I changed the registry successfully and on my first attempt used the headset to activate MS VC. Trouble is once the call has ended it appears that the 'gateway' is not closed, therefore you cannot make another call via your headset button until the device is 'warm booted'.
Is there any fix out there that will address this problem. Does it have anything to do with the BT vs Widcomm stacks.
Thanks :?
I find if I hang up using the headset button (Scala 500), even if the other party has already cleared down, the audio gateway closes and the next press of the button on the H/S reacivates audio and fires up VC again.
Are you clearing the call from the h/s or just letting the other party clear down to release the call?
Dox
MS Voice issues with Bluetooth headset
to be honest I've not really noticed. At times I would clear first, others it would be the person I called.
All I know is once the call has cleared I'm left with an open 'gateway' If I restart the headset it's still 'open'. It's only when I soft reset that it clears the headset.
It could obviously be different across different headsets, but with the Scala, audio stays on after a VC command, and I need to press the button once to close it, and a second time to get the VC prompt back. Something like this...
Press...
<Mic Symbol>
"What is the battery level?"
"The battery level is 23%"
Press... (to close audio gateway)
Press...
<Mic Symbol>
After a call, I usually press the button just in case, and I don't recall it restarting the VC prompt, so I assume it's closing the audio gateway. Maybe it's just my timing and i'm closing it as we say "goodbye", so I always force the call to close down, even if the other party is doing the same?
There have been a few "VC doesn't work reliably" threads, so maybe it does, as long as the h/s behaves as MS expected. If you don't use the h/s, just the phone VC button and mic/speaker, is VC okay then?
Dox
That's the way it works for me with T-Mobile Vario & Jabber 250 HS.
What I would like to be able to do is disable the Jabbers own ring tone as it masks the incoming caller announcment, and I appear to get the
phones own ring tone played in the headset anyway.
Also is there any way to make just the voice louder?
I think the VC announcement voice is a normal system volume (system), and the phone call is the in-call volume (right) sliders on the volume dialogue that pops up when you tap the speaker icon on the today title bar. I don't know of a way to increase the VC annc over the ring tone.
I did find on my Qtek that there's a hidden system .wav file in /windows called LB.wav which appears as an alarm and is a really loud 'boing' sound. I copied it to /windows/loudboing.wav with Total Commander, removed the system/hidden flags and use that as an alert. I guess, in reverse, you could use a sound editor to reduce the level of the ring tone .wav file and then turn the system volume up so that the VC annc (if that's what you want to increase) is comparatively louder than the ring tone...
Dox
qtek 9000 MS voice commander 1.6 handsfree voiceenable !
It doesn't work , but now http://www.jetwaremobile.com/index.htm I have this ?!!!
But the voice down in my pocket PC. I want that Handsfree is only "ON", not "OF" after click?...
qtek 9000 MS voice commander 1.6 handsfree voiceenable !
It doesn't work , but now http://www.jetwaremobile.com/index.htm I have this ?!!!
But the voice down in my pocket PC. I want that Handsfree is only "ON", not "OF" after click?...
Does anyone know if this is possible? I want to make it so when I push a button on my headset it will activate MS voice command So I can tell it to make a call or play a song or what not.
I have a jabra 8040 and just have to hold the botton on the headset until I hear a second beep. about 1 sec later voice command turns on and allows you to do just that.
Obviously the phone dials the last dialed number when the button on the headset is pressed twice. It bothers me, because I keep making pocket calls.
Does anyone know how to turn off the redial function by pressing the button on the headset twice?
On Leo ( with original last rom) i installed VoiceSpeed Dial , but I can not find a way to start this sw when I press the buttom "call" on my headset BT,
the same problem on my Sony car stereo with Bluetooth,when I press the dedicated button, call the last call number. Any solution for this? Tanks in advange.
Try..... press button on headset, hold it down and wait for two bips in headset.
steveianson said:
Try..... press button on headset, hold it down and wait for two bips in headset.
Click to expand...
Click to collapse
thanks friend, just like it does not work, if i press button & hold it on headset BT or Car Stereo, no run VoiceSpeed Dail but call the last call number, ( both devices functioned good with all Nokia phone) but if i hold the button "calling" on the Leo VoiceSpeed Dial run and emits "beep" correctly.
Where can I find information on how to handsfree initiate a call from a bluetooth headset? My understanding is that Android 2.2 Froyo supports this. I have my Plantronics 975 headset synced and working, but can't get voice dial to initiate. Pressing the button on the headset just makes a beep, but doesn't do anything on the phone. Pressing the button twice redials the last number, but it did that on my old G1 with Android 1.6.
Is anyone using a Plantronics 975 with a G2? Does voice dialing work for you?
Thanks,
Tauren
yowzator said:
Pressing the button on the headset just makes a beep, but doesn't do anything on the phone.
Click to expand...
Click to collapse
No idea about the plantronics. With my headset (Sony DR-BT22), pressing the call button on the headset starts the voice dial app (audio through the headset) and a long-press performs a redial.
I figured it out and feel stupid now. But just in case someone else is having trouble, here's the answer...
* Hold down the main button for 2 seconds and voice dial starts (see http://bit.ly/bO0Gvo)
* Double press the main button and redial starts
* If bluetooth is not connected, single press the main button to connect.
* Not sure what a single press does if the connection is already established.
I never tried a long press because a really long press shuts the headset off. I didn't even think that there might be a "short long press" and a "long long press".
On my Moto H17 BT headset, it seems a single press on the button initiates the voice dialer on my G2, and a "short long press" redials.