How to use XDA IIi wifi to suft the net? - PDA2, XDA IIi, 2020i Software Upgrading

I'm new in XDA2i here just bought it a few days,now i found out that i can connect with wifi but when i open the ie and key in the url it'll automatic change to GPRS for net browsing.
Is there any setting for wifi that I must set?
have search for a lot of setting in my xdaIIi but still have this same problem.
Need help please.
Best regards.

In network Management
(settings/connections/connections or tap settings on the drop down when hit connection icon, then advanced at the bottom and select networks)
In here ensure both boxes has My Work Network selected.
worked for me,
it will need the top one putting back to GPRS when you wish to make a connection through GPRS

How to use WiFi
Make sure u r going through the procedure.
1. Your WiFi capable device must be in the range of a Wireless Router (internet connected).
2. I assume that ur Wireless Router is set on security (allready set to allow specific users).
3. Every WiFi device has got an unique ID called MAC address, so your phone has also got a MAC address e.g: 00:09:2D:1F:34:E3. U have to go into the Wireless Router settings to enable ur WiFi phone.
4. Go into your Wireless Router settings (u need router's login ID & password to login) and add a device, give it ur phone's MAC address (Point 5) and a name (e.g. My XDA), Apply->Save->Logout. If ur Wireless router is security enabled then there must be a password called "WEP Key" e.g. "AE4ED24C54", now write it down to put it in your Phone to login to the Wireless Router to use the WiFi internet.
5. Find your phone's MAC address at: "Start->Settings->Connections(tab)->WLAN->(in the status: Not connected to network) click the bottom left Green button->click WLAN button(it will turn green from red)->ok->in the MAC: would be ur device MAC address(e.g: 00:09:2D:1F:34:E3). (write down on a piece of paper for the router settings).
6. As your phone is already "WiFi switched on" in point 5, it should detect ur Wireless Router once u finish point 4.
7. Phone will detect & show the name of ur Wireless Router, select it, it will ask for the Password now (WEP Key), enter the Wep Key and here u go.
8. Now ur Today screen Top "G" icon should change (antenna type icon) and show ur decice as connected in few seconds, u can switch it off by clicking that icon and click "Turn OFF WiFi" on the popup, you can switch it back on by: Start->Program->Wireless Manager->WiFi icon.
This explaination is only for WiFi enabled devices.
Tell me via email if u got stuck somewhere.
:idea: GoodLuck :idea:
Sidd

Related

WiFi Connecttion

Hi Everybody!
I'm looking for some help with connecting to my home WiFi.
In settings, netwok card, I can see my home network.
I use a netgear router with WEP security.
I just can't seem to connect and I can't seem how to input my WEP acces passkey too?
Thanks for any replies
{>
In settings, wireless lan, advanced it states that I am connected to the network, but I still can't connect when using IE?
the message reads : " U~nable to obtain a server assigned IP address . . . etc"
Do you have DHCP enabled on the wireless router? Have you used the wireless network with another device?
Mmm, very good question!
The answer is "don't know". Will check and let you know Syn.
Will start again.now that I have managed to "flash my rom"
Well this is what I have :
Wireless Network
Name (SSID):
Region: --- Select Region ---AfricaAsiaAustraliaCanadaEuropeFranceIsraelJapanMexicoSouth AmericaUnited States
Channel: 01020304050607080910111213
Wireless Access Point
Enable Wireless Access Point
Allow Broadcast of Name (SSID)
Wireless Card Access List
Security Encryption (WEP)
Authentication Type: AutomaticOpen SystemShared Key
Encryption Strength: Disable64bit128bit
I have added the device to my wireless network list with the MAC address
Signal is VERY GOOD!!!
Am I missing out son some settings?
{>
I've tried to set up a new connection as Internet Explorer tells me it cannot connect with the current settings?
What settings do I need?
I have entered the WEP key, and I don't use passwords on my wifi system??
{<
Do I need an IP address?
Scutter
First things first, forget the PDA for few moments and lets establish what is going on with your AP. The question that [sYn] has asked is very important - do you have DHCP enabled on the AP. The answer you posted is meaningless as it only shows the options and not the current config. Interrogate the AP and look for where the LAN side DCHP option is and make sure it is set to ENABLE or ON or whatever positive indication is used.
Once you are sure this is configured (ideally tested with a PC) then go get your PDA and try connecting again. If it still doesn't work disable all the security and encryption settings and turn off that stupid MAC address authentication which, by the way, is pointless. If needs be do a factory reset on the AP. With no security enabled try conecting the PDA. It more than likely will connect now. Once it does start building up your security one layer at a time making sure you test at each stage. Can I suggest that you forget WAP and MAC authentication and use a WPA Pre-Shared Key instead as this provides bucket loads more security.
Hope this helps.
JT, thanks for all your help!
I use a netgear router. Whilst awaiting a reply here I did a bit of research and took of the security of my router. I then connected my device using a shared key (I have always had this) and then put the security back on.
I had to reconnect my laptop too. I think the reason isthat the router was set for an automatic setting and I chaned this to an open system.
THANKS AGAIN FOR YOUR HELP !!!
{>

