Hi,
can O2 ATOM use WPA-PSK ?
I am setting my AP and my atom - and no packets are seen on the AP !
("control" laptop connects fine)
ugilad,
Yes the Atom uses WPA-PSK. I am running WPA-PSK at home and it works perfectly.
i also have a wireless network running WPA-PSK encryption and i can connect without any problems. upgrade to the latest firmware for the atom if you haven't already as it has a better wireless manager. another thing to note is whether you have mac address filtering on your network in which case you would need to add the mac address of your atom to the wireless router's list.
WRT54GX v2
does anyone have any success using WPA-PSK with Atom Exec on Linksys WRT54GX v2?
Related
Hi, maybe someone could be of any help
I tried out allready a lot and do not see a light at the end of the tunnel.
I am trying to get a TyTn to connect to CISCO APs using WPA with LEAP or PEAP or WPA-PSK and i do not manage to get it connected. The TyTn "sees" the network (SSID is hidden), tries to connect but did not manage to get connected. I tried with allmost any ROM available here. At the moment i am using the I-Mate on:
ROM version: 1.20.305.3
ROM date: 07/21/06
Radio version: 1.07.03.10
Protocol version: 32.41.7010.02H
Any help would be appreciated
Same problem here w/the Cingular 8525 and Cisco AP
Been the Cingular 8525 the same as the HTC TyTN, and using Cisco AP's at work I'm experiencing the same problems here.
The Cisco AP log shows a failure on the TCP/IP handshake when my 8525 tries to authenticate. We're also using WPA-PSK. Cisco support analyzed the log and found no explanation on why it cannot complete the 3 way handshake.
I can use WPA-PSK in my home network with a D-LINK DI-524 w/o any problems.
The next test will be to try a Linksys/Cisco router and WPA-PSK at a friends place, also I will try WEP (just for testing) at work and if I can w/o any encryption on the Cisco AP that is giving me problems.
I'll also try contacting HTC Support.
Thanks to anyone that could help, I will post any results of my tests.
Cyberg
The Wizard doesn't seem to support AES. Maybe other HTC devices have the same problem. I've also had trouble with routers running in dual AES/TKIP mode. Try setting TKIP only.
WM5 does not support AES. WM6 supports!!!
Entering the following line in the Cisco AP Config fixed it for me:
dot11 wpa handshake timeout 1000
I too am having troubles with the tytn and cisco AP's.
Ive done some testing
Encryption: none works
Encryption: WEP64/128 works when entering code in HEX
Encryption: WPA-PSK (HEX KEY, 64 digits) works
Encryption: WPA-PSK (ascii, 8-63 digits) FAILS
I will try the dot11 wpa handshake timeout 1000 later today, hope it fixes it.
Also noticed that my Hermes won't connect to my parents router (SSID hidden, WPA-PSK of about 16 digits). Somewhat frustrating, but never mind. Router in question is a Thomson Speedtouch 5xx (can't remember exact model number).
Go into Wireless LAN & Power Mode & max it out to Best Performance.
Same problem here... with my Tytn and an old 3com OfficeConnect b.
No way to enable WEP encryption (authentification will always fail).
Working perfect now with data encryption disabled: connection security made by letting only authorized mac-address to connect.
This way is also more secure than WEP encryption, am I right?
I will try the dot11 wpa handshake timeout 1000 later today, hope it fixes it.
Click to expand...
Click to collapse
Go into Wireless LAN & Power Mode & max it out to Best Performance.
Click to expand...
Click to collapse
Neither of these fixed it.
Its like the Hermes will only accept 64bit Hex key, which is fine but one of my other devices will only accept upto 63bit Ascii key
I had issues with my Cisco 1100 AP's and read somewhere on Cisco's website that QoS must be disabled on the Radio interface to get WPA/WPA2 to work:
Code:
interface Dot11Radio0
no dot11 qos mode
It worked for me
Andy
ADB100: Tried your code, still not working
Ive gotten WPA to work but only when useing the full 64digit key in HEX,
I think the Tytn has troubles with using ascii in WPA.
I had the same problem as the starter of this topic with Linksys WAG200G router, just couldn't set up to connect with WPA, so I switched back to disabled security with restriced access on trusted MAC address, and now it works like a charm.
