Related
Hello,
because my posting in this forum wasn'n answered i tried to fix together with Mr. Wolf from Wolfsoft (www.wolfsoft.de - also great for fast XDA RAM-Upgrades) with the informations i found.
Everytime i write the i did something - i mean - we did it! We worked hard together for this solution.
-----------------
First:
Maybe, surely you can destroy you XDA-ROM more than it was destroyed before. I not guarrante or take responibility for any errors or damages occuring while trying the next steps.
Situation:
I upgraded my german O2-XDA in the wrong way. After this I had the following problem:
- The O2-bubbles appearing after soft- or hard resetting the XDA are displayed for 3 or 4 minutes. In the right bottom corner of the display the Version of WinCE ist dissplayed (3.14), after some times someting more was shown but that seemes to be from a crashed source.
- After the "pling" a white screen with a blue bar on the top is displayed. The screen-light doensn't turn off. Nothing more happened, after 20 or 30 Minutes the XDA performs a soft reset automatically - after this the same problems occuring
Requrements I needed to fix my problem:
- 1 (better 2 SD-Cards with minimum 32MB Capacity)
- XDA Cradle connected to the PC and Power
- in some cases 1 Charging cable (USB or Power) with a connector for the XDA
- The Program A and Program B - Files provided by german O2 website
- The repair.zip-File provided by XDA-Developers
- A second XDA or a SD-Card-Reader connected with your PC
- many time
- Your XDA must have a working bootloader (mine was Version 5.15), try it by holding the Power-button while performing a soft-reset.
What I did:
- After entering the Wallaby-Bootloader an "gsm-error" - message appears after 1 minute of "wait"
- I entered the SD-Card-Menu by pressing the Contacts-Button on the left-top of the XDA
- I choosed Write CE to SD in order to save my original CE in order to avoid unuseful Questions in case of repair-fail by O2-Support
- After this I performed a soft reset an waited for 1 or 2 Minutes after the white screen appeared
- While tis time write the contents of the unzipped repair.zip to the SD-Card using the SD-Card-Reader or the second XDA
- Now i pressed the "Volume" - Button on the left side for many times, after some trys (if it is not working perform a soft reset and try new) I saw a non-working Today-Screen
- Now insert the SD-Card on you have written the files from repair.zip
- There are 2 possibel reactions:
First: You get a message to format your SD - DO NOT!!!! In this case remove your SD-Card, connect your XDA with the Charging Cable and perform a soft reset. It is okay that there is no charging light. After you entered the Today-Screen insert the SD - do not remove the Charging-Cable! Then it will work.
Second: Installing beginns without any problems
Now your Radio Stack-Module will beginn to be updated. In my case I got the 1% Error discussed in the forum.
- Remove the Power cable, connect your cradle with the PC and the Power, perform a soft reset and wait what is happening. After the error occurs don't push the ok-button. Simply press the start-tab (or anywhere other excluding the message). Now take the XDA out of the cradle and after this put it in again, still with the error message on the screen. Now an active sync connection will be shown on both, your XDA and the PC! If you have this case, it looks good.
- If this doesn't work, replace the RSUpgrade.sa.cab-File from the repair.zip with the same named File, whats included in the program_B.exe (extract first, you will find the result in <Harddisk-Device:\Programme\Programm B) and writhe both on your SD
- Soft reset the XDA, ignore all errors, do not put the new written SD-Card in - open the Active sync-connection and delete the both newest files in the Windows-Directory of your XDA. If you can't delete, rename the file. After this perform a new soft reset.
- You will get a "file not found error". Try to temove and insert your XDA in the cradle to get an active sync-cennection. If this doesn't work insert the new written SD
- Try new flashing again again, maybe it works. If not try to push on the screen and remove and reinsert your XDA in the cradle to get a Connection.
- If there is no possibility to get a connection - i do not know any futher solutions - sorry.
If you get the connection, perform the normal Flashing with Program A provided by your Provider. After this is successfully completed you will see the loading-LED again! Congratulations!
If this is completed charge your Battery to at least 70% - be patient, it will take up to 1 Hour!
After this perform Programm B provided by your Provider. If this successfully completes - Congratulations - you are up and running!
I don't know, if I had happy circumstances, but this worked to gat my working XDA back!
