I have a new Wizard (O2 XDA Mini S) which refuses to connect to my Belkin Pre-N router.
Despite trying all I can think of, including Encrypt On/Off; WEP, WPA; b/g mixed access; changing Channel and SSID, reset to defaults etc, etc I still get no joy.
I even suspected a hardware fault with the Mini, so had it changed, but the new one is the same.
When I start WiFi, the Mini finds the Router, and requests the WPA key. Once supplied, it just goes back to "Available" in the list of connections; forcing a "connect" shows it trying to connect, but it just returs to "Availabe" again. The network properties shows no connection (no SSID or Channel) and no signal strength.
All my other WiFi clients connect fine- O2 XDA Exec, Toshiba Laptop and another PC client. Even my old Ipaq with jacket connects, so its not a b/g problem.
I've even tried using the 802.11g registry hack cited in another thread to no avail.
The Mini did connect to a BT Openzone Access point this morning, so the capability is there.
Connection settings for the connection are for "The Internet" and the overall network card settings (above the Network adapter list) to "Work", though I did try this with "The Internet" out of frustration.
Any ideas guys?
Neil
I have had the same problem. As soon as I put the hack in I cant connect.
Take the hack off and it connects. Belkin pren adsl router
dalewinterstein said:
I have had the same problem. As soon as I put the hack in I cant connect.
Take the hack off and it connects. Belkin pren adsl router
Click to expand...
Click to collapse
Thanks for the advice, but I tried it without the hack first- no go, and have now done a hard reset (I've done so many hard resets I've lost count!)
Everything I try fails. Just about to try the firmware update for the Router.
Sorted- the router firmware update fixed it!
NeilM said:
Sorted- the router firmware update fixed it!
Click to expand...
Click to collapse
So you are saying that the router was the one causing the issues, you think, and not the Wizard (MDA)? I have the same issue. Have the hack (g) installed. I was only able to connect once to the my Belkin pre-n...but for some reason cannot get an IP address...ever...
I think it was a combination of the 2 things:
The G HAck on its own did not work, and the firmware update on its own didn't work, but updating the firmware, and using the G hack allowed my Wizard (O2 Mini S ) to connect and it has been fine since.
In fact I've now applied the "Linksys Hack" to my Pre-N Router, so it now thinks its a Linksys and is much more stable generally. If you try it, make sure you reset the Belkin to factory settings before applying the hacked Linksys firmware. Read the relevant forum entries carefully!
yeah. I did the linksys hack as well. I must say that I'm happy about that. it went really well. didn't need to do the factory reset and I only had issues with my dhcp range. but I fixed that.
still no love with the wizard though. do I need to set up a separate connection setting on my wizard? do I have to turn off the phone and the enable wifi? I also have the hack were I have gprs always on....could that be conflicting?
TIA.
The Wizard does seem to have more connecton problems than the Exec (I've had both) as its WiFi hardware is less advanced (based on an older SDIO design rather than fully integrated)
You should not need to turn the phone radio or GPRS off when connecting WiFi, though it might help troubleshooting if you do for establishing the initial connection.
I assume you are using WPA encryption? WEP is a royal pain on WM devices as you have to enter the full 26 character hex encryption key in the WiFi settings control panel- WM2003 and WM5 won't accept WEP passphrases.
If you are using WPA, I'd suggest removing the connection settings for your router on the Wizard, then turning WiFi on again and allowing it to try & connect. If that fails, you need to recheck your network settings.
If you are still having problems, you might like to look at my answer to a simiar query on 4WinMobile Here which worked for that user.
Thanks NeilM. I do have the old school WEP. It IS a pain entering in the Hex string (grumble). I need to check to see if my networked-tivo's can handle WPA...
I will check your other post as well.
Read through your other post. I think it was a "dumb" thing that I did. I changed the "connect to" item on the wireless card from "The Internet" to "Work" and it picked up an IP immediately. Duh...that would make sense if both my GRPS connection and my wifi were going to "the internet"...and thus conflicting, right?
My knowledge of Networking protocols etc is sadly lacking, so I don't know the answer to why this is how things need to be! I suspect all the network cards need to be connected to "Work" because the device has no direct link to "The Internet", and once connected via "Work", the TCP/IP settings take over and route packet calls to "The Internet" via the IP address settings.
Most important thing is that you are now connected!
