Unable to boot Qtek 9100/SPV M3000/HTC Wizard - 8125, K-JAM, P4300, MDA Vario General

hello everyone,
I recently bought a locked Qtek 9100 (SPV M3000/HTC Wizard) and I was trying to unlock it using lokiwiz v0.2. It went through all the steps without any problem, but one... it was still sim locked!
Maybe because my phone is a new version, as it had Feb 06 as its original date... I don't really have any clue.
As this didn't work, I tried to find out in Google if I could find any unlocking code, even if I had to pay 30 euros for it, as that free tool didn't work it out for me.
I used www.gsmliberty.net, paid for it, followed all their instructions - again, everything went perfect - and in the end... ... my phone is not working anymore!... It doesn't even get to the Windows Mobile Logo...
It shows HTC logo and the provider logo, but then reboots and keeps going on this cycle as long as the battery lasts.
I've tried to hard reset, but it stays all the same! I do everything as I have found out in every forum that has some information about it, and it still can't get out of this rebooting cycle...
Can anyone help me on this?
I fear that it had some kind of advanced protection against known unlocking tools and now its ruined for good
Please tell me that we can work this out! The phone was working perfectly before, when I inserted a SIM card that it allowed (from the phone's provider...)
Any help will be most welcome!
Cheers

Sorry to hear of your problems. Please tell me the details of the rom including the ipl and spl numbers. Is the rom a qtek one? - your post is confusing.
I would try reflashing the device with the original rom as the format has failed to do anything.
Download rom from here ftp://[email protected]/Wizard/Roms/Qtek/ password is xda.
To get to the bootloader screen to do this, turn off your device then press and hold camera button and then power on. You should then reach the multicolored bootloader screen. Connect to pc using usb cable and you should see usb in bottom left of screen. (the device does not need to be activesynced to flash rom) then start exe on pc and the device will reflash.

meschle said:
Sorry to hear of your problems. Please tell me the details of the rom including the ipl and spl numbers. Is the rom a qtek one? - your post is confusing.
I would try reflashing the device with the original rom as the format has failed to do anything.
Download rom from here ftp://[email protected]/Wizard/Roms/Qtek/ password is xda.
To get to the bootloader screen to do this, turn off your device then press and hold camera button and then power on. You should then reach the multicolored bootloader screen. Connect to pc using usb cable and you should see usb in bottom left of screen. (the device does not need to be activesynced to flash rom) then start exe on pc and the device will reflash.
Click to expand...
Click to collapse
Thank you for your help!
My ROM version is: 2.18.7.2 PTG (15 FeB 06)
IPL: 2.18
SPL: 2.18
I also have this numbers, which I wrote down before the phone got ruined...
Radio Version: 02.10.10
Protocol Version: 413.1.03
ExtROM: 2.18.7.9161
Which of the files in that FTP should I download?...

Looks like your rom is portugese so this will be the one
ftp://[email protected]/Wi...digy_2180702_21807102_20710_QTEK_PTG_Ship.exe

Perfect! Didn't want to do anything wrong this time.
I'll do it tonight, when I get home. Hopefully this will turn it around for me...
I'll let you know.

The least I can do is to say THANK YOU!
You have no idea of how much you can to to make the world a better place.
Thank you so much!
If there's anything I can help this forum in, please do let me know, I'll be glad if I can somehow pay back this enormous piece of advice.

hveiga said:
The least I can do is to say THANK YOU!
You have no idea of how much you can to to make the world a better place.
Thank you so much!
If there's anything I can help this forum in, please do let me know, I'll be glad if I can somehow pay back this enormous piece of advice.
Click to expand...
Click to collapse
No problem glad you got it sorted. I like to help (this is what this FORUM is for) and would hope that it does make a difference. Best way you can help is learn, learn, learn and then help, help, help others. The helpers in the forum seem to come and go so i suppose there is a shortage, most come for info and advice. I enjoy posting helps me relax lol thats why i have over 1000 posts - must be well chilled out by now :wink:
btw do other sims work in your device now - if not ask for your money back!

