Can it permenantly destroy or harm it if i overclock to lets say...280Mhz?
and also,what is the best /recommended overclocking software??
thanks
You could damage your device trying to overclock too high in theory - but it rarely seems to happen. The device most often goes to a white screen and soft resets, You have to find a stable speed for your device - 240mhz omapclock speed = 260mhz real speed -seems to be stable for most people.
Use omapclockplus http://forum.xda-developers.com/viewtopic.php?t=56057&highlight=
Or batterystatus (with today plugin) http://forum.xda-developers.com/viewtopic.php?t=55782&highlight=
Or you could use omapclock with smartskey or memaid/sktools
choice is yours :wink:
I haven't had any problems so far, but am running it modestly overclocked @ 247 Mhz. I am using the batterytodayplugin, works great.
Possibly I'll bump it up another notch to 260, but for now I don't need that extra speed...
One advice - go slowly. Increase in increments, and wait a few days between each higher overclock value. That way you can determine if it is stable.
Related
Dear all,
Do you know the overspeed for the O2 mini software Pocket Hack Master, attachment is full version share for all O2 mini fans
Good? Are U sure U can o/c yr jam stablely? So far, I don't see any o/c software run stable on jam.
I tried running my mini at 520mhz using pocket hack master. It ran quite fast indeed, then it did a hard reset after about half an hour.
I didn't bother to re-install hackmaster after that, but before I tried overclocking it, I was experimenting with underclocking it to see if the battery life would be extended. I didn't run my experiment long enough to see tangible results though. Anybody else tried underclocking their minis/jams?
xcpuscalar
i always use xcpuscalar, to underclock and sometimes overclock my jam.
it works fine, and i think its easier than phm.
I did use PHM and uninstalled it. The thing is, that, for most cases, overclocking isn't neccessary at all. It only brang me some faster game speeds for some (!) games. But that's not worth it. The increase in speed is only slight. The disadvantage is the battery drain with PHM, even when underclocking resp. using the scaling possibiltity. Both drains the battery a lot more than without PHM running at 416MHZ. The problem is the voltage regulation which isn't working with PHM but which the CPU is regulating itself very well, when left alone.
So, if you aren't 100% sure that you need (a bit) more speed, forget about it.
Has anyone noticed any long term disadvantages to overclocking the Wizard? Does the battery life permanently decrease? What speeds are you running yours at, and how long have you been doing it? Have you noticed anything at all which indicates it's not good for the hardware?
Cheers
reply
i believe that it's safe to overclock the mda...just set it at an acceptable rate (264mhz for me) and make sure not to run the battery all the way down...if you overclock the settings too high the device will freeze and reset (this is a fail safe procedure it goes through), so there is no need to worry...also don't overclock the settings too low as the phone becomes disfunctional when too low (about less than 132mhz for me)...the screen flickers because it's not being refreshed quick enough (my guess)...hope this helps...
I would set it to 240. I have done before, i'm just wondering if it's a bad idea leaving it permanently set to that level?
Cheers
yea you should be fine at that speed, but if you want you can overclock it higher if it will let you...just make sure that the phone is stable when using it...like i said in my earlier post my device is oc at 264mhz
Cool, thanks for your replies. How long have you had yours overclocked for? Do you use Smartskey?
Cheers
My self i ownly use it when need the extra speed, only with some games and wmv video files. I think it definitely lowers battery life and i would have worries about overclocking all the time and the long term effect it has on the processor (not so important if you only keep your wizard for a year and then change with a new contract - what i do new device once a year!) I found good speed gains with the registry wizard - http://forum.xda-developers.com/viewtopic.php?t=39725
have not found overclocking produces that much extra speed.
My self i only use it when need the extra speed, only with some games and wmv video files. I think it definitely lowers battery life and i would have worries about overclocking all the time and the long term effect it has on the processor (not so important if you only keep your wizard for a year and then change with a new contract - what i do new device once a year!) I found good speed gains with the registry wizard - http://forum.xda-developers.com/viewtopic.php?t=39725
have not found overclocking produces that much extra speed.
Mine is also set at 264 24/7. Battery still lasts me all day. Been doing it since the oc program was found which I guess has been a couple of months.
