Related
I got a serious problem with my mda vario here.
sometimes, 7 out of 10 times, when i get a call the screen gets totally corrupted and jumbled like on the picture in the attachment. i can only see black vertical lines on a white screen. in order to make the screen work properly i have to turn the phone off/on (stand-by mode) then.
does anybody know where the problem is?
i have to confess, that the phone slipped out of my hands and fell on the ground 3 times so far.
thanks
well, you say youve dropped it 3 times already? is it possible that something may be loose inside? is there cosmetic damages from dropping?
yes, there are some scratches on it. i don't really think that something is loose or broken, because the screen gets only on icoming calls corrupted.
so i don't think that it is due to a loose contact or something like that...
I have exactly the same problem. I personally think it is unlikely that dropping the phone has caused it as it corrects when you cycle the power button. Any help on this from other forum member would be much appreciated.
roads said:
I have exactly the same problem. I personally think it is unlikely that dropping the phone has caused it as it corrects when you cycle the power button. Any help on this from other forum member would be much appreciated.
Click to expand...
Click to collapse
Any resoluation this? I have the exact same problem!!
Oh dear ... somethings in the air...
mine's got it also. first time i saw it was a couple of days ago. only happens with the alarm clock in the morning :?
My phone is crap like hell... gotta hard reset and reconfig the damn thing. acting up lately...
(ps... AFAIK i barely dropped the phone... maybe 1 or 2 times. nothing more)
I have the same problem
I have read the service manual of wizard and said:
Unusual Vertical / Horizontal lines or partial display
(1) Check the connection of LCM FPC whether is properly connected. (Is a conector between motherboard and LCD)
(2) Try with another LCM. (LCM=LCD Screen)
(3) Try with another Main Board.
(4) Replace LCM if necessary
(5) Replace Main Board if necessary.
(6) Once the defective part has been identified, verify it again with the defective part whether the
symptom could be duplicated
Any sugestion?
Okay..
so far, i have installed Molski 2.26 rom (30meg free version) and upgrade the radio rom form 2.25 to 2.47.
I have not had another occurance of this so far.
Maybe a fluke.
Screen fixes when pressure applied to bottom of the screen
Guys,
I now have to keep my finger pressed hard against the bottom of the lcd unit to get the screen to display to work properly. it is under warranty with Imate but they want me to send it to Abu Dhabi for repair. I'm in Canada and concerned that I may not get it back.
So has anybody else identified this as being a loose connection rather that a real hard fault. Also has anybody fixed their unit by dismantling and reseating the connections.
Finally has anybody used the Imate repair service and was it timely & reliable?
Any advice would be appreciated.
Mick
This is a real hard fault.. had it with my mini s, took it into the shop, it was away 2 weeks... and in the end they gave me a replacement!!
I agree - took it completely apart and cleaned everything ....
And still have the issue.
Serves me right for buying something in Middlesbrough I suppose
It must be a hard fault with the LCD assembly. Will have to see how Dixons handles an overseas repair.
Take care & thx,
Mick
I had the same problem, in the end i took it into my local t-mob shop to have it repaired, they ended up sending me a new one.
Well, I've exactly the same problem since the past two-three weeks, it also occurs only in the morning. I'm living in the Netherlands and this is happening since it's rather cold over here, especially in the morning (3-4 degree Celcius). Since my bedroom window is open during the night, it gets rather cold in my room.
During the rest of the day it is +8 degree Celcius, and the phone works flawless. Maybe this problem has something to do with the Temperature?
Temperature
Bebob - don't thin so as I have had this problem for a number of months and the temp here in the summer is high (30+ degrees C)
It looks to be a bad connection type issue and may be a bad screen cable. It makes sense though that the issue is at the bottom of the screen cos this is where we press the select buttons all of the time.
Pls keep me posted on how you do. mine is going to a local repair shop (on my dime) tomorrow to see if they can fix it.
If not can any of you guys recomend a new unit that could be considered an upgrade to the KJAM ?
Many thanks
Mick
suggestions needed
friends, i have o2 mini s and got the same problem with screen for the last 3 weeks....
can anyone tell me that will the problem aggravate or else will i be able to use my cell properly for few months...
and also what will be the approx cost of repair..
all suggestions will be warmly appreciated...
