Related
Please help me!!!!
this morning my XDA2 has decided that the speaker and microphone sholld be switched off permenently! :x
I believe that it thinks the headset is plugged in - but it isnt!!! (i dont use bluetooth)
I hev tried a soft reset and a hard reset (and also plugging and unplugging the headset)
Please help me - I only like to use the headset when listening to my tunes.
PS i spoke to the O2 data support helpdesk at 60p / min and it took them about 5 minutes to suggest that a soft / hard reset might cure it, otherwise they are clueless.
Is there any way to manually chage the profile from headset to normal handheld????
thanks!
PS my device i nearly 1 yr old - is this the kind of thing that I can expect to occurr more frequently as my XDA2 goes into old age?
i had this problem with my XDA 1. I had no idea what was going on but remembered it working last time i had the headphones in. A soft reset didn't fix it for me either. what DID fix it was ramming the headphone jack in and out really fast. After a few attempts it came back to normal I guess have to 'undo' the problem the headphone caused when it was in there.
:lol: :lol: hehehehe :lol: :lol:
It works!!!!
8)
cheers dude!
Speaker and microphone silent because of headphone
Hello,
Glad you got everything working again..
Just a quick note - I was in a motorcylce accident recently and had my PPC in my pocket, - it was damaged at the the area of the headphone jack, which came loose, and caused exactly the problem you described.
To fix it I had to open the PPC up (instructions are available elsewhere in this forum) and then resolder the headphone socket to the PPC - Now it works fine again.
The upshot of this is that I think the microphone and speaker turining off when the headphone is plugged in is hard wired in - and also the headphone jack is quite delicate - it is only held on to the PC board by the solder connection of about 6 legs, and has 2 very small plastic locating pins, so go carefully with the jamming the headphones in and out.
Also when mine came loose - the back left of the 6 legs broke off - and without that connected back it still never produced sound through the speaker or mic., so it would be possible to permanently wire that in to make sound go both ways.
Mine is mute too did you do anything or did it just fix itself?
It eventually fixed after a couple of hard resets - first one didnt work, but after using the headset for a bit, i got the stuff from O2 to send it back for a repair. when u reset it again the problem was fixed. I reckon threatening it with surgery scared it into submission!
I had the same Prob at every Time who i hit my XDAII, or if it fall down.
After that i must push & hit it again,- sometimes 15-20 Times(!) and after that it works normal. It´s an "cold" point on the board,- the O2 Hotline knows this...
Re: Speaker and microphone silent because of headphone
siezear said:
Hello,
Glad you got everything working again..
Just a quick note - I was in a motorcylce accident recently and had my PPC in my pocket, - it was damaged at the the area of the headphone jack, which came loose, and caused exactly the problem you described.
To fix it I had to open the PPC up (instructions are available elsewhere in this forum) and then resolder the headphone socket to the PPC - Now it works fine again.
The upshot of this is that I think the microphone and speaker turining off when the headphone is plugged in is hard wired in - and also the headphone jack is quite delicate - it is only held on to the PC board by the solder connection of about 6 legs, and has 2 very small plastic locating pins, so go carefully with the jamming the headphones in and out.
Also when mine came loose - the back left of the 6 legs broke off - and without that connected back it still never produced sound through the speaker or mic., so it would be possible to permanently wire that in to make sound go both ways.
Click to expand...
Click to collapse
Same problem from yesterday! ..it is the jack ..if I move it down with the stylus ..the audio returns to the speaker..uff..
I don' wanna open it and solder.. too lazy..lol
Dead speaker
I have the exact same fault as described
only after losing about 3 calls did i realise it was the xda2 not some nutter that wouldn't speak!
fixed it with putting the headphone jack in then out etc..... 15 times!
it would seem like this is a design fault! as it is coming up to year for the xda2 should we organise o2 to recall the xda2's and repair this fault!
So I have this problem - only thing is Im in the USA at the mo and didnt bring my headset - is there any other fix as Im kinda stuck ?
Nigel
Husband had same problem.
Changing ring tone fixed it. Don't know why. Don't know how, but it fixed it!
Re: Husband had same problem.
guest said:
Changing ring tone fixed it. Don't know why. Don't know how, but it fixed it!
Click to expand...