If it do not work, use the first SD-Card containing your old CE to copy back your old ROM in order to not loose your support by your Provider. Simply insert the card into your XDA and perform a soft-reset while holding the Power-Button. Everything looks broken but original!
Please feedback in the XDA-Forum-Thread, if it worked at your XDA or if you have any hints for improvements this steps. Thank you!
Best regards from Berlin/Germany to all XDA-Fans like I am!
Miwu
Very detail.....thanks a lot ! :lol:
Tried your solution but i don't know which files i should delete cause when i delete the latest two files i get no error message...
When trying to install Programm a anywway i get a Connect Power Message and the installation stops.
Edit:
I managed to get the file not found error by renaming the RsUpgrade executable but still get the Power Adapter not plugged in Error...
So it would be very important to know which Programm A you used.
Hello,
@ianrush
Have you been able to get an active sync connection as I described?
You have to delete the file causing the Radio-Stack-Update after restart, I think they are located in the Windows directory of your XDA. If you let your XDA order the files by date the 2 newest files are the ones for updating the Radio Stack and causing the 1%-error. In deleting these files you can get your XDA booting without starting the gsm and getting the Active-Sync-connection. To break up the Installation you must delete these files (i remenber that on (the one that must be renamed) was only 35k or in this area, the other one was much larger).
After deleting and restarting by soft reset you don´t get the 1%-error-message, but another one like "The file can´t be found). But if you see this message (do not press okay!!!!!) you can use your Active-Sync-Connection to flash with Programm A and after this programm B.
The files (germen version) are located here.
Klick at the link "Download Software-Update" and accept the conditions by clicking "Akzeptieren". After this a new window is displayed for downloading the Software. The versions are:
CE: Version 3.19.01 -
Radio Stack Version 4.21
"Teil 1" means Programm A
"Teil 2" means Programm B.
Remember, it is the german version with some german specials like the "Homezone". But you can turn it off and while I see, that you are from Austria, I think you won´t have any problem with the language...
Isn´t it very strange, that 2 german speaking people trying find solutions in english??? :?
Best regards from Berlin!
Michael
I have no problem starting an Active Sync Connection, my problem is, that i get this odd Error Message which tells me to plug in the Power Adapter, which is obviously connected...
There is a much easier way of getting rid of the Flash Prog bei simply deleting the RsUpgrade link in the Auto Start Folder in the wwindows directory and its also possible to start an Connection via AS.
My real problem is the battery charge check before the real flashing of the RSU.
I tried it with the mentioned O2 files and also with Tmobile.at/de files.
A solution may be to "crack" the installation file or to write a small prog wich tells PPC that the battery is chraged.
Many thanks for your help, but it didnt solve the problem for me.
PS: Well its an English Forum so i think we should stay in that language
Oh, I forgot to write that one.
The charging light, wich may be an indicator for the XDA-OS for the supplied Power came back as we installed the O2 Radio Stack via the Active Sync-Connection bevor performing Programm A - Upgrade. Try to perform Program B - Update first, in our case we got our lovely orange light back and then performed the Programm A and Programm B - Update again!
Regards again!
Michael
Didn't work for me either.
The BIG question is how the hell did you get your XDA charging his battery again ? I believe that this will help many people to get their 1% Flash failed problem solved.
Hi !
I will try this method tomorrow.
Sebi
Hello,
I do not know why, but after (failed) installing Programm B after connecting via Active Sync first it worked . Maybe because of the working version-combination of Radio Stack and CE.
Regards
Miwu
@Sebi Please post if it is working!
Hi !
Don't work for me.
My problem is same this:
Posted: Fri Aug 29, 2003 19:26 Post subject:
--------------------------------------------------------------------------------
I have no problem starting an Active Sync Connection, my problem is, that i get this odd Error Message which tells me to plug in the Power Adapter, which is obviously connected...
Click to expand...
Click to collapse
Best regards
Sebi
miwu
I followed your steps and got the following message on my device:
The file "\Windows\RSUpgrade.exe" is in use or is in ROM. If the file is not in ROM, please close the application using the file.
Please advise
Anaq8i,
if this messege appears then rename the file "\Windows\RSUpgrade.exe" with an new name like "\Windows\RSUpgrade_used.exe" restart the device and follow the further instructions.