Don't forget, you're wizard is only overclocked when it is active (i.e. not in standby mode). When your wizard goes into standby, it automatically goes back to the default 180mhz. Only when you bring it out of standby does it overclock again (assuming you're running it with smartskey with the option of overclocking on wakeup)
i'm using smartkey to constantly run at 264mhz...i have been doing this for a month now...like i said there is not really any problems with the batt unless you run it down totally...there was a post about this in the overclocking thread...the process is set low so that the phone will have a longer batt life...this was also stated in the overclocking thread...theoretically there is more wear if you overclock it since you are making the processor work harder, so use it at your own risk! if you want to be on the safe side then use smartkey and the overclocking prog in the same directory...then use total commander's note pad (while the ini file is highlighted) and change the value lower when you don't want it to constantly run at 264mhz or whatever speed you want to overclock or underclock at...just use it when needed, but i overclock mine constant 264mhz with great results combined with tweaks2k2, registry wizard, and of course the tmobile custom rom ...internet is a blast...just wish i could get it to run like the IE in a pc
anyways hope this helps out a bit further...
activesync
your activesync will hang allot if you overclock, I have noticed this.
DOnt know why.
For some reason i stumbled onto something, im sure its been mentioned b4 but when running Wisbar advance with a Windows vista skin done by xcillion, i am able to overclock my cingular 8125 to 288mhz at a stable rate with no problems at all, can run warcraft 2 full speed with over 50 units battling it out on screen, almost doubles browsing speed and i can run all the emulators including SNES at full speed with sound. when i dont have wisbar advance running i cant go past 240mhz clocking speed. I wonder has anyone else noticed this or gone higher than 288 without a freeze. Also, my battery life runs steady for a full day of browsing the internet talking on mobile messanger and listening to music at half volume for a full day.
Re: DOnt know why.
xSoNiCcRaCkErSx said:
For some reason i stumbled onto something, im sure its been mentioned b4 but when running Wisbar advance with a Windows vista skin done by xcillion, i am able to overclock my cingular 8125 to 288mhz at a stable rate with no problems at all, can run warcraft 2 full speed with over 50 units battling it out on screen, almost doubles browsing speed and i can run all the emulators including SNES at full speed with sound. when i dont have wisbar advance running i cant go past 240mhz clocking speed. I wonder has anyone else noticed this or gone higher than 288 without a freeze. Also, my battery life runs steady for a full day of browsing the internet talking on mobile messanger and listening to music at half volume for a full day.
Click to expand...
Click to collapse
hey sonic, where did you get your copy of warcraft 2 for windows mobile ?
I've never heard of warcraft for Windows mobile, how does it run on a 240 MHz overclock?
I got it from the Wargus engine. i can email you the files if need be, i dont want to jeprodize this sites reputation. The game last time i checked was free though...
Actually I'm not sure if it's the overclocking issue or not but ...
For couple of weeks now my Wizard's red led is on all the time, not like it is when your battery is very low but about half of this brightness. I'm not really worried about that, it doesn't change much but it may be connected with overclocking (it was 240 for about a month).
Another thing - once I had sth like 110% speed of every tone played, either a phone call or an incoming message.
It doesn't really matter to me since it's still working fine but it may mean that overclocking isn't that safe as we might think.
TroLoo
Hi guys!
I see that my Jamin is stable at 240MHZ... what is, in your opinion, the hi stable overclock for the Jamin... ?
O2 Neo
Hi, i run my O2 Neo at 240 stable. I'll probably try even 252. It's summer so I wouldn't push it higher than that. 252 could be stable, but depends on conditions. Just try it for few days.
Running at 240 MHz, it the battery life MUCH reduced than using factory 200 MHz speed?
My opinion - 'Sligtly' is more accurate then MUCH. But i didn't measure it.
252 MHz for 2 month on my XDA Neo with JAMin ROM, without any problem. Battery life is good, did not really see any difference before and after overlocking.
Well, I have been running my wizard at 264 MHz for 4 months straight and it has never failed on me. i have it on all the time after standby and soft resets. ive also tried 276MHz for a while but i had to soft reset it almost twice a day.
BTW, increasing the clock higher than usual does not heat up your device. the most it would do is soft reset it. temperature running at 264mhz is mostly the same as running at factory speed. (well for me it has) dont know about some of you.
lsnizzle said:
BTW, increasing the clock higher than usual does not heat up your device. the most it would do is soft reset it. temperature running at 264mhz is mostly the same as running at factory speed. (well for me it has) dont know about some of you.
Click to expand...
Click to collapse
How do ya measure the temp?
cellchamp said:
How do ya measure the temp?
Click to expand...
Click to collapse
Xbar can do it
Overclok on Dopod 818pro
Guys, my device is Dopod 818pro, and i was using OmapClock.exe to OvClock my processor, but, when the first time i run this program, the clock speed, says 264 Mhz? is it supposed to be the correct Processor Speed?
I got confused as i read anywhere else that the default factory speed is only at 180 Mhz.
But why is it my device gives me a 264 Mhz on Clock Speed?
also i've tried all the guides and tricks to keep my Clock Speed at certain number (eg. 216 Mhz). such as using a MemMaid and etc. but still, i always got the number 264 Mhz and it won't change at all... neither after soft-reset nor stand-by.
