Related
HI too all in this forum i am new one in this
please guide me step by step the procedure to unlock it
Device Information
Rom Version: 3.14.40 ENG
Rom Date: 11/26/02
Radio Version: 6.18
Protocol version: 324e4
Model No: PW10B1
Plateform: Pocket Pc
and when i enter the test mode by pressing 3 button power+action+reset
they show
wallaby
bootloader
v5.15
Gsm ok
please guide me step by step
wbr
Ahsan MOosai
wbr
Ahsan Moosani
unlocking it
Hi to you too,pal! Well don't have to enter the test mode.
First try to install the xda unlock exe file fm this site,and then open it fm your ppc.
If the attept fails,find and download the special rom or rom kitchen,to overwrite a new rom which provides the use of any network.
Finally I've discovered a tip,on sx56.When is asking for SID lock code not PIN,type the number zero eight times.
Moosani said:
HI too all in this forum i am new one in this
please guide me step by step the procedure to unlock it
Device Information
Rom Version: 3.14.40 ENG
Rom Date: 11/26/02
Radio Version: 6.18
Protocol version: 324e4
Model No: PW10B1
Plateform: Pocket Pc
and when i enter the test mode by pressing 3 button power+action+reset
they show
wallaby
bootloader
v5.15
Gsm ok
please guide me step by step
wbr
Ahsan MOosai
wbr
Ahsan Moosani
Click to expand...
Click to collapse
I just unlocked my TMO XDA 1 ... it was painful! Here's a lesson's learned checklist.
1. Get a SD card reader/writer. ~$20 @ CompUSA.
2. Get a 64M SD Card for Bootloader flashing your unit.
3. Build a 3.17.03.exe ROM image at Yorch kitchen.
4. Backup current CE+boot to your 64M SD card. Enter Bootloader, wait for a "GSM OK" message to appear, press contact button next to speaker. Scroll down to Boot+CE->SD, select. This will copy current ROM to SD card.
5. Take this sd card, put in sd card reader/writer and using OSImageTool.exe (part of XDAtools), copy card to pc folder called CurrentROM or similar.
4. Remove sim & sd card from unit.
5. Put in cradle & connect to pc. Using a guest partnership is okay.
6. Run the 3.17.03.exe file. Mine failed. Couldn't read device config. Said to check USB/serial cable connection.
7. Went back to Yorch kitch, created 3.17.03.nb1 file, downloaded it, copied to SD card via sd card reader/writer & OSImageTool.
8. Insert this sd card into your unit, enter Bootloader & it will ask if you want to load this O/S, do so. This worked for me. Do a hard reset after successfully completion and when it comes up, it states unit is sim locked, do you want to change this, tap Yes. I copied XDAunlock.exe to unit, via A/S to confirm unit was really unlocked. XDAunlock confirmed unit was unlocked.
9. Problem, flashing to 3.17.03 put phone model to PW10A1, mine is PW10B1. Any .exe ROM upgrade software will not work. They "see" a model A and they're configured to install software for a model B ... at least in the USA.
10. To get around this, I put a ROM4.00.21.nb1 on the SD card via sd writer, upgraded unit's ROM via Bootloader. This was successful and model was put to PW10B1.
11. Then I ran my ROM4.01.00.exe which completely finished installing the RSU & ROM on my unit. The advanced copy of TMO's ROM4.01.00, RS6.24.01 is combined into an .exe. I'm sure .nb1 and .nbf exist.
I'm running an unlocked TMO XDA 1 and just packaged it for selling. Good luck.
i send the xdaunlock file in my ppc and open it but they show error erro to getting code , i send the file with infra red and open it in start>programes>filexplorer>mydocuments
but show error
i have only usb cable and infra red
please guide me
and its hard to purchase com cable from any other site just give me schematic and pinouts for cable i will make it by my own
wbr
Ahsan Moosani
Your ROM version is too old: if you install the XDA-developers Special Edition ROM it will provide you with some new features, and resolve your SIMlock problem as well.