USB to wifi dongle

I've got a USB to WiFi dongle , D-LINK DWL-G122 , and I want to use with my PC so i wiil be able to connect my JASJAM anywhere in my home. I've intall it on my PC with no problems. Do someone know how to config the PC ? Do I need to config anything on the JASJAM ? I have no router involves .
You need to configure ad-hoc connection
Ad Hock is done , but still no connection
I'v done so but i'm getting No connection at Wireless Network Connection 3.
Also Windows Small Office Network Wizad mention that . Any ideas how to make my D-LINK DWL-G122 connect ?
Since you've got no router in your set up, you need to set your phone's wireless network connection to only use ad-hoc connections too - go to Start | Settings | Connections tab | Wi-Fi. On that screen, change the "Networks to Access" option to "All available" or "Only computer to computer".
Then you'll need to give your phone a fixed IP address in the same range as your PC; tap the Network Adapters tab, then tap the adapter that is highlighted (it will mention 802.11 and Wi-Fi in the name somewhere!). Tap on the "Use specific IP address" and then enter one in the box below - if your PC is using e.g. 192.168.0.2, then set your phone to 192.168.0.22, set the subnet mask to 255.255.0.0 and the default gateway to your PC's IP address (you can find your PC's IP address by opening a command prompt and type "ipconfig" - in case you didn't know!).
That should get you most of the way there....can't think of anything else myself, but I'll post again if anything else springs to mind
Mark.
OK - it is working now
Thnx for your help

