MDA Overclocking - OmapClock vs. XCPUScalar? - 8125, K-JAM, P4300, MDA Vario General

Has anyone seen or noted any differences between Omapclock and XCPUSCalar for overclocking the MDA? Obviously XPCU is not free, but I'm curious if anyone has gotten better/different results between them. The newest version, 2.93, claims MDA support.

I just checked the website and it only works with the MDA Compact which is different than the MDA Vario.. so XCPUSCalar does not work with HTC Wizard devices..

MDA Vario is not using an XSCALE processor is it?

XCUScalar
We have no choice but to use Omapclock. Wizard uses TI OMAP processor !! not Intel Xscale.

I'm not arguing, but I'm confused why ARM apps run on the MDA them. Is it an emulation mode, whereas an overclocker has to be direct for the specific CPU?

fbueller said:
I'm not arguing, but I'm confused why ARM apps run on the MDA them. Is it an emulation mode, whereas an overclocker has to be direct for the specific CPU?
Click to expand...
Click to collapse
The Texas Instruments OMAP & the Intel Xscale are both ARM based processors.

you are right but changing clock of processor requires cpu specific code. omap does not equal xscale! it is a complete different hardware structure (which is of course able to execute arm-code).
hope this explains why xcpuscalar does not work on omap cpu and why omapclock does not work on xscale cpu.
regards
peter

peter_altherr said:
you are right but changing clock of processor requires cpu specific code. omap does not equal xscale! it is a complete different hardware structure (which is of course able to execute arm-code).
hope this explains why xcpuscalar does not work on omap cpu and why omapclock does not work on xscale cpu.
regards
peter
Click to expand...
Click to collapse
Cheers. I do realise that though. I was replying to the previous post asking why ARM apps in general can run on the MDA, by saying that the OMAP & Xscale are both ARM, therefore ARM apps can run on the MDA.

sorry for asking a dumb question but whats the advatange's of over clocking....my Vario runs at 195 tops and I've never seen it run slow....even after playing games and 6hours of mp3 music playing...
if you overclock the speed doesnt that mean the phone gets very hot and may cause internal damange to delicate chips etc?
:?:

If you don't have a problem with the device running slow, then I don't think you need to worry about overclocking.
I use my Wizard for all kinds of media and I find that overclocking it helps performance in that respect.

your lucky, most of us have to overclock to make the thing useable
must be the tmobile crap cos mine takes about 2 minutes to boot up as well :x

well my boot time takes ages cos of spb weather+today plug ins and windows media plug ins....but i can use my device and the only thing that slows it done with me noticing is active sync...

I brought this up.... because the latest XCPUScalar 2007 supports OMAP.
Wondering of anyone has tried it. If i'm not mistaken, i think it has a feature wherein it will step-up and step-down the proc based on load.
http://www.immiersoft.com/index.html

I am using XCPUScalar 3.0 and it is quite good. It is more user friendly than Omapscaler.
It can put cpu meters both on tray or taskbar, so you can see the current speed and tap to make changes.

Related

Game Compatability

I want to try out a few games on my XDA2. Any recommendations?
Also what about compatability. I haven't seen the XDA2 listed as working with anything yet, but I'm sure that's not the case. For example with Doom, there's the following builds listed:
Doom4CE for Casio E-100/105/500
Doom4CE for HP Jornada 820
Doom4CE for Casio E-115,125, EM-500, EG-800
download Doom4CE for Compaq iPaq
Which one should I be looking for? In general, what PocketPCs are software compatabile with my XDA2.
Cheers,
Phil.
ipaq since i'm not too sure that those others are made for the arm cpu which xda and ipaq share
I just tried the RaymanUltimate demo and that was the ARM version and it worked fine. A little confusing since the user manual has the XDA2 having an Intel XScale 400MHz CPU. Is the manual wrong or are the Intel and ARM CPUs compatable with each other?
I'll try the iPaq version of Doom as see if that works.
Cheers,
Phil.
well once there were a company who made small riss cpus called arm
then intel went and bougth them and after awhile they changed the name of the cpu line from intel strong arm (Mhz) to XScale
lucky for us they remained code compatible
sure it's pretty confusing
and i'm sure there are some programs which take advantage of newer instructions of the XScale which will not run on arm but all arm programs should run on the XScale
of cause not all pocketpc 2002 works on wm2003 but games are mostly made from pure cpu instructions and does not use the winCE API so they are ok most of the time (excluded quake2 pocketpc which only works on 2003)
well why not get quake1 and 2 they are more impressive then doom?
i have quake1 installed and it's running just fine havent gotten around to messing with quake2 yet because it takes up about 32MB :/
also had wolfenstein running ok
but imho then it's near to imposible to control when one is used to
the mouse and keyboard combo
maybe if the ati media chip in xda2 become popular games will be made for it and will not run on xda1 and we'll be in a place like pc's and videocards

processor type problem

A problem I'm encountering in downloading BtnPlus (to program the buttons w/ multiple functions) as well as many other programs for this Qtek is that the installers for ARMS/MIPS/SH3/CAB don't seem to work. My device says it has an Intel processor. How do I deal w/ this?
arm and xscale are intel
and are called arm most of the time
because xscale is what intel started to call the
arm cpu line after a while when they bougth them
if it dont work then maybe it's because of 2002 vs. 2003 incompatility