Note that this will involve cold-booting your device, so backup all your information first.
how i update to rom because i have only usb cable which comes in box
there is any other way to make cable because it is hard to purchase for me give me schematic and pinouts etc.
wbr
Ahsan Moosani
you don't need a serial cable to flash your xda. just got to the kitchen at www.yorch.net. cook a ROM based on 3.17 and select the exe method. down load the file to ur PC and connect the xda to the cradle and make sure it's connected to power. run the exe file and follow the instructions.
good luck
@Biso007
thanks for reply me
but how download the file i find many things but not 3.17
could u give me complete link to download
thanks in adv.
wbr
Ahsan Moosani
XDA-developers-SER-v12
i download this from another site
this is the right thing to cook my palm on 3.17 check it
please before done any thing i want confirmation
i dont want to loose my palm
Thats the one, go ahead, make sure you back up your data first.
i received new phone from america and its locked
i did not make any things in it now they need to make backup
or not
wbr Ahsan Moosani
3.14 T-Mobile
g32e4
6.18
I want to use my phone in Vodafone in Spain. So I need to unlock.
I have the unlock tool from XDA but it says 'error getting unlock code'
this is due because it is incompatible with the version of ROM/Software I have on my PDA.
Now, I have a small problem. I dont have the USB cables, (I want t buy them but I cant find them ANYWHERE...if any of you know...that would be of MAJOR help.)
Is there a way around that? Is there a tool for my version?
Can I do this via my SD Card?
http://www.romkitchen.de/
Is this site worth trusting? What would I select to make my phone unlocked? I see on that site a rom for Spain's Telefonica (which I could easily make the switch to, and I wouldnt need to unlock phone?)
Can anyone explain to me the process?
Thanks!
hi,
Sum1 here who a T-Mobile subscriber? I have a T-Mobile PocketPC that I need to unlock tho I'm not a T-Mobile subcriber. I need a T-Mobile mobile number to get the upgrade at http://www.t-mobile.com/products/handhelds/pocketpc/download_popup.asp
Or if someone already downloded the upgrade where can I download it without keying-in the mobile number? Thanks.
BTW, I have a question, if I download the upgrade, can I now use the XDAunlock.exe file here (is my ROM automatically updated)? My ROM version now is 3.14.40 ENG. I'm having trouble with the ROM updater here since im not linux literate.
Email me at [email protected]. Thanks a lot
I already downloaded the TMobile upgrade. Can somebody tell me if this upgrade will indeed upgrade my ROM to the correct ROM version with wirelss modem feature to I can use the XDAunlock.exe to unlock my xda? Thanks
The answer is NO, the latest TMO upgrade is 4.01.00 and it has no wmodem.exe application. If you need to unlock your device, go to www.xda-developers.com/XDAunlock/ and use the tool there.
If it doesn't work, try the kitchen at www.yorch.net and cook a new 3.17 based ROM and flash your XDA and unlock it, then you can upgrade to TMO 4.01.00 later.
BTW, the TMO upgrade affects the RSU part. So, unless you are a TMO user you better use the .nbf file only with either SD card or use the XDAtools to flash your device.
Good luck.
Hi Biso,
How can I "cook" a rom? http://kitchen.romanweb.com/kitchen/index.php when I go to that website, the only thing needed to be selected are the 3.17.03 ENG O2-Euro (6656 kB available) and XDA-developers AutoConfig data (113 kB) under it. and the unlocking option right? This wil be the first to use my pocket pc device, which option should I select under How would you like your ROM?
installer EXE
zipped NK.nb1 (SD-card flashing)
zipped NK.nbf (advanced users)
and should I do anything on the NBF header string?
Thanks man.
If I use the intaller EXE file, how will I "flash" it on my device? What are the differences between using the exe,nk.nb1 and nk.nbf? Thanks again.
I notice that above the page there is an indication, by default when I go to the page (without checking or unchecking anything) the top of the page states:
space in ROM: 6656 kB
used: 7729 kB
free: -1072 kB
*overload*
Should I limit my ROM on 6656 kB (meaning that I have to uncheck other options)? My deveice is an XDA 1. Thank you.
Hi ...
Yes, you have to uncheck some optional s/w till the guage line is "Green".
