My Mini S died? - 8125, K-JAM, P4300, MDA Vario General

So I thought the battery was drained. I plugged it in, the orange LED came up. Everything seemed fine.
When I look back after a while, all LEDs are off. The device does not respond to anything - power on button, soft/hard reset...
Basically it looked dead to me.... Help please !

I've seen this before... It looks like the battery is completely drained as well as the internal battery which controls the battery software.. (And stops you charging the battery
There is a way to jumpstart it somewhere on this forum, but before you try anything like that try plugging it in and leaving on charge for at least 24 hours, or maybe trying another charged battery

Related

Battery Charging Issue

Does anyone know if the Wizard is capable of charging its battery in a completely powered down state?
The battery on my Wizard (G4 Qtek 9100) was low today, but I just ignored it, the battery ended up running down completely to the point that the phone powered off, and would not turn back on when I tried to repower it. I connected the charger and left it sit for about half an hour, the charging light did not light, but I left it to charge. After the half hour I figured it should have gained enough charge to power on, so I tried and no luck. Luckily I have a charged spare battery, so I left the dead battery in the phone and wedged thin wires in between the dead battery contacts, and the phone's spring loaded contacts. I connected the + of the dead battery to the + of the spare, and the - of the dead to the - of the spare. Now both batteries are connected to the phone in parallel. This allowed me to power the phone up and boot it all the way up, where the charging indicator LED lit. I disconnected the spare battery, so that the dead battery can charge on its own. Sofar it looks like it is taking the charge.
I'm wondering if some of the people that have "bricked" phones might have run into the same problem that I have. If you have a "bricked" phone, try using another battery that you know has a charge.
go in registry with totalcommander or something similar to this key:
HKLM\Drivers\BuiltIn\usbfndrv
and change : EnableUsbCharging to '1'
press reset after u done this.
i had this several times with death battery and wouldnt charge on usb on the
computer but it did with the original charger.
Thanks, i'll give that a try. Just curious, do you know anything about how that works? I'm wondering how a registry key can controll a piece of hardware that has been completely powered down, and that windows mobile hasn't yet booted on.