dun know
hi guys i need help here i'm using spv m3000 with french langueage
i did follow as what told in this part (Download rom from here ftp://[email protected]/Wizard/Roms/Qtek/ password is xda.
To get to the bootloader screen to do this, turn off your device then press and hold camera button and then power on. You should then reach the multicolored bootloader screen. Connect to pc using usb cable and you should see usb in bottom left of screen. (the device does not need to be activesynced to flash rom) then start exe on pc and the device will reflash.)
one thing i dun get is what is exe and where to find please help me
my ipl is 1.03
spl 1.03.0000
os 1.3.1.4

exe is the RUU (RomUpdate Utility) icon in the Rom you downloaded,just run the RUU,it'll start to flash.

hi thanks for ur info i did try to flah the rom ruu but it cannot
flash the rom is there anything else i forget to do /
i did follow all the instrution where i can get the upgrade rom for french version for this pda phone
btw i'm using window vista

chanra said:
hi thanks for ur info i did try to flah the rom ruu but it cannot
flash the rom is there anything else i forget to do /
i did follow all the instrution where i can get the upgrade rom for french version for this pda phone
btw i'm using window vista
Click to expand...
Click to collapse
Vista is still not compatible for flashing,use winXP,its highly recommended and doen't give any problems.

hi thanks alot for info
i did flash wt english rom i use as what u told ( winxp)
thanks alot i wont forget ur help
(zabardast_1)

chanra said:
hi thanks alot for info
i did flash wt english rom i use as what u told ( winxp)
thanks alot i wont forget ur help
(zabardast_1)
Click to expand...
Click to collapse
Thanz!
It was my pleasure to help you,glad you got it working

I have problem n unlocking M3000
I have problem in unlocking SPV M3000.
IPL 2.16
SPL 2.16

meschle said:
Looks like your rom is portugese so this will be the one
ftp://[email protected]/Wi...digy_2180702_21807102_20710_QTEK_PTG_Ship.exe
Click to expand...
Click to collapse
i try to download from link but ask for FTP pass !? what is ?

Hi am new here,
can i updat my device ?
i like to improve the GUI of my pocket pc ,ist possible?
now my device running wm 5 ,can i updat for wm 6?
my device is Qtek wizard200
and more as follows.
suggest me ...thank u
22/09/09 12:02:51
CPU: Texas Instruments - OMAP850
MODEL: Wizard
IMEI: .................
=> Bootloaders:
IPL: 2.18.0001 (G4 device)
SPL: 2.18.0001 (G4 device)
Built on Feb 14 2006 at 18:47:41
Copyright (c) 2003 High Tech Computer Corporation
=> Firmware:
OS: 5.1.xxx (Build 14955.2.3.0)
ROM: 2.26
Registry AKU: .2.3.0
Radio: 02.25.11
Protocol: 4.1.13.12
=>Extended_ROM:
Version: 2.26.10.105
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
8fb7d682 - 60.63M (0x3ca0000)
ee9e4266 - 9.99M (0x9fd800)
4ea9d13a - 43.24M (0x2b3e000)
cfb25f96 - 50.95M (0x32f4000)
4fb25f42 - 2.94M (0x2f0000)
0fb25fba - 3.06M (0x30fc00)
=> DOC chip unique ID:
00000000813902052e1c1780140406da
Key Index: 82

