How to hard reset MDA T-Mobile PINK.
Br.
A. Wahab
!! VERY IMPORTANT !!
try SEARCHING or RTFM.
regards.
Oh yes everyone, let's drop everything else and get to this right away ;-)
You can find ik here:
http://forum.xda-developers.com/search.php
I tried all over.. but don't found..
Its not a Magician..
its a wizard... and I tried but not found..
Anyone here please waste his 2mins to help me out.
Br.
A. Wahab
if you have same one as on the picture then its Magician..
Its not a Magician..,
Its don't have Intel processor.
waiting for reply from an expert.
Br.
A. Wahab
From the BACK Side its type is
PM200
Br.,
It's a bit complicated with the wizard version of the magician you've got...
First you need two STRONG magnets, a 220 volt wallsocket and some electrical wire.
Now you strip the wire and put the bare copper wire in your mini sd slot
place 1 of the magnets on the table, lay your wizician on it and the second magnet on top. (like a sandwich)
Then plug the electrical wire in your wallsocket and... BAM!! it will be hard reset.
OR
you could do a proper search on the forum
leploep said:
you could do a proper search on the forum
Click to expand...
Click to collapse
If u have skills to search proper. search and tell me link...
I am sure its is not a magician,
because hardware is diffrent..
Its have same hardware as
Qtek S110
I-mate JAM Black
waiting for reply from a person who have enough knowledge..
Br.
It is not a phone which can HARD RESET by pressing POWER + RESET
its have diffrent method to hard reset.. any one knoww????
hold down record and camera and tap reset at the bottom. keep holding record and camera until screen prompts you to push send (green phone) to reset.
The phone isnt magician or wizard, its a charmer. Jam black and S110 are both magicians.
leploep said:
It's a bit complicated with the wizard version of the magician you've got...
First you need two STRONG magnets, a 220 volt wallsocket and some electrical wire.
Now you strip the wire and put the bare copper wire in your mini sd slot
place 1 of the magnets on the table, lay your wizician on it and the second magnet on top. (like a sandwich)
Then plug the electrical wire in your wallsocket and... BAM!! it will be hard reset.
OR
you could do a proper search on the forum
Click to expand...
Click to collapse
I think it would be better if this was done while in a bathtub instead of on the table.
Kidding aside, as Dr. Mobile said in his first post : QTEK S110,
MDA T-Mobile PINK/BLACK, I-mate JAM BLACK.. This is definitely a Magician with the 128MB memory upgrade and WM5, right? I think this is the HTC Charmer?
The Wizard is supposed to be QTEK 9100, MDA Vario, I-Mate K-JAM. This has a slide-out keyboard
Here's the T-Mobile link to the specs corresponding to the picture posted :
http://www.t-mobile.co.uk/Dispatche...nType=pmt&pmid=7242&menuid=ctl_phones_details
Go Figure
dave106 said:
hold down record and camera and tap reset at the bottom. keep holding record and camera until screen prompts you to push send (green phone) to reset.
The phone isnt magician or wizard, its a charmer. Jam black and S110 are both magicians.
Click to expand...
Click to collapse
Spoiler :lol:
dave106 said:
hold down record and camera and tap reset at the bottom. keep holding record and camera until screen prompts you to push send (green phone) to reset.
The phone isnt magician or wizard, its a charmer. Jam black and S110 are both magicians.
Click to expand...
Click to collapse
You are the only Person who have some knowledge.
my problem is solved.
THANKS....
Jorgee said:
Here's the T-Mobile link to the specs corresponding to the picture posted :
http://www.t-mobile.co.uk/Dispatche...nType=pmt&pmid=7242&menuid=ctl_phones_details
Go Figure
Click to expand...
Click to collapse
Now thats really funny
Related
Hi Guys,
I know this might sound crazy but I was wondering if anyone is having this little problem.
Whenever I hold the jam by where the "i-mate" logo is, i hear and feel a slight click, it's as if the jam's case is not sealed correctly. If you don't knwo what i mean, it's like when you put ur thumb on the iMate logo and your pointing finger on the back of the jam and then pinch, you can feel the jam make a very slight click. The other four corners of the jam is fine and tight, but the i-mate logo corner seems to be slightly clicking and not tight whenever u squeeze or pinch it.
IS THIS JUST ME ?????????? if it is i should probably return it for another! PLEASE LET ME KNOW GUYS HELP!!!!! THANKS!!
no i dont think so :wink:
if u meant the cover then i have a little bit of click at i-mate logo
NightmarE said:
no i dont think so :wink:
if u meant the cover then i have a little bit of click at i-mate logo
Click to expand...
Click to collapse
YEA !!!! THAT's EXACTLY what i mean!!! at the i-mate logo, you have a bit of a click too right??????????? SO THIS IS ON ALL JAMS???
i think all i-mate jam units have the same problem, plus i looked up into 10units and i found that every unit has a little scratch on the cover in diffrent place ....
i thin the first version has some problem. well, i think the second versin willl has a few problems....
that just totally sucks... I think i will just go and super-glue it tight so it wont click no more
:lol: i'll let you guys know what happens, hahah
no klik for me
hahah are you SURE????? you just messing with us right?
Click
Yep, mine does it too.
On mine, I can see that it is being caused by the fact the case is a little loose at the back (behind the iMate logo!)
P
Just got mine today from Modaco and I'm really chuffed with it. No clicks, No Scratches. Its perfect. Anybody want to be an XDA IIs
No click here
I plan on buying a deskcharger but ofcourse when putting the phone on it will need removing the rubber cap on the bottom of the phone every time. That's a bit of hassle. So, how to remove the cap permanently ? Hopefully it's possible to cut one end of the rubber "string" and pull it through the hole. If not, then it would be best to open the phone I guess. Anyone know the best procedure for this ? Many thanks.
Where is rubber cap? 8)
code72 said:
Where is rubber cap? 8)
Click to expand...
Click to collapse
Where's your head ? As in my original post : " the rubber cap on the bottom of the phone". Anyway I understand this HTC Magician has many different faces and asses My model has the rubber-cap. Any help would be appreciated.
Code72,
The 'rubber cap' is a dust cover for the usb and headphone jack on the Dopod 828, Krome Spy and Orange SPV M500. All the other versions of the Magician don't have it.
Daffie,
I would pull out the rubber cap as far as it can go and cut off the 'strings' as close to the body as possible. that way the ends should just disappear back up into the case.
TheBrit said:
Code72,
The 'rubber cap' is a dust cover for the usb and headphone jack on the Dopod 828, Krome Spy and Orange SPV M500. All the other versions of the Magician don't have it.
Daffie,
I would pull out the rubber cap as far as it can go and cut off the 'strings' as close to the body as possible. that way the ends should just disappear back up into the case.
Click to expand...
Click to collapse
Thanks. Yeah that's what I figured. Hopefully if I cut the string on one side only it can be pulled through the hole. That would be the ultimate solution. If that doesn't work then I'll cut both sides. I'm afraid though the leftover piece of string could get a life of it's own inside the phone
:wink:
Hey, I'll swap you my plain vanilla magician for your m500, I like the rubber cap! My USB port is full of dust and crap!
why dont you disassemble the device and remove it? disassembly guid is available on the ftp server of this site
fone_fanatic said:
why dont you disassemble the device and remove it? disassembly guid is available on the ftp server of this site
Click to expand...
Click to collapse
I have looked but can't find it. Could you point me in the right direction please ? Thanks.
Have a "small" problem with my touchscreen, it requires to be aligned every day,and by that i mean that the alignment doesn't hold much long...that means sms typing is extremely hard when you push one letter he shows you another that lays next to it .Is it due to the touchscreen or the system....i didn't do any ROM update i still have the original software on him:
ROM Ver.: 1.12.01 GER
Radio Ver. : 1.12.00
ExtRom ver. : 1.12.151 GER
Many thanks!!
i think it it the problem of touch screen
i think it it the problem of touch screen.after extrem use of touch screen its loes the alinement for this you replace the touch screen from your hardware guy.
Thanks for all
Hi i fixed the problem with a ROM update and i didn't install extra programs that i had before like ( Pocket plus or Calendar ++...... ), anyway now i don't have to align the screen. I don't know is it the ROM update or the additional software but the touchscreen is now working perfectly.
So if someone else have a similar problem don't replace the screen right away.
Thanks
it's hardware problem.
my xda mini also..
but i know how to fix this problem.
Maybe with you it was, my MDA is now working perfectly and i don't need to align my screen every day as i did before.That doesn't mean that all have such a problem,i am only telling you my experience with it.
Best regards from Vienna
Hello, in my magician is not everyday, hapens all the time that i turn on it.
I had replace it 3 times, but i can find a good dealer of touchs. You knows one that seel a good touch?
regard's,
Ricardo
Guys,
I've had that problem for a LONG time and today i finally got tired and decided to fixed it...here's how i've done it: You just need to lift a little bit up, a few small metal pins which are all around the touchscreen (see the picture in attachment). This will force the touchscreen to remain in place and will end all your problems related to touchscreen alignments.
Regards,
Keeper
so it does help? what do these pins do?
IS THERE REALLY NO SOLUTION TO THAT PROBLEM???
(* the pins have nothing to do with the touchscreen, they are what holds aluminum shell on the plastic chasis)
i had an o2 mini with 1.11 rom and its touch screen was not quite sensitive.. had to tap or drag stylus very hard..
but after upgrading to 2.03TX.. to my surprise.. my PDA now has very good touch screen response!
hi, i have this problem
I tryed to re-flash rom or adjust metal pins but the problem persists.
Anyone have another solution?
Plese help me, i want to save my pupil
i have the same problem. the o2 is really a great little phone but i think im going to be forced to upgrade
i also got a unit mini xda from a friend, he said it is dropped and can't tap screen. i hold and press the screen, then slide up and down, side by side, and now its ok.
Trullalero said:
Anyone have another solution?