If you are not familiar with the SD method, just select the EXE type. It will generate a 15 MB exe file which you should download it to your PC. Connect your XDA to your PC throught the cradle and ActiveSync and run the exe file while the cradle is connected to the power supply and follow the instructions on the screen.
Good luck.
Thanks man for the quick reply.
Sorry I'm getting confused. Should I transfer the exe file to the device and run the exe file on the device?
Thanks again
The exe file runs from your desktop, your xda will need to be synced with your pc before running the exe.
Thanks so this is what I have to do:
First sync my device (cradle connected to the power supply) and after synching, run the exe file on my desktop computer (no need to transfer on my device or anything?). That's it?
Is this fail-proof? Will it not damage my device if ever there was an interruption or sumthing? How can I make sure that I can go fail-proof? Kinda worried coz I just got hold of my xda 1 (T-Mobile edition), I'm a palm user before. Thanks
BTW, my PocketPC Version is 3.0.12039 (Build 11178). ROM version 3.14.40 ENG. I don't know if my PocketPC is 2002 or 2003. I'll be using the yorch.net ROM (http://kitchen.romanweb.com/kitchen/index.php). All compatible?
ROM 3.14 is a PPC2002 one and all ROMs on Yorch.net is WM2003 except the 3.17 one.
Just to ensure it's a safe process, remove the SIM and SD card from the device and stop any running applications on your PC.
Good luck ...
Thans Biso. How bout a step by step guide? Pls pls pls? Id really appreciate it man.
Like
1. Sync the device (Power connected to the cradle)
2. Run the Rom Exe file
3. etc.
Just to be sure. BTW, is the exe file really just 150KB? Is that all I need to unlock my device?
Hi ...
There is nothing really needed more than what you just wrote:
1. Connect the XDA to the cradle and sync while the power is connected.
2. Run the EXE file and follow the instructions on the screen.
BTW, the EXE file should be at least 15 MB, seems your ROM was not "cooked" well .... try again
Ohh ok. I downloaded twice and all I got was 150kb. how will I know that the ROM i got is "cooked" well so I can be free of troubles. Can you just give me a link to the right/"well cooked" ROM? Thanks man.
One more thing, should I run the ROM EXE file while my device is synching or after the synch?
it's still 150 kb. Here's what it says when I view the log
./mkrom.sh: ../../kitchen.local/mkrom-inc.sh: No such file or directoryno files for configid 26220739Cannot fit files in given sectionsError splitting files
seems there is something wrong with the kitchen work space ... it happens sometimes ... no big issue.
You may try this kitchen as well http://lumpistefan.dyndns.org/
P.S: run the EXE file after the device is synced
which one should I pick? Pocket PC 2002 ROM or Windows Mobile 2003 ROM. And what's the difference. Sorry for my ignorance. Thanks for the replies.
Biso,
Can I use an MMC card for flashing? I MIGHT be able to borrow an MMC card. Also, I dont have a card reader but I have a digital camera which I can use to transfer the ROM image from my desktop computer to the card. Would you think it would work? Thanks again man.
will the exe file below work for me?
http://cuba.calyx.nl/~jsummers/XDA/XDA-developers-SER-v12.exe
and
http://www.xs4all.nl/~jsummers/XDA/XDA-developers-SER-v12.exe
This is my Device's Information
ROM version: 3.14.40ENG
ROM date: 11/26/02
Radio version: 6.18
Protocol version: 324e4
Pocket PC Version 3.0.12039 (Build 11178) (Don't know if this is 2002 or 2003 pocketpc)
Pls reply. thanks
Hi ...
1. As the figure tells, WM2003 is the latest than PPC2002.
2. I can recommend to use TMO 4.01.00 as I have it on my device for almost 3 months now with no problems so far (few things have to be tweaked tho), but I heard good news about AT&T 30.09 ROM as well.
3. I can't confirm that MMC can replace SD card. I saw some threads on this but no final results.
4. The answer is NO, the only way to move the NBF file to the SD card is either a card writer or by using XDAtools with the XDA cradle. I don't think the card will be recognized by the bootloader otherwise.