qtek wizard upadting
Hi am new here,
can i updat my device ?
i like to improve the GUI of my pocket pc ,ist possible?
now my device running wm 5 ,can i updat for wm 6?
my device is Qtek wizard200
and more as follows.
suggest me ...thank u
22/09/09 12:02:51
CPU: Texas Instruments - OMAP850
MODEL: Wizard
IMEI: .................
=> Bootloaders:
IPL: 2.18.0001 (G4 device)
SPL: 2.18.0001 (G4 device)
Built on Feb 14 2006 at 18:47:41
Copyright (c) 2003 High Tech Computer Corporation
=> Firmware:
OS: 5.1.xxx (Build 14955.2.3.0)
ROM: 2.26
Registry AKU: .2.3.0
Radio: 02.25.11
Protocol: 4.1.13.12
=>Extended_ROM:
Version: 2.26.10.105
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
8fb7d682 - 60.63M (0x3ca0000)
ee9e4266 - 9.99M (0x9fd800)
4ea9d13a - 43.24M (0x2b3e000)
cfb25f96 - 50.95M (0x32f4000)
4fb25f42 - 2.94M (0x2f0000)
0fb25fba - 3.06M (0x30fc00)
=> DOC chip unique ID:
00000000813902052e1c1780140406da
Key Index: 82

Related

New MDA - Unlocking not working

Hi All.
I've tried everything, well, almost but at least a lot... and my new MDA won't seem to unlock!!!
Here is the data:
ROM versie: 2.21.2.5 NLD
ROM datum: 3/9/06
Radioversie: 02.19.11
Protocolversie: 4.1.13.09
ExtROM versie: 2.21.2.108
Modelnr: WIZA200
Seems to be fairly new, haven't seen this version around on the forum.
What do I need to do?
Error message that I'm getting while unlocking:
ERROR: ITWriteDisk - An internal error occured
Please help!!! I would like to have my MDA unlocked!!!!
Cheers.
SignorE
for those of you having problems with lockiwiz 3a not unlocking your phone, well i was having the same problem, but not for long because i discoverd what i was doing wrong.
when you download lokiwiz 3a you have 2 things, lockiwiz and a folder called utils, now in the folder utils you will find a file called enablerapi its about 70kb in size, copy this to your MDA vario in the my documents folder, once there run it by tapping on it in my documents on your MDA saying Ok to everything, once youve done that, then and only then try running the lockiwiz application on your main pc making sure your connected via ActiveSync and look for the SIM unlock code in the black command promt box and jot this number down, then put SIM card in thats different from the one you use and switch on, when asked for the unlock code just type in the number you jotted down and bobs your uncle!!! well he was for me thats is.....good luck. :lol:
mda charmer
MDA
CALLED CHARMER WITH CHIP G3 G4 WILL NOT WORK
MDA
CALLED CHARMER WITH CHIP G3 G4 WILL NOT WORK
Click to expand...
Click to collapse
@chiragp: are you saying i cannot ulock my mda?!?! :'(
cheers.
signorE
Szabika, HU
Wowww.
Million ThanX for any line!
It's Cool!
Nagyon köszönöm!
New Mda Vario - help unlocking
Total Summary
IPL Ver : 2.21.0001
SPL Ver : 2.21.0001
Model WIZA200
ROM : 2.21.2.6 WWE
ROM Date : 03/09/06
Radio Version (GSM): 02.19.11
Protocol Ver : 4.1.13.09
Ext ROM : 2.21.2.109
OS : 2.24.2.6
Flash Chip type : M systems
--
With some reading I think my Vario is G4 --- Is that correct ....
Can I use lokiwizMSL 0.3a to unlock it...

Problem with Wizard ...