Network Key Required

I have a wireless network at home that is secured by WPA-PSK. When I access the wireless network on my phone it says a network key is required and I enter it. The wi-fi will work for a few minutes and then it will ask me to enter the network key again. Does anyone know how to store the password so I don't have to enter it every time I use my wi-fi at home, or a way to stop it from continually asking me for the password?
This is a strange behavior. Normally the password is saved automatically, in fact once a network is detected all its settings are automatically saved and there is no manual option to do it.
Unfortunately I never heard of such problem before so I have no idea what could be causing it.
Hi,
Very strange behaviour indeed! Anyway, let's see what we can do for you here.
It appears that you have not configured the network key on your network. If you had, this would have permanently stored it for you and not keep asking you for the key as though you were trying to piggy-back on someone's network.
Now, you wouldn't do that, would ya? War driving is against the law over here in the UK.
Here's what to do:
1. Enable WiFi
2. Start->Settings->Connections->WiFi
3. Click on your own specific network
4. Click - Next
5. 'Configure Network Authentication' screen appears
6.
Authentication: WPA-PSK
Data Encryption: AES
The key is automatically provided: blank (i.e. unticked).
Network key : xxxxxxxxxxxxxx (you MUST enter it here by yourself)
Key index: blank (i.e. unticked)
7. Click Next
Use IEEE 802.1x network access control: ticked (automatically, by the system)
8. Click Finish.
9. Soft reset your device for the settings to take effect.
.......and voila! no more network key questions.
Hope this helps.
kiwi992.
Well that didn't work...it's still doing the same thing
Hi,
Hmm........ What next? I ask.
This time, we'd have to concentrate on your router settings. This seems to be the culprit since everything in the device is configured exactly as we discussed in the last posting.
Did you use Windows to configure your wireless connection settings for you or did you configure it manually, using the CD that came with your router? I did the latter for better control.
If you used Windows, then navigate to: Start->Control Panel->Network and Internet Connections->Setup or change your Internet connection.
If you used the CD that came with your router to configure it, then look towards the bottom right of your PC or laptop and you will see a dark green icon which says (e.g.) 'Netgear WN511B is connected to........' Click on it to ensure that the security is set to WPA2-PSK[AES] and that the network key is entered manually.
Either way, please:
1. Check your router settings to ensure that it has not been set to prompt for network key.
2 Ensure that the network key is NOT automatically supplied by the gateway. If the radio button is ticked in your configuration, un-tick it.
3. Check your Windows Network and Internet Connections settings if you've used windows to configure it.
I am using the same security as well as encryption and I don't have such problem.
Hope this helps.
kiwi992.
throwing in my two cents...
kiwi992 said:
Hi,
Hmm........ What next? I ask.
This time, we'd have to concentrate on your router settings. This seems to be the culprit since everything in the device is configured exactly as we discussed in the last posting.
Did you use Windows to configure your wireless connection settings for you or did you configure it manually, using the CD that came with your router? I did the latter for better control.
If you used Windows, then navigate to: Start->Control Panel->Network and Internet Connections->Setup or change your Internet connection.
If you used the CD that came with your router to configure it, then look towards the bottom right of your PC or laptop and you will see a dark green icon which says (e.g.) 'Netgear WN511B is connected to........' Click on it to ensure that the security is set to WPA2-PSK[AES] and that the network key is entered manually.
Either way, please:
1. Check your router settings to ensure that it has not been set to prompt for network key.
2 Ensure that the network key is NOT automatically supplied by the gateway. If the radio button is ticked in your configuration, un-tick it.
3. Check your Windows Network and Internet Connections settings if you've used windows to configure it.
I am using the same security as well as encryption and I don't have such problem.
Hope this helps.
kiwi992.
Click to expand...
Click to collapse
Hi Kiwi392 and CapitanOats25:
I've been working to resolve a similar problem with WEP, and learned something I thought might help in this case: On my router, a NetGear WGR 614 v.6, when I enable WAP PSK I get an entry field labeled "Key Lifetime." By default mine is set for 60 minutes, but you can set it for longer. Perhaps that is the problem?
I hope that helps.

Elfin can't connect to belkin N router

Hello... Got a Touch recently, and doing research found this forum. One of the best findings lately for me: already flashed the phone with a WM6.1 ROM and updated my radio successfully. But I have a problem (even before the flashing):
I can't connect to my wifi. I have a belkin N router. Have tested almost everything: updated the router's ROM, updated the phone's radio, turned off security, assigned manual IP's, etc, but with no success... so I'm running out of ideas. I can connect to another people's wifi's tho.
Anything I have missed? Just an incompatibility? (which means I'm screwed)
Thanks a lot
is t on n only mode?
touch is g/b as u probably know
if not, try with no security to see if it connects
Yeah, it is in a multiband setup (g/b/n).
Also tested with no security. No sucess.
I have the same problem, I'll let you know if I find a solution.
Same thing... I'm trying to figure out a solution, any findings, will post here.
I tried to connect my Touch to my old netgear 802.11b router at home without any success. I did a lot of "googling" on the subject, and only found that many concluded that it wasn't possible to do so.
Also, I have AT&T, and they are offering free hotspot WIFI connectivity to their customers (which is intended for laptops). My touch detects the WIFI signals, but I have yet to find out how to make a connection.
It seems like there should be a way to do it somehow though!
Anyway...
Best Regards!
pl, when you go into your Settings -> Connections -> Wi-Fi, can you see your wireless network being detected?
The only things that spring to mind at the moment, are the basics for normal connection ...
1. Network type (B/G/N)
2. Authentication (password)
3. MAC Filtering
Here's what I would do ...
1. Reset router (usually has default button at the back).
2. Set it up for DHCP (sometimes cures a lot of problems).
3. Set simple WEP with password.
4. Obviously a network name (make sure it is not hidden, also make sure AP is enabled)
5. Set channel
6. Set mode (Network type) to mixed.
7. Save and reboot.
8. Soft reset Touch
9. Go to Settings -> Connections -> Wireless LAN
10. Activate Wireless and see if your SSID (network name) pops up. From here you can see signal quality and IP (to make sure you got it from DHCP).
Give it a shot and let us know what happens.
same problem here, really annoying!
Strange, I have never had problems with mine (had it connected to a couple AP's already). In fact, it's easier than connecting my laptop to a WLAN.
You have anything else that can connect to your Router? pc or something.
My Touch can connect to other routers, and I have 2 PCs at home which connect to my Belkin N router, I just can't connect my Touch to it.
I found a solution
Customer Call Details Nov 13 2008 04:37
I have an HTC Touch that can connect to other hotspots, but not to my home Belkin router. Sometimes, if there is another connection available, it can see the router, and says that it is Available, but cannot connect; other times it won't even see it. I have checked for firmware updates, but I have the latest. Any help would be greatly appreciated.
Belkin Response Nov 14 2008 22:18
Hi Lilburd,
Thank you for contacting Belkin Technical Support.
We understand that the HTC Touch does not connect to the router. We apologize for the inconvenience caused.
Please follow the steps given below to update the firmware and configure the router:
We recommend that you update the firmware from a computer that is connected to the router with an ethernet cable.
Please download the latest firmware on the router from the link given below. Download the file "3.01.29":
http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=10288&scid=0
and save it to the computer.
- To update the firmware, log on to the router`s web interface by typing in http://192.168.2.1 in the address bar of the browser. The computer should be
connected to the router with an ethernet cable.
Note: If you have changed your Router’s IP address, use that IP address.
- By default, the password is blank. Click the "Submit" button.
- Click on "Firmware Upgrade" under the option "Utilities".
- Click on “Browse” and select the bin file that you have downloaded.
- Click on “update” and follow the wizard.
- After updating the firmware, restore the router to factory defaults by clicking on "Restore Factory Defaults" under "Utilities".
- Reconfigure the router.
Please follow the steps given below for configuring the router:
- Connect the computer to the "LAN" port on the router and connect the modem to the Internet/"WAN" port, using Ethernet cables.
- Take a paper clip, insert the paper clip in the reset hole of the router and hold it for 15 seconds.
- The power light will flash and then come back "ON" solid, indicating that the router is being restored to factory defaults.
- The corresponding lights on the front of the router should be lit up.
- On the computer, check if you have an IP address in the range of 192.168.2.x.
- If not, specify a static IP address, gateway and "DNS" address by following the steps given in the link-