Wizard suddenly died yesterday

Hello,
I've a Wizard that is approximately 20 months old. Yesterday, before I went to bed, I set the alarm clock on the Wizard, put it next to bed and went to sleep.
This morning upon waking up I tried to switch on the Wizard but it couldn't. Firstly, I thought the battery was discharged, so I tried charging through USB on my computer -- it wouldn't charge or start. Then, I tried charging on the default charger -- again nothing.
I tried removing battery and soft reset - nothing. It's really weird, yesterday I left it working, no-one has touched it and today it's totally non-responsive.
Any ideas what might be wrong/how can I bring it back to life? Would a hard-reset help?
Regards,
1. how much charge was in the battery last night?
2. is your battery 20 months old also?
3. do you have a spare battery to try?
4. do you have many applications, music etc. on the device?
1. how much charge was in the battery last night?
Click to expand...
Click to collapse
Unfortunately I can't remember, however I have an alarm which sounds periodically when the battery is below 20%, so I'm guessing I had at least 20 percent. Could be wrong, of course, but most likely above 20%.
2. is your battery 20 months old also?
Click to expand...
Click to collapse
Yes, this is the original battery. Aprx. 20 months old.
3. do you have a spare battery to try?
Click to expand...
Click to collapse
I don't have that. I guess I could go to mobile phone service shack and check there. Do you think it's the battery?
4. do you have many applications, music etc. on the device?
Click to expand...
Click to collapse
The Wizard came with a 64MB card I think. I had around 10MB free space. 3-4 applications, 2-3 mp3s. Nothing unusual.
Same thing (sort of) happened to mine after about 187 months. I was using mine and it hung up. I hit the reset button and that was the end of that. Even when plugged in it does nothing. Tried a hard reset... nothing. Soft reset.... nothing. Dead. Zip. Nadda.
Good news? Replaced it with a Kaiser!
vivanov said:
Hello,
I've a Wizard that is approximately 20 months old. Yesterday, before I went to bed, I set the alarm clock on the Wizard, put it next to bed and went to sleep.
This morning upon waking up I tried to switch on the Wizard but it couldn't. Firstly, I thought the battery was discharged, so I tried charging through USB on my computer -- it wouldn't charge or start. Then, I tried charging on the default charger -- again nothing.
I tried removing battery and soft reset - nothing. It's really weird, yesterday I left it working, no-one has touched it and today it's totally non-responsive.
Any ideas what might be wrong/how can I bring it back to life? Would a hard-reset help?
Regards,
Click to expand...
Click to collapse
Mine died too when i was flashing...
Leave the phone in the original charger for a while and see if it picks up...sometimes it comes back to life by doing that...
If that doesnt work, try a new battery, you might be lucky...
A somewhat strange development occurred today:
Today (3 days after it stopping working) I randomly tried to switch the Wizard on and it indeed switched on. It showed that it had 0% battery. It didn't even show 0%, basically the battery charge graph was empty - no number, no fill, nothing.
While it was on charge the charge light was on (while it was 'broken' the charge light was off when I tried to charge). So I left it to charge and when I checked back in 15 minutes it was back to being 'dead'. Can't be started, no charge light, nada.
I don't really know what's going on, however I'm highly suspicious of the battery. Currently, I'm periodically trying to switch it on again so I can backup my data.
Any ideas what might be wrong with it, do you think it's the battery or is it more serious?
Regards,
The battery won't charge if it gets to low.
There is a thread about using a 9V battery to get the battery up to a level so it will charge. I don't have the link for it, try searching for it or maybe someone else will reply.
You might have a bad battery. I bought a new battery because I didn't think I was getting the life that I should. I tried using the old battery about a month after when I had to run out and my main was low. About 15 minuets later my phone started shutting of and rebooting. That was the end of that battery.
Yep, it's possible. If the battery is to empty, you can't charge the phone. It is stupid but it's just like that. You also can't power on the phone without a battery with the charger connected.
Yesterday I received my wizard and I had to revive my battery too because it was completely empty. I used a self made 5V power supply and after 2 minutes charging I placed the battery in the wizard and was able to charge and boot with the charger connected.
Here's the 9v battery trick, connect the + from the 9v battery to the + of the phones battery and the - to the -, hold there for only 10 seconds then remove the connection for 10 seconds and then repeat the process about 8 to 10 times and then put the battery back in the phone and connect it to the wall charger to fully charge.
Thanks for the advice. I'm going to do the jump-start thing.
However, I've hard time determining which is the - and which is the + pin layout on the battery, since the label is not correctly applied.
As far as I can see the - is the one at the far right, however I'm not sure which is the + pin.
Can someone help me with this, please?
Regards,
vivanov said:
Thanks for the advice. I'm going to do the jump-start thing.
However, I've hard time determining which is the - and which is the + pin layout on the battery, since the label is not correctly applied.
As far as I can see the - is the one at the far right, however I'm not sure which is the + pin.
Can someone help me with this, please?
Regards,
Click to expand...
Click to collapse
When you take out the battery and put it back in that direction ,turn and face up the connector side fasing you,the first connector from the rightside of the battery is the ' + ' and the last is ' - ' towards the leftside.Be careful while connecting and try not to touch other connectors. Don't keep the connections longer then 10 seconds interval.
good luck
Xeno1,
My MDA battery also died and went below re-chargeable state. Your trick to use 9volt battery to jump-start it worked just fine for me. I connnected for about 20 seconds (2x times) and plugged it back into phone and connected USB cable to it and my nice yellow charging light came back on. After about 30 mins, I could use the phone.
THANKS FOR THE GREAT TIP!!!
easier fix, take a standard usb cable. rip off the smaller end with a wire cutter, expose the red and black wire. take out your battery, than connect the negative(black) wire to the negative end of the battery, than the red wire to the positive end of the battery, leave it in there for exactly 3-5 minutes for jump start. after that turn your wizard on, and quickly shove it inside a new usb cable. or the wall charger.
note:
if not done correctly, you may damage your wizard or the battery. if theres a power overload or your power goes out. your wizard will burn out!
feedback is greatly appreciated.
p.s after that my battery seem to be weak, charge barely holds for 12 hours. after 12-14 hours it will die out. so i suggest buying a new battery after couple of days.
Thanks guys! Vario died yesterday and wouldn't turn on or charge.
Tried the 9v battery recommended here and it worked! I was a little unsure which end was - and which was + but using the advise above, got it right. Wasn't too worried as found and ordered a replacement from ebay this morning for £7.
The first connector on the right hand side, nearest the end of the battery is the + the one more towards the middle and further away from its corresponding end is -, or at least, thats what worked for me.
Thanks again!
Experiencing the same issues after I set aside my Mini S as it was experiencing problems with regards to its screen alignment. Wasn't able to charge it during that time I kept in the drawer unused - due to frustration as I can't use it anymore. After downloading a guide to disassmble it so I could remedy the problem I found out that it won't power up anymore even with a new battery.
Well, haven't tried the jumpstart thing and the original battery was disposed of already to try the jumpstart idea. Could it be the internal battery is causing the problems? I opened my unit up and tested the internal battery for power and it registers a measly .2V left. Will use the 9V thing to power it up (as been doing that before on watch batteries that are hard to find replacements) before I do it on the main battery. Here's hoping it works as the Mini S has been quite useful for me until now.
UPDATE: I charged the internal battery and it now reads 1+ V and the external battery at 3+ V. No luck yet though as the unit still won't show any life. Any suggestions?
Vivanov, I know it's been a few years now, but did you end up fixing your problem? If so, how?