Question to owners of the qtek9100

Hello,
I'm planning to buy a new pocket pc, my choice would be the qtek9100 or the qtek2020i. I've spend a lot of time reading and comparing, and need to know some information from the people who own a qtek9100.
1) Is the qtek9100 able to playback mp3 and run tomtom5 at the same time? I'm asking this because of the omap 850 (ti) cpu and the 64 mb internal memory, I know the omap has a different architecture then the xscale (intel) cpu and can not be compared butt when I use the device in my car I want it to be able to playback mp3 and show navigation at the same time.
3) Is it possible to use skype? Because the minimum requirments of skype is based on 400mhz intel cpu, I don't know how much the omap scores on the intel mhz scale.
2) Is it possible to playback video, without dropping frames?
I have serious doubts about the performace of the 9100 for the things I want to use the device. Any comments from owners would be welcome.
Does anyone know if its possible to put wm5 on qtek2020i? I tought I had read that wm5 is universal and works on any pda, just a matter of drivers.
Greetz
Robin

Skype on Prophet (818 Pro)

Does any try this?
The official Skype said it require min 312MHz CPU to run it.
Just wanna see is the performance on or not.
kowin said:
Does any try this?
The official Skype said it require min 312MHz CPU to run it.
Just wanna see is the performance on or not.
Click to expand...
Click to collapse
I overclocked my Dopod 818 pro to 276 Mhz and Skype works like magic without hassles
Cheers!
don't overclock for too long. The most feasible setting that is observed is 240MHz. Your battery wont die on your all at once and skype (low CPU) will work perfect
Be careful not to fry its motherboard!
Prophet and Skype
The only way to use skype on the prophet is too overclock...I have had success at above 216mhz
Recently I attempted Skype (at 228mhz) on the local GPRS/EGDE network ...I was able to dial/connect and receive the voice from the person I called but they were unable to hear my voice.
Anyone get Skype fully functional on a high speed network?
Prophet and Skype
The only way to use skype on the prophet is too overclock...I have had success at above 216mhz
Recently I attempted Skype (at 228mhz) on the local GPRS/EGDE network ...I was able to dial/connect and receive the voice from the person I called but they were unable to hear my voice.
Anyone get Skype fully functional on a high speed network?
kowin said:
Does any try this?
The official Skype said it require min 312MHz CPU to run it.
Just wanna see is the performance on or not.
Click to expand...
Click to collapse
is ok, I'm using now..I'm not turnup CPU is ok!!
kowin said:
Does any try this?
The official Skype said it require min 312MHz CPU to run it.
Just wanna see is the performance on or not.
Click to expand...
Click to collapse
is ok, I'm using now..I'm not turnup CPU is ok!!
Skype rear speaker / headset
Has anyone figured out how to use skype 2.0 Low CPU with a BT headset, or at least via the regular telephone speaker?
Tom
use Skype Low CPU or HighCPU for Prophet?
hi guys,
WHich Skype version is recommended?
I tried the Low-CPU version since its meant for 312MHz PPC versions
But...I can barely hear the other party. The voice seems badly distorted.
I then switched to the High-CPU version and I can hear the other part lt least.
Anyone had similar experience as above?
Cheers
FY
gunggu said:
kowin said:
Does any try this?
The official Skype said it require min 312MHz CPU to run it.
Just wanna see is the performance on or not.
Click to expand...
Click to collapse
I overclocked my Dopod 818 pro to 276 Mhz and Skype works like magic without hassles
Cheers!
Click to expand...
Click to collapse
This is so amazing....I can only overclock mine to the max of 263MHz anything more it will go bonkers Immediately.
How u manage to push it to 276MHz....any pointers?
Cheers
FY
I was able to get the original Skype that came with my Jamin working. The program is installed on a Sandisk 2gb Ultra SD card and I overclocked the processor to 240mhz.
What is more interesting than Skype is a service called SIPDiscount http://www.sipdiscount.com/en/index.html . Go to that site and sign up for 10 euros, or you can use it free for 1 minute at a time to test it.
You can run the SIP service on a program called SJPhone for PPC http://www.sjlabs.com/sjp.html download the 2003SE version for pocket pc. They work great together and you can even call out to a US land line for free! No overclocking is neccessary because it is much lighter than Skype.
I've attached a text file that explains how to set up SJPhone to work with SIPDiscount. These directions work for the normal PC computer version of SJPhone also.
Have fun :lol:
P.S. You should always use a good headset with microphone for the best sound quality, without a headset there is usually an echo.
on my JAMin with SKYPE 2.00 Higher CPU one, the other person's sound comes out of the SPEAKER PHONE, is that normal or can I somehow switch to regular earpiece
I have a JAMin overclocked to 240, using Skype latest version low cpu, and over Wifi I have a decent, usable sound quality. I haven't tried it over Gprs/Edge.
Re: use Skype Low CPU or HighCPU for Prophet?
I was using Low-CPU (312MHz) version, I can hardly hear other party also. I will try to over-clock and see if it works or not. Or should we use High CPU version? Can anybody provide us the correct version and procedures in a more systematic way?
