Help please, this morning i switched my mda on and all i see is red, green and blue color bands on screen. I have tried soft resetting it but no luck.
thanks
Attaching image if that helps...
Please can somebody know what is happening...
Thats the bootloader mode. Try soft resetting your device (poke its bottom )
have soft reset a couple of times but no luck...
hard reset?
have you been messing with the rom? flashing it or the like?
Try hard reset. Poke and hold camera button. And, while you are at it, check that your record button is not stuck which made you go into the boot loader mode.
Related
Hi Guys
I've done searches to find a solution, but I can't find any.
I flashed my gene (have done many times before). Somehow got things mixed up. And now it doesn't even want to go into bootloader.
Try rebooting, power button does nothing. When I hold "camera" button and reset the green & red buttons flash then nothing.
I have tried soft & hard reset, nothing works. Screen just stays blank.
Please help, I'm really in trouble.
Regards
Celliers
Sometimes this problem happens with me. You have to remove battery and press the power button sometimes (without battery), then put back battery and power on your gene. After this, try to go into bootloader mode and flash another rom.
i installed the Ezinput from http://forum.xda-developers.com/showthread.php?t=536215 for wvga... i installed it, then it said a reset is required to finish intallation. after the reset, it went to the touch diamond 2 boot up screen, after that was over, then screen displayed nothing. its black, and usb does not respond when i connect it to the computer. any ideas? i already tried the reset using teh red button. took out the memory card, where i install the .cab, still doesnt work. any help would be greatly appreciated.
If it's totally unresponsive from boot, hard reset it. Hold Volume Down and press the "red button" to reset it. It'll go back to factory settings.
same problem here, help needed!!
i tried to restore it to the factory setting using volume down and red button but when the phone flashes it shows me this three color screen with the message "serial" on the bottom side of the screen, any ideas on what should i do???
thanks in advance...
To perform a Diamond 2 hard reset
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see a message on the screen.
alwaysrun said:
i tried to restore it to the factory setting using volume down and red button but when the phone flashes it shows me this three color screen with the message "serial" on the bottom side of the screen, any ideas on what should i do???
thanks in advance...
Click to expand...
Click to collapse
What you did is boot in "bootloader mode"; in that mode you can try to flash again the original ROM.
thanks
thanks a lot guys, your help is well appreciated, i finally managed to flash the phone bios and now trying to install the original rom, thank you again
So I installed a new version of SPB shell on my atrix.
I rebooted my phone, and now its stuck on the "M" boot logo.
WHAT DO I DO!!
thanks in advance!
The first thing I would probably try is removing the battery for a few seconds and then try to boot again.
Yeah i did that. Now i am doing a factory reset through the boot menu by holding volume and power button at same time.
I believe the first thing you DON'T do is factory reset in a soft brick situation.
well it worked. so maybe it wasn't soft bricked?
Today my friend give his HD2 to me for fix it.
When try to turn on this device, it stuck on htc logo. then i try to soft reset it with press the red botton near the simcard. try to turn on it again, but it still stuck on htc logo.
so what should i do for fix it?
it seem there is no ROM.
Anybody know how to flash RUU without turn on the device?
Thanks Before.
Maybe you will have a look on this tutorial: http://forum.xda-developers.com/showthread.php?t=609477.
Have you tried hard reset using vol and power keys?
Hi everyone,
Could anyone please help me?
I tried to Hard reset my phone (Lenovo Phab 2 PB2-650M), but then the power button won't work even pressing the Volume button down don't work too. In the end my phone just turned on and nothing happen, also with the Factory Reset in settings, once I press the Factory Reset Button and yes it will restart then boot again (same scenario), then will turned on and NOTHING HAPPEN again. :crying::crying::crying::crying::crying: Please help me fix my phone. I need it badly. Thank you in advance!