It's happened to me as well. I have lived with that for one month now. It is happening, when I touch the cursor keys or when touch the lower part of the display. I tried "shaking/hitting" the xda and it looks better, so I assume it is a faulty connection cable.
I have active Cleartype and no more vertical lines for the past 2 days.
I seems to be a problem when background is white and leters are black.
Regards
similar problem
i dropped the phone (T-Mobile MDA Vario) and now when i turn it on the screen is fine for 5-30 seconds but then it scrambles, but works again if i smack the bottom of the phone on my hand!
t-mobile staff told me there are sensors to identify if it has been dropped. I'm suspicious that it could even be programmed to go "faulty" once it is dropped as the screen is fine for a limited time so it obviously works somewhat. do you know if this is the case? or what's happened? also is it a simple thing i could do myself? i didn't take out insurance so that's why i haven't just claimed off that as i'm really broke
Any help is appreciated
Regards,
Steve
whiteish screen / over temperature
hi,
I have a problem smilar at qtek 9100. I had upgade to my ppc wm5 to wm6 around 3 week ago and overclocked to 221 mhz with batery status today plug-in . 2 days ago Screen became whiteish (almost no contrast or over gamma) and working temperature is around 30c. I tried to re-flash with many kind roms but noting chaged.
Is there anybody has these kind of experice. If I can not solve. I am planing to buy new LCD ( I am not sure new LCD will solve the problem)
Thanks
Same problem here. Dropped it ONE time and the screen went crazy. Sent it to my t-mob shop and they got it repaired. They said in the report that they changed the "flex". Dunno if this helps.
Hello
I bought mine Vario II (with CoPilot) just 8 days ago, so I've enjoyed it quite a lot for the past days
yet .. ~30 hours ago I found out that the touch screen was not responding at all .. well restart did not help, getting the battery out and putting it back again didn't help too ... I tried to do EVERYTHING with the thing ... starting with restoring factory settings (all the data! ) , ending with browsing the forums for common failures ...
Finally I ended up with the very start page where the Vario II asks for tapping the screen (irony huh ?) to start setting it up ..
Since I was not able to make it work again (the whole thing seemed to be working fine ... just the touch screen ... ) so I brought it to the local T-Mobile shop today in the morning.. guess what, the guy at the shop just removed the battery and put it back again (I've done that XXX times during the night) AND IT STARTED WORKING again ... I couldn't understand anything there, felt really lame
anyway after I've left the shop and used it for quite a bit it started again .. now I've kind of figured it out .. when I'm using the device actively (the temp raises) and it starts at the top right corner of the screen .. the touch screen just flickers there and then after a minute or so it doesn't respond at all any more .. if I just put it away and don't use it - the screen responds again after some time ...
NOW finally the question is: has anyone had any problems with Vario II like I do? I ought to think that it is a somewhat faulty device that I've got (it hasn't been physically damaged)
PS the touch-screen gets stagnant faster with bigger programs (CoPilot, Skype, etc...) and it takes some time to get stuck with just using the phone...
btw I've put a temperature thingy in the device - it shows that the battery temp is at 42 C . Isn't that a bit too much ?
yeah and how do I figure out what version it is ? I mean the S/N that is mentioned here ( http://wiki.xda-developers.com/index.php?pagename=Hermes_Problems )
?
wundis said:
anyway after I've left the shop and used it for quite a bit it started again .. now I've kind of figured it out .. when I'm using the device actively (the temp raises) and it starts at the top right corner of the screen .. the touch screen just flickers there and then after a minute or so it doesn't respond at all any more .. if I just put it away and don't use it - the screen responds again after some time ...
NOW finally the question is: has anyone had any problems with Vario II like I do? I ought to think that it is a somewhat faulty device that I've got (it hasn't been physically damaged)
Click to expand...
Click to collapse
Yes, one of my Hermes' had the exact same problem - touch screen malfunction starting at the upper right corner when temperature rose. The usual tricks to solve the screen alignment problem (loosening the screws, removing the gasket with a stripe of a business card) didn't help at all. I returned the device and got a new one.
yeah and how do I figure out what version it is ? I mean the S/N that is mentioned here ( http://wiki.xda-developers.com/index.php?pagename=Hermes_Problems )
?
Click to expand...