fychan said:
hi guys,
WHich Skype version is recommended?
I tried the Low-CPU version since its meant for 312MHz PPC versions
But...I can barely hear the other party. The voice seems badly distorted.
I then switched to the High-CPU version and I can hear the other part lt least.
Anyone had similar experience as above?
Cheers
FY
Click to expand...
Click to collapse
I don't overclock my S200, but it's running Skype perfectly. I've downloaded the latest 2.0.0.51 Skype version, installed and started without any problem. I made a voice chat with my friend via Wi-Fi network, he heard me and I heard him clearly.
It's just for people who want to buy Prophet but afraid about Skype not working.
Well, in my Qtek S200 i make a shortcut to overclock the cpu to 240Mhz and run Skype. When i exit skype the cpu clock becames 180Mhz.
I tested in a wifi connection without any problems. With GPRS i haven´t testet yet, but i think GPRS doesn´t have enough upstream to make Skype work properly.
This is my 50 cents!
Regards
GPRS no, Wifi yes
For the people trying Skype over GPRS, read the FAQ before blaming the OMAP processor.
http://support.skype.com/index.php?...base&_j=subcat&_i=12'>Skype+for+Pocket+PC</a>
"Skype for Pocket PC is designed to be used with a WiFi connection. If you are using Skype for Pocket PC with GPRS, you can use instant messaging but the bandwidth does not support calling functionality."
I have no problems with Skype low_cpu over Wifi.
Matterhorn said:
What is more interesting than Skype is a service called SIPDiscount http://www.sipdiscount.com/en/index.html . Go to that site and sign up for 10 euros, or you can use it free for 1 minute at a time to test it.
You can run the SIP service on a program called SJPhone for PPC http://www.sjlabs.com/sjp.html download the 2003SE version for pocket pc. They work great together and you can even call out to a US land line for free! No overclocking is neccessary because it is much lighter than Skype.
I am trying this on a Charmer (MDA Compact II) on T Mobile UK I Have followed all the instructions and it says "No active network interface"
Please Help
Click to expand...
Click to collapse
Skype for ARM
Hi Guys
Well, first of all, I don't have the S200 yet, I'll get it today or on tuesday. I did some research before ordering it:
When it comes to Skype, there seems to be a lot confusion about how to run it smoothly. The problem seems to be, that Skype is compiled to run on an Intel Xscale processor. Well, as we all know, the S200 has an TI OMAP processor and that one has an ARM architecture. Search on Google a little bit, and you'll find out the differences. A TI OMAP 200MHz Processor is comparable to an Xscale 400-450MHz Processor only that the OMAP uses less power.
Naturally, ARM has a lower CPU frequency, but the benefit of it is, that it is multitasking. Xscale is a straight-forward processor, ARM does many things in parallel. This difference in architecture causes problems if one runs an Xscale Program on an ARM processor, because the program does not delegate the different tasks to the different units on the ARM, but only forwards them to the main ALU. That one, of course is overwhelmed, while the rest of the Processor doesn't know what to do.
Conclusion: Skype is for Xscale --> does not use the OMAP all the way and with all the available features (Sound ALU, WIFI ALU, ...)
What we need is a Skype that is made for the processor architecture of the S200
Search on Google and you'll find the following:
Skype for ARM
Of course it is an old version, I don't exactly know what has changed with skype, but as far as I know the protocol is still the same, so calling should not be a problem.
Anyways, I think I'll try the new Skype version first, and then the old one and will compare it.
You'll hear back from me, of cours I'll be happy if somebody else could try it as well and tell us what he or she experienced

HTC TyTn 400 MHz?

My HTC TyTn (not 8525 version) shows when I run battery status program that it's running at 300 Mhz? I know the Hermes200 is 400 Mhz though. What gives?
In windows system info it shows as the samsung processor. Is battery status program just wrong?
soundbyte said:
My HTC TyTn (not 8525 version) shows when I run battery status program that it's running at 300 Mhz? I know the Hermes200 is 400 Mhz though. What gives?
In windows system info it shows as the samsung processor. Is battery status program just wrong?
Click to expand...
Click to collapse
It may be that particular program doesn't have a profile for the newer Samsung processors, so it's interpreting it as a PXA270 at 300Mhz. Check that you have power saving off in settings (and yes, I'm aware that the Samsung chip is not meant to be under or over clocked, but it's possible that some setting is being picked up by the program and giving you the false result)
Other than that, it's possible (but very unlikely) that you have a 300 Mhz preproduction version of the Hermes. I say unlikely because that particular version of the Hermes had only two buttons surrounding the d-pad and used a form factor similar to the Herm100 design.
Is there another program I could use to bench the CPU then? I will have to check those settings. My other friend who has the same phone and is using the same software shows at 400 mhz though so I am not sure.

Categories

Resources