Click to expand...
Click to collapse
Probably it's problem with flat wire that connects screen with mainboard.
You need to open yours xda, find that wire, unplug it from mainboard, clean its pins with alcohol and plug into again.
From this time mine xda doesn't decalibrating anymore
khuan said:
i also got a unit mini xda from a friend, he said it is dropped and can't tap screen. i hold and press the screen, then slide up and down, side by side, and now its ok.
Click to expand...
Click to collapse
hi khuan thanks for the great tip.. you save my $$$!
I was just thinking to upgrade my mini since it response too slow when i tap the screen
but now it works just as it is new.
guys.. try khuan tip.. it really works!
khuan said:
i also got a unit mini xda from a friend, he said it is dropped and can't tap screen. i hold and press the screen, then slide up and down, side by side, and now its ok.
Click to expand...
Click to collapse
what exactly do you mean?
can you be more specific ?
Screen Setting
new_ppc_user said:
what exactly do you mean?
can you be more specific ?
Click to expand...
Click to collapse
Hi
My cell also had the same problem. There is a bunch of wires coming from the back of touch screen, these wires fix inside a socket. There is a black color cover that fix the wires inside that socket. During mishandling that cover got loose, that's why your cell loose the screen setting. I fixed that cover and now my Jam works perfectly. (Do it if you have the courage to open your cell)
Ali
Hello, I just bought a used O2 mini and had this same problems. I finally found a quick way to restore the calibration that goes out every restarts.
Using resco registry editor, I found the data stored here->
HKEY_LOCAL_MACHINE/HARDWARE/DEVICEMAP/TOUCH/CalibrationData
So I make 1 clean alignment and quickly went and export the Touch key into my Storage. Now every time the alignment goes haywire, I just import the data back. Hope it helps.
hi!
I've a big problem with the "front button" of my TyTn (the keypad and the upper buttons).
they don't work for 90% of times.
The configuration of these button in WM is correct.
This problem is with WM6 and also WM6.1
What I can do?
thanks
same here
it's really annoying...
anyone solved this problem?
same here
It would help if you could be more precise about which buttons are not working (the Hermes doesn't have a 'keypad' per se) which variant of the Hermes you have (8525 etc) and which ROM you have.
OK!
the model is hermes200 with WM 6.1
udk 8.0 R2 vega - kaiser ROM 3.62
CE 5.2.19209
Build 19213.0.7.0
I hope the informations are what you need.
I attach a picture with the buttons that don't work
Just got my phone back from the service (because of that problem) My friend who repaired it told me that the cable that connects the screen with the main part of the phone did everything.... ( sorry for my english)
juvenilebg said:
Just got my phone back from the service (because of that problem) My friend who repaired it told me that the cable that connects the screen with the main part of the phone did everything.... ( sorry for my english)
Click to expand...
Click to collapse
Yes, and that flex cable connector is a good place to start for the DIY people here.
Mike
I opened my Tytn several times and cleaned the inside stuff, reconnected connectors.
Now it's ALMOST good. Still few times a day front buttons die, but emmediately after turning display ON and OFF buttons start working.
I did it reading this site.
What about flex cable connector? Isn't it fixed with a tape to the case? Do I just use another tape to fix it back after reconnecting the connector?
thanks so much for your suggestion!!!
I found the froblem in the flex connector in the left side (see picture).
There was too pressure on this.
Now the phone runs perfectly!
lunagio said:
thanks so much for your suggestion!!!
I found the froblem in the flex connector in the left side (see picture).
There was too pressure on this.
Now the phone runs perfectly!
Click to expand...
Click to collapse
Good news
... and that pic of yours shows both the connectors that can cause problems.
Mike
hi, i have the same problems but i only had problems with it after flashing my rom to WM6.5... please help.. thanks!
I had a similar problem with my X01HT. Replacing the front buttons fixed the problem, seems like the original front buttons were worn out after intensive use.
Dear All,
I'm a NuB here and have a problem with my Battery Cover, As all knows, as we slide back the battery cover the phone goes off, and my problem: my phone is restarting even with a little tap on the cover. I wonder whether we could disable this matter or it is a mechanical process.
your help would be appreciated.
Any Ideas?
Any Ideas?
What the Newbie!!!
I think you have Magician (i-mate jam or....) phone cause the prophet phones doesn't have this option.
catzillaboy said:
I think you have Magician (i-mate jam or....) phone cause the prophet phones doesn't have this option.
Click to expand...
Click to collapse
Hey Pal, I know that I have Prophet Qtek S200 , and I handle this problem with a peice of paper betweeb battery and cover
What the!
majid.k said:
Hey Pal, I know that I have Prophet Qtek S200 , and I handle this problem with a peice of paper betweeb battery and cover
Click to expand...
Click to collapse
I have one , but it doeasn't have that ability !!!!
I mean I can take out the back cover without restarting or power off.
that's impossible guy!! but I think you have the battery problem,Coz I had same Prblm with my Diamond with fake battery or the old ones, you can change and test that piece!