It worked once.
After that I can't sync using usb (win M5).
The win M5 device does sync perfectly with activesync using BT however it refuses to connect with usb.
On an other pc USB sync is no problem so it must be a conflict on the one pc.
Whó's gona help me out
Related
how to sync xda2 and pc by usb bluetooth i have activesync 3.8
if you mean how to sync the pda with a pc which have a usb bluetooth dongle then read this
http://www.geekzone.co.nz/content.asp?contentid=2417
http://www.geekzone.co.nz/content.asp?ContentId=3163
i need help with my bluetooth connection between my laptop and my mda.
i purchased a kensington usb bluetooth adapter for my laptop to connect to my mda. my laptop detects the mda but laptop is assigning the connection to com port 5 however the mda only allows for com port 6 or 7.
question is how do i make my computer assign a different com port??
please help me!!!
anyone? anyone?
World o' hurt
The only solution I found to this was to delete activesync from my pc -- no mean feat because it is always running, search for "activesynctoggle.exe" -- and delete the partnership and start over, choosing the right com port on the PC the next time.
But that never fixed the ultimate problem, which is that bluetooth would sync once, and then not again until I shut down and restarted my laptop. I finally gave up, as it worked pretty much flawlessly with a usb cable.
I've just bought a laptop with integral bluetooth and I'm hoping that it will sync with bluetooth.
Please help!!!!
I have an Orange M3100 (Hermes 100 /TyYN) which is running WM6 (LVSW Edition).
My device synchronises with my computer running Vista and Mobile Device Center 6.1
I purchased the HTC TyTN Y Cable (http://www.expansys.com/p.aspx?i=145071) to allow me to charge and unit and use the Hermes as MP3 player in the car.
The cable didn't work until I installed the following driver - http://www.europe.htc.com/support/software/htctytn.html
I used this instruction hack to get the driver installed -
http://www.expansys.com/ft.aspx?i=145071&thread=1
I have attached the cab file I used to this thread.
The cable now works perfectly in the car BUT this morning I connected the Hermes with the normal USB lead to my computer and I can't sync. The following message appears on the phone:
To synchronize this device, you must install ActiveSync 4.5 or newer on your desktop computer.
Any ideas?? I need to use synch for work purposes so I really stuck.
There is no uninstall (remove programs) for the driver and I really don't want to reflash a new rom if it can be avoided. (This is the worse case scenario.)
Thanks!
WM6 ROM with Driver
Just a thought is there a WM6 ROM with this driver already integrated???
The driver you've posted, maybe disable the "transfer data check" when power is connected.
The Y cable HAS NOT the pins 4&5 (on its mainboard are 1&2) jointed, so before the driver installation, the pda was unable to charge.
Note: if you connect a cable with pins 4&5 jointed, the sync doesn't work
When you've installed the driver, maybe it has disabilited the "data check" (from USB DATA pins) and "joint check" (pins 4&5) and something goes wrong..
Need more tests, with and without the Y adapter, however all should be ok with an HReset (and you've to joint the pins into the Y cable, that you cannot use to syncronize)
SkizZO
Thanks for the reply.
The Y cable is only used in the car (for audio out and charging) so the Y cable is not used for the computer sync. I simply use the standard computer usb sync cable to synch with the computer. I did however try using the Y cable for the computer sync and it didn't work.
Most bizarrely the computer sync worked perfectly this morning for no apparent reason - I definately didn't change any settings. The only thing is I didn't connect the Hermes to the car enroute home. I wonder does the driver get confused switching between the Y cable and standard USB synch cable - maybe the device requires a soft reboot between switching between Y cable and USB cable?
I'll try it over the next few days and report back on the findings.
I am running Black Edition 3.0.1 and before installing your cab, my y-cable didn't work. I just installed it and my sync with Vista still works perfectly fine as well as the y cable!
So no problem here at all.
Can i connect my phone by bluetooth or WiFi with PC and using PC internet connection to surf the internet on my mobile device which is in the same room as PC.
I have tried with cables (Active Sync connection) and surfing is perfect but im now going this way because it is easier.
I have cable internet (512/64)
PC, Windows XP, SP2, Active Sync 4.5
noname Bluetooth adapter
i can also make some wireless connectivty...
mobile device is:
Qtek 9100, WM 5.0, ...
i installed activesync 4.5 on the computer xp and connected the jasjar to the computer by usb cable but the jasjar can't connect to the computer and the word " connecting " appears on the program activesync but the jasjar can't connect what can i do
ahmedshehata45 said:
i installed activesync 4.5 on the computer xp and connected the jasjar to the computer by usb cable but the jasjar can't connect to the computer and the word " connecting " appears on the program activesync but the jasjar can't connect what can i do
Click to expand...
Click to collapse
Welcome to the forum
Please READ the Wiki
http://wiki.xda-developers.com/index.php?pagename=UniversalFAQ
thank u for your reply but i could solve the problem when i disabled firewall of the desktop computer