5. SER-V12 is a PPC2002 ROM and useful only if you need to unlock your device (which I believe it's already unlocked).
No I just want to unlock the device, that's it I don;t really want a ROM upgrade, just so happens that I need to have a ROM upgrade to unlock the device
SO I can use the SER-V12? Thanks a lot.
I got yestrday my new T-Mobile MDA vario, its looked & i wanted to unlock it. I tried using the LOKIWIZ02B and used the U option (unlocking),but all time i got the following message:
"copying H:\vario\lockiwiz02\Utils\itsutils.dll to WCE:\Windows\itsutils.dll
Could not update itsutils.dll to the current version,maybe it is inuse?
try restarting your device, or restart activesync
your phone is unlocked...."
But the phone was not unlocked, tried several times,but the same message is back and the phone is still locked.
My MDA vario information is as follows:
IPL 1.06
SPL 1.06
GSM 01.12.10
OS 1.5.4.2
Plase give me a good advise or a solution to unlock it.
OS
Have you copied the .cab file to the phone first ?
if(yes){
Try this : make a backup of the WCE:\Windows\itsutils.dll file. Delete it
and make a new test. If you can't delete it because it is inuse try installing
a kill process tool, kill all processes and delete again
}
The phone was UNLOCKED, I copyed the CAB file to the phone but forgot to execute it, i did it again by the instructions and it works just as expected and the phone is now unlocked - thank You.
Ok, now the instructions...
1 - Unzip lokiwiz.zip to somewhere in your computer
2 - Copy EnableRapi.cab to your Wizard
3 - Execute the EnableRapi.cab in your phone. Wait for it to finish
4 - Guarantee that your phone is connected via ActiveSync with the computer
5 - Execute lokiwiz.bat (on your computer! My inbox is filled with this kind of error) and follow the instructions on your screen...
unlocking
what is suppost to happen ones you hit the U [for unlock] in the DOS box?
On my end nothing happens, the box just dissapears... mine is stil locked...
Hi, I hope someone out there can shed some light onto this problem. This is what I have: Orange SVP M3100; Operator: 14.123.1.614; ROM Ver.: 1.23.61.4; ROM Date: 07/13/06; Radio Ver.: 1.06.00.00; Protocol Ver.: 32.37.7010.01H.
I've downloaded and successfully (I think) flashed Hard-SPL-V7.
Bootloader used to read: HERM100; IPL-1.01; SPL-1.04.
Bootloader now reads: HERM100; IPL-1.04; HERM100; SPL-210.Olipro.
The phone still works and syncs. properly, but when I try running SPV_M3100ROMUpdate_0407, it eventually returns Error 260 (Update utility cannot connect to your PDA Phone.) This happens in Vista Ultimate and in XP Pro.
The program will go as fare as identifying the current image as Ver.: 1.23.61.4 and suggests to replace it with image Ver.: 2.11.61.1 however, when I click on OK, it puts the phone into Bootloader mode, disconnects the USB connection and unable to reconnect again. After this I have to do a soft reset and everything goes back to normal.
I'd very much appreciate any ideas to help me get around this conundrum. Many thanks.
put device into bootloader and try flashing from there, otherwise try sd card
OK, I could not flash from Bootloader either; same error message.
Extracted the SVP_M3100ROMUpdate_0407.exe onto the SD card.
Ended up with the following files: EnterBL.exe; GetDeviceData.exe; README.doc; ROMUpdateUt.exe; RUU.dll; RUUUI.dll; RUU_signed.nbh.
None of the above files will run on the PDA. What do I do next? Sorry for being such a novice and thanks again.
commnet said:
None of the above files will run on the PDA. What do I do next? Sorry for being such a novice and thanks again.
Click to expand...
Click to collapse
Correct, the files are not run from the device.
The hermes wiki has the directions for flashing from an SD card, go check it out.
Thanks for that jdc. I found the information you have suggested and here is what I did so fare:
-Formatted the SD card.
-Renamed the ROM image file to HERMING.nbh
-Inserted the SD card with the renamed image file into the phone.