WPA-PSK
Works for me. I have a Linksys WRT54G, and an 1100 AP. Connects to either of them seamlessly.
Just to add some more info in case anyone else stumbles on this thread.. had very same issues with WM5 on stock Hermes (T-Mobile VarioII). Had to unprotect the netork and rely on MAC filtering
Installing WM6 using Black 2.5 (now on 3.0) sorted the problem immediately. It seems some routers expect certain things from the device when using encryption that WM5 can't always provide (AES has already been mentioned). Yet another god reason to upgrade to WM6
Router here is Philips SNB 5600.
Hi
I'm having a similar problem with my Orange M700 (HTC Prophet) and Netgear DG834G.
Anyone any great ideas???
Andy
Has anyone tried to use their TyTN with a WRT54G Router. I can get it connected to the wireless signal and it has a DHCP IP but I cant seem to get it to automatically pickup the DNS servers. I an connected to the WAN via PPPoE. The connection is 100Mbit FTTH. The PCs wired to the network can get on the net just not the TyTN on the wireless signal.
Any help is appreciated.
Nevermind
Put the DD-WRT custom firmware on there then set the DNS servers manually and its blazing.
Hermes (Dopod 838 Pro) and the WRT54G Router Issue
I have the same problesm! I run a WRT54G router AP at home and created a MAC list that enables access. Of course I updated the MAC list filter on AP. I get to connect my JasJar, but no such luck with the TyTN. Then I hooked an ASUS portable access point to one of the routers cable slots and my TyTn connect seemlessly!
I read the DNS suggestion and alos trying to run the AP woth fixed IP! I would then have to do that for all systems that access the Routre, right! Isn`t there a way to make th 54G work with DHCP and assign IP addressess dinamicly to the TyTN, as it does to any other WiFi equiped device?
Try this;
Check what type of wireless encryption you are using. If you are using AES then create another SSID or change the current SSID to use TKIP for your TyTN to connect to. I don;'t think the TyTN supports AES.
Later, Lew
ooops
oops, ignore my reply. Clicked on the wrong button and accidently replied here
you can always do this... sell your linksucks on ebay or to a friend then go buy a better router i have seen many issues with linksucks and HTC devices, there was tons of weird issues with the wrt54g and the wizard
Mine works without issue. I do have the sveasoft firmware loaded though. I also don't use pppoe.
Load the DD-WRT and it's very stable..
I have a DLINK 604T and it work with no issues with dynamic IP/DNS. This router is also cheap as compared to lynksys
WRT54G working FINE with Hermes 100
Hi Everyone!
If you own a WRT54G router/access point and were experiencing trouble to connect your Hermes 100 to it, sweat no more! Go www.linksys.com, select downloads and choose from the long list of routers. Make sure you match the model number and the version number of your router. Download the FIRMWARE upgrade. I was running the original firmware from my router a WRT54G V1.1. After upgrading the firmware, my router worked great and the range was almost 4 times what I had before!
Check it out!
Cheers
Michael
Dopod 838Pro
Was a bit worried as read this before my Vario II arrived and I have a WRT54G...
Connected fine 1st time... just added MAC to filter and put key into vario. bingo-bango!!
FYI I have WRT54G Firmware Version: v1.42.2 (the firmware I bought it with)
Hi,
i have strange problem with my htc 3600 and siemens wifi dsl router se568. My ppc connects to router but i can't ping router or access internet or any other computer on network. Strange thing is that my ppc connects to other wireless networks without problems. I tried 2-3 laptops and they connect to siemens router. Also i tried some other pocket pcs and they connect also to my siemens router. only combination that doesn't work is my htc 3600 and router.
Anyone has any suggestion how to solve it?
One more thing i use WPA-PSK TKIP encryption.
Igor
komple said:
Hi,
i have strange problem with my htc 3600 and siemens wifi dsl router se568. My ppc connects to router but i can't ping router or access internet or any other computer on network. Strange thing is that my ppc connects to other wireless networks without problems. I tried 2-3 laptops and they connect to siemens router. Also i tried some other pocket pcs and they connect also to my siemens router. only combination that doesn't work is my htc 3600 and router.
Anyone has any suggestion how to solve it?
One more thing i use WPA-PSK TKIP encryption.
Igor
Click to expand...