Hi to all. I'm a new person in this fantastic forum. Before yesterday i'm just visiting and reading, but now i need your help
So, I have a Wizard with T-mobile logo on it. Display has been changed, 'cause the original was broken. New display has been buyed from *-bay. Both displays are the same. When put the new display in the Wizard, everything looks fine, except the 8-bit color on the skreen ;( . Last night i read and make step by step things in this Thread: http://forum.xda-developers.com/showthread.php?t=298613 , but i need to stop on step G3.4 - i have a success update from step G3.3 with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE, but when i start the Wizard_Love_2.26.10.2_WWE_Novii_CF2, there is an error - 206 (on italian).
After that, i have read the http://forum.xda-developers.com/showthread.php?t=285435 thread, and started again... First update has been successfull (maybe), the Wizard started with Winmobile 5 (WM6 has been installed before starting updates).
That's the specs:
ipl: 1.01
spl: 1.01
rom date 2/02/07
radio: 01.12.10
rom version: 6.0.0.0 wwe
protokol version: 4.0.13.23
extRom version: Empty Extended (before updating)
Now, after 1st update are:
ipl: 1.01
spl: 1.01
ROM:1.5.4.2 WWE
ROM date: 11/8/05
Radio: 01.12.10
Protocol version: 4.0.12.23
------------------------------------------------------------------------
And now... i haven't idea what to do to update IPL and SPL to version 2.xx
and to install WM6 (XDA Mobile 6 Release 3).
Else, I think that the screen has only 8bit color is not a software problem. I think it's from hardware (display).
Else, i have install ActiveSync, but the program did not find any Wizard attached to the computer..
For first update, i connect and started wizard in bootable mode (3 color display, with 'usb' icon down left...
After restart, when starts normally, AS 4.5 didn't find it...
Can somebody explain me in a few simple steps what to do...
Please..
I'm new in this sphere. Sorry for my bad english.
Have a nice weekend to all.
Here -> http://www.snimka.bg/album.php?album_id=234481 <- are 3 pictures from wizard. 8bit color loooooks very very badd
Lattante said:
Hi to all. I'm a new person in this fantastic forum. Before yesterday i'm just visiting and reading, but now i need your help
So, I have a Wizard with T-mobile logo on it. Display has been changed, 'cause the original was broken. New display has been buyed from *-bay. Both displays are the same. When put the new display in the Wizard, everything looks fine, except the 8-bit color on the skreen ;( . Last night i read and make step by step things in this Thread: http://forum.xda-developers.com/showthread.php?t=298613 , but i need to stop on step G3.4 - i have a success update from step G3.3 with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE, but when i start the Wizard_Love_2.26.10.2_WWE_Novii_CF2, there is an error - 206 (on italian).
After that, i have read the http://forum.xda-developers.com/showthread.php?t=285435 thread, and started again... First update has been successfull (maybe), the Wizard started with Winmobile 5 (WM6 has been installed before starting updates).
That's the specs:
ipl: 1.01
spl: 1.01
rom date 2/02/07
radio: 01.12.10
rom version: 6.0.0.0 wwe
protokol version: 4.0.13.23
extRom version: Empty Extended (before updating)
Now, after 1st update are:
ipl: 1.01
spl: 1.01
ROM:1.5.4.2 WWE
ROM date: 11/8/05
Radio: 01.12.10
Protocol version: 4.0.12.23
------------------------------------------------------------------------
And now... i haven't idea what to do to update IPL and SPL to version 2.xx
and to install WM6 (XDA Mobile 6 Release 3).
Else, I think that the screen has only 8bit color is not a software problem. I think it's from hardware (display).
Else, i have install ActiveSync, but the program did not find any Wizard attached to the computer..
For first update, i connect and started wizard in bootable mode (3 color display, with 'usb' icon down left...
After restart, when starts normally, AS 4.5 didn't find it...
Can somebody explain me in a few simple steps what to do...
Please..
I'm new in this sphere. Sorry for my bad english.
Have a nice weekend to all.
Here -> http://www.snimka.bg/album.php?album_id=234481 <- are 3 pictures from wizard. 8bit color loooooks very very badd
Click to expand...
Click to collapse
You have downgraded your phone to IPL/SPL 1.xx by flashing Button's Rom 1.05.there's no need to flash wizard_love_Rom,instead download and apply lokiwiz02b tool to SIM/CID unlock the phone and then download T-mobile 2.26 and flash to upgrade to IPL/SPL 2.xx for upgrading to wm6.The above guide was written quite a while ago,its better you follow the most updated guide as in the link below:-
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Thanks a lot zabardast_1, but I have 1 problem - Activesync didn't find any Pocket, attached to the computer, so i can't make the steps in the tutorial.. the pocket is SIM unlocked.
Lattante said:
Thanks a lot zabardast_1, but I have 1 problem - Activesync didn't find any Pocket, attached to the computer, so i can't make the steps in the tutorial.. the pocket is SIM unlocked.
Click to expand...
Click to collapse
Is your phone working normal,does it load up to OS ? to check the connectivity,get the phone into bootloaders(tricolor screen) connect via usb cable and check if usb appears at the bottom of the bootloaders,if not then there's a connectivity problem,either with usb cable or the mini usb port of the phone.
if the phone works normal and loads OS,then you can even try to use lokiwiz02b or WST tool via BT and CID unlock the phone.
It's normal working, like I said in my 1st post - 8bit color. I think it's from OS, but i'm not sure - i have downgrade form WM6 to WM5, and the problem is still here .
In bootload mode have indication for USB - bottom left on the screen, the battery has charging, but ActiveSync still don't want to find my Wizard..
P.S. Pfffff, I decline to fight with that.... Monday i'll test with other USB cable. Even it charging battery, i think ActiveSync can't recognize the Wizard, because USB cable is failed somewhere,...
I don't know what i think.. I'm tired.... Good night..
If its working normal and it establishes connectivity through usb as it appears in the bootloaders,then,its the AS software,which is not detecting.Assuming you are using winXP,Delete all partnerships/profiles in the settings of the AS or Uninstall As and download the latest version 4.5 and install it,close any Antivirus/Firewall or any other software which might be hindering with AS and let it again activesync.Also remember to uncheck 'Enable advanced network functionality' in the settings...> connections...> usb to pc options in your phone.
Hello again. I try to install 3 versions of AS, but the result is the same - No Connection. reset the wizard 3 times, stop all running software - ICQ, Skype, antivirus, browser... no and no.
When AS looking for device, there is 7 8 COM ports, Infrared (no installed), USB available, but AS can't find my bluetooth...
I have install bluetooth, and make connection with the wizard, but i can't unlock with lokiwiz02b-HTC Unlocker.
Better try on other winXP based pc
I think so, tommorow at work zabardast_1 thanks a lot man.