Hope that helps
Regards
Michael
miwu,
I cannot rename it, nor can I delete it, I think because it is in ROM. Please keep in mide that the I have not closed the error message after the 1% halt.
I reached the point were I can access my device and can sync with my PC. If I try the Programme A install, I get the message " WARNING 001: POWER ADAPTER NOT PLUGGED IN, Please plug the power adapter into your Pocket PC". Every time I try the RSU upgrade I get the 1 % error. Any suggestions will be appreciated
Hi anaq8i,
please try to rename the file by using the Active-Sync-Connection an the Explorer of your big Desktop-PC. The file cannot be in the rom, it is located in the ram of your device in order to get deleted after upgrading. Try to rename the file this way, then perform a soft-reset (not a hard one) then you will get an error-message that sonds like "the file ... cannot be fount", then put your device in the crade for active sync and try to install the original Programm B of your Provider (not the file from repair.zip). That worked at my XDA.
Please answer how it worked.
Regards this time from Hamburg/Germany
Michael
thanx a lot, have the same error, now all worx fine!
czeky thanks for answer. I am glad that my description was helpful Doe it work for other users?
@ czeky
would you also please be so kind and tell us if u tried any other steps than mentioned by miwu ?
If i treally worked with your XDA there you must have done something different then anaq8i, Sebi and i did...
miwu
I reached the point that I can boot my XDA and can sync with my PC. But I still cannot install /upgrade the RSU software, I still get the 1% error. If I try to install Porgramme A, I get the "POWER ADAPTER NOT PLUGGED IN" error message. I never reached the orange light stage on the XDA.
Anything else I should do?
@anaq81
Did you try to rename the described file via Active Sync? I posted it some day ago ...
Hi,
I was upgrading the software upgarde on my device. I successfully upgraded the Pocket PC software on the O2 XDA, but when I tried to upgrade the GSM radio/GPRS software of the O2 XDa, it gave some error and after this my device is not starting at all. The only mistake I did was that "I did not remove the SIM card before upgrading the GSM radio/GPRS software" The device does not start even after cold booting the same. When I start the device, the O2 screen comes and after a quite long time the main window does come but I cannot do anything. I tried to tap on contacts, time, tasks but nothing happens. I can see the windows logo wall paper but cannot do anything. Please help on how I can restore back my O2 as a cold reset also does not work. :?
Thanks and Regards
Jinesh
There's many topics about your question in the forum. Search it! Try to search with this keywords: 1% error, repair.zip
There's many topics about your question in the forum. Search it! Try to search with this keywords: 1% error, repair.zip
Hi,
I have tried all the available options but it still does not work. To restore the ROM how do I get access to the O2 cause niether serial nor USB is detecting it.
Please help.
regards
Jinesh
SD card install guide
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
Click to expand...
Click to collapse
Thanks Chief, I will try out and let you know.
regards
Jinesh
Hi Rudegar,
I tried the procedure given by you. I was able to write to the flash successfully. After writing to the flash it gave a message "Checksum OK, Please cold reboot to reset".
I did a cold reboot. After starting the O2, it showed the O2 logo screen and after quite a long time, it asked me wether I want to format the SD card or not. After that it took me to the default screen of XDA wher eit showed options like "Add today's date, Contacts, Schedule etc etc. but upon tapping any of the options the O2 behaves erratically. If I tap on today's date it takes me somewhere else. Inshort it does not work.
I again did a cold reboot and now the device is in its original position i.e not going after the O2 logo where it gets stuck up.
One thing I would like to mention is that all these activities have been done putting the O2 on the cardle only as the battery is totally discharged and the device turns on only after putting it on cradle. Even after the cold reboot it does not start unless I put it on the cradle whichis connected to the mains. Is it Ok with this or am I doing something wrong? The battery does not charge and hence I have to do it in this way.
Please suggest what wrong am I doing? Any suggestions from anyone will be welcome.
regards
Jinesh
Hi,
Someone posted the original O2 ROM on this site and I downloaded the same after which I was partially succesful in flashing the ROM and reviving my dead O2 back to half life. :roll:
I burned the ROM on
to my SD Card and flashed the ROM on to my O2. After
successfully flashing the ROM I rebooted the device.
The device now starts Windows but it takes atleast 15
minutes to start. I get the today screen. WHen I cick
on start the start menu appears after a delay of 10
seconds and all applications run normal, however all
this happens only on the Cradle only.