Hope you can find time to visit 4WinMobile more often now you've found it. It's not intended to be as technically upfront as XDA-Devs, but is a very good inter-personal site with a great spirit, and some pretty good insider knowledge
Belkin pre-n
My MDA Vario would not connect with the original Rom. I was hoping this ROM update (CUSTOM_RUU_Prodigy_2170702_217_20710_TMO_US.exe) found here forum.xda-developers.com/viewtopic.php?t=44631&highlight=mda+vario would allow it to connect but it will still not. I used registry wizard to update the registry settings for Wifi G, but it still will not connect successfully. It seems some roms will work with the Belkin Pre-n. Does any one know which specific rom works with this particular router.
I'm getting desperate here- I can't get my MDA to connect to my Belkin Pre-N. Nothing works. I've got the latest firmware on the router, and I've enabled the "G" hack on the phone.
Anyone have any ideas? I've tried removing all encryption and security and still nothing. I can easily connect to my old Dell TruMobile router, but I don't want to use it because the range is so poor.
Is there anyway to ensure 100% that I've enabled the G hack?
Belkin Pre-n
I finally have my Belkin Pre-n (or linksys SRX clone now) working with my MDA Vario. It would not work with any Belkin firmware or variety of settings, but since its harware is the same as the Linksys SRX you are able to flash the unit to a Linksys clone. As a Linksys clone the Mda Vario connects flawlessly with no trouble. The first Belkin Pre-n I flashed to a linksys bricked the router, so be careful with this. To successfully reflash you must have a version 1 Belkin pre-n not v2 a hex edited version of linksys firmware found here http://www.streamload.com/Nodes/Node.asp?cxInstID=86340166&nodeID=672194467
IMPORTANT Have the Belkin pre-flash set to the default linksys IP 192.168.1.1, the default password 'admin', and the dhcp server turned off. These are the default settings for the linksys firmware and and if they are pre -set result in a easy flash. If these settings are not followed pre-flash you stand to brick your router, or have a difficult time ressurecting it. You must manually assign your computer an IP within the 192.168.1.1 -255 feild as you will have dhcp turned off. at the fierst login dont be alarmed it will not work. Restart your browser and type 'admin' in the username as well as in the password field. Now you can upgrade your router to the newest linksys firmware 1.02.10_USA found on the linksys website. Congratulations you now will enjoy flawless wifi on your linksys flashed Belkin pre-n.
Wizard with Belkin pre-N wifi router
I had the same problem. Turned off QoS and it connects without any problem. Try it.
Related
Im looking to get the Wifi working on my Vario at home. My current Access point wont connect due to T-mobile's lock out of the 802.11g.
So I can get a Access point that works, I thought it would be helpful to post up your Model with a Yes or No after you have tried all the different settings as posted on the forum e.g. different channels and mixed mode etc.
This is for g Locked Varios only please not ones with flashed ROMs.
Please keep it simple Model YES or NO.
Thanks
:wink:
To Start us off......
Inexq HR054g Access point (NO)
if your Wizard has b only (ROM issue, not hardware) then ANY router which is set to allow g only will fail to connect. yours "should" allow "b" devices to connect http://www.inexq.com/web1/images/product/spec/hr054g.htm
So maybe you have a setting that is allowing "g" only
Beeble said:
if your Wizard has b only (ROM issue, not hardware) then ANY router which is set to allow g only will fail to connect. yours "should" allow "b" devices to connect http://www.inexq.com/web1/images/product/spec/hr054g.htm
So maybe you have a setting that is allowing "g" only
Click to expand...
Click to collapse
Router is set to mixed mode, it can see the network but wont connect
Have you got MAC address filtering enabled on your router and forgotten....I did.
Also try changing WLan card settings on your XDA from Best battery to best performance..Make a lot of difference. and many have found theirs connects after this
All turned off any other options
I have a BT2100 wireless router and mini-s, sometimes it won't connect until I stop active sync running on the mini-s ???
3-Com OfficeConnect ADSL Firewall Wireless 11g Router (set to mixed)
Vario will only connect when router set to open access i.e. security disabled. Any other setting i.e. WAP, WEP causes the routers internal DHCP server to fail to send an IP address back to the Vario... or the Vario being unable to acknowledge the router?
