I have been using this patch with my Itech R35 headset for a few months now. I noticed when I try to connect in the morning before I go running, it seems like it won't connect with WMP. I turn off BT and turn it on, but nothing seems to work until I do a complete soft reset. This is turning out to be a pain in the ass. Does anyone know an easy way to connect each time? I am also using an Imate Jam. When it is connected, it works great. Please help.
Related
I am using QTek 2020 with Jabra Freespeak 250 bluetooth headset (I am not sure if this is relevant). I have just noticed that my device is no longer turning off by itself when running of battery power as specified in the settings. Does having the bluetooth mean that it can't turn off by itself?
same problem
I am using a Bluespoon digital, and have the same problem. However I don't know if it has anything to do with it since my device has so many problems.
Hi,
I´m using a Qtek2020 with the Jabra250.
I have some times the problem with the device not turning of.
I have tried this and it works for me:
1-Close Bluetooth
2-Change turn of device time to a diferennt time. If you have 3 minutes change to 2 or 4.
3-Wait until the device turns of.
4-Turn the device on with power
5-Activate Bluetooth headset.
After I have done this the device turns of again.
Hope it will works for you both.
Regards
Josef
I have been having some problems with my bluetooth just not picking up. Device is Plantronics M3000 and after I rebonded it with the XDA2, is fine. If I then turn off the headset, turn off bluetooth on the XDA and put in standby, leave for 10 mins, finally turn everything back on, the headset is not picking up calls. Bluetooth is set to ON and headset mode is enabled.
Is it possible that an application I have installed is affecting the bluetooth? I performed the ROM Upgrade but can't really remember using bluetooth before now and then, so can't confirm ROM Upgrade isn't responsible.
I will attempt hard reset on sunday, but has anyone else got any suggestions?
hi ppl
i use an austrian mda2 w/ ROM 1.6.00GER and ExtROM 1.60.07 together with a parrot ck3000 handsfree in my car.
i use the original bt stack w/o ANY changes.
making calls and taking calls is no problem at all and works most of the times.
the problem is as follows: when i enter the car, bt turned on, and also profile says "BT Headset ist eingeschaltet (means bt headset is turned ON)", and the n i want to place a call, the call is not routed over the handsfree. explanation is simple: when i change back to "today" - bt is turned OFF !!!
so my conclusion: everytime bt is used for the first time after disconnetion from the handsfree, it just turns OFF when it should connect. after i turn bt on by hand again it works w/o any problem. ('till i come back to the car of course - and everything starts again)
this is very annoying....
so has anyone any hint what to do? i wouldn't really mind updating to an english rom - if i just knew that that does work.
thanks,
servus ize|man
when i use this one
http://bluetooth.i-networx.de/index_e.html
my device turn bluetooth on when i call even though i dont have a bluetooth headset maybe it'll help you
thanks rudegar
i know that stack by TOWA. unfortunately that does not work at all here
i'd love to use it, but w/ this stack my handsfree is reconized sometimes, sometimes i have to pair the devices every time i start my car, and i can NEVER place calls with the combination mda2 with networx bt manager installed.
maybe someone has the same experiences and can report them
servus ize|man
I have a jade working with a BT110 it answers the call fine but after the call the headset apears to turn off which it is supposed to do but the phone thinks that it is still connected so you have to turn soft reset the phone before you can make/recive a call and hear it via the handset.
has anyone else had this problem or could it possibly be the headset rather than the phone?
Tom
paperclip69 said:
I have a jade working with a BT110 it answers the call fine but after the call the headset apears to turn off which it is supposed to do but the phone thinks that it is still connected so you have to turn soft reset the phone before you can make/recive a call and hear it via the handset. has anyone else had this problem or could it possibly be the headset rather than the phone?
Tom
Click to expand...
Click to collapse
My experience - I use Jabra BT. The BT does not switch off after call is disconnected, until you switch it off. And the phone always thinks that BT is on (even when the BT set is switched off) until BT is disabled using the comm function.
I tried another Jabra headset last night, and although slightly better behaved it still didn't release the phone when turned off?
does anyone use a BT headset with the jade that works properly? what are peoples experiances.
anyone know what it is about the jade that makes it not work right?
Hi
I have the T-Mobile G2 Touch and a Motorola S9 headphones. Using the Origianl Stock T-Mobile ROM i have had no issues with bluetooth.
BUT
using the generic 2.73 ROM i have issues with connecting to the headset
It will connect, then instantly disconnect, then try to connect again, at which point it fails to connect properly
To Reproduce:
Using a HTC Hero & 2.73 ROM
Pair your S9's with the Hero
then Turn off the S9's and Bluetooth
Then turn on Bluetooth, and the S9's with the Bluetooth Settings up
you will see it say "Connected with Media", "Paired but not Connected", then "Connecting......." at which point it will fail
I have tried all the different radio versions to make sure it isnt a issue with the radio, but the same problem prevails.
Does anyone have any ideas on how to fix this issue? or what is causing it?
I also had issues with an unlocked Hero and a Sennheiser MM200 headset. Worked perfectly on original rom, but very fiddly to setup with the 2.73 rom.
The only way I can get them to work properly with the phone is to:
1) Make sure headset is turned off, as well as bluetooth on phone
2) Turn on headset
3) Then turn on bluetooth on phone
Headset connects as normal - any other sequence doesn't work.
I have tried this, and it doesnt seem to work. I have been trying it for the last hour.
While in Bluetooth Settings it says its connected with media, then is disconnects, then it trys to connect again, and then it just says "Connecting.........." for ages
The Headset light flashes as if it was connected.
I also had problems connecting MM200. I could connect it, but then it kinda stuck when i was pressing play button.
But then i decided to check my old sony ericsson bluetooth headset - it was working normally. And after that the MM200 also was working. One wonders.
Still i've noticed some stuttering problems when song starts. And it seems to start with faster tempo and then slow down after 10 seconds to normal speed (could be related to that stuttering? Trying to compensate for the lost time or something). No issues when i'm listening to wired headphones - so it must either something with hero bluetooth or MM200.
I have to check how it works with my old headset, but i'm kinda afraid of having MM200 connection problems again.
Ok
i will keep playing around. i have some CX-300II coming next week so i have a backup plan if i cant get the bluetooth stuff working properly
Thanks for your help
raywiper said:
I also had problems connecting MM200. I could connect it, but then it kinda stuck when i was pressing play button.
But then i decided to check my old sony ericsson bluetooth headset - it was working normally. And after that the MM200 also was working. One wonders.
Still i've noticed some stuttering problems when song starts. And it seems to start with faster tempo and then slow down after 10 seconds to normal speed (could be related to that stuttering? Trying to compensate for the lost time or something). No issues when i'm listening to wired headphones - so it must either something with hero bluetooth or MM200.
I have to check how it works with my old headset, but i'm kinda afraid of having MM200 connection problems again.
Click to expand...
Click to collapse
I think the speeding up / slowing down and stuttering is more to do with the Hero - I have tried the headset connected to a laptop and there is no problem whatsoever. Hopefully the next Android update will improve the bluetooth problems.
not compatible with new mazda 3
Well the hero is probably the best phone ive had and ive had many many phones over the years including the jesus phone which was pants.
Well ive just bought a new mazda 3 and unfortunately the hero does not like connecting to the car via bluetooth. tried all sorts. sometimes it works but usually only for a couple of times and then manages to lock the car radio up.
So its bye bye hero for me as i need a compatable phone for my car. looks like its back to nokia...shame as i really love the phone