When I go into the Battery Settings it shows "Battery
Status Unknown".
Also none of the phone functions work. The SIM card is
not recognized and in device information it does
dispaly the "IMEI number" and the "Protocl Version"
I am only able to use inbuilt phone applications.
Is there some problem with my battery cause it is not
charging even on the cradle.
Device Information does not show Radio Version, Protocl Version & IMEI number at all.
Can anyone please help me?
hello all,
it means that your radio stack are dead. Currently, We don't have any real method to fix this problem. When the radio stack is error, you can not upgrade it or do anything to make it work. We can only upgrade or downgrade the radio stack if it works. Also if you try to upgrade the radio stack, we realy need to flash the chip using a speceial tool or need the sd card which build in radio stack with we can only flash in bootloaading mode. Howerver, in some case, we can fix it but .... I think it is just lucky or the xda error when battery problem.... in this case, just disconnect the battery few minutes and connect it again by pressing the battery hole.
Regards,
Hoanghon
p.s. I have dead xda. I killed it when I upgraded the RADIO STACK. Therefore, if you are really need to upgrade the radio stack, I recommend use the official upgrade for secuirity. or just upgrade the rom only.
Note:
To eliminating the error, you need to upgrade the rom or the radio stack, you need to check if the rom fix the radio stack or the stack you are trying to upgrade it fix the rom or not.(ie, Tmobile Rom have to use it radio stack built for Tmobile pocket pc...... I know that in some case when we mix between the radio stack and OS it works but I don't think it work propertly. Anyhow the mixing bettween radio stack and OS is very dangerous if it doesn't suppport then you have to reflash the radio stack or rom(the OS is Okay but the keep upgrading the radio stack may cause the radio stack killed)
WE NEED SERIAL CABLE FOR PDA ANY HELP PLS!!!
Hi Jineshd we
have the same problem and we are sure that the only way is to do SD uptade
and U said U have a serial cable to Yours device. With that we can be able to download flash gsm rom from working device and put it back via SD card to ours. Pls tell me where can I get a serial cable or some schema how to prepare it and I will try to repair ours dead pdas. Its our only chance
rgds
Lukasz
Hi,
Thanks all for the replies.
Can anyone tell me how doI repair the radio stack?
Regards
Jinesh
no way without having special RSU rom update on SD card and run it from bootloader or dissembling the device and reprograming GSM rom on special rom/bios programing socket. (Here on forum is user Cgigate from Toronto CA who can do it but I cant contact him)
Hi, let me start off byapologising if this issue has been dealt with before but I am fairly new to the board and I am also a complete novice when it comes to these types of phones.
My problem is this. I have a T_Mobile USA PPC Wallaby, I live in England and I would like to unlock it so that I can use an O2 chip in it. I need an SID code to use the O2 chip which T-Mobile USA will not give to me because I do not have an account with them. I tried XDAunlock but it kept saying "Error getting unlock code". I tried to install "XDA-developers-SER-v12" but I kept getting the error message "ERROR: GetDeviceData - An existing connection was forcibly closed by the remote host.
error getting devicedata" and then "Cannot execute the remote communication program.
Please make sure the USB/Serial cable is properly connected". I also tried using "xdadev_all_unlock-v1.3" with no luck. In fact, all I have been able to do is downgrade the Radio Stack (whatever that does?)
My device is.....
ROM Version : 4.01.16
Radio Version : 4.21.00
Protocol Version : 32S54
Hardware Version : PW10B
I am using Activesync 3.8 with Xp Home installed on my desktop. If anyone has any insight into this please could you help me with it?
Many thanks.
As already told via PM:
You have to install the special Edition ROM via SD-Card since you´re actuell ROM-Version prohibits flashing via EXE-File....
Extract the Specialedition ROM EXE file with winzip. You get an directory English where the ROM (NK.nbf) is located.
Download XDATools ftp://xda:[email protected]/Wallaby/Tools/XDATools.zip
Extract them at any place and run osimagetool
Select the NK.nbf File in the Source drop down menu.
Select your SD card (disk drive) from Destination the drop down menu.
Select Copy to start writing process and the tool should start writing to the card.