Have got a couple more routers comming my way, will post them up when Ive had a chance to test them
devasoftware said:
3-Com OfficeConnect ADSL Firewall Wireless 11g Router (set to mixed)
Vario will only connect when router set to open access i.e. security disabled. Any other setting i.e. WAP, WEP causes the routers internal DHCP server to fail to send an IP address back to the Vario... or the Vario being unable to acknowledge the router?
Click to expand...
Click to collapse
I've seen this issue detailed elsewhere but I can't remember exactly where - apparently for some reason the 3com sends back an IP v6 address when security is enabled, which the Wizard can't use.
So far I've used a cheapie Origo wireless router (conexant chipset) and a Netgear D834G (in mixed mode), my Wizard seems happy with both.
John
Pardon me because this isn't entirely a Wizard specific questions although I am able to replicate the problem with my Cingular 8125 (new ROM) 100% of the time.
I'm not a stupid person. I've setup numerous wireless networks for corporations and home users. I always use WEP or WPA and never unencrypted (no) security.
In most situations, the wireless router does NOT supply the DHCP to the clients. It usually comes from another DHCP server on the same LAN segment. Typically, this is a Windows server although it could be a DHCP-assigning device, such as a Cisco router.
PCs have no trouble seeing the wireless network and connecting to it and getting addresses assigned to them. For a while, I couldn't do this on WPA security but upgrading firmware and software on the laptops (usually Dell) rectified this.
With my Wizard, both old and new ROMs, I can SEE the wireless networks and connect to them but I can NEVER get an IP address. It tries and tries and fails and fails and eventually gives up. (Yes, the Cingular proxy is turned off)
Yet, at the airport or other public places with free wireless, I have no problems connecting my Wizard to the access point and surfing away. Thus, I know its not (entirely) a Wizard issue. Of course, these public access points aren't encrypted which could be one of the reasons but I doubt its the only one.
As a test, I just built a new wireless router with a SSID (other than "default") and security turned on (WPA) and let the router act as the DHCP server. Wizard connected in seconds and was surfing away. So the obvious next question is: why doesn't this work when the wireless router ISN'T the DHCP server? Other machines (laptops and such) have no problem connecting to one wireless router and getting a DHCP address from another box yet my Wizard cannot.
I've tested this with D-Link and Belkin wireless routers (consumer-grade).
I've seen other people post that they cannot get their wireless to work on their Wizard and while the fix may not be on the side of the Wizard, I think others may be in the same boat I'm in so I'm hoping that maybe we can compare enough stories to narrow this down so that we CAN use our Wizards wirelessly!
Ken
Confusing...
maybe you should try assign a fix ip to your pocket's wifi adapter and see if it would work. or just let the wlan security turn OFF on your access point to see what would happen.
i guess that the network protocol stack is slightly different between a PC and a PPC, which limit the DHCP request route.
I have just purchased the Wizard, aka o2 XDA Mini S, and use it with my Belkin Wireless Access Point (WPA-TKIP Enabled, DHCP & NAT disabled) and Cisco ADSL Router (DHCP Server) without any problems.
I have assigned the Belkin Wireless Access Point a fixed IP address however, but I don't think this would make a difference.
The other thing I found was that the Wizard would not connect correctly to the Belkin using WPA with AES encryption, but switching it to WPA with TKIP works flawlessly.
Well, I suppose its encouraging that others with the same wi-fi routers are getting this to work but its discouraging that I'm having so much trouble!
Fixed IP does work (therefore, its unlikely a Wizard-only problem) but obviously a fixed IP doesn't let me roam from one hotspot (home) to another (work) very easily.
Haven't tried it sans-security yet although that might just prove a point, rather than be a perminant solution. I have tried WPA-PSK and WEP with the same (negative) results.
I personally have found that unless I change the power settings for the WiFi adapter to full power, its hit or miss.
Never have a problem maing connections, geting leases, etc with it there.
YMMV though
Regards - John
prob irrelevent
i found that before i active sync'd. the wireless monitor on my wizard showed a strong signal from the router. then after it synced, it picked up an IP from the servers dhcp fine.
also for lightweight simple security i use mac address filtering on the AP
Hi!
I do have problem to connect the device (o2 xda mini S) to WLAN. It recognizes the network, asks for the WPA-PSK key and then attempts to connect - but fails.
If I configure the device with a static IP this IP shows up during the
connection process after a while but the device isn't connected anyway.