-Restarted the phone and confirmed that it was reading from the card.
-Put the phone into Bootloader mode by pressing PWR+OK+Reset.
The multi-colour Bootloader screen comes up and nothing else happens. I'd tried pressing the PWR button just in case, but it had no effect.
Any more ideas? THANKS!
SPV m3100 upgrade - error 260 - connection drops when allowing enterBL.exe to run on
Hi - am going through the same process to upgrade my SPV m3100.
I've followed Mr Vanx's guides to the letter - ROM update from 1.23.61.4 to Hard-SPL-2.1 - as soon as i click 'yes' on the phone to allow enter.BL.exe to run - the connection between phone and laptop immediately drops.
I've tried using different USB ports as suggested in different threads = but to no avail
Am running Vista Home Premium.
I'm a novice so sorry for sounding stupid - any help would be really appreciated.
I had the same error until I disabled the phone lock. Worked ok after that
I had this problem for awhile, and I'm using Vista. I can't remember the problem to explain it, but I did one of 3 things to fix it.
1. Follow Mr Vanx's Vista Guide. The most important part is downloading his attached drivers and getting Vista to detect your phone as an "HTC USB Device" or "HTC USB Sync" or something like that.
2. Then I would recommend installing the official ATT Rom, you can download it off of HTC's website.
3. Install Schaps Advanced Config cab, and disable "security warnings"
After this done, you should be able to install a cooked rom from here.
Hi all.
I have been reading in the forum for hours and hours, without beeing able to find an easy way (that I understand) on how to upgrade.
I am an old (retired) man, and not stupid (I hope) but have a slight consentration problem.
I want to upgrade from WM5.0 to Windows Mobile 6.1
(+Opera Mini, support for 8GB SDHC and TomTom 7)
I have: a HTC P3300 ARTE100
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
ROM version: 1.12.405.1 WWE
ROM date: 9/12/06
Radio version: 02.67.90
Protocol version: 4.1.13.28
ExtROM version: 1.12.405.101
The device is not locked (I belive) because I can use any SIM I want in the phone.
I have tried to flash to SPL 1.11.cmon, but ended up with SPL 1.11.0000
So I downloaded and installed HTC_1.12.405.01_026790_WWE_SHIP This put my phone back to original, (SPL 1.12.0000)
Synced and copied enablerapi.cab and Cert_SPCS.cab Disconnected, and ran both of them.
I tried to run start_uspl.exe, but it will only try to update from current rom ver. 1.12.405.1 to ver.9.99
And after a while I get a message on my P3300:
Unable to open log file....
tiny_console_init done
And ROM ver. is back to SPL 1.12.0000
Suggestions anyone?
ok pm me and i will walk you though.
first update to the newest version of active sync thought.
next make sure your device is fully charged.
next back up all data from your device. flashing a new rom will erase all data.
next cid unlock read the first post and download the attachments
http://forum.xda-developers.com/showthread.php?t=308242
after you have done this pm me.
as for opera just download one of the many prepacked opera cabs. here is a link to one that should work. http://forum.xda-developers.com/attachment.php?attachmentid=281464&d=1266292843
to my limited knowledge of sdhc support and the p3300 all of the cooked roms have sdhc support cooked in. so when you get a newer rom on your phone sdhc should work.
Arggggh
I can use any SIM in my phone. Is CID unlock really neccesary?
I downloaded pof's Artemis_USPL and ran it, but it seems nothing was changed.
I too wants to change the ROM ver. from 1.12.405.1 to ver. 9.99
And the link to: HTC P3300 WWE factory rom - is dead.
But I found HTC_1.12.405.01_026790_WWE_SHIP another place.
I have also found and downloaded AndreW82_WM6.1_21056_Lite_v1.4_WWE.nbh
But am afraid to try to install it since my ROM is not ver. 1.11.cmon.
Here is what I have tried so far:
Downloaded Artemis_USPL
Synced and copied enablerapi.cab and Cert_SPCS.cab
Disconnected, and ran both of them.
Booted and Synced.
Started start_uspl
(wich opened a dos window)
After 10....20.... and so on, phone softbooted.
