In serious trouble... Device Lock will not go away - 8125, K-JAM, P4300, MDA Vario General

Hi,
I used Matts Device Lock from another thread (http://forum.xda-developers.com/viewtopic.php?t=45953) and now my Wizard won´t unlock!! Soft reset, HW reset, nothing helps. When I press the Unlock Soft button I get a blank screen - nothing else.
Any suggestions?
As of now I can´t use the device at all...
- Glen

I can still access the device via Active Sync (I can see the device in explorer) so any suggestions on how to remove the device lock program from there would be appriciated.
- Glen

pass...
worst case scenario cant you just grab all your important data through active sync and flash the phone with the same ROM - in affect reseting the whole thing? :roll:

Related

White Screen only

I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!
If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.
How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.
press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual
Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already
try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.
Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.
raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?

Password Lock Solution Wm6

As far as we noticed, Wm6 has a terrible bug. Locked device with a password wont be recognized if battery was removed. Also it resets the clock. I believe there is a solution for the password thing. here's what i've done
1- Download and install this cab file Omega-Pass : http://www.megaupload.com/?d=OTW2NZT6 ( A password application that is gonna be used )
2- Go to the application and set the Password- Now the builtin lock application will take the settings from Omega-Pass .
3- youll notice that Windows Lock will require a password as if set as alphanumeric
4- Go back to the Built-in Lock Application and reset the password u want if u need a numerical form Only.
I think also u can just install the application and go directly to the builtin lock application and configure it but didnt try that. Dont wanna risk it i already had 4 hard reset
Now if you do all 4 steps even if u remove the battery for an hours , it will keep recognizing your password. The clock will be reset only. That worked for me .
Please inform me if it works for you also.
Karim.
120 views and no reply ?
well it may work but i just dont use password lock so ... it is useless to me, but this software does not fix the bug only prevents it from happening
Yes of course it interacts with the Builtin Lock code. if we can know how it's preventing it from happening maybe we can fix it ?
i am not so sure where exactly the bug is, but backup battery is only enabled when the main battery is depleted... but when you remove the main battery the power needed for preserving the basic information like time, date, lock password is not transferred from backup battery maybe this is power management or driver bug, and i have seen this in WM5 too
Buth at this time this problem is not yet solved
The thing i dnt understand is that WM6 devices Dont have a Backup battery as i saw on a HTC Touch device. So is it that BA is not 100% compatible with Wm6 ? or it's just a bug with all wm6 devices ?
well I tried, it seem working. for my case, I didn't need to remove the battery to have the problem, after a simple soft reset (after a reconfiguration with the advance reconfiguration tool), the password was lost.
So I do not know if i will have the problem again .
hope not
how did you get in your BA once the password is lost?
i just got my BA and installed WM6...
im down at my 20mins per retry...
Once the password is forgotten , You gotta hard-reset it. This solution only prevent it from being forgotten and cannot restore it.
What is original pass for that device?
Solution
Hi Guys..
The only way to skip this password screen taht i found was it:
Do a HARD hard reset (All data will be lost).
just soft reset first your device, than after you see the stripped screen, press the record and camera button quickly before the the version appears (radio,etc).. then you will see the three options..
enable kitl should be no
clean registry hive should be yes
format storage should be yes
to choose just use the camera and record to change the options...
No more..
I hope that it help.
Help!!!
vipperdiver said:
Hi Guys..
The only way to skip this password screen taht i found was it:
Do a HARD hard reset (All data will be lost).
just soft reset first your device, than after you see the stripped screen, press the record and camera button quickly before the the version appears (radio,etc).. then you will see the three options..
enable kitl should be no
clean registry hive should be yes
format storage should be yes
to choose just use the camera and record to change the options...
No more..
I hope that it help.
Click to expand...
Click to collapse
I got a unit from my girlfriend...in the process of soft spl upgrade something went wrong. Now I have a device asking for a password to unlock it. The old password was "prettyphone" and this password does not work now.
Now I cannot get the unit to connect via activesynch because it is asking for a password.
I press reset and do the above but all I got is a screen normally u see when you do rom upgrade...Please give me advise how to hard reset.
thanks
can anyone upload in rapidshare?
HaiLe512 said:
I got a unit from my girlfriend...in the process of soft spl upgrade something went wrong. Now I have a device asking for a password to unlock it. The old password was "prettyphone" and this password does not work now.
Now I cannot get the unit to connect via activesynch because it is asking for a password.
I press reset and do the above but all I got is a screen normally u see when you do rom upgrade...Please give me advise how to hard reset.
thanks
Click to expand...
Click to collapse
Hi Haile...
Did you these steps correct???
After you press the reset button with the stylus, immediately press and hold the record and camera buttons.
It should work.
No more.
wat i did when i experienced the password not accepted thingy was, when i did the hard reset, we needed to follow the "no, yes, yes" sequence. what i did was not choose yes on the option where it asked to reformat rom(i forgot what was written on the display). i think i chose "no,yes,no". after that, everything was still there and the password on startup was gone. hope this helps to some of u guys.
thank a lot
ccrraaapppp
If the device is locked,when the device is locked how can you download and install something...? Please somebody tell this clown that a device locked on password on WM6 ,you cannot access the phone whatsoever at all, WMDC will ask you to "autenticate" on the phone if you want connection...
The guy who gives this solution hasnt got a clue just as much Bill Gates hasnt.
yesss
yes it worked on mine this way as well.
Obviously the correct password wouldnt work...
Id like to see that billionaire giving some appologies for that....
Anyway mind this first;
Press and keep holding Camera and Record buttons .
Press reset in the same time
Keep holding Camera and Record another 2 more seconds .
Using the same two buttons do the No-yes-yes then
Attention ress just "OK" . pressing reset wont work.
IK does unlock .it just did my HTC .