Click to collapse
It's printed on the box (at least of an O2 Trion) and on the sticker underneath the battery. Just look for the S/N starting with HTC6xx... but "our" defect is not the normal SA problem, it seems to be much rarer and not described in the Wiki.
Cheers
Daniel
Thank you so much for the answer Daniel, I'll get them to change it tomorrow.
I have exactly the same problem with my TyTN. In the morning, after the phone has been off all night, the touchscreen works for maybe 30mins, then the phone warms up and the screen ceases functioning. Bizarre though - I got the phone about two weeks ago - the screen worked fine (i.e. under all temp. conditions) for about 7 days, then it decided to crap out. Tried all the usual SA type solutions - as you guys noted above they didn't work. Gonna have to go back to the shop and get it replaced :-(
Oh, nearly forgot, s/n is HT632
One other thing I noticed (not sure if this is normal behavior or if it started after the touchscreen borked) - When the phone is active (i.e. not locked or in standby,) the top status leds (wifi, bluetooth, gsm) don't flash. Once the device is put in standby (i.e. tapping the power button) they start flashing again. Like I said, not sure if this is normal or if its related to the touchscreen going.
Vrobenmat said:
One other thing I noticed (not sure if this is normal behavior or if it started after the touchscreen borked) - When the phone is active (i.e. not locked or in standby,) the top status leds (wifi, bluetooth, gsm) don't flash.
Click to expand...
Click to collapse
This is definitely not normal. But it's an interesting observation. If the TyTN were a car, I'd say there's a bad ground connection somewhere.
Try a hard reset, and if that doesn't solve the problem, have it exchanged. (I very much doubt that a hard reset will help, but at least here customer service refuses to exchange a device before you tried a hard reset. )
Cheers
Daniel
Hard reset borked even more. Could't get past the touch screen calibration. Phone is now in the freezer to cool down - hopefully the touch screen will work long enough so I can get past the calibration
*EDIT* Just got it out the freezer (nice and cold now.) Hard reset, got through the calibration, everything ok for about 10 mins. LED's flashing with backlight on and touchscreen working. Then - touchscreen non-responsive at exactly the same time the status LED's cut out. I'm hypothesising that there's some kind of electrical short between the circuitry for the touchpad and the status LED's - it shorts as the devices temperature rises and (i guess) some of the materials expand and come into contact with each other. Since I don't want to void my warranty in case I have to take the phone back to the store, I haven't opened it up to confirm this. Has anyone had a detailed look at the connections at the top of the screen and around the status LED's to see if my explanation is at least possible? (then I might open it up and see if I can insulate the connections.)
tadzio said:
Yes, one of my Hermes' had the exact same problem - touch screen malfunction starting at the upper right corner when temperature rose. The usual tricks to solve the screen alignment problem (loosening the screws, removing the gasket with a stripe of a business card) didn't help at all. I returned the device and got a new one.
It's printed on the box (at least of an O2 Trion) and on the sticker underneath the battery. Just look for the S/N starting with HTC6xx... but "our" defect is not the normal SA problem, it seems to be much rarer and not described in the Wiki.
Cheers
Daniel
Click to expand...
Click to collapse
I have the exact same problem!!
Two additional points :
1) my device screen will not switch off automaticaly and will stay on for ever unless I switch it off
2) When the issue manifests itself for the first time the device would automaticaly go back to the today screen like if the OK button would have been pressed many time or ... was stuck!!
That's my second Tytn device the first one had the SA defect.
I was so happy when I got my new one because the S/N showed HTC637XXX but sounds like a new issue even though I'm pretty convince that that the SA issue is not far from being related to this one.
My device SPV3100 HERM100
Hello lads,
Absolutely everything you've posted seems to be happening to my device.
Now the touch screen fails to respond even if it's cold (been lying on the bed for 5 hours doing nothing at all .. ). damn... seems like I'll have to ask the local shop to get me a free portable refrigerator for the thing to work properly
HT645
Vrobenmat said:
Hard reset borked even more. Could't get past the touch screen calibration. Phone is now in the freezer to cool down - hopefully the touch screen will work long enough so I can get past the calibration
*EDIT* Just got it out the freezer (nice and cold now.) Hard reset, got through the calibration, everything ok for about 10 mins. LED's flashing with backlight on and touchscreen working. Then - touchscreen non-responsive at exactly the same time the status LED's cut out. I'm hypothesising that there's some kind of electrical short between the circuitry for the touchpad and the status LED's - it shorts as the devices temperature rises and (i guess) some of the materials expand and come into contact with each other. Since I don't want to void my warranty in case I have to take the phone back to the store, I haven't opened it up to confirm this. Has anyone had a detailed look at the connections at the top of the screen and around the status LED's to see if my explanation is at least possible? (then I might open it up and see if I can insulate the connections.)