Anyone got the same problems?
I forgot to mention, when the first time i bought this 818pro, i felt that my device run very fast, even faster than my friends HP 6828 and ATOM PURE. Did i get lucky or sumthin'?
Everything on my device is still on factory setting...
i removed the OmapClock and Other Utility Software..
also..... there is one more sw.... 'Pocket Hack Master' from http://www.antontomov.com.... have a look whether it has compatiblity with URs.....
might be helpful.....
Mine has been stable at 240MHz for 2 months so about 6 weeks ago I bumped it to 252MHz and is stable since.
Nir
thanks! :wink:
Re: Overclok on Dopod 818pro
p12a said:
Guys, my device is Dopod 818pro, and i was using OmapClock.exe to OvClock my processor, but, when the first time i run this program, the clock speed, says 264 Mhz? is it supposed to be the correct Processor Speed?
I got confused as i read anywhere else that the default factory speed is only at 180 Mhz.
But why is it my device gives me a 264 Mhz on Clock Speed?
also i've tried all the guides and tricks to keep my Clock Speed at certain number (eg. 216 Mhz). such as using a MemMaid and etc. but still, i always got the number 264 Mhz and it won't change at all... neither after soft-reset nor stand-by.
Anyone got the same problems?
I forgot to mention, when the first time i bought this 818pro, i felt that my device run very fast, even faster than my friends HP 6828 and ATOM PURE. Did i get lucky or sumthin'?
Everything on my device is still on factory setting...
i removed the OmapClock and Other Utility Software..
Click to expand...
Click to collapse
Try installing the demo of sktools - its the only program I know that shows the true processor speed.
i did over clock to my device into 240, and it's works normally, but i don't know how to know that my overclocking was success or not, where can i read the speed of processor after overclocked?
rGrds
-wisnu-
how do i keep my device permanently on at a certain speed thgough omapclock?
also i would like the overlock to work at the set speed even after soft resets. Is this possible?
cellchamp said:
how do i keep my device permanently on at a certain speed thgough omapclock?
also i would like the overlock to work at the set speed even after soft resets. Is this possible?
Click to expand...
Click to collapse
Yes you can 2 simple methods here
1. Using omapclockplus - see here http://forum.xda-developers.com/viewtopic.php?t=56057
2. Use batterystatus plugin - displays Mhz on today screen and has omap functions inc device wakeup overclocking see here http://forum.xda-developers.com/viewtopic.php?t=55782
You could also use smartskey or notification queue method but above methods use easy install cabs.
median said:
My opinion - 'Sligtly' is more accurate then MUCH. But i didn't measure it.
Click to expand...
Click to collapse
Just tried - I agree, there is no big difference in battery life - similar autonomy than factory settings when running at 240 MHz...
Hi,
I really don't recommand to overclock the prophet over 240mhz.
I overclocked my first prophet @252mhz.
I had no crash problem with this overclocking, but it burned the bluetooth chipset.
Now i have a new one and have a permanent overclock @216mhz, and sometimes i overclock it @240mhz, but usually it' only to do some tests!
The 216mhz is more than enough to do what i want.
Bye
Herc. 8)
Guys,
I just clocked my 9100 to 264mhz and its running very stable and fast. Howver Id really like to have a small test program that can tell me exactly how many mhz its actually running at.
Who's got a small application that can tell me the speed in mhz ??
I use BatteryStatus.
http://forum.xda-developers.com/viewtopic.php?t=55782&highlight=batterystatus
You can also use a product like SKTools which is a great util for WM devices.
HTH!
Thanks dude......Im apparently running at 286mhz......even though Ive only clocked it to 264
Which application did you use to overclock your CPU? I've tried OmapClock (and went upto 220MHz), but it freezes frequently...
not all wizards can go much beyond 240, mine is fine at 240 but my friends only goes to 220MHz without crashing.
Luck of the draw i guess
guess i got lucky... constantly @276 and stable...
I saw someone has asked about which ROM is stable and how far can you overclocked
I have a Jamin G4.
Have flashed with PDAViet 4.0.0.0.6 Touch. I have not problem at all since.
I also used Battery Status and overclocked the CPU up to 286MHz... it runs ok so far
But when I tried 299MHz or higher, the PDA hang.
TIPS for overclock:
- For safety: set
+ Ticked: "OVERCLOCK ON WAKEUP"
+ Unticked: "Remember last CPUSpeed" and "Overclock after Reboot"
- Reasons because in case if the PDA hang, a reset will put back the clock to default or 195MHz (in my case)
- Overclock less or closer to the default 195MHz is better unless you need high clock for some reasons.
I think fast clock, will use more power, therefore drain battery quicker and probably shorten your CPU lifetime
I hope this would help to answer a number of questions for someone