If I use DHCP I get no IP ever.
I also tried a very simple 8 alphanum character key.
What may be wrong here?
I hope you get an answer soon, because I have the same problem. Enter the key, then no connect. I also tried it with security turned off on the router, no connect. This thing connected every time before 2.26 ROM update.
bump - having the same issue
bump
Hope there's a reply; having the same issue but I think it's router specific too. I am on Dlink DI-614+ and a friend of mine who has DI-524 (i think) has no problem connecting reconnecting.
if you figure out a way to get it to work, please PM me... I have not figured out this problem yet.
I might try to disable all of my router settings (WEP).. but that would only mess my already configured other devices up.
Stupid question, but is it a B/G router or is it configured to only do one of them ?
Well, I got it to work by disabling encryption and leaving the AP all open...
So, apparently the software has some WPA-PSK-related bugs
Same thing with 2.24a Mr.Clean. Open AP works fine, and any encryption messes the whole thing up. The connection is done, it even gets the IP - and continues to blink arrows and no data comes through.
Windows Mobile only knows TKIP but as I was using AES and wanted to continue using AES on the other machines I configured the router to provide "TKIP and AES". Well, this didn't work but TKIP only actually works now.
I've been having the same problems, could connect to unsecured networks, no problems. The thing would just refuse to connect to my home WLAN (Belkin 54G set to B/G), secured with WPA-PSK and TKIP data encryption. However, just updated the router's firmware from the Belkin website, and BINGO!!!! It found the router, I entered the key and immediately connected, fast too. Just try updating the firmware of your router!
I agree on the router upgrades. And some routers are just crap, sorry to say. I've had bad luck with Belkins and Netgears. Linksys and D-Link typically give me much less problems. You also need to make sure that you installed the registry settings to enable G networks on you device (of course)
I have a Sonicwall using WPA-PSK with no problems.
I personally like molski's tweaks to make the necessary registry settings on my device ... http://forum.xda-developers.com/viewtopic.php?t=58438
Hope I was of some help.
Has anyone tried to use their TyTN with a WRT54G Router. I can get it connected to the wireless signal and it has a DHCP IP but I cant seem to get it to automatically pickup the DNS servers. I an connected to the WAN via PPPoE. The connection is 100Mbit FTTH. The PCs wired to the network can get on the net just not the TyTN on the wireless signal.
Any help is appreciated.
Nevermind
Put the DD-WRT custom firmware on there then set the DNS servers manually and its blazing.
Hermes (Dopod 838 Pro) and the WRT54G Router Issue
I have the same problesm! I run a WRT54G router AP at home and created a MAC list that enables access. Of course I updated the MAC list filter on AP. I get to connect my JasJar, but no such luck with the TyTN. Then I hooked an ASUS portable access point to one of the routers cable slots and my TyTn connect seemlessly!
I read the DNS suggestion and alos trying to run the AP woth fixed IP! I would then have to do that for all systems that access the Routre, right! Isn`t there a way to make th 54G work with DHCP and assign IP addressess dinamicly to the TyTN, as it does to any other WiFi equiped device?
Try this;
Check what type of wireless encryption you are using. If you are using AES then create another SSID or change the current SSID to use TKIP for your TyTN to connect to. I don;'t think the TyTN supports AES.
Later, Lew
ooops
oops, ignore my reply. Clicked on the wrong button and accidently replied here
you can always do this... sell your linksucks on ebay or to a friend then go buy a better router i have seen many issues with linksucks and HTC devices, there was tons of weird issues with the wrt54g and the wizard
Mine works without issue. I do have the sveasoft firmware loaded though. I also don't use pppoe.
Load the DD-WRT and it's very stable..
I have a DLINK 604T and it work with no issues with dynamic IP/DNS. This router is also cheap as compared to lynksys
WRT54G working FINE with Hermes 100
Hi Everyone!
If you own a WRT54G router/access point and were experiencing trouble to connect your Hermes 100 to it, sweat no more! Go www.linksys.com, select downloads and choose from the long list of routers. Make sure you match the model number and the version number of your router. Download the FIRMWARE upgrade. I was running the original firmware from my router a WRT54G V1.1. After upgrading the firmware, my router worked great and the range was almost 4 times what I had before!
Check it out!
Cheers
Michael
Dopod 838Pro
Was a bit worried as read this before my Vario II arrived and I have a WRT54G...