When XDATools has finished writing the image (no Infomessage) put the SD-card into your device
If there comes a message to format the SD-card select No
Hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a " Hard Reset"
Stefan
Success!!!
Wow! Thanks Stefan, that actually worked and I now have the Special Edition Rom installed on my device! The only problem I have now is that I have no signal Do I need to upgrade my Radio Stack?
No, normally not.
You could try changing Bands in bootloader, but normaly it shoud work....
Code:
Changing radio bands on Wallaby using the Bootloader
This page describes how to change radio bands on a Wallaby phone using the bootloader. If you change to a band that is not supported by your phone, your radio will receive less signal than with the bands it was tuned for. I.e. if you have a 900/1800 phone (Model number on sticker printed on back says "PW10A" instead of "PW10B") then if you change to 1900 MHz your phone will not be tuned right. If your sticker on the back says PW10B, then using the 1800 band is likely to degrade signal quality.
Changing bands
1. Press and hold the power button on top of the device
2. Go to the bootloader by gently pressing and releasing the stylus in the largest of the two holes on the bottom of the device
3. Release the power button
4. Wait for the screen to say "GSM OK"
5. Press the 'calendar' button on the right above the screen
6. Select the GSM band of your choice from the menu using the rocker switch under the display
7. Press the center of the rocker switch to confirm
8. Perform a soft-reset by pressing and releasing the stylus in the large hole again, this time without holding the power switch
Is your device really unlocked?
Can you search manually for networks? Do you find any one?
Have you the possibility to try another SIM-card?
Stefan
Boo Hoo Hoo!
The good news is that I now know how to install new Roms using the method you provided, yay! But now I cant get any signal at all and it does not seem to be able to find any networks, boo.
Boo Hoo Hoo!
The good news is that I now know how to install new Roms using the method you provided, yay! But now I cant get any signal at all and it does not seem to be able to find any networks, boo.
?????????
Since messing with the Radio Stack I have been unavle to get asignal or even pick up any networks? And I dont seem to be able to upgrade it to what it was? The only Stacks I can get to work are the exe type from the ftp server here, the zip files ones dont seem to work for some reason, and I need 6.25 which is only available as a zip. Does anyone have 6.25 as an exe type?
Thank God!
Well, I must be a complete dunce. I managed to upgrade the Radio Stack back to 6.25.02 and thanks to the help from LumpiStefan (and the fact that he was very patient with my complete noviceness) I am able to use my O2 chip and my PPC is now a phone as well!
Same problem but cant get into bootloader!
any Ideas ?
Re: Same problem but cant get into bootloader!
HarryG said:
any Ideas ?
Click to expand...
Click to collapse
Whilst holding the power button in, press the stylus into the reset bugton then let go.
Ive dont that 100 times - noting!!! - Bootloader seems to be gone!
HarryG said:
Ive dont that 100 times - noting!!! - Bootloader seems to be gone!
Click to expand...
Click to collapse
Hmmm, I don't know how to fix that? I tell you what though, there is a user here called 'LumpiStefan' and he basically walked me through it. He knows his stuff, maybe if you asked him he would help?
install everthing
installed erthing looks great but it is still locked need help getting a error getting unlock code
Hi
I am new here and i have problem
When i turn on my qtek9000, i recieve message Serial V.100.
If i connect USB cable it displays USB instead of Serial.
This happened when i tried to do radio upgrade (through usb hub, sim and sd were also in phone...).
I have 1gb SD card and also card reader mounted in laptop, so transfering files should not be problem.
Can someone help me with step-by-step procedure how to make my qtek work back. I used a lot of search but i am even more confused....
I just remember that when qtek worked Radio was something like 1.0.3.1 and also WWE was writen somewhere....
Probably i should put rom to sd with ntrw (which wersion of both),.......
please help....
might be a dumb question on my part - but have you tried a reset (initially a soft one but then a hard one of course, if nothing else works...) ???
I mean you will at least be able to revert back to the condition 'out of the package'...
Hope everything works out!
jup.both things NOT HELPED
looks like you're stuck in the bootloader mode....
try flashing the rom & the radio rom once again by connecting it to your laptop's usb...
i guess something screwed up while you were upgraging your radio rom...and you'd need to redo it!
Best,
San
can you please write me a procedure?
You might want to check the following thread. Everything is well described.