Message on phone:
UNABLE TO OPEN LOG FILE
TINY_CONSOLE_INIT DONE
PDA Phone ROM Update Utility 3.0.3.1 stardet automatically on PC.
Checked: I understand... and clicked Next
Checked an confirmed preparation steps, and Next
New window:
Current version 1.12.405.1
Select from below UPDATE the current ROM version.
clicked on Update
Program then wants to update to version 9.99
Clicked on Next
New window:
This will take approx 10 min, - Next
Phone screen changes to red green blue, runs a bar up to 100%, and the softboots.
Takes about 10 sec, not 10 min.
Error message pops up on PC:
Error 270
Image file is corrupt.
EXIT
Disconnected anf booted phone.
SPL is still the same (SPL 1.12.0000)
___________
Trying again:
Synced
Ran EnableRapi.cab and Cert_SPSC.cab
Did not boot or disconnect, but started start_uspl.exe
10...20... and so on
70% phone-screen goes white
PDA Phone Update Utility 3.0.3.1 pops up on PC.
No reaction on phone, Hard reset.
SPL is the same (1.12.0000)
...
mini z
soft reset when the ruu window opens..
when dos window closes..
ok, now for my question..
my spl is 1.11.cmon so cid is already done and has been for a year, i have flashed several roms so i am not a noob at flashing..
the connection from my pc to artemis dsconnected during flash and now in bootloader.. it wont flash from sd..
i know how to use the mtty commands coz iv used it before, but cant remember how to get it to select USB from the 'port' menu..
*how do you get it to select usb?
i know how to use mtty but cant remember
Ai... I'm sorry man, I've never flashed an Artemis before and I don't have the tools to do it either. Maybe you should ask in #xda-dev on IRC?
...
I.m doing something wrong, but don't know what.
Phone on - connecting USB - phone syncs.
Start start_uspl.exe - at 100% screen goes white.
Softresetting - waiting for sync - then confirming on PDA Phone Update Utility.
(The uspl.zip i got from raving_nanza)
After it has finnished, phone boots - and I still have USPL ver. 1.12.0000
raving_nanza said:
ok, now for my question..
*how do you get it to select usb?
Click to expand...
Click to collapse
PC:
Active sync > File > Connection Settings > Allow USB connections, and select a port. (e.g. COM2)
Phone:
Phone > Settings > Connections > USB to PC > Enable
Then:
Phone > Programs > Active Sync > Menu > Connections > Sync PC's with this connection > Select USB.
Mini-Z said:
PC:
Active sync > File > Connection Settings > Allow USB connections, and select a port. (e.g. COM2)
Phone:
Phone > Settings > Connections > USB to PC > Enable
Then:
Phone > Programs > Active Sync > Menu > Connections > Sync PC's with this connection > Select USB.
Click to expand...
Click to collapse
cheers dude..
try this..
raving_nanza said:
try this..
ruu_signed.rar
Click to expand...
Click to collapse
Hi
Tought I should not try to install the .nbh file if USPL was not 1.11.cmon.
Btw:
One of the first steps is to take out the SD-card. Is that what I am doing wrong?
(Should I copy the AndreW82xxxx.nbh to my SD, and have it installed when I run the uspl/RUU?)
...
this is 1.11.cmon.. just try it..
...
take out sd card..
dont flash andrews rom..
do uspl with the one ive just uploaded on this thread..
raving_nanza said:
take out sd card..
dont flash andrews rom..
do uspl with the one ive just uploaded on this thread..
Click to expand...
Click to collapse
This is obviously where I miss something.
the RUU_signed is a .nbh file.
So how do I start it?
Should I use activesync and put it on the phone and some how start it from there?
Or should I put it in the same folder as the uspl cmon, and then run the uspl?
Or is there another trick that I have missed?
put it in the uspl folder and overwrite the one inside..
then do uspl..
raving_nanza said:
put it in the uspl folder and overwrite the one inside..
then do uspl..
Click to expand...
Click to collapse
"Error 270 Update error"
"The image file is corrupted. Please check uour update utility."
(I am using XