested, wifi it once again works like a charm.
HTC Touch wifi solve
I had the same problem with my htc in WEP it dosen't browse, I changed the router to a better wifi protection like WPA-PSK, connected and worked fine, for some reason it only work's fine for a couple of minutes, I readed this post to put the sidebar in best performance and now everything works fine. An advice don't use WEP it's not secure at all.
http://en.wikipedia.org/wiki/Wireless_security maybe you fine this interesting and helpful.
I'm running into a problem were I can connect to an AP at work and surf the net fine but when I disassociate I cant connect to it again for a whole day. The AP must be saving some info and therefore will wait for the DHCP lease time to finish before allowing the touch to re-connect. I tried my laptop and was able to connect 3-4 times and never have a problem so it is isolated to the touch and windows mobile 6.1. To find some more info out I was able to clone the mac of the touch and use it as the laptops wifi cards mac. It connected fine on 3 consecutive tries.
Maybe windows mobile is missing some commands when disassociating from an AP and as a result leaving info out in nowhere land confusing the router.
Thanks for any help!
ok, here's me joining the club... dunno what happened... working one day, getting crap the next.
exact same problem as everyone else...connects to the wireless network, then when you try to surf, page cannot be found...
Exact same problem here.
In the beginning everything fine. Connecting to my home WiFi and using the internet without problems (weather, stocks, opera, email, google maps, even skype voip).
Then, last month, all programs are unable to find anything on the internet, although the device reports it is connected to my (unchanged) home WiFi.
All these programs work fine when the device is connected to the internet through activesync (usb cable).
Also this whole time I have been using my home WiFi with a laptop from both Vista and Ubuntu, with no problems, so I guess it's not the router.
Also have read in other fora about these wifi working - wifi not working "cycles" other people have had, with various WM devices. And various tricks like shutting wifi off and immediately on again.
I even hard reseted the device. Problem still there.
WTF?
Connected once only
Connected once only for a few minutes to my home router dir 310 D-Link, worked fine and fast. After that I closed the connection. Next day I tried to connect but my HTC Touch 3G doesn't see the router. I see any other routers, but I do not see mine. I connected to some friends routers with WEP and WPA encription just to be sure the phone working. During this I didn't changed the router or the phone settings. It is very strange. The problem maybe comes from the router.
I'm having the same issues with my HD2. Looking all over the place and seems to be a common fault, but thus far with no cure, I tried the power save mode
From new it worked like a dream, but then one day it would connect to AP's but act as if not connected. I flashed my ROM with the VERY impressive Merlion Leo v 2.66 and it all started working again. Then yesterday, it stopped again. I don't want to reflash, so I'm working hard to find a cure, and will report as soon as I find one.
---EDIT---
I've found a cure (for mine at least), not sure if it will work for everyone, and haven't managed to test it at any other AP's except for my home Router, but all I did was set the network card properties (Broadcom 802.11 DHD Network Adapter) to 'Use server-assigned IP address' instead of 'Use specific IP address'. I'm not sure why this worked as there was no IP address conflicts because there were no other devices connected to my router when I had problems, but it works for me, hopefully permanently
Good luck.
Try this. Its work perfect for me!
http://forum.xda-developers.com/showpost.php?p=10035476&postcount=10
Hi guys.
Im an Asus p535 owner and since i bought it im having some problems with wifi. I use this setting at home and everything works fine:
Authentication : Shared
Date encription: WEP
and then i put my PW.
NO IP and no DNS. all in blank (To use DHCP)
The router assigns an IP to my pda (DHCP server).
But when i wish to connect to a FREE AP i cant,my friend with his N95 has no problems to log into them everything goes auto for him, when i go to his house and I try to log int his wireless network settin the right key i also cant. i have tried, the problem is that according with my PDA the AP doest asisgn an IP to my PDA, it looks like my home settings are brozen and the PDA tries to find the gateway in the same IP when i check the stupod asus P535 wifi manager there is no way to make disapear my home gateway and DNS. i tried with renew setting wifimanager OPEN and NO KEY, chaging default channel, but there is no way i have even upgraded my ROM to unofficial 6.1. If i set a random IP manually it connects but ofc inet doest work since the gateway used is not right. thx to this web wich at least runs faster than the previous one... sry for my bad english. and ty for all. Sry if this post is and old issue i did my best lookin for Asus P535 wifi problems and WM 6 wifi problems but didnt get nothing... all i got was that the new ROM said WIFI fixed... but no for me ><.
Asus P535 Wifi does not working even with Wifi fixed ROM Solved!
If your ASUS P535 WiFi does not work under WM6 (even with ROMs that has WiFi fix):
- The turn on WiFi option is grayed out (not available)
- The WiFi is on, but you cannot connect, jumps back to available status, after connecting to network..
Download the 4.70 radio firmware, copy to MiniSD card, connect USB or AC power, start FW setup on PDA simply by clicking on it to upgrade, soft-reset after completed.
http://www.asusp535.com/download/firmware/radio/P535-FW-V470.rar
Test WiFi connection, and if it still does not work, use those reg files attached in wifi_regsetup.zip on PDA, and press yes when it asks for confirmation.
Soft reset when complete.
With this fix I was able to connect anything but WPA2-AES network, it was a long connection attempt, over 4 min.
Tested with PDAViet_WM6.1_19900 ROM:
http://www.asusp535.com/download/firmware/unofficial/PDAViet_WM6.1_19900.rar
I suck with this WiFi problem for 4 days, now i can sleep at last...
Bye!
Xel