Help - newbie wants to upgrade

Hi all.
I start by contemplating the fact that there are quite some portuguese members arround.
Força Portugal
I just got hold of a O2 Xda Orbit. It has windows mobile in english and I want to put it in portuguese.
I don't know how
I have been reading about the ROM's in portuguese but I am afraid of just upgrading without knowing what I am doing.
That is why I am now requesting you guys to point me in the right direction
Device Information:
ROM Version: 3.4.206.2 WWE
ROM Date: 4/18/2007
Radio Version: 02.67.90
Protocol Version: 4.1.13.28
-
Also I don't have (yet) ActiveSync installed on my computer... do I need it?
thank you in advance...
Tiago Geada
cusco
Brief step by step plan
vigaro said:
Hi all.
<question>
ROM Version: 3.4.206.2 WWE
ROM Date: 4/18/2007
Radio Version: 02.67.90
Protocol Version: 4.1.13.28
Also I don't have (yet) ActiveSync installed on my computer... do I need it?
cusco
Click to expand...
Click to collapse
You do need ActiveSync for XP or older, or Windows Mobile Device Center for Vista (download the latest version from Microsoft).
In general you have to do the following steps:
1. Connect your Artemis to the computer using a USB cable.
2. Do NOT make a partnership. If you get a wizard or popup, just cancel/quit it.
3. obtain the rom of your choice (it sounds like you've allready found a PTG rom)
4. make sure your Artemis is CID unlocked. If not, use artemis USPL for this.
5. run RUU.exe or RomUpdateUtility.exe which is usually provided with the rom. If not, find a recent version HERE. If you use a RUU.exe not provided with your rom, just remove the old rom (a large file with the extension .nbh) and put your rom in the folder with RUU.exe
6. Follow steps on the screen. Read the information / caution rules, press next a few times, then press update.
7. The Artemis will go into boot loader mode (first a three color screen, then a grey one with a white/blue progress bar)
8. wait some time, until the wizard says you're finished
9. The Artemis will reboot. Wait for it to completely start windows, then do a hard reset (push both softkeys and the reset button, release reset button after a few seconds). This way you make sure your rom gets flashed well
10. Wait for the progress bar to end again and for windows to start
11. Start calibrating your screen and customising windows to your needs.
This should do it

