I have a qtek9100
now,I have an issue,when I connect it to my computer using the BT dongle and activesync I can surf the web for about 30mins or less,than nothing seems to work,the connection is still alive,but I cannot enter any site.
I have to shut down the BT connection,and connect again.
but when i Do it,the device begins to work super slow,and i have to soft reset..and then again..
what can be the problem???
I have AS 4.5 beta (also tried 4.2).
Related
Hello,
I'm using my Jam for a while now with great pleasure, and active sync via bluetooth as well. I have rom 1.11 installed. A while ago i tried something new with bluetooth, it didn't work out that, and active sync didnt work anymore (via bluetooth) So I reinstalled it again, after that the problem started. If I connect my jam to the pc using the usb-cable it connect immediately, and I can browse my jam using Pocket Controller. But active sync doesnt start synchronizing right away, actually the whole program freezes. If i look in the task manager it says: Active Sync - Not Responding. Then I wait a minute or two and it starts working again, synchronizing etc. Anyone has an idea about this?
No one?
when i plug my jam in using the usb cable activesync starts up fine and everything goes normal but then it randomly disconnects and says Not Connected on activesync. i was using activesync 3.8 but i just installed 4.1 and still same thing. i'm running 1.12 wwe, any ideas?
This same thing happens from time to time with my MDA II (1.72 WWE, Active Sync 3.7) when I don't send any files over to the PPC for some time. It will randomly disconnect and then reconnect on its own at irregular intervals.
Hi everyone,
since today my magican will no longer connect to activesync.
when i plug my usb cable it is showing connecting to host and valid userinformation* (don't know the correct words, i use the german rom)
after that the activesync icon appears as connected and a half second later it dissapears. on pc my activesync icon rotates and tries to establish the connection.
when i try the connection via bluetooth the same happens.
i have reinstalled activesync 4.0, uninstalled it and tried 4.1 version...
the same problem, the rotating icon but permanent
could anyone help please? yesterday and all the days before it worked fine.
thank you all for ur help
phr³³k
I've managed through pain and misery to get Activesync to work through bluetooth (not easy with widcomm stacks as drivers).
When my PC boots up, Activesync (PC) will complain that the bluetooth COM port isn't connected (obviously because my phone isn't connected through bluetooth 24/7)
So everytime I reboot my PC, I have to re-check the COM port connection in the connection options (PC) to make Activesync listen to my bluetooth COM.
Any suggestions?
Also, I know that when my phone is connected via USB, my phone will gain access to the internet (My PC has the internet connection and shares it to the phone). With bluetooth I havent been able to get this to work. Yet both USB & bluetooth work through Activesync. Is there something Im missing?
Thnx! I hope this isn't too specific/complicated like question
I used to have some of the same problems. What I found that usually it was 2 things causing it.
1. Activesync - Installation or Configuration
2. BT Software - Installation, Configuration or Need BT Software upgrade
What fixed my issue was 2 fold: activesync settings & needed to upgrade my dongle's software.
Activesync: When I installed 4.5 it setup a network connection that kept running in. And when I started up my PC I could see the icon running in my sys-tray (and would have troubles on and off again either with bluetooth / USB sync. What I found that worked for activesync was uninstall and make sure you check off allow wireless activesync connection. I've also found it likes to use com 3 for BT activesync.
BT Dongle: I have Motorola PC850 dongle and found that there was a great new BT Stack update that would hold the settings even if I turned my PC off for weeks at a time or removed the dongle to somewhere else. Plus it fixed the issue I had with using my BT stereo headset, to listen to music with out pops and skips. Oh In your BT settings make sure that com 3 or what ever your using is the same as activesync
Hope I can test those few tweaks.
However, after connecting my phone to activesync by USB, now my phone won't even connect by bluetooth to my PC anymore.
STUPID STUPID bluetooth stacks
I have the latest ActiveSync, and a 8525 using Windows XP SP2.
ActiveSync was working fine until 2 weeks ago. Now I get an error saying its an unrecognized USB device. If I repair ActiveSync it works only 1 time then I have to repair again.
The phone charges fine, no other issues.
Could this be a USB issue on the phone?
i would first try a different cable or usb port on the pc
Ill give that a shot.
Still does the same thing. Charges fine.
Sometimes it will connect to ActiveSync then drop randomly.
Sometimes when I plug it in it doesnt recognize it.
soft reset your phone and then turn active sync on and off on the phone. Then try to connect.
I had a similar problem. whenever I connected my tytn to my pc, It wouldn't even charge my phone, nor would it activate active sync. the PC wouldn't recognize my device.
The solution that worked for me was to connect it to my pc, keep the PDA on, go into device manager, network adapter - and there it was - the windows mobile based device was disabled..
I have enabled it and now all is back to normal...