Click to collapse
I have the same problem, after calling with a headset, now my sound has gone ( Out of complete my XDA II ). Changing the ringtone didn't work for me...I am going to try to test the plug/headset way!
After 12 times my sound came back...so it worked for me!!! :lol:
It's the headphone Jack!
The problem is with the headphone jack!
I have had the same problem for months, sometimes it would stay without sound, always when I dropped it. Usually it returned after 1 or two days, but the last time I dropped it it seemed to be final... I've had no sound for more than a week - I'm using it as a PDA...
Reading the posts above, I decided to insert the pen in the headphone socket (as I don't have the headphones here with me), move it around carefully, and it wroked! Right now, it feels like magic, but that's it - I will probably have to get it fixed permanently, but for now it will do!
well i always have that problem in my phones... because i always hook them in my car stereo by the headset output.. and constant using of the output somehow makes the insides of it dirty.. believe me its dust.. a tooth pick would be very effective as it takes the dirt away.. blowing in sometimes work...
mine is also soundless
i was able to get some dust out of it....
but it won't work....
i don't have the nerves to ramm the headphones in....but isn't there another safer way to fix it....
plz let me know, (hard resettet 5 times.... won't work..)
btw, i tried to put some new updates on it....
but i can't find any, (i searched, but couldn't find anything...)
device information:
Rom Version: 4.01.12 ENG
Rom date: 12/22/03
Radio Version: 4.21.00
Protocol version: 32S54
It's a little bit out of date...that's why i need new ones (i think)
h0t_sh0t
bringing it to the accredited local shop would be the safest way.. maybe there's more dust in there.. you can also rewire it again.. like opening the PPC and soldering back some pins.. (if some pins broke off ..)
Same thing happened to my jam too.
Problem is; there's a little switch in your headphone socket, when you plug your headset it turns off the external sound, and when u unplug it should normally turn on the external sound. But if the switch is locked, it does not recognize that u unplug your headphone.
My solution is, plug-unplug your headset's plug (or something thinner is better) several times in different angles carefully to your socket try to touch the switch while your're playing something. Till u hear the external sound.
Mine is ok now.
(Sorry about my bad English)
I had the same problem. I sprayed a little WD-40 on the tip of my headphones... pushed it in and out for a couple of times and viola!
first question...
what's wd-40??
second question...
when i put my earphones in, i can hear everything...but I can't speak...
but when I unplug my earphones, and I scream in my xda... I can hear a little bit what i'm saying when i plug my earphones back in.
but it's very crappy sound, and when I slam (not to hard of course) my xda with the mic onto my desk (while recording) and i listen to it again, i can hear the drums....(the slamming) but I can't talk in it while using my headset...
has anybody had this before...?
third thing...
My uncle bought the XDA in Singapore about 2 years ago (when it just came out) so when i'd like to bring it back.... i'd have to fligh all the way to Singapore. (does anybody know a good shop/store who sells/repairs XDA phones...??? or is there anybody who can do this....?
thnx for all the help
h0t_Sh0t
Hi,
My exec is stuck in headset mode, it appears to think the handsfree is still plugged in and will only use the headset mic and earpiece even if not plugged in. I've tried a soft reset to no avail and i really dont want to do a hard reset as i have no way of backing anything up at the moment.
Any suggestions?
thanks in advance
Brodie
This is a fault that goes all the way back to the original devices...
The way to fix it is to get your headset jack, and try various ways of quickly but forcefully unplugging it. Happened to me the other night and eventually I managed to force it to recognise the headset was removed and it came back out of the speaker.
Cheers
Ant
sorted now, not sure if it was unplugging or not but i made & recieved some calls and unplugged it and it works!
thanks for the speedy reply and solution.
cheers
Brodie
I also have this problem today....but I dropped my xda exec on the ground and then all the sound is gone.....only headset and bluetooth are worked....
I think I damage the phone somehow.......
But I will still use it...
Anton.Valleyman said:
This is a fault that goes all the way back to the original devices...
The way to fix it is to get your headset jack, and try various ways of quickly but forcefully unplugging it. Happened to me the other night and eventually I managed to force it to recognise the headset was removed and it came back out of the speaker.
Cheers
Ant
Click to expand...