Connected fine 1st time... just added MAC to filter and put key into vario. bingo-bango!!
FYI I have WRT54G Firmware Version: v1.42.2 (the firmware I bought it with)
Hi all
Ive just brough a new belkin wireless n router set it up as you should connected my laptop my brothers laptop my desktop my ipod touch but my MDA touch will not connect to it. My touch connects to my other trendnet router fine and all other AP i have tryed. what is really bugging me is that when i try and connect to my new belkin it wont let me connect to any other routers so i have to delete the belkin router from my device and soft reset
i am starting to think it could be a faulty router or mda
Same boat....
I have the same issue with my HTC Kaiser, can see a host of AP/Wireless Routers via the Wi-Fi card but fails to connect to my Belkin F5D8631-4 v3 N1 Wireless Modem Router, a real pain in the arse considering the price I paid for the router, everything else connects, PC's, PS3, 360, DS Lite, PSP the lot....all bar the Kaiser.
Anyone managed to find a solution to this issue and sitting on it
Before you ask, no security enabled, only using the MAC address filtering to do the job of keeping unwanted off my network, even with this turned off the Kaiser see the network, flags it up as available but will not connect....
Any help gratefully received
Connecting
I bought a sitecom mimo XR router, I have got the same problem with a Qtek 9090.
The solution I found is, dont activate dhcp on your device but manually add the ip adresses of your router and device, set the dns server ip-adress to the ip-adress of your device.
Worked for me.
royaldutch51 said:
I bought a sitecom mimo XR router, I have got the same problem with a Qtek 9090.
The solution I found is, dont activate dhcp on your device but manually add the ip adresses of your router and device, set the dns server ip-adress to the ip-adress of your device.
Worked for me.
Click to expand...
Click to collapse
Thanks for the feedback/comments
I have done (I think) correctly and its still not playing ball, just to confirm the actual detail:
Router Set Up:
DHCP Activated ? (it is currently)
All WEP/WPA turned off
MAC address filtering turned on and the MAC adress for the hand set network card (found by
on to Com Manager, Settings, Wireless Lan, Advanced Tab) is on the list on accepted MAC address on the MAC filter
Handset Settings
Wireless Network Adapter settings (on Configure Network Adapters page)
IEEE 802.11b/g Compatible Wi-Fi
User Specific IP address 192.168.2.50 (not an address allocated by DHCP)
Subnet Mask 255.255.255.0
Default Gateway 192.168.2.1 (IP address of the Router)
Primary DNS 192.168.2.1 (IP address of the Router)
I get the same sort of problem occasionaly with my universal. The only thing that sorts it out is deleting any reference to the connection then removing the battery. This seems to flush out the system & then it finds it a new connection & connects straight away, worth a try if nothing else works.
JohnWB said:
I get the same sort of problem occasionaly with my universal. The only thing that sorts it out is deleting any reference to the connection then removing the battery. This seems to flush out the system & then it finds it a new connection & connects straight away, worth a try if nothing else works.
Click to expand...
Click to collapse
Thanks John,
I did try this, and it didn't make a difference.
You know when you get that feeling you are going to have to admit defeat....
Any solutions so far
Guys,
Does anyone has a solution so far?
What version of Windows mobile are you running?
This post in the Shift forum
http://forum.xda-developers.com/showthread.php?t=384730
mentions a beta firmware on Belkins UK site which solves the problem.
hi, i'm using a mda vario 3 with an older Belkin router and it works fine. I have the dhcp server turned off with all the ip's set manually. the ieee 802.1 auth thingy is not selected. other than that my settings are similar to those posted above. Although i have wep security set up. (Nintendo ds's only do wep)
Corrykid said:
What version of Windows mobile are you running?
Click to expand...
Click to collapse
I run Windows Mobile 6.1
When I ran Windows Mobile 6.0, I did not have contact with my Sitecom WL-173 router either.
tembares said:
Guys,
Does anyone has a solution so far?
Click to expand...
Click to collapse
I have found the solution.
Just upgrade the radio to 1.64.08.21.