Am I missing a step?

I'm kinda of a newbie to the whole flashing the HTC 8125...I've searched and searched and downloaded a couple of ROMS that I would find pretty cool on my phone but...whats next? I got a Cingular 8125...I did the hardSPL..and heres what I got...
Wizard Service Tool v4.2.2
18/02/09 02:08:43
CPU: Texas Instruments - OMAP850
MODEL: Wizard
IMEI: ----------
=> Bootloaders:
IPL: 2.21.0001 (G4 device)
SPL: 2.21.Olip (G4 device w/ HardSPL)
Built on Aug 26 2007 at 19:41:34
Copyright (c) 2007 Olipro & HTC - Hard-SPL
=> Firmware:
OS: 5.1.xxx (Build 14928.2.2.0)
ROM: 2.25
Registry AKU: .2.2.0
Radio: 02.25.11
Protocol: 4.1.13.12
=>Extended_ROM:
Version: 2.25.11.102
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
ee9df2f2 - 5.00M (0x4fec00)
6ea9d13a - 48.23M (0x303c000)
0fb25f92 - 50.95M (0x32f4000)
0fb25f3e - 2.94M (0x2f0000)
2fb25fb6 - 3.06M (0x30fc00)
=> DOC chip unique ID:
00000000306901051024050918060635
Key Index: 84
All Done.
I still got WB5 on my phone..and I tried TNT.1933 touchflo..by hooking up my phone with a usb and activesync..but when I ran the RUU it said file error..do I have to upgrade to WB 6.1 first and if so...where do I get it (ive searched wiki and everything I could search here) or am I missing a step? Any help would be great, thanks!
need help?
hi there.... it seems you have unlocjed the device...
now, when you try to upload a new ROM. first of all, the device must be "connected to PC" using activesync (v 4.5)
then u have to run RUU.... in fact most roms you download have the RUU inside... so send me message if need help... send message...
GOOD LUCK
Nothings wrong there and you don't have to upgrade first to any rom,All the wm6 or wm6.1 roms can be flashed directly,as its already HardSPL,you can flash any wm6 or wm6.1 roms as much as you like,but just don't flash any official stock rom,it contains IPL/SPL,it'll Brick the phone.
If its a 'File Open' or 'File Read' error,re download the rom package again and run it,it may be the rom you downloaded is corrupt or missing some files.