Click to collapse
Thanx Anton. My XDA experienced the same problem and I was veeeeerrrrrry sad about it.
Then I came across your suggestion and, BINGO! It worked.
*Sorry for the duplicate post*
This just started happening on my JasJar today (system audio returned after poking the headset in/out a few times), after 11 months of use. Does this get worse over time? Should I bite the bullet and try to get Imate to repair it?
Please advise!
Damn it, I've got the same problem since yesterday
I can hear calls in handsfree mode (using the built-it handsfree mode) and with an earphone plugged in but not through the speaker besides the display.
Strangely, the internal mic works well (I mean, the called person can hear me). Is it the same problem you're talking about or has my speaker just collapsed? :?
.ox
EDIT: I've noticed that only the speaker above the display seems to be muted. The one on the backside of the display and the two speakers in the main body (when using handsfree mode) work. So I guess, the speaker's dead, isn't it?
2nd EDIT: After plugging a headphone in and out about 20 times and applying pressure on the display receiver it suddenly started to work again. I'm not sure what was causing this problem but even a hard reset didn't fix it so I guess it's a hardware (or firmware) related issue.
Same Problem
After working fine for months, with and without the earplug, my MDA Pro has started do the same thing--it's stuck in earplug mode. I've tried plugging/unplugging the earplug for about five times in a row--didn't help. Do I really have to do this 20 times? Jeez--I'm afraid of messing up something else. Could there be another solution? UPDATE: I just now tried plugging/unplugging 20 times--no help!
OK, the solution is the same as that for the loose USB port--send the MDA Pro to the fine folks at Pocket PC Techs and let them fix it. They replaced the earplug jack and got the unit to work perfectly with and without the earplugs. $75 plus shipping. They misplaced my stylus, but sent me a new one right away. I'm very happy with their service.
I've had this kind of problem with a Nokia 8310 which I've carried for three years. I believe it is a physical problem with the headphone socket which may be caused by lateral force on the jack while plugged in inside a pocket. Wiggling and unplugging the jack repeatedly makes the phone socket work properly. There is a small switch inside made out of a metal spring. All you need to do is wiggle it.
The phones which go silent after being dropped may be a different matter.
Hi there
This is my second O2 mini-XDA. The sound on the phone doesn't seem to want to work anymore. I can't hear alarms, hear anything making phone calls. It happened once before with this phone and seemed to go away by itself. I've got some important data on the phone so I'd love to not have to send it in. Anyone have any ideas about how to sort it?
Cheers
immy
Try if you got the sounds thru a headset..
It's possible that the microswitch inside the headphone connector is stuck.
I had the same problem. When I inserted mij headphone a few times it was solved.
The microswitch is for switching of your speakers and activate your headset.
Good luck
volume bubble
tap volume icon on start bar and turn the volume to on!
I had the same issue with the original Imate XDA. There is an issue with some of the HTC phones in which the cable of the speaker is broken. The easiest way to check it is to connect a headset and then see if it is working or not. If the sound is still not working, then you will need to replace the D2A audio chip. Is your phone under warrenty?
Regards,
A very common problem - had the same problem (fortunately, my PDA is still under warranty and, therefore, it was repaired for free). The chip that switches between the wired headset and the three built-in speakers just died and had to be swapped.
Some other people also state this can also be caused by using the wired headset, which causes shortouts when you insert / remove it.
Hi all
It would be great if you shed some light on the problem
Xda exec had a fall!..since then no sounds at all, phone won't ring or won't play music...but has sound if i plugged the headphones in
Any theories/ideas what might have gone wrong...& possible solutions..
any help would be appreciated...thanxs
sound failed on xda exec
i also had the same issue but my handset was replaced as it was within 28 days of getting the handset
i never did manage to find the exact issue
when your handset fell did it have external sound / handsfree plugged in at the time
about the only thing that made any sense with mine was the possibilty of the micro switch / contacts of the externl audio jack being damaged
dont know if any of this info helps you at all but best of luck getting it sorted
Still no explanation for the no sound problem Xda Exec
Does anybody find out allready what's the problem with no sound on the Xda Exec.
I not speak about the problem with the external audio jack.
I can make cals like normal, I only can not play music or listen if somenone is calling me.
Thanks
its hardware problem with universals audiojack .. just open device ..remove board . plug headphones ... and see on connector /.... in most cases no sound issue cames from third pin of jack (thst pin detect plugged headpnones .. if it disconnected device plays in headphones if connected device plays on builtin speakers) if near end of it ...
a may advice you more deeply but i didnot have proper photo to explan in his basis..
just give me HI RES PHOTO OF BOTH SIDES OF YOUR MOTHERBOARD.. i explain what to do
mo3ulla said:
its hardware problem with universals audiojack .. just open device ..remove board . plug headphones ... and see on connector /.... in most cases no sound issue cames from third pin of jack (thst pin detect plugged headpnones .. if it disconnected device plays in headphones if connected device plays on builtin speakers) if near end of it ...
a may advice you more deeply but i didnot have proper photo to explan in his basis..
just give me HI RES PHOTO OF BOTH SIDES OF YOUR MOTHERBOARD.. i explain what to do
Click to expand...
Click to collapse
Thanks for your post.
You are shure that this willbe the problem, because I can make calls without the headphone. I was thinking that in the case that the connector gives the problem, I should also not be able to make any calls without using the headphone.
Anyway I was going to open my friend one day, to look what's up.
problem may be repaired in home in 10mins
you need
hands
brain
tools to open
1 needle
do photo .. i say what next
mo3ulla said:
problem may be repaired in home in 10mins
you need
hands
brain
tools to open
1 needle
do photo .. i say what next
Click to expand...
Click to collapse
Ok, here we go.
We have hands, tools ( a hammer ) and 1 needle.
I think I forgot something, but...
I think the problem, when the problem is hardware,
is that when you put the headphone jack, the top of the jack he opens the microswitch what you see at first.
Ofcourse when this switch he stays also open when you take out the jack, than you have a problem.
And yes with a needle you can first open the contakt and than you can dress littlebit the position of the contakt.
I have only 1 problem on my tel, this switch is closed as well, when I take out the jack. The problem is not this switch.
here we go
Correct, I am shure that this is almost always the problem.
In fact the switch is closed in normal position, and he goes open when you put the headphones.
When he not close as well automatic than, you have a problem.
But in my case it is really not this switch, so I am still looking for the reason why I not have sound.
hi all
i have same probelem like you
my friend using my device for weeks and when she give it back to me i have no sound from my device & even from headset i call the i-mate center the girl told me maybe your jack is dameged but when i sent it to suport center they told me your flex cable is dameged by wrong rotating your device and we haven't that yet ....
they sent it back to me and after some day my screen shows nothing then i buoght a cable from ebay an change , now i have voice sound screen
&....
like before
i hope these usefull for you
This was exactly my issue, under that pinkbox you marked is the tiny tab that makes or breaks contact with the internal speaker. Because my headphones break the contact, this tab after much use was stuck in the open position even after the headphones were removed. When I did the procedure you mentioned magically, sound..wow. I am extremely greatful for your troubleshooting skill.
Thanks a million mo3ulla.
If only i had this fix 2 phones ago..hahhahah.
lambrechts said:
Correct, I am shure that this is almost always the problem.
In fact the switch is closed in normal position, and he goes open when you put the headphones.
When he not close as well automatic than, you have a problem.
But in my case it is really not this switch, so I am still looking for the reason why I not have sound.
Click to expand...
Click to collapse
Hi lambrechts,
Did you manage to find out the reason?
i have the same problem, my device fell, but i didn't notice the problem until next day (i didn't use it) so i'm not sure if it is because of the drop.
I will open my device and check the Jack pins, but i want to know if you got any fix for this.
mo3ulla said:
here we go
Click to expand...
Click to collapse
hey mo3ulla, did your method work after repeated use of the headphone port? did it get stuck again any time after you fixed it?
just asking cause i have this problem on my 9000 and haven't opened it yet so i don't want to open and close it repeatedly
thankss
I have this problem aswell. But I inserted a fork and twisted it around a little and now it works as it should again.
Bumping this thread. Should be a sticky or in the wiki.
Anyways,
I tried the pin trick back when I posted here, it worked but it wasn't permanent. Instead I put a crumpled piece of post-it note above the pink dot in the picture and it worked, up until recently. Does anybody have a method to bend the connecter back down? I'm probably not using the needle right, I press the pink spot, but it pops back up.