how reset my o2 neo

i forgot my password after upgrade my wm5 to wm6. i tried to to use spl to flash my phone but my pc cant open my device because my device is locked so the activsync cant do anything.
someone can help me plz!!!!!!!!!!!
*edit* i try to hold the camera and com man buttons adn the same time and press reset button. but it doesnt change
Firstly, I can't see how resetting the device will help you with your problem.
Secondly, how far into a reset do you want to go? Do you want to reinstall the OS or something slightly less drastic?
i just want to open my password. then i will upgrade my phone to wm6 with PIN
Did you set a password after flashing WM6? I've heard that if you do so, your device forgets your password after a soft-reset, and nothing will help your problem besides a hard reset.

Locked out of Phone

Hi all,
I recently applied the WM6 upgrade http://forum.xda-developers.com/showthread.php?t=372485 to my PDA.
However, I removed the battery so I could take out the SIM card, and now it won't accept my PIN anymore. It seems like the registry has become corrupt and does not recognise the PIN anymore.
I can't get into the phone, and a hard reset does not work (I know how it's done, unfortunately). I have also let the battery drain completely (including backup), and it does not hard reset the phone.
What can I do? Are there any tools that can wipe the device through USB?
Thanks!
Problem Solved: Flashed device with provider's original ROM upgrade.. I see this is an issue with WM6
have you perform the hard resett this way ?
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
Cool, thanks for that. Should help for the next time
Have to disable this Corporate PIN policy now..

Screwed my elf! Please help!

Hi guys.
I recently installed Onyx Micro on my Elf, and it's been great. I needed a "Home" panel though, so I installed a Home application that I had on my memory card, and after that reset, my phone's been unusable. When i turn it on, it either hangs, or gives me an error that says something to the effect of "phonesyslog has malfunctioned", and then freezes.
I can't get it connected with Actiesync, I can't hard-reset it either. Any idea what I can do?
Can anyone help me?
Hi,
Did you try removing the memory card? In case that doesn't help, try pressing the camera button while starting up, this should enter the bootloader mode, which enables you to flash a new rom. Do this in Windows XP, as Vista can cause problems. If you've never flashed a rom, try searching this forum for an appropriate rom and a how-to-guide.
Regards,
murosama
Hard reset should work and should be all you need to solve your problem. Make sure that you are performing the hard reset correctly.
For a hard-reset without access to the systems menu do the following:
Make sure the device is switched off, then press both the green and the red phone button and while keeping them pressed switch on the device.
A menu should appear, asking you to confirm the hard-reset.
(Upon confirmation, all data will be erased and the out-of-box state will be restored.)
In case that doesn't work, try flashing a rom that is native to your device
(as suggested above).
Good luck,
murosama
I got the same problem i tryed all off this but didn`t work did you find a sollution for yours?

Categories

Resources