http://web.belkin.com/support/kb/kb.asp?a=2824
- Log on to the router web interface by typing in http://192.168.2.1, in the address bar of your browser.
- By default, the password is blank.
- Click on "Connection Type" in the left hand column under "Internet WAN" heading.
If the connection type is Dynamic (cable):
- Choose "Dynamic" and then click on "Next".
- Type in your “Host Name”, if your Internet Service Provider has provided it. Else, leave it blank.
- Click on "Change WAN MAC Address".
- Click on the button "Clone".
- Click on "Apply Changes".
If the connection type is PPPOE (DSL):
- Choose "PPPOE" and click on "Next".
- Enter the user name and password given by your Internet Service Provider.
- Save the settings.
- Click on the "Home" link at the top of the screen.
Internet Status should show "Connected" on the top right hand corner of the web page.
If the problem persists, please get back to us with the following information:
1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or static).
2. Name of the Internet service provider (ISP).
3. Version number of the router. You would find the version number on the bottom of the device. It would be a number in a series of thousands with a prefix “ver.”.
4. If the internet connection is stable on the computers using the router?
5. If the HTC Touch detects and connects to other networks in the neighborhood?
Lilburd, if you need further assistance please feel free to write back to us and we will be happy to assist you.
Regards,
Belkin Technical Support.
That really is strange. The way I see it, WLAN is a standard. It's like BT, any headset should work with any BT phone, as would any wireless device work with any wireless device
Maybe force the router to only broadcast in G (or even B) and see what happens? (I know, I'm reaching now )
Tried everything so far, no success. Even with no security enabled.
same problem here, Very Annoying, tried every thing
HTC Diamond doesnt connect to WiFi!!!!!
EMoeHTC said:
I tried to connect my Touch to my old netgear 802.11b router at home without any success. I did a lot of "googling" on the subject, and only found that many concluded that it wasn't possible to do so.
Also, I have AT&T, and they are offering free hotspot WIFI connectivity to their customers (which is intended for laptops). My touch detects the WIFI signals, but I have yet to find out how to make a connection.
It seems like there should be a way to do it somehow though!
Anyway...
Best Regards!
Click to expand...
Click to collapse
ANY SOLUTIONS TO THIS ISSUE YET....WAITING TO USE WiFi on My HTC-D.
THanks
Same problem here, N1 Vision router and XDA Orbit, both running on latest firmware. Wrote to Belkin support describing the issue. Here's their reply:
Code:
Thank you for contacting Belkin Technical Support.
We understand that you are not able to connect XDA Orbit WM6 communicator wirelessly.
To resolve this issue we suggest you to open ports on router.
Please collect the port number from the XDA Orbit WM6 communicator vendor and enter under "Inbound port" & "private port".
-Please open the Internet Explorer and in the address bar type in "192.168.2.1" and Enter.
-Leave the password blank and click on "submit".
-Click on "Virtual server" under the "Firewall".
-Enter the port number under "Inbound port" & "private port".
-Enter the IP address of this computer under the "Private IP address".
-Check the "Enable" box and click on "Apply changes".
George, if you need further assistance please feel free to write to us or call us on 08456077787.
You can also contact us through our online chat support at:
http://www.belkin.com/chat/technicalsupport.aspx
Regards,
Suzane Taylor
Belkin Technical Support
Utter nonsense...
I just got my Touch Diamond from Sprint and am having the same issue. I have a Belkin N+ Router that is in g/b/n wireless setting.
The phone just simply will not see the SSID even if you put the settings in there manually. What it does see however is the guest SSID my router emits and connected to it without any issues. The guest account is a feature of my router gives friends access to the web but denies access to internal network.
Out of curiosity changed my routers wireless bands to only G/B and all of a sudden my phone can see the network. Unfortunately for me I rely on the N part of my network to connect my laptops and do streaming HD so leaving it on G/B is not acceptable.
I just connect via the guest account, anyways its not like my phone would have been able to see the internal home network anyways.
Just my 2cents
I have the same issue.
Used to use a D_Link G router, but recently upgraded to a belkin N-draft one.
My laptop connects on G, and my desktop on N, so I can't switch N off and just use G.
Anyone found a solution yet? It's bugging the hell out of me!
I posted a fix on page one that should work. You have to update your firmware.
Did u all using any encryption security?
128bit WEP - touch have a problem of connection
64 bit WEP - works
have you enabled easypairing, (WiFi easypairing : Enabled) if so turn it off or press the required button sequence on the router to connect.