Click to expand...
Click to collapse
Might get a chance to have an internal look tomorrow. From memory, and can't remember if the Wiki or Japanese dismantling site shows this, but I recall only a single mylar ribbon cable coming from screen area through to main board. There are if memory serves push in multi connectors from the bottom hard keypad and from front camera board (inc LEDs) to the muti ribbon cable on the back of the screen. Thus, simply put the screen, camera,hard phone keys all connect at the back of the screen to a single multi ribbon cable that goes to main board. Possibility then of a short with digitizer is at least possible. Of course digitizers are suceptible to current leakage and field interference so would not have to be an actual physical contact but could just be a close proximity issue.
Mike
Facing the same problems...
... I've been thinking about repalcing the display and the touchscreen. But now, considering that it is a HW issue, I can only replace these two things. If the bug is in the module above the screen (statur leds and camera) or related to the wireing at the back of the screen, it won't get rid of the problem. On the other hand, if it is a problem with the screen getting too hot, then I'm on the right track...
Has anyone tried this yet?
I'll try to call HTC on monday, maybe they know where the bug is.
HTC is not able or not willing to share what they know about the problem...
Hello, they excuse my English, I am possessor of a TYNT and I am with he himself problem that you, the problem is a failure of weld in the processador, when it reaches certain temperature fails and cooling it or pressing strongly on the processor it lets fail.
Greetings.
ezbook said:
Hello, they excuse my English, I am possessor of a TYNT and I am with he himself problem that you, the problem is a failure of weld in the processador, when it reaches certain temperature fails and cooling it or pressing strongly on the processor it lets fail.
Greetings.
Click to expand...
Click to collapse
There may well be truth in what you say, I too believe it is something similar in some cases.
Do you have any proof of your suggestion. Can you provide pics or a diagram of the solder point you mean??
Mike
Hmm? The processor...?
...sorry, don't think so.
It's just that this bug occurs after using a device for months, isn't it?
Now, the first two weeks I installed all kind of programs using the wireless LAN almost permanently. My Hermes was never as "hot" as during its first two weeks. And what about the sliding-out of the keyboard? Doesn’t it always start there? This just doesn't sound right, does it?
Just received an email from someone who drew my attention to the ribbon cable connecting the upper and the lower part. What if there is a short one due to the plastic scratching the cable and then... who knows?
However, I do not disagree as far as the temp is concerned. Therefore, I'll put my Hermes on ice and see how long it does things right...
And still, there is no chance that it is related to the processor. If the processors ALU is getting too hot the entire device would be effected, wouldn’t it?
Anyways, I'm determined to find out what it is!
++ I just found a very peculiar post in the WIZARD forum. It was about some top-side buttons that kept pressing
++ without even touching… Opening the assigned programs over and over again. Odd, isn’t it?
++ That’s a HTC device AND has a sliding keyboard with a ribbon cable as a connector…
++ Yet, it operates with a different processor on a different main board.
++
++ Still blaming the processor?
microft said:
...sorry, don't think so.
It's just that this bug occurs after using a device for months, isn't it?
Now, the first two weeks I installed all kind of programs using the wireless LAN almost permanently. My Hermes was never as "hot" as during its first two weeks. And what about the sliding-out of the keyboard? Doesn’t it always start there? This just doesn't sound right, does it?
Just received an email from someone who drew my attention to the ribbon cable connecting the upper and the lower part. What if there is a short one due to the plastic scratching the cable and then... who knows?
However, I do not disagree as far as the temp is concerned. Therefore, I'll put my Hermes on ice and see how long it does things right...
And still, there is no chance that it is related to the processor. If the processors ALU is getting too hot the entire device would be effected, wouldn’t it?
Anyways, I'm determined to find out what it is!
++ I just found a very peculiar post in the WIZARD forum. It was about some top-side buttons that kept pressing
++ without even touching… Opening the assigned programs over and over again. Odd, isn’t it?
++ That’s a HTC device AND has a sliding keyboard with a ribbon cable as a connector…
++ Yet, it operates with a different processor on a different main board.
++
++ Still blaming the processor?
Click to expand...
Click to collapse
And you are right too! if it appears that I am tending to agree with both above posts when on the face of it they disagree with each other it's because:
1
There are different manifestations of this problem - the causes may not always be the same
2
I agree it's NOT the processor and firmly believe it's hardware related. Of course it could be be a break (sometimes intermittent) in contact somewhere between screen and board or even a broken contact on the board (IN SOME CASES)
3
In other cases it's just pressure being put on the touch sensitive screen often at the very inconvenient top right corner that closes/minimises applications or opens start menu.
There has not been a reliable way to fix this issue other than device replacement. Replacing the screen has been notable for it's failure to resolve the issue.
Mike
mikechannon said:
And you are right too! if it appears that I am tending to agree with both above posts when on the face of it they disagree with each other it's because:
1
There are different manifestations of this problem - the causes may not always be the same
2
I agree it's NOT the processor and firmly believe it's hardware related. Of course it could be be a break (sometimes intermittent) in contact somewhere between screen and board or even a broken contact on the board (IN SOME CASES)
3
In other cases it's just pressure being put on the touch sensitive screen often at the very inconvenient top right corner that closes/minimises applications or opens start menu.
There has not been a reliable way to fix this issue other than device replacement. Replacing the screen has been notable for it's failure to resolve the issue.
Mike
Click to expand...
Click to collapse
So do you think the bug is to be found on the main board at all?
I'm planning to replace some parts from the screen half. In fact there are just 3 possible error sources:
1) The lcd in combination with the digitalizer;
2) The ribbon cable connecting screen parts and keypad at bottom; and
3) The keypad at the bottom itself
The ribbon cable includs the electronics for the status leds as well as the EARphone. ;-)
Soon I will be on all three of the above parts and if the error ain't there... I'm going to be MAD.
Will keep you IN THE LOOP!
Hello again, my conclusion is based on which I have disassembled my TYNT completely and I have connected it without the keyboard, of this form I have hoped to that it began to fail, later I have been moving and touching in any case the flat cable that unites the motherboard with the screen, the small circuit that takes built-in without obtaining results, single I have even obtained that it returns to work blowing air on the strongly pressed processor or on. Another observation is that if just ignited the machine and working correctly we applied single heat on the processor, begins to fail the touch screen. To my also is to me strange east failure since the temperature of the processor is not excessive when it fails, in fact desire firmly to be mistaken because there am lost the guarantee. Seguire investigating is matendre informed to you.
Greetings.
microft said:
So do you think the bug is to be found on the main board at all?
I'm planning to replace some parts from the screen half. In fact there are just 3 possible error sources:
1) The lcd in combination with the digitalizer;
Click to expand...
Click to collapse
May be a fault there, but if it's just a squeeze due to heat ? pressure it may not resolve the issue.
2) The ribbon cable connecting screen parts and keypad at bottom; and
3) The keypad at the bottom itself
The ribbon cable includs the electronics for the status leds as well as the microphone.
Soon I will be on all three of the above parts and if the error ain't there... I'm going to be MAD.
Will keep you IN THE LOOP!
Click to expand...
Click to collapse
I assume you mean earphone above as the microphone is on the mainboard.
Mike
Again I have tested, with the disassembled machine totally, start up it, I hope to that the touch screen does not respond and I put my tynt in the refrigerator, after two minutes and without moving I touch it the screen and magic, works correctly hata that again coje the room temperature.
Greetings.
ezbook said:
Hello again, my conclusion is based on which I have disassembled my TYNT completely and I have connected it without the keyboard, of this form I have hoped to that it began to fail, later I have been moving and touching in any case the flat cable that unites the motherboard with the screen, the small circuit that takes built-in without obtaining results, single I have even obtained that it returns to work blowing air on the strongly pressed processor or on. Another observation is that if just ignited the machine and working correctly we applied single heat on the processor, begins to fail the touch screen. To my also is to me strange east failure since the temperature of the processor is not excessive when it fails, in fact desire firmly to be mistaken because there am lost the guarantee. Seguire investigating is matendre informed to you.
Greetings.
Click to expand...
Click to collapse
This is very interesting. When I said above it is not the processor, I meant it is not a software issue related to the processor. It can of course be a heat related problem with the processor. To summarise what you have found:
1
You have a device that when first started works OK
2
If you apply heat (but not much) to the processor it fails
3
If you apply pressure to the processor it works again
4
It begins working again when you blow on the processor or put it in the fridge.
5
If you move/press or ensure the ribbon cable has a firm contact - this has no effect.
Please post if any of the above is NOT correct ALSO please post which chip you are heating/pressing.
Cheers
Mike
Hello again, everything is correct except point 3 really when this failing and you press on the then microprocessor the touch screen works correctly. Associate images.
Greetings.
EDIT by Mike. Point 3 has been edited in Mike's post to show the correct situation.
Hi all,
I need help,suggestions,anything with an issue I've had for a while. Since the time I started loading WM6 the screen has been randomly fading to white. I have LSVW latest rom 22/4 SE and 1.40.10 radio and 1.40oli although it doesn't matter what rom you load. I tried going back to WM5 and its better but now still fades to white as well.
on advise from oli and legolas I purchased a new battery but still have the same issue.
I have dropped my phone once which resulted in a crack to the right of the DEL/CR keys so could it be a HW issue and if you think so is it one I could open up the phone and fix?
Any and all help appreciated
IN FACT IF SOMEONE CAN RESOLVE THE ISSUE I WILL DONATE SOME CASH TO THEM!
test
Im updating to
LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
seeing if any difference comes out.
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
mikechannon said:
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
Click to expand...
Click to collapse
HHmmm interesting thread .. the only issue i have out of that is the fade to white one.
Maybe Hardware .. i got the phone off ebay and now it has a crack in it .. so i dare say it isnt under warranty any more. (even though its a max of 6 months old).
It may also be software. I experienced the WSOD on my JASJAM when playing with the GPS-related DLL's. Once this problem appeared when switching on the camera. The screen would turn white and soft reset would not fix this, only power off/on would sort it out. Seems that the drivers do not reset (some of) the hardware to a known state on boot.
Had EXACTLY the same problem. Hoped it would be a software problem. Hard-reset a few times to no avail. Upgraded to a couple of the WM6 ROMs. No change. I did notice that when it was cool it tended not to happen, but after being on the phone a couple minutes or using the PDA for a while, it would do it AGAIN.
One weird thing I noticed was that if I did a Soft-reset and held down the Left Soft-key, I could "force" it to fade to white on start-up! VERY WEIRD.
I finally bit the bullet, and sent it back to Telstra to get it sorted. Didn't want to void warranty myself.
It has been just over 2 weeks since I sent it off, and They have sent this reply...
-------
-------
Hi
This phone is currently waiting on a part which was ordered yesterday. Some parts have already been issued but needs further repair.
Regards
Nadine
--------------------------------------------------------------------------------
From: LJ Boyd [mailto:[email protected]]
Sent: Friday, 20 April 2007 2:18 PM
To: ! TMS Customer Service
Subject: RE: Imate JASJAM Problem
Hello, I am emailing about an I-Mate JASJAM phone I sent for repairs early last week (tel # xxx ).
Can you please update me as to status of this repair, as the Telstra shop did not provide me with a second phone while I await return/repair/replacement of the phone.
Thanks,
-------
-------
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
jyetara said:
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
Click to expand...
Click to collapse
Their reply was not very technical - does not surprise me however. The people who repair these devices are usually faced with some component/connection/screen or a m/board that needs replaced. They often fail to take account of something as basic as the case pressing on the screen or other components - particularly when device is warm. So they replace the component they think is faulty and then discover the problem is still there. With this issue in particular I think that there are no faulty components just the case is a fraction of a millimetre too tight for the internal components and hence swapping out parts can have no effect. With this fault I advise people to go for a replacement not a repair if possible.
NB: This issue should not be confused with white screen that may appear after installing particular software or when an application crashes, or when the flashing of a new ROM goes wrong! The hardware issue arises most commonly when the device gets warm or put another way goes white after maybe 10 minutes of use and will continue to go white even after hard reset.
Mike
I have this same problem! =(
My phone screen recently (4-5 days ago) started to go white. I never saw this happen with my own eyes but when i picked up my phone and its sleeping i push the power button to get to an all white screen. I can hear noises when i touch the screen but no image other than white. I can solve this by removing the battery and putting it back in, then my scren works fine....its not verry often just like 1-3 times a day.
I want to try a hard reset but have a question first: My phone is unlocked by the ebay guy i got it from, will a hard reset lock my phone back to Cingular?
Next i want to try upgrading my ROM and Radio and anything else...im looking in the wiki for instructions on how to do this. Any help? What else shouls i upgrade?
Ive only had my Hermes for around 2 months so im new to much of this.
THanks!
I recently purchased a Used Imate Jasjam (Ex Telstra Australia) with this issue.
I pulled the unit apart, and reseated and pressed the Power and LCD Display Data Cables... attempting to ensure they were firmly fastened.
I then upgraded to LVSW's Latest WM6 Release.
I have had the Phone go to White once in that timeframe since. I brought it back by pressing the power button of, then one again.
I don't feel that it's really a "100%" Faulty Part... Because it works fine othertimes. It almost seems as if connections or a Data Cable has an Issue.
I'm intending tonight and using the Phone over the weekend to see if the issue continues to occur.
BAD NEWS!!
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
My girlfriends phone was having the same problem. Try popping out your SD card and putting the phone into/out of sleep and see if that brings back a visible screen. Thats how we determined her situation was a hardware problem and not a problem with the rom.
jyetara said:
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
Click to expand...
Click to collapse
Yes, sadly this is kind of predictable as I said in an earlier post in this thread:
http://forum.xda-developers.com/showpost.php?p=1233420&postcount=7
This is why, as I said, get a replacement not a repair if possible. My view is that the individual components are fine but connectors come loose or the heat generated causes pressure to be put on the screen etc So it's a problem with some cases and how the innards in some cases get squeezed. So off course changing the top poly board, connectors, bezel gasket, may by pot luck make a difference but is just as likely to make no difference at all.
Mike
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
VolarisPtyLtd said:
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
Click to expand...
Click to collapse
We wait to see. Mind you one guy on these boards found he could get half an hour from his device if he put it in the freezer for a while - so I'm not sure that air-con will be strong enough!!!
Mike
Well Results.....
After pulling apart the unit and reconnected, I think I found my cause to simply be excess pressure.
I've removed the "Black Plastic" Micro SD Card from its Blanking Plate.
Since I've done this... not one White Screen Whatsoever.
I don't use an SD Card, so the issue is resolved for me, however it is very interesting.
Could be Pressure or Heat (Small Hole Might Increase Airflow/Allow for Greater Dissapation or something)
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
FaCeOff said:
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
Click to expand...
Click to collapse
You are right to ask the question "is it hardware or software".
1
We know a white screens can arise if folk duff up flashing a new ROM.
2
We know there is a hardware caused white screen that comes and goes often when device gets warm.
3
But there maybe white screens caused by some kinds of crashing software or a buggy ROM etc
Crucially in terms of finding a cure will be distiguishing between these.
2 for most people is easy - take it back and get a replacement.
1 is a matter for the ROM upgrading and fixing boards
3 is a case of trying different ROMs testing 3 party software by selective installation until the problem starts or stops.
In your case I am worried that this is a number 2 device as it did sometimes get the problem before you flashed the ROM and now it's worse. It may only be worse because this particular ROM is generating more heat and consequently more white screens. (see explanations elsewhere).
I suppose if it's an occasional problem you might live with it but otherwise it's replacement at best and repair as a rather dodgy alternative.
Mike
Hey Mike,
well, before flashing the device with a custom ROM, in my opinion it was really difficult to use it.
By flashing it with V 2.5, it was very good usable and with V 3.0 it returned to become more unusable. Nevertheless, i upgraded 10min ago with HARD-SPL-V7 and it's running fine now (i've been wating with downgrading to V 2.5. If it returns to become unstable, i will downgrade to V 2.5 again.
I'll keep you informed.
yes for this particular "white screen" issue it will be useful to hear how things go - thanks
Mike
White screen - in my case definitely a hardware issue
Hi folks,
i was testing and playing around with my Hermes and today i found the problem (very funny because now i can't reproduce it anymore but just read ahead).
Today i was playing around and after pressing by accident on the case of the Hermes, the screen appeared disappeared and changed into white.
Please download the video i recorded from the attached link - you'll see that it was able to reproduce it by tapping on the case:
http://asuka.descipe.de/dphome/test/HTC_Hermes_White_Screen_issue.mp4
Please use VLC or MPC (additional codecs required) to watch the movie.
Honestly i'm not sure if this can be reproduced by anyone but this makes the whole situation much more clear.
Any feedback is welcome.
Cheers
Dear friends
After opening my Hermes a few times I encountered the white screen, I disassembled and assembled again, the display was completely off. I thought the flex cable could be wrong. So, at first I tried to use a soldering gun to seal all solderings (Photo 1). This time the phone showed a part of display. Because, the symptom was not the same, I guest contact between the flex cable and the mainboard had problem. I used point of a knife (make it blunt first) move down to push contacts out (Photo 2). Then I assembled my phone, everything returned normal. (9h in the morning to 11h in evening to make my heart cheerful again ).
I write my experience here for someone who open their phone and encounter the symptom like me.
Good luck.
Sadly didn't work for me. Stil no backlight!
unicorn78 said:
Dear friends
After opening my Hermes a few times I encountered the white screen, I disassembled and assembled again, the display was completely off. I thought the flex cable could be wrong. So, at first I tried to use a soldering gun to seal all solderings (Photo 1). This time the phone showed a part of display. Because, the symptom was not the same, I guest contact between the flex cable and the mainboard had problem. I used point of a knife (make it blunt first) move down to push contacts out (Photo 2). Then I assembled my phone, everything returned normal. (9h in the morning to 11h in evening to make my heart cheerful again ).
I write my experience here for someone who open their phone and encounter the symptom like me.
Good luck.
Click to expand...
Click to collapse
I had a problem with no backlight but fixed it when I replaced the flywheel. I was trying to update a replacement jasjam I'd bought off of ebay but when I replaced the new flywheel with the old the backlight wasn't displayed so I tried the old motherboard with the new flywheel and the backlight was on. I don't know how it affects the backlight but it did. If you can get your hands on a cheap bung phone or have a REALLY trusting friend then try that.
Cheers...
ultramag69 said:
I had a problem with no backlight but fixed it when I replaced the flywheel. I was trying to update a replacement jasjam I'd bought off of ebay but when I replaced the new flywheel with the old the backlight wasn't displayed so I tried the old motherboard with the new flywheel and the backlight was on. I don't know how it affects the backlight but it did. If you can get your hands on a cheap bung phone or have a REALLY trusting friend then try that.
Cheers...
Click to expand...
Click to collapse
Sorry mate, what do you mean with the flywheel? English is not my mother language and what I have found in the net for that word does not mean anything to me. Can you provide me with a better explanation? I do have the same problem as the guy which writes above you.
Cheers
The little wheel on the side of the Hermes. I replaced the board That has it on it and it fixed the backlight issue.
Do I blame the onboard video or the LCD itself for this problem? I've taken the phone apart and re-seated the motherboard connections, which was no help. If I connect using EveryWAN the phone appears to be working fine, in fact I flashed the T-Mobile ROM and than the Button ROM thinking it was a IPL/SPL issue. Even if I try to start in boot loader mode the screen still looks the same.
Just trying to decide If I need to replace the motherboard or the LCD.
Thanks,
Bump back to the top!
Screen seems intact without any damage visible, no cracks or out?
Had this problem once with my old Universal, was the colour transfer wires that were loose, but pretty sure the Uni is totally different to our wizards.
Prehaps open her up and see if theres anything thats loose prehaps.
I had it opened and re-seated both the connecting cables, but no luck.
Ive had this problem with my wizard .. i couldnt find a solution. tho i didnt really try very hard. Basicaly just picked up another one on ebay for like £30 seemed cheaper than spending the time and effort fixing it. I think mine got progressivly worse. It used to do it occasionaly and now just it as soon as its switched on
i have a same sort of problem...
left of the screen fills with lines and the whole screen fades to white.
turning on and of the screen via power button takes it back to normal but then it happens again.
noticed it only happen in portrait so i have to set it to landscape all the time
for some rom and spl's it happens just a few times a day and others i cant use it in portrait.
If i find a solution it might be working for you to
Fading white screen of death
Could be the battery. Have you tried a new battery?
Solved.
The LCD itself was bad.