my wizard battery won't charge.
i have tried another battery and another rom with no change.
wehn i plug in the sync cord, the izard reognizes that it is on external power but just won't charge the battery.
any ideas.
thanks
...try to find out, by measuring, if the ±5Volt DC is present on the pins on the inside of the ppc which is needed to charge the battery. Probably your charging circuit is busted and the ppc should brought back for repairs...
thanks for the response
what is ppc
where do i measure the voltage.
when i first connect the sync cable, it starts to charge for one or two seconds and then stops and reverts to a normal non charging screen.
thanks
PPC stands for Pocket PC
What you speak of, I had the same problem on my wizard.
My battery finally died and I couldnt re-vive my phone.
I bought a new battery off of ebay, put it in, plugged it into the charger that came with my phone, let it charge overnight and I havent had a charging problem yet.
My advice, as well as alot of others on this board, dont use any other charger other than the one that the phone came with. I know I wont be.
...inside your ppc,when you remove your battery, you'll see different connection pins which are normally connected to the battery. With power attached (and without battery) you measure between 2 pins at a time. WATCH OUT for shortcircuiting, be careful!!!. You can use an analog or digital voltagemeter. I don't know which pins, so you have to try it yourself.
You should measure ±5 Volt DC which's delivered by your adapter. If there's no power then your charging circuit is defect and you'll have to let it repair...
reading about a volt on the internal pins that connect to the battery.
so it's the charging circuit.
damn
I had the same problem twice with 2 different batteries. it seems if the batterie dies completely, the device can not recharge itself. something like a car, you need to have enough juice to start the car so you can recharge the battery.
I took 2 paper clips that i used to connect the charger directly to the battery( bypassing the phone). you need to be careful with that, make sure you connect the right battery pins. I left my battery like this for 15min, just enough to have aniough power to start the phone and continue the charging process regularly.
As mlarif said the battery can fail to charge if totally discharged. So if you are not absolutely certain your circuit is faulty there are at least two threads here describing how to butcher a usb cable to jump start the battery.
Sorry I can't remember the colours of the wires off the top of my head. But a search may find the relavent posts.
...you can also use a 9 VDC battery to give the ppc batteries a boost for a few seconds. But indeed be sure to use the right pins
(btw did you measure any VDC on the batteries..?)
Related
My Atom has been working excelent for more than 6 months.
The problem is that when I try to charge it through the AC or a USB it doesnt charge anymore, the orange light doesnt turn on and the symbol in the phone turns only for a few seconds fron the battery into a wall plug, but then nothing...
I took out the battery and then charge it and worked but only when the device is off completely not when it is on or on stand by...
What can I do?
I just made a self diagnostic and when it gets to the part of the USB/AC Charging it says battery 100% charged (it passes the test) and that is not true, battery is at 18% right know
Same...
I have the same issue where my battery always shows as 100% even when you use it to 1% its still shows 100% and then it just quit when it runs out. Damn weird.... Just happened today and I only had the Atom Exec for 2 months... Any input would be much appreciated. Thanks!
Resolved
It was faulty battery not reporting correct capacity & usage.
I had a similar problem with my Atom. It could not charge the device from USB at first, then it got worse and stopped to charge from wall outlet. What I found out was that the connection plate at mini-USB port of Atom was worn out slighlty. I solved the problem by forcing usb cable connector into a mini-USB port, so it went further a bit (half a millimeter) and now everything is Ok - no problems to charge from either USB cable or wall charger.
I had the same problem, and found out that one pin in the mini usb socket bent downwards, fixed it myself and now its working fine
ozamalloa said:
My Atom has been working excelent for more than 6 months.
The problem is that when I try to charge it through the AC or a USB it doesnt charge anymore, the orange light doesnt turn on and the symbol in the phone turns only for a few seconds fron the battery into a wall plug, but then nothing...
I took out the battery and then charge it and worked but only when the device is off completely not when it is on or on stand by...
What can I do?
Click to expand...
Click to collapse
Mate! You gotta bring it to the SC... Its the fuse. The charging loop gose through the fuse and since it doesn't charge - most likely its the fuse (yo can test it with the normal tester...) If its not the fuse, it can be either of two - UEM Chip (Universal Energy Managmnt) or your PA (power amp). You can test it by measuring the resistance on the very left contacts of the battery ON YOUR PHONE! If the resistance close to 1 - its PA...
Wouldn't recomend to replace it yourself... Go for repair centre.
It's going to be a loose USB connection...
I did it on mine a while back, you have to hit the patch cable fitting in vigorously to the unit, and then from that day forward, no problems with charging!
Clean battery + phone><batt contacts if that makes you happy (it made me reassured)
G
I recently left my Cingular 8125 in Bootloader mode over night, connected to my PC not knowing that it couldn't charge while in that mode. I woke up, and couldn't turn it on; I eventually found out that the battery couldn't charge while in Bootloader mode.
The only solutions that I've seen posted are to: (A) Get another charged battery, (B) Charge your battery in a working Wizard
Both solutions aren't possible for me at the moment... what I needed to know is if there is a way to charge using some funky wiring rig using standard AA batteries to power it for about 7-10min. or so.
Cut one end off an old usb cable. Then plug the usb cable into your computers usb port and touch the black wire to the (-) on the batt and the red wire to the (+) on the battery. It takes a few minutes, but the battery will charge. Then put the battery back in the phone and boot into the os. Then charge the phone as usual.
Jeff
You can jump some wires to your battery from a battery charger to get some power to your battery --- need 5.7 volts -- positive to positve, negative to negative but I would not recommend doing this. Your battery is a lithium Ion which takes a special charge. Take it to a Cingular Store and ask the clerk if they could just charge it up in another phone for a couple of hours. I'm sure they won't mind.
Lithium Ion batteries are fussy about how they are charged, so its best to do it in another phone or a charger made for your battery.
Cheers!
Thank you guys sooooooooooo much for the info.
You have no idea how important this is.
EDIT: I stripped the USB cable, the outer wire is silver and there is quite a bit of it... there are four wires encased in the middle: one black, one brown, one red, one orange... I do not know which wires to connect to the pads on the battery.
hi there.
shortly-i have this phone with no orig. usb cable and with no wall charger. it was friend of mine phone actualy. given to me with dead battery (i am not sure but i have trouwn it away long time ago)
first I did was to wait until friends of mine from china had sent to me 2 batteries compitable with the phone. what i discovered is that a normal ordinar usb cable cant charge the phone's battery it only can connect to the pc.
second what i did is this: i found my old charger from a very old panasonic cell phone and had a try to make the charging process with the simply contacting corresponding pinouts of the battery to the +&- of this same charger (somehow i dissasembled the plug of that charger and it became more "comfortable" to get in touch to the pinouts of the specific cingular's battery)
that unordinar way i did discovered that i can charge these batteries even not sure how much appropriate that other brand wall charger is. It seems its pretty much the same as a power characteristics.
Meanwhile (as i dont use this phone) i had some free time to search the net and to have better idea about that strange unordinar power charging matter with that model of a phone. The situation is that i cant find a place nearby me to buy a cheap usb and wall charger and become using this nice device finaly.
And also i dont want to buy these cable things before clearly understand why this happens ..
I did try also to charge this phone with a HTC brand wall charger but no sucsess again cause it seems this wall charger is for other htc phone (even same mini usb plug and same characteristics)
What i need is to have answers by someone very informed about that matter and let me know what exactly is the specific power charging matter (need explanations i mean) with this phone. If sharing some good ideas about how to remake others usb cable or wall charger for geting it work along for me in such a case , i will appreciate this very much
thanks
charge
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
no
no it doesnt work that way.
what i need is the simple answer : what is so special into the pinouts of htc cingular 8125 wall charger?
thats what i need only. Then I might figure out how to proceed
Thanks anyway
I don't know if anyone else has had trouble doing what I have done, but I've got the Cingular 8125 (HTC Wizard 100), which is also known as the HTC 8125.
1. I bought a car charger at a convenience store for $6 that had the mini-USB plug. It worked like a charm. Never any problem there.
2. I also bought a standard USB to mini-USB cable from the local computer store, because I had lost mine, and it also worked fine for both synchronization and for charging.
3. I bought a second wall charger, buying a standard mini-USB wall charger sold pretty much everywhere cellular phone chargers are sold. It's a common charging port, and this generic worked for me as well.
I'd be interested to hear if anyone has had problems with these types of devices not properly charging the unit.
Even my USB cable for my portable USB hard drive will power my unit.
EDIT: About your problem with it not charging. I had that problem about a year ago, when my battery got extremely old. It wouldn't charge even with the original charger. I just needed a new battery. The batteries get old and stop taking a charge after a certain amount of use. How long this takes depends on how heavily the batteries are used. They, like car batteries, do not last forever.
I had this problem when I had my wiz too. The battery died and drained, and my phone refused to charge it. I took it to an AT&T service center, and they had no clue what the problem was, and they wanted to issue me a replacement (it was a G4, I had a G3, I wasn't about to fiddle with that at the time.) So I asked to borrow a demo device they had there to fix it. I charged my battery on their demo device no problem, got it up to 3%, and finished charging it through my USB cable in the car socket.
It appears to be a sort of one-in-every-few-or-so type condition, but I got hit with it.
seems like noone can tell me if something special inside the mini-USB plug.
i realy cant charge. Very nice device, but i cant make it charging up whit cables.
guys, from up there, say that nothing special about the charging cables, but i trust what i see not what i read.
Perhaps there is a problem with your USB port on the device? USB charging has standards, and all devices that need power from a USB port have the same power pin configuration. Otherwise, they can't call it a USB connection. It would have to be called a proprietary connection, and they would have to change the plug size/dimensions and pins.
If there isn't a problem with your battery (which is the most likely source of your problem), then it may be a loose connection on your USB connector. This happens with a number of devices.
If a sync cable connects to the PC but will not charge the battery, then you definitely have an unusual pin detachment of some sort, or a bad battery.
thanks again..
for pity i was writing a lot to make my recent post and finaly it desapeared cause my session was left.. its funny in some case, but now i just dont want to repeat all what was intended to be posted
i give only the link where you might see why i was assuming that this is a kind of a special matter here with that htc 8125 charging
//pinouts.ru/CellularPhones-A-N/razrv3_charger_pinout.shtml
so, any more help will be appreciated a lot
thanks
SOLVED: HTC Wizard (Cingular 8125) Dead Battery Wont Charge
Dozzen said:
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
Click to expand...
Click to collapse
Hi - Too bad for the OP that asked questions but did not listen to this brilliant post.
I have confirmed that a variation of this method works perfectly! I have an old Cingular 8125 that I have been trying to charge for over a year using various USB chargers and NONE would charge the device.
The reason that this may happen is that the original charger has an output of 1 full amp which is much higher than most chargers. The voltage is the same but you need a charger that can handle such a strong current draw.
Nearly all USB chargers can only handle around 250milliamps - 500milliamps which is about half the power needed to breathe life into a fully discharged battery.
The best solution is to NEVER let the battery fully discharge.
Here are the details of what I did:
1. Find the best match charger of 5-6 DC Volts and ability to put out as close to one amp (1000mA) as possible. I chose an old Sanyo SCP-07ADT that is rated at DC 5.4V at 800mA. The plug can be any type, no need to be USB.
2. Cut the connector off the end of the cable and strip the outer black part up about an inch and then strip the positive and negative (red / black respectively) wires up about a millimeter, just enough to have bare metal ends to touch to a small area.
3. Take your battery out of the phone, look at the back of battery for the + and - marks which correlate to one of the metal connection points on your battery, this is where you will "touch" or "attach" the bare ends of the wires.
4. Plug the charger in making sure not to short your bare leads. Before you do this double check that the OUTPUT of your charger is indeed DC voltage so that you don't hurt yourself. You do not want AC output and it can be dangerous.
Then touch the bare end of the red wire to positive of battery, and black wire to negative terminal of your battery. I held them with my fingers while surfing the web for about five or ten minutes. I had no idea if anything was happening or not but it "felt" like the battery might have gotten just a bit warmer.
5. Unplug the home-made bare wire charger and put battery in your phone. Quickly attach a USB charger or just plug into a USB cable of your computer. I pushed it in and nothing happened at first but finally I heard the standard "bleep" when you plug a USB device in. I knew that I made progress because it never beeped before it took about 30 seconds and several "bleeps" of connecting/disconnecting from USB but eventually the charge light stayed on!
It's been about 30 minutes and I'm up to about 50% charge and been using the phone heavily while charging.
So, in summary... never let your battery discharge below 5% or you can only charge it with an OEM cable rated at 1amp (rare). IF you let it discharge to "dead" then charge for 5-10 minutes with the "wire" method and then charge normally!
Thanks to Dozzen for the original idea!!
Wizard that won't charge
When my Wizard/HTC 8125 goes dead my cure for the battery is to use a 9 volt charger with the wires stripped back also. But, my method is a bit different. I place a standard Christmas Tree light bulb (the newer small ones)in series with the charger wires. Observe the correct polarity. The battery is labeled + and - so that part is easy. By using the small light bulb you are doing 2 things. 1.You can see the slight glow from the bulb and know that proper connection is made. 2. You are limiting the charging current to the battery.
If you get really creative like I did you can solder a couple of small nails or in my case a set of red and black probes to the setup and the points on these nails/probes make for much easier connections. Note.... This method may take a few minutes longer but, is much easier on the battery.
In my experience once the battery is below a certain level NO charger that I plug in will work. I just purchased a used 8125 from eBay and brought it back to life most successfully with this method.
hy there my htc wizard battery whos dead so i charched with a cable with + and - the phone starts but when i try to connect to a usb or a adaptor it doesnt charge anymore it show me the charge icon on the baterry but it doesnt charge the usb works fine it's sync to my pc but it doesnt charge anymore... what sould i do?
So it seems no one touched on what really matters here.
A design flaw, in my opinion. The HTC Wizard cannot recharge via USB unless there is enough power to turn on. The reason is because it requires the OS to charge.
So, what many people already posted are very creative ways to charge your 8125. The easiest and cheapest way, in my opinion, is to use AA batteries.
1) Take two AA batteries and tape together so they are in series. Imagine it like this... [- AA battery #1 +][- AA battery #2 +]
2) Use two wires and tape one to each side of the AA's (one on the + side and another on the other battery's - side since the - of the first battery is connected to the + of the second).
--w-i-r-e--[- AA battery #1 +][- AA battery #2 +]--w-i-r-e--
3) Connect the positive (+) wire to the positive (+) side of the phone. By this I mean the 6 metal pieces that stick out to contact the phone battery. I did it by wrapping the wire around the top most one (or second top most, it's been over a year since I've done this.).
4) Connect the negative (-) wire to the negative (-) side of the phone. Again, bottom most or second bottom most (see #3).
5) Insert phone battery while the wires are still in and connected to the two AAs.
6) Let the power flow for 30 seconds or so and then try turning your phone on. This part is the important part because you cannot use a USB to mini-USB connected to your computer to charge the phone unless the operating system can function. Meaning, it needs to be turned on first.
7) Once the phone is on, plug in the mini-USB part and connect it to a computer. I'd recommend getting at least 5% battery before disconnecting the AAs, seeing as you need to be able to start up your phone long enough for the OS to boot. Once the OS boots, you can fully charge it through a normal USB to mini-USB connection on any computer.
old post but just wanted to say thanks. Used the wire to battery method and got phone turned on after 2 mins of holding wires to battery.
As many other of you, I have had problems with my battery charging properly. Often it would only charge up to 40-60%. Usually, I could fix this problem by running my battery down to 2%, then turning it off and plugging in the charger. Most of the time it would charge up to 100% then, save for a few times it didn't.
Still, I was getting annoyed by this, so I figured I might as well try pulling the battery out and plugging it back in. And, wow, did it fix some issues for me. So far, my battery is charging itself back to 100% without having the pull the plug multiple times. But maybe even better, it gave me a completely renewed battery life.
Before reseating the battery, I was getting about 5-7.5 hours battery life depending on what I was doing. After reseating, I now have about 10.5 hours of battery life. That's a HUGE difference. The attached images below show my latest 10.5 hour battery life with about 9% left, which should give me another 45 minutes to an hour if I needed it. Power saving was on during the entire time, screen brightness varied between 10-25%. Mostly I internetted, reddited, used Feedly, 1.5 hour of youtube viewing. I put the tablet in airplane mode for one night to see if it gave any significant battery life, but it only took about 1% during the night it wasn't in airplane mode. Sync with all my accounts was also on the entire time. Android version is stock, rooted, though I only use Xposed and Greenify.
If it stays like this, this will be the first time I am truely happy with my battery life.
To reseat the battery, I used this Youtube video:
www.youtube.com/watch?v=lEVFYQksmxM
If you want to try it, which I certainly recommend, you can try pulling out only the battery cable. I wasn't able to, I didn't want to put too much stress on the cabling, so I unscrewed the entire battery. It's not stuck with adhesive anyway. I do however recommend strongly that you use this guide to pull of the back cover, instead of opening at the screen:
www.youtube.com/watch?v=f5vTAeWyq7I
Can't link to the video's themselves, I am not allowed to do that yet. I believe this video was made by someone on XDA? Please give a shout out, so I can give you proper credits for it. Becareful when opening the device when near the USB port and the audio jack. The plastic connecting to the tablet itself seems very fragile in those places.
Thanks for sharing.
Same experience, I did it two days ago after noticing that it stopped charging at 96%. With the same usage I should have needed to recharge it by now but I still have 52% battery left with my usual 3 hours of screen on over 48 hours. So it doubled the battery life .
I did remove only the connector, I used a plastic coated paper clip that I passed under the cables to pop it off. The cables are strongly attached enough to remove the connector without any issue.
I think I'll keep this tablet longer than I thought, the processor and screen being future-proof.
I'll try it and post my results...
Anybody else tried that or has a clue why that happened?
reseating battery helped, now won't charge from USB
I too have been frustrated with charging and battery issues on my Tab Pro 8.4. So I tried the battery reseating trick.
I can now report, that it has helped with battery life. But a new issue came up.
Previously, I could not reliable charge the tablet on AC power ( USB cable connected to the AC charger ). It would not charge to 100%. The solution was to charge from an USB port on my Mac. This would charge to 100%.
After the battery reseat trick, the tablet does not charge over USB, but charges nicely to 100% on AC. And the battery life is much better.
Right now, I am trying if the battery is even charging over USB while off. The little dots are scrolling on the screen, seems something thinks the charging is ongoing, but I need more time to see if the charge level has moved up.
Any ideas ? Thanks, Paul.
I had also proceed to that "surgery". Battery life seems better but it could be placebo. Im not sure.
But 3 times in a row charging went from 15, 20, 35 % straight to 100.
To the usb charging issue mentioned, due to the bad contactivity of the battery cable before tha fix, it may displayed false reading of charging level. The normal changing time from a standard usb port is at least 4 to 5 times longer than the original charger (2000mA vs 500mA max). So you have to wait longer for a usb charging level change.
About the USB charging issue - the device does charge when off, while plugged into an USB port on a Mac. When the device is ON, the battery icon shows a red cross, and the info in the Battery windows of settings is showing Not Charging. My guess is that this is some restriction on the firmware, that does not attempt to charge the device while having a data link on the USB. I will try to obtain a charging-only cable, to see if that fixes the issue.
Paul.
Just checked for myself, but my cable that came with the tablet doesn't work either. Tried it with different cables too and the same red icon pops up in the battery. I honestly never tried charging it myself via my PC before I reseated the battery. Maybe it has something to do with the fact a PC USB 2.0 port can only supply 500mAh, which isn't enough for the tablet (while it is turned on)?
I m also suffering from this charging problem...i wish to reseat bt i have a question...after opening the back cover does it reinsert normally or i need glue..?
I tried first to remove the back cover. Some of the clips chipped off. So I removed the screen. No damage removing the screen. Just be patient to unclip all spots all around the screen
kensheen said:
I m also suffering from this charging problem...i wish to reseat bt i have a question...after opening the back cover does it reinsert normally or i need glue..?
Click to expand...
Click to collapse
There is some adhesive between the cover and the tablet itself, but mostly there are a lot of small plastic pins that lock in place. I did not add any new adhesive, and I honestly can't tell the difference.
paokaras45 said:
I tried first to remove the back cover. Some of the clips chipped off. So I removed the screen. No damage removing the screen. Just be patient to unclip all spots all around the screen
Click to expand...
Click to collapse
Oh that doesn't sound good. Is the back cover still fine now with the chipped pins? I personally didn't try via the screen since I saw an image in a different thread of someone getting bubbles of some kind in one of his screen corners.
The fit close to the ir port is not as tight as before. I don't mind because i use a case. The screen came off without any issues.
PS: after power on the tablet for the first time, i forgot to set time and date. It didnt connect to any secure site or servive (play store, youtube, facebook). So keep in mind to set them correctly
paokaras45 said:
The fit close to the ir port is not as tight as before. I don't mind because i use a case. The screen came off without any issues.
PS: after power on the tablet for the first time, i forgot to set time and date. It didnt connect to any secure site or servive (play store, youtube, facebook). So keep in mind to set them correctly
Click to expand...
Click to collapse
So, after some days, how do you note the battery? Improved indeed?
favero_ said:
So, after some days, how do you note the battery? Improved indeed?
Click to expand...
Click to collapse
I think yes. I now get full charge every time (5 times from various percentages) and screen on time increased by an hour approximately. Maybe its from the better changing cycles.
With medium usage (tapatalk 20%, greader 30%, facebook 20%, youtube 30%) no gaming at all i get about 6 or more s.o.t. at 20% brightness most of the time.
Right now i am at 30% left with 5 hours sot, unpluged 13 hours ago.
I reseated my battery..now my tab pro showed it is full charged after long time. Previously it didnt cross 29% even i charge it for whole day..battery is better now. I opened the back cover by ruler and reseated only the battery connection as shown by video...
thankx sicron.
are you guys sure there is nothing wrong with your charger, you should get a usb amp reader (like $5 on ebay) and make sure the tablet is pulling 1800~ mA when it charges from 50% or less (rate will drop when it gets close to full)
Also always use the Samsung cable that came with the tablet since it has high quality Copper wires that can carry the correct 2A current , if you use another cable it is most-likely only rated for 500 mA (Computer USB current) and will either
1. Not carry enough current to properly charge the tablet.
2. start charging ok but as the cable heats up (or contact pins on the usb parts) it will start to degrade
I suggest only using the Samsung wall charger, and never Ipad , iphone, computer or other brand chargers to charge it.
otyg said:
are you guys sure there is nothing wrong with your charger, you should get a usb amp reader (like $5 on ebay) and make sure the tablet is pulling 1800~ mA when it charges from 50% or less (rate will drop when it gets close to full)
Also always use the Samsung cable that came with the tablet since it has high quality Copper wires that can carry the correct 2A current , if you use another cable it is most-likely only rated for 500 mA (Computer USB current) and will either
1. Not carry enough current to properly charge the tablet.
2. start charging ok but as the cable heats up (or contact pins on the usb parts) it will start to degrade
I suggest only using the Samsung wall charger, and never Ipad , iphone, computer or other brand chargers to charge it.