Click to collapse
Ok found solution. For some strange reason when I put wifi preferences fon pda Best Performance it connects and works fine. When i return it to Best Battery it will not connect. Strange. Probably it is something with my wifi router.
Igor
I am trying to enable AES encryption on O2 atom so that I can connect to Office Lan using WPA-AES. Currently only seeing TKIP option.
By the way, I am using WM5
Can any one please help or suggest alternatives.
Regards
Praveenvj
praveenvj said:
I am trying to enable AES encryption on O2 atom so that I can connect to Office Lan using WPA-AES. Currently only seeing TKIP option.
By the way, I am using WM5
Can any one please help or suggest alternatives.
Regards
Praveenvj
Click to expand...
Click to collapse
I have tried playing the wireless connection function of an ATOM black with a router the other day. The router is working properly which is being shared by few clients, and was set up with WPA-PSK (with either AES or TKIP); hence, I configure the ATOM black with WPA and TKIP but it kept connecting and disconnecting. Finally, I disabled the encryption with both router and ATOM and tried again. This time, the two devices talked to each other. Put the encryption back to the devices but failed the connection again. Think that WM5 is not geared up with wireless encryption. **Have not tried the OPEN, SHARED nor WPA though** --- Julian
Upgraded to WM6 still no WIFI access
Hi
Thanks for julian to try and help.
Since it was not working on WM5, i installed WM6.1 ROM on my phone using file PDAVIET_ROM_WM61_OS20755_ATOM_Sonblack.exe. Still I do not have ability to connect to my WIFI network. I see that under Network settings, even now for WPA and WPA-PSK only TKIP is listed.
Error i get is : "Network requires you a personal certificate to positively identify you"
My friend has HTC touch with same settings as mine and he can connect to WIFI. Is the O2 atom missing some modules. I find that my friend's mobile has AES encryption along with TKIP even though TKIP is being used.
How can I install WPA2 on the above ROM. That is one thing that HTC touch shows which my phone does not have as well.
Regards
praveenvj
I have not been following up the thread with PDAVIET WM6.1. So I cannot comment your problem.
You may want to access the following thread hope it will give you hint on your certificate problem.
Good luck,
Julian
I have the same problem anyone help?
Hi all,
i am new here
I have problem with my Xperia.
When i connect with my phone to unsecured Wifi network everything works fine.
But when the wifi network is secured (WPA2), i cann't access the internet. (IP address is assigned, but ping to the router is without answer)
I have allready trying to set the IP address manualy, but without any success.
Can somebady help me please?
Thanks
BR
Edo
Is the WLAN-SSID hidden? That often makes trouble with devices like Phones, Radios, MP3-Players or something else. If so try to activate SSID-Broadcast (unhide SSID) and connect again.
What does your phone show in it's wireless settings (IP, Gateway, Subnet, Encryption etc)?
On my Cisco router I use WPA2-PSK Authenication with AES-CCM Encryption. The SSID id is hidden. No problems at all....
Is your router using MAC Address filtering??
This will also make it unresponsive to pinging if it is Enabled
and your x1 in not on the permitted list!
good Luck.
Stuart
hi,
now i use only MAC address filtering (without WPA2) and it works fine.
(SSID broadcast is enabled)
With activated security WPA2, MAC address filtering dissabled, SSID broadcast enable/disabled, it doesn't work
Tested with wifi router Belkin.
With HTC Diamond it works fine also with WPA2 secured network.(almost the same HW like the Xperia)
Tomorrow i will "play" a little bit with the router and phone settings.
It must works !!!
Note: i have observed the same problem/behaviour with nokia E66 (OS Symbian)
Hi,
Netgear Router.
WPA2 enabled.
MAC filtering on.
Broadcast Off.
Device added.
Browsing a doddle.
Des. . .
Deactivating the encryption nor use of wep is never a good idea.
Try to change to wpa-psk tkip.
I'm not sure what it could be, but there are some articles on the internet that WinMo phones (in general) have trouble using WPA or WPA2. WEP is apparently fine to use, but then again not secure.
I have a netgear, and using WPA/WPA2 (no MAC ACL) on my router with the Xperia doesn't work, but some of the other guys work fine
Try updating your Router Firmware (or making sure you have the latest firmware flashed to your Router) - this has been known to solve connection problems with new hardware e.g. Windows Mobile or PS3 or Wii.