Cheers
hrb
http://forum.xda-developers.com/viewtopic.php?t=32725
i am trying to download files but i get permission denied all the time
You mean you get an error when clicking this link ?
ftp://xdaupload:[email protected]/Universal
I don't understand that, it works perfectly well for me
Cheers
hrb
I have solved problem with Radio upgrade. I am in much better mood now. 8)
Anyway i have 4 more questions.
1.) I am using bluetooth car-instalation Parrot CK3100. I am wondering if is possible to transfer any other sound except telephone conversations to that device. When i had Nokia 9500 i was able to hear every single click,tone,...i made on phone also on car-instalation. I also heard nokia ringtone in car instalation.With qtek i am getting generic car-instalation ringing tone instead of phone ringing. Otherwise primary intention (hands free talking) works fine. I would like to have that to be able to hear voices from various GPS software.
2.) Since QTEK9000 is PDA and phone in single unit I would like to have in car GPS application "always on top". Like previously mentioned i can easily manage my calls with car-instalation. Therefore i would like to run Phone section in background or GPS applications on top.I hope you will understand what i would like to say
3.) I also need in-car holder for qtek. Do you have any reccomendations?
4.)
My settings:
R: 1.04.02
G: 42.37.P8
D: 1.13.64.WWE
Is that ok or should i upgrade?
Stuck in bootloader mode
Hi guys,
Got stuck in bootloader mode following an upgrade attempt. Tried to reflash radio using the files from the pload folder only to get an error saying it's for the wrong device - tried this several times with the same result.
any ideas?
Is there a binary and a tool I can just do a straight upload?
thanks
Re: Stuck in bootloader mode
Bauser_uk said:
Hi guys,
Got stuck in bootloader mode following an upgrade attempt. Tried to reflash radio using the files from the pload folder only to get an error saying it's for the wrong device - tried this several times with the same result.
any ideas?
Is there a binary and a tool I can just do a straight upload?
thanks
Click to expand...
Click to collapse
try it with this file -
1. put radio.nbf and the file attached below in the same folder and run the exe with ur device connected to usb in bootloader mode...
2. hope it flashes it
S
Thanks DreamTheater
Thanks for your help - unfortunately I got the same message, ie this rom is not meant for this device etc...
Will see O2 can do anything (who's that laughing...???) - was going to buy a new xda mini anyway...!
1. REMOVE your SD/MMC card.
2. Soft/hard reset.
3. Run the upgarde again.
Step 1 above solved my problem.
After I read http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
It says The WM6 does not work on PH20A2 (Harrier) (Audiovox PPC-6600 / PPC-6601 / XV6600)/ CDMA device! <-- that is my mistake
My mistake steps:
1. upgrade 2003 2nd edition to WM6 (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
2. use mytt <-- may not hurt (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
3. Do hard reset, format the PPC (stuck in white screen, then do soft reset. The PPC will ""NOT"" stop if I remove the battery for a few seconds and put battery back)
reflash
Have you tried re-flashing with the original ROM?
AbuGWM5 said:
Have you tried re-flashing with the original ROM?
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
You got to revert back to WM 2003 SE with your original OS.
April 1 said:
You got to revert back to WM 2003 SE with your original OS.
Click to expand...
Click to collapse
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
king2004c said:
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
Click to expand...
Click to collapse
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
rickwyatt said:
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
Click to expand...
Click to collapse
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
try to take out first SD Card and SIM CARD from your BA first before connect to your notebook/PC
king2004c said:
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
Click to expand...
Click to collapse
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
xplode said:
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
Click to expand...
Click to collapse
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
king2004c said:
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
Click to expand...
Click to collapse
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
April 1 said:
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
Click to expand...
Click to collapse
I have already find a CDMA rom. Now the only problem in my phone is bluetooth
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
xplode said:
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
Click to expand...
Click to collapse
So far, I can use the phone without any problem. Previously, I tried to upgrade my phone because I want to use bluetooth headset to listen music. That can only be done in WM5 or later. Now I reinstall my CDMA version of WM2003. I find out that the bluetooth does not work due to expire of lincese key. Does anyone have any suggestion how I can over come it? I just want my phone back to exact a few day ago. Thanks
thanks
lincese
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
meehaa said:
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
Click to expand...
Click to collapse
Thanks, but does not work on my PPC6600