set up static ip

hello help,
my wife has an htc hd2 phone and i am trying to connect it to our home network. we have an mn700 microsoft router. i have security on it WEP
and on channel 3. The phone is asking for a network key and i put in the wep key and and put it on channel 3 it
states that iam connected but we still can not surf the web.
all other wireless computers and laptops in the house i have assigned a
static ip, i oculd give her phone a static ip but i can not find where or how to do this on htc hd2 phone.
i am thinking that this is the solution, if not please point in the right direction.
also ineed step by step directions on the phone since it is not mine i do not know to much about it.
thanks,
craig
I'm right there with ya, exact same problem. It's amazing to me that a device as sophisticated as this is so difficult to set up. Here are my posts from the t-mobile forum..PLEASE HELP...
I just got my htc hd2. So far I love it. my last phone was a G1 and it was able to automatically switch to my home wireless network when I got in range. Is this possible on the hd2? Also Is it possible to set a static IP address for these devices? I have not been able to get it to work on my LAN. If anyone can give me a walkthrough to set the phone up so It automatically switches to my LAN with a static IP when I'm in range this phone will be pefect...wife just got the cliq xt and she's teasing me... TIA
can anyone tell me how to set a static IP address and how to get it to connect over my LAN. I called customer care and the person i spoke to only had a set of written guide lines and couldn't tell me how to do it, said he had never been asked before. So, Here's what I've done so far to get this device to work with my wireless at home. 1st, Click START > SETTINGS> Wireless Controls and turn Wi-Fi on. It sees my Wireless network and the icon spins to let me know it's attempting to connect? I've put my network password in before so eventually I get a green check mark. So next I tap Advanced in the lower right corner and get to the Wireless Lan page. Then I tap the Change Network button which again lists my wireless networks in range and mine is listed as connected. so then I click the Network Adapters Tab, which brings me to my first question. What should be the setting for "My network card connects to:" I assume "The Internet" but I could be wrong. Below is a long list of adapters I can modify, which brings me to my next question which adapter do I modify? I assume the Broadcom 802.11 Network Adapter, when I tap it I get a screen where I can set a static IP and DNS. I figured I had it at that point, except It doesn't seem to work!. The wi-fi antenna icon is at the top and I have two arrows next to it pointing left and right. green check on my wi-fi network, but when I try to use Opera browser it says ERROR! Connection closed by remote server and I cannot ping the ip i set in the device from my network. I go back turn Wi-Fi off and everything works again. AM I DOING ANY OF THIS RIGHT? thanks again.
Okay, got it to the point to where I can ping the device on my network. The adapter I had to set the static ip to was the Broadcom 802.11 DHD Network Adapter. Using Wi-Fi toggle to turn it on and off and it responds well and connects reliably. However, when I try to browse it fires up the 3G connection. I have just now been able to use remote desktop on my local network using the servers IP, without it turning on the 3g connection. Looks great in 16bit color, but no landscape mode? Most other apps, facebook the browser and others make the 3g connection come back on. How can I make all data connections go over my lan? almost there....
I got it to work, not sure if this is best practice or not, and it's definitely not elegant, but it works.
1. Touch Start > Settings > Wireless Controls and Turn wi-fi on
2. Select your wireless network and enter your password or key
3. Once you are connected (green check), touch Advanced > Change Network (under the ssid) you will see your wireless connection again and it should say connected
4. touch the wireless adapters tab at the bottom. Here at the top select my network card connects to The Internet and select your wireless adapter from the list below.
5. set your static IP address and Name Server info. Touch OK and then return to the home screen
At this point you should have the wi-fi icon with two solid arrows next to your 3g icon.
6. Touch Start > Settings > menu > all settings > connections > connections > advanced tab > Select Networks.
7, change both drop downs to my isp (may be different if you named it something different)
to get back to 3g repeat steps 6 and 7 to switch both dropdowns back to tmobile data or whatever yours was originally and turn off the wi-fi (or download wi-fi toggle) and turn wi-fi off. 3g should come back on automatically if you run an app that connects to the web. if not turn data connection back on in the comm manager.
This works but this sucks. Is there an easier way to Automatically switch between 3g and wi-fi? Am I making a simple problem over complicated? or is there and app for this? Android beats winmo 6.5 on this one.
still no wifi
hello,
trying for days, i can not get your setup to work. still connected
but no internet browsing. i took the same ip that i am using for the phone and put it on the laptop---so i know it is the phone and not anything going on
with the router.
craig
To the OP, i am by no means an expert on this topic. This is how i got mine to work. only advice i could give is to make sure you are editing the correct adapter and if you named your connection settings something different double check. How far do u get with the instructions? do you get a green check after you put in your network key?
I can switch back and forth between wi-fi and 3g no problem but it would be nice to have it done automatically when i'm in range...can anyone help
finally
we reset the phone and then followed your directions. Viola! it worked!
we are working on how to setup identies for different networks,
thanks again mr1credible.
Update. My phone locked up hard and kept telling me my password was incorrect so I had to do a hard reset...After the reset, I decided to take another look at the Network settings..I've got it set up now so that All I have to do is turn wi-fi on and it will use my wi-fi as the preferred connection. All I did was follow steps 1-6 as previous except when I got to step 7, I only changed the second drop down to My ISP. Both Icons 3G and Wi-Fi appear at the top but I can remote desktop my PC and connect to my shares on my local network. I also have it set to automatically shut off my wi-fi if it cannot connect in 30 sec, So when I leave for work in the morning I don't have to remember to shut it off, and I don't have to switch back and forth between settings anymore. All i have to do is turn wi-fi on when I get home. Not bad. Still would like to have it automatically detect my network and connect when in range but I can live with this....
Try SolarWinds Orion IP Address manager.
It Manage your entire IP infrastructure from an intuitive web console .
Also it Prevent your subnets and DHCP scopes from filling up with preventative alert notifications .
check it at
SolarWinds website.

Categories

Resources