Then it works.
wifi problem
just upgraded my MDA to wm6.1 and i encountered a problem regarding with my wifi connection.
having my old wm5, i dont have any problem connecting to my wireless router(d link) but when i upgraded my wizard to wm6.1, at first it will connect for about 20sec then the connection will drop and i cant connect anymore. but my wizard detects my router but it just on the screen that it is unavailable even though it shows a very strong signal.
i've tried to hard reset it and it doesn't work. i just wondering if there's a configuration i should do with the setting of my wifi? or is there an application that i can download here? and also i lost the voice tag program of my phone when i upgraded it to wm6.1, where cant i download an application for it?
thank you in advance!!! ([email protected])
Customer Call Details Nov 13 2008 04:37
I have an HTC Touch that can connect to other hotspots, but not to my home Belkin router. Sometimes, if there is another connection available, it can see the router, and says that it is Available, but cannot connect; other times it won't even see it. I have checked for firmware updates, but I have the latest. Any help would be greatly appreciated.
Belkin Response Nov 14 2008 22:18
Hi Lilburd,
Thank you for contacting Belkin Technical Support.
We understand that the HTC Touch does not connect to the router. We apologize for the inconvenience caused.
Please follow the steps given below to update the firmware and configure the router:
We recommend that you update the firmware from a computer that is connected to the router with an ethernet cable.
Please download the latest firmware on the router from the link given below. Download the file "3.01.29":
http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=10288&scid=0
and save it to the computer.
- To update the firmware, log on to the router`s web interface by typing in http://192.168.2.1 in the address bar of the browser. The computer should be
connected to the router with an ethernet cable.
Note: If you have changed your Router’s IP address, use that IP address.
- By default, the password is blank. Click the "Submit" button.
- Click on "Firmware Upgrade" under the option "Utilities".
- Click on “Browse” and select the bin file that you have downloaded.
- Click on “update” and follow the wizard.
- After updating the firmware, restore the router to factory defaults by clicking on "Restore Factory Defaults" under "Utilities".
- Reconfigure the router.
Please follow the steps given below for configuring the router:
- Connect the computer to the "LAN" port on the router and connect the modem to the Internet/"WAN" port, using Ethernet cables.
- Take a paper clip, insert the paper clip in the reset hole of the router and hold it for 15 seconds.
- The power light will flash and then come back "ON" solid, indicating that the router is being restored to factory defaults.
- The corresponding lights on the front of the router should be lit up.
- On the computer, check if you have an IP address in the range of 192.168.2.x.
- If not, specify a static IP address, gateway and "DNS" address by following the steps given in the link-
http://web.belkin.com/support/kb/kb.asp?a=2824
- Log on to the router web interface by typing in http://192.168.2.1, in the address bar of your browser.
- By default, the password is blank.
- Click on "Connection Type" in the left hand column under "Internet WAN" heading.
If the connection type is Dynamic (cable):
- Choose "Dynamic" and then click on "Next".
- Type in your “Host Name”, if your Internet Service Provider has provided it. Else, leave it blank.
- Click on "Change WAN MAC Address".
- Click on the button "Clone".
- Click on "Apply Changes".
If the connection type is PPPOE (DSL):
- Choose "PPPOE" and click on "Next".
- Enter the user name and password given by your Internet Service Provider.
- Save the settings.
- Click on the "Home" link at the top of the screen.
Internet Status should show "Connected" on the top right hand corner of the web page.
If the problem persists, please get back to us with the following information:
1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or static).
2. Name of the Internet service provider (ISP).
3. Version number of the router. You would find the version number on the bottom of the device. It would be a number in a series of thousands with a prefix “ver.”.
4. If the internet connection is stable on the computers using the router?
5. If the HTC Touch detects and connects to other networks in the neighborhood?
Lilburd, if you need further assistance please feel free to write back to us and we will be happy to assist you.
Regards,
Belkin Technical Support.
This was the response I got from Belkin after emailing them. It worked like a charm
Registry option
Not Sure about this one, but if you use SK Tools, or find the registry values yourself, there is an option to activate on the Touch, the 801 g networks compatibility, for some reason they are compatible but the option comes 'off' by default.
Paul
THANK YOU - Wizard 9100 now connecting to belkin N1
thank you - I had the same problem as original post - I updated using the pre release belkin firmware and it works now.
Excellent!
I was pretty sure that it was an incompatibility issue between HTC and Belkin.
Thanks a lot for this patch, you saved my (wifi) life ^^
This update also worked with my Kaiser! I was pulling my hair out trying to get it to connect. Thanks a lot!