HTC not charging after empty battery

This morning my HD2(7) was totaly empty. The power button did not do anything and the phone won't start up. When I hooked it up to the charger, the red led did not come up and the phone was not charged at all.
I tried to do a soft reset, but nothing happend. Some posts on this forum suggested a hard reset, but I did not want to loose all content on my phone.
It seems that the real solution is very simple. Just connect the phone to a charger, remove the battery completly and then place the battery back in the phone. The HTC will now start up and begin to charge.
So, just a waring, do not hard reset when you phone stops charging...
Cheers, Rene
Funnily enough I put my phone on charge last night, forgetting that I'd also switched it off... Came to it this morning and remembered about the charging issue when switched off. Tried to switch the phone on and nothing... So I went to change the battery with the wife's HD2, but managed to mix up the batteries and found that my phone would switch on afterall and it was also fully charged. The wife had her's on charge overnight as well, so both batteries were showing as being full...
Charging issue has been fix up in the MAGLDR 1.13 version
knaar00 said:
This morning my HD2(7) was totaly empty. The power button did not do anything and the phone won't start up. When I hooked it up to the charger, the red led did not come up and the phone was not charged at all.
I tried to do a soft reset, but nothing happend. Some posts on this forum suggested a hard reset, but I did not want to loose all content on my phone.
It seems that the real solution is very simple. Just connect the phone to a charger, remove the battery completly and then place the battery back in the phone. The HTC will now start up and begin to charge.
So, just a waring, do not hard reset when you phone stops charging...
Cheers, Rene
Click to expand...
Click to collapse
There is no doubt that this is sensible advice, but there may be an overlap with another issue here.
I have noticed - and it could just be specific to my phone - that if the phone gets to the point where it shuts itself down to conserve power, it will often not restart from the power on button and only pulling the battery will wake it up. This seems to be a 'feature' of WP7 on HD2.
Interestingly, on several occasions where the battery has been fully charged (and still plugged in) the phone will not start from power on if I do a shut down - I tried it less than an hour ago after making a couple registry tweaks and only pulling the battery would persuade a fully charged phone to restart. It would be interesting to know if others are finding the same.
Where the battery is seriously discharged, it can take several cycles of pull battery - boot phone - phone decides it has insufficient battery and shuts down - pull battery - boot phone...before WP7 decides it has had enough juice trickled back into it to be able to charge - sounds crazy, but there you go.
MAGLDR v1.12 doesn't support charging, which doesn't help. I'm going to try v1.13 to see if agarp is correct - here's hoping.
Update: I don't think MAGLDR113 supports charging directly but I believe it has something built in to prevent a plugged in phone running down the battery. Not sure about exactly what, but it suggests something about booting the phone if plugged in and battery is at critical levels.