Click to expand...
Click to collapse
It is definitely not the charger, otherwise the problem wouldn't be fixed by reseating the battery. Which happens to work for a lot of people. I personally tried a Nexus 7 2012 2A charger both with the original cable and with my Samsung cable. I also tried the OnePlus One charger (2A or 2.1A, not sure) with both cables and it didn't charge. It seems to me it is some kind of calibration issue, that somehow gets fixed by unplugging the battery and plugging it in again.
Sicron said:
It is definitely not the charger, otherwise the problem wouldn't be fixed by reseating the battery. Which happens to work for a lot of people. I personally tried a Nexus 7 2012 2A charger both with the original cable and with my Samsung cable. I also tried the OnePlus One charger (2A or 2.1A, not sure) with both cables and it didn't charge. It seems to me it is some kind of calibration issue, that somehow gets fixed by unplugging the battery and plugging it in again.
Click to expand...
Click to collapse
Yeah strange, maybe some-kind of a bad connection on the battery clip where on the assembly line it didn't get fully pressed down or just comes loose overtime, and maybe the battery wasn't reporting back stats correctly (if you look in logcat you can see it constantly is getting updates from the battery circuitry)
would be interesting to see what logcat reports on a device with this problem (might need root logcat)
IE mine shows this.
D/BatteryService( 944): level:61, scale:100, status:3, health:2, present:true, voltage: 3836, temperature: 248, technology: Li-ion, AC powered:false, USB powered:false, Wireless powered:false, icon:17303447, invalid charger:0, online:1, current avg:-784, charge type:0, power sharing:false
Click to expand...
Click to collapse
X
xx
I completed the battery reseating and can say it definitely has improved the battery charging and performance. Prior to I was having the charging stopping issue at various percentages. Since the reseating it now charges 100% and the battery performance has definitely increased by at least 20%. Would recommend to do this if your having battery issues. Take off the back cover as it is very easy. Just need to go slow around the perimeter. It is help on by small clips and glue. Use a slow and forceful prying with a credit card and the back cover will slowly become undone. Area around the charging port has a little extra glue so may take a little more force.
Hi everyone;
I've having an interesting time with my nexus 7 (2012 wifi 32gb).
Before I left on vacation I couldn't get the thing to charge. Looking at the usb port I thought it had become to damaged to make a good connection. So while I was away I ordered a new port assembly. Installed that and still no charging.
Oh the battery cell voltage had gone down to 2.2V so it's in a sleep mode. No problem used a proper lion charger to trickle charge it back to life then further to about 3.8V.
At that point it boots up though the optimization took the charge down to 2% so couldn't do more testing but clearly it worked just fine. However the thing won't charge. Plugging it in to USB it does detect the connection but does not draw any current (as shown by a usb voltage/current monitor). It will show the charge screen, go through 3 cycles of the battery filling animation then shut off.
I check and the voltage is getting from the usb cable into the connector. I traced the ribbon cable from the IO board up to the motherboard and at the other end I also get a nice 5V reading. Clearly the connection from the USB to the device is being made no problem.
At this point I am thinking that maybe I blew the charging circuit. When I was orignally trying to get it to charge before leaving I was applying all kinds of stress to the connector to get it to charge and there was a few times where I think I shorted it (usb monitor showed >3A and the device reset).
Anybody have another theory?
At this point I can't really use it as charging the cell externally is dangerous and not convenient. At this point from what I have seen with my testing and on here if I want to use it I would have to apply 5V to the battery connector (sans battery) which I haven't tried yet.