[HTC Blue Angel] Windows Mobile 6.1 WWE by Ham3r

Windows Mobile 6.1 WWE by Ham3r
final version!
Windows Mobile 6.1 (build: 21042.1.6.1)
OS: WM6.1 WWE
Free RAM after SR: ~105 MB.
Screen's:
Software:
- ArcSoft MMS 5,
- 1-Calc,
- Jbed,
- FileExplorerEx,
- full Office (without ppt),
- Network Wizard,
- Comm Manager
- SIM Manager from Iolite.
After flash:
After flash, please make HR. After align screen, run ExtROM, please make SR!
Download:
- 4shared
Please don't make mirrors!
hi
good work,nice to see a new developer here,for me i prefere wm 6.5, thnx and good work.
Plain???
Is this so vanilla isnt it?
Yes as homan say, welcome a new developer on Blueangel...
Keep it up!
+ Que PPC said:
Is this so vanilla isnt it?
Yes as homan say, welcome a new developer on Blueangel...
Keep it up!
Click to expand...
Click to collapse
Yes, is it Vanilla, but with useful, standard apps (Java, MMS, Calc). i cooking new WWE ROM, no vanilla, but Vanilla Creamy (more software)
hi, i am new flashig my SPV M2000, Could you tell me how to fix my phone???, I ran your software(hamer 10) and i turned it off(yes, i know!!!), now i only get "serial/usb v2.06", and when i push on/off, record and reset buttoms nothing happen. Could you help me???
sorry, i don't understand.. maybe reflash rom?
flash it in windows xp
Thank you very much!!
at last, ham3r, at last you decided to share your product here.
good idea.
guys, he is good rommaker(he made great roms for wizard, too).
downloaded this rom, today will test it on ba
managed to restore my bricked BA, had to use vista32 bit, the given drivers for BA and this rom by ham3r.
Mm, current I'm using a manila2D on it, works well.
Btw, any ideas on how to make the start menu of the WM6.1 change it colors? I prefer black, matching with the manila2D darkness.
Noted and thanks!
What does this mean ?
Sorry for the display of my ignorance, but I do not know what the following means -
>After flash:
>After flash, please make HR. After align screen, >run ExtROM, please make SR!
What do I have to do, please. I know about aligning sreen, but "make HR" and "run ExtROM, please make SR !" does not mean anything to me.
Thank you for your help
HR = Hard Reset (Push Camera Button + Voice Record and Resetbutton. Change the values KILT = NO, the rest yes. Change the values with die Voicerecord and Camerabutton. When finish Press the Mailbutton
ExtRom= Mostly runs automati when this folder is on your storage card, there are some extra programs for windows.
SR = Softreset (Press the reset Button with the Stylus)
Problem with HTC Touch mobile signals
Hello,
I have HTC Touch here are the details of my model. I am facing problem with mobile signal. Give me some solution for this.
lVersion ROM
Version 3.07.720.03 WWE
ROM Date 10/25/2008
Radio Version 03.34.90
Protocol Version 4.1.13.71
Hardware CPU OMAP850
Speed 201 MGz
RAM size 128 MB
Flash Size 256 MB
Data Bus 16 bits
Storage size 110.30 Mb
Display 240X320
Colors 65536
Bluethooth Version 2.0
Bluethooth Address 00:17:E896:89:7B
Identity Model No: ELF0100
Thanks,
Purushoth
hi,this thread for HTC Blue Angel only.
how do i bypass the country code error?
every wm 5 & 6 rom i tried still gives me the error...
please help me fix it!
Why don't you applied patch for certs?
Thanks for the posting and files...
HTC BA - PH20B1 (Siemens SX66 for cingular USA)
Please help...
I was able to update to 6.1 but stuck at the end
1. Did not get the screen alighnment option.
2. Screen alignment is missing, not able to click properly
3. Not able to see the programs
3. WIFI is not working
4. Sync is not working
5. Not able to run EXTROM
I appreciate your prompt response.
Thanks!
Ham3r said:
Windows Mobile 6.1 WWE by Ham3r
final version!
Windows Mobile 6.1 (build: 21042.1.6.1)
OS: WM6.1 WWE
Free RAM after SR: ~105 MB.
Screen's:
Software:
- ArcSoft MMS 5,
- 1-Calc,
- Jbed,
- FileExplorerEx,
- full Office (without ppt),
- Network Wizard,
- Comm Manager
- SIM Manager from Iolite.
After flash:
After flash, please make HR. After align screen, run ExtROM, please make SR!
Download:
- 4shared
Please don't make mirrors!
Click to expand...
Click to collapse
always make hardreset after flashing
press camera+record+reset during some seconds
in the open menu keep 1st line at no and select yes for 2nd and 3th lines
record change line and camera change yes/no
after that click mail button
if your mail button don't work (broken or something) use multi-port tty 1.42
search more info at forum

Categories

Resources