Streak 5 dead, what now?

Hello! i have problem with my streak 5, few days ago battery drained out and phone shut down.
i connected ti a charger but nothing happen, no reaction on phone so i left it on charge all night.
Still no response, no picture on the screen, no backlight, no LED, completely dead.
I can get reaction only when i enter in fastboot mode (holding power+camera)
IN this mode touch screen not working, computer recognize device and i can do flash and i do it successfuly but i still cant turn on my phone.
What can be a problem, I tried everything with no luck, also i have not found anyone with same problem
I have 2.2 official, no root.
Try changing the battery. The one you have could be defective, or else there is an issue with the charging circuit.
I measured with instrument 3,67V, connected od 1 and 4. And few other combination i get from 3,30 to max 3,67V.
This seem to be ok, regardless of that you think might be the battery?
Never let the battery drain that much becase now the battery doens't have enough power to start the charging... you should charge the battery manual with some wires on (+) and (-) from a old phone charger be carefull with the voltage(V) and the ampers(A) not to brake the battery, 20 or 30 min should be enough, or you should buy one of this Universal charger. Then place the battery in the phone and it should work ok .
This morning I optimistically tried to turn on a phone and it was successful
battery Indicator showing 7% so i connected to charger, now is normaly charging, everything is working normally...
I do not understand, what could happen? i few times drained battery to 0% but still able to charge, maybe battery is problem, but again, turned on after 3 days
Don't worry the battery is ok the problem is not to empty it again to 0%, at 5% 7% close the phone if you don't have a charger to charge it. This method applies to every phone and battery. It's not a good thing to fully discharge.
Now is fully charged and power is 4,07V.
So obviously battery caused this problem.
I think, good info for all who suspect on battery, 4,07 V is power you need to have on fully charged battery.
With 3,6V you cant event turn on the phone.
Thank you for suggestions

BATTERY (?) Help

Hi Guys, so I flashed Resurrection Remix and it was working fine. Few days later, I woke up to my phone continuously vibrating. Upon checking I saw that it was vibrating because it was doing a boot loop. Unfortunately my PC was broken at the time too, tough week.
Anyway, I let it do it's thing until it runs out of power. It never did. Seriously I waited for a day. When I slept, it had 20% battery (not charging). So I thought maybe, the power button is acting up again which has happened many many times before.
So I opened up my phone and adjusted the power button. Even, holding the volume up while plugging in didnt work anymore.
While I was there I saw the battery connector thingy, I unplugged it and re plugged it real quick without breaking anything. And It restarted and the device worked fine.
But.... The battery icon is steadily at 50% for a min then drops to 0% even while connected to charger. So, I charged it for a few minutes but it doesn't move.
I was about to do a factory reset but it shut down. The battery icon doesn't appear, only the red blinking led light. I tried charging it like that overnight to no avail.
I then tried to remove the battery connector again and as soon as I plug it, the screen turns on then off again. Sometimes it gets to the battery charging icon before it shuts down. If I bend the connector downwards it sometimes turns the screen on and sometimes doesnt.
I took it to repair shops and they said that the problem is the battery and ofc to no suprise, they dont have a replacement.
Do you guys have any idea what happened? Was it a button issue, software issue or indeed battery issue. Before all this happened, the device was working perfectly.
Please help. I miss my phone already.
I think it due socket of battery, can you open the back cover and plugout and plugin this socket, will be OK

Categories

Resources