Ideas?
twisting the pin really helps. thanks for the solution. I tried to insert my headphone again and the pin always stucked. I'm trying to find a permanent solution for this. Maybe put something to push the pin to be connected everytime I remove the headphone...
I hope this helps. I found it very useful to my Dopod 900. I tried to connect my headphones (sounds works on my headphone) then I disconnect it and sounds works on my stereo/speakers.
*Please do it carefully in pushing the pin upward from inside the hole. Just push it a little bit just enough to touch the upper pin..
additional tip: after you fixed your device, try to install SRS Wow for great audio experience
Quick Fix
I found that if you apply a little pressure between the base and just above the send key this seems to work, I tried this tonight and will report back if goes again.
luckyearl said:
Hi all
It would be great if you shed some light on the problem
Xda exec had a fall!..since then no sounds at all, phone won't ring or won't play music...but has sound if i plugged the headphones in
Any theories/ideas what might have gone wrong...& possible solutions..
any help would be appreciated...thanxs
Click to expand...
Click to collapse
could be a damaged PCB motherboard, or lose connetion for the sound chip!
you could try fixnig it, or replacing the motherboard.
a new motherboard could be bought off E-Bay US for a cheapish price =]
genspeed said:
I hope this helps. I found it very useful to my Dopod 900. I tried to connect my headphones (sounds works on my headphone) then I disconnect it and sounds works on my stereo/speakers.
*Please do it carefully in pushing the pin upward from inside the hole. Just push it a little bit just enough to touch the upper pin..
additional tip: after you fixed your device, try to install SRS Wow for great audio experience
Click to expand...
Click to collapse
Not sure if the srs wow will work, last time i tried it give lots of other problems like; mute the sounds, works great after you press the power button on and off, then no GPRS and Internet conectivity but if you have worked around those probs pls give an idea?
hi, i got an imate jamin and i need to replace the audio jack were the handsfree pug in, do anyone know where i can find to buy this part please or if anyone had the same problem how did you solve it.
thanks guys!!
Dodgy Audio jack
My audio jack plug works fine BUT when I unplug the headset, the phone stays in headset mode i.e. no sound from the speakers. If I plug/unplug the headset a load of times it eventually goes back to normal.
Any ideas. My solution is never to use the audio jack!
Audio Jack
I've had two M600's which have done exactly the same thing, both replaced by Orange, I've now upgraded to an M700 and unlocked the old M600 with a PAYG sim and guess what that one has now lost speaker sound so that three with the same fault and this M600 has never had a headset plugged in.
Has anyone else had similar problems?
i had the same problem othillo before it broke so be carefull cause your is about to brake too, i mailed imate and they said the only way to fix it is to send it to them in dubai.. not relally keen to send it there .. but till today i havent find ther part any where it seems that imate dont send out parts ... as soon as i find an alternative i will post it here..
Is this problem caused by the connector itself or is it something else? If it is the connector I can buy a new one at the local hardware store and modify it a little bit to make it fit in my S200, probably going to replace it with an 3,5mm jack if that is possible...
it is caused by the connector in fact htc the original makers of the prophet on there new models they changed it to a usb connector for the handsfree i changed my connector many times with regulas 2.5mm connector but the sound doesnt work properly. what it does it comes out with out bass then when you push the talk button on the handsfree sound comes out good. another thing i noticed is if when you insert the jack plug in the connector and you pull it out a little bit the sound comes better and the talk button works, i know for fact cause i tried it that its not from the handsfee cause i tried it on another device and work properly. the actuall connector for them is different from what you find to buy even if you plug in normal 2.5mm headphone sound doesnt come out right . if you manage to make it work and modify the connector please post it here so who got the same prob like me can have an idea how to fix it... thanks
Audio Jack
Here is what the problem is:
Audio jacks have what is called a normally closed contact. Each contact point actually has 2 parts. In the closed (no headset) the 2 part of the contact point make contact (shorts). This enables the signal to pass through the jack to the phone speaker. When you insert a headset, the 2 points open (break contact) and signal only goes to the headset.
I'm talking from experience as a sound engineer for over 30 years and this is usually the problem 99% of the time when it comes to these type of jacks. One of the contacts (usually the ground when no sound or mic at all) breaks or can no longer "spring" back. I haven't opened mine yet but fully expect this to be the problem.
audio jack
hi jsapper, i got what you saying and your absolutly right .. the thing i replaced mine 2 times now been done by a technician who fixes phones/pdas the thing with the connectors i replaced the device doesnt work properly sound comes out with out the bass and the talk button doesnt work .. i guess that the original part got some extra connectors or most probably the pins are switched around..
do you know if there is any special connectors for them...
I have a similar pb with my S200:
After running tomtom during 2000km installed on my motorbike w/ a 2.5mm headset, sound seems to no work anymore (neither back or ear speaker), I suppose that vibrations against jack connector are responsible.
With a bluetooth or wired headset sound works.
I have soft/hard reset, upgrade to last WM5 rom, upgrade to WM6 rom, I have tried to get in/out a 2.5mm jack connector without any result.
The ring facility is working (w/ or w/o 2.5mm jack connected), so I can say that the back speaker is working.
I am looking for a solution too...
nb: I have my back speaker + screen replaced one time after 2months.
Dean.
Have you try resolder the Connector?
it was to damaged to be resolded
Hi everybody,
I aswell have this kind of problem from time to time.My solution is quite simple.You have to use the original 2,5" jack with the 3 black "dividings".(sorry for my english) This solution reduced the problem dramatically.If the problem starts now, just plug it in and out a few times and it should work again.
Cheers
Phone Jack is a mechanical mess ...
Same prob, used the headset, rear speaker dead. I opened the prophet, unsoldered the jack and found it misconstructed.
The body of the jack is plastic and not capable to withstand the forces of a plugged in headset.
There are two integrated switches - which - when headset is unplugged are closed and deliver the signal to the speaker. one of the switches does not close anymore when the headset is unplugged. My first solution was to unsolder the jack and bridge the contacts 2 and 4 as welll as 3 and 5.
The rear speaker functions now and I can use the phone.
Next step will be to find a jack solution on the market to finally solve the problem. I will keep you informed!
thanks buzzi will be looking in here... for your post!
i had the same problem with my audio jack and i searched many forums for a solution. the only thing i can say: if you really want to use it and you want go back in normal mode after unplugging, take a little needle. if you look at the audio jack (USB is left to it) you have to stick the needle in the right side of the jack somewhere an search for a little contact (the first time hard to find, the second time easy) and try to push it a bit to the left. so the prophet goes back in normal mode. it sucks but i didnt find another solution...except for buying a bluetooth headset and use software to hear music over that (for mono headsets u can use a programm calles BTAudioToggel, but make sure u use the Toggle software, because there is another one called BTAudio, it sucks because it costs money and doesn't work for me so well)
Greetz
Friends,
My prophet has exactly the same symptoms. However, I opened up the phone and carefully examined the jack. It is crap, sure, but at least on my phone it is not at fault. I tested with a continuity meter and the contact mechanism was working perfectly. Those who tried this measure without success read the following thread:
http://forum.xda-developers.com/showthread.php?t=281331
In my case it is definitely a problem with the speaker, and it seems to be eqaully common. It seems that there is more than one problem dogging the speaker of ths model.
mine's got the small contact switch problem.
it started last night! SO Annoying. Plugging a friend's original 2.5mm adapter in and out solved it temporarily. Then it went again! I have only got a 3rd party 2.5mm plug, and it took me ages to trip the small switch back with that. I have now got a BT headset on order.
Can't wait for the newer design HTC headphone adapter as I have had this problem with 5 different devices! (Tanager, Typhoon, Hurricane, Tornado and now Prophet.)
would agree with hybrid the needle trick fixed it ran media player so i could tell when it was working again. it was mentioned before that using the 2.5mm adaptor with ibky 2 rings as opposed to 3 causes this problem. I can identify with this as i have been using my dopod h/free with no problems for months i use the adaptor to plug in my headphones one time and get a eap of issues!
i will adapt a h/free to plug in some nicer headphones!
Can i use the USB connection as a handsfree port on my prophet?
Cheers
Hi, Prophet's USB is not a USB hub and thus not usable for connecting external devices - only way is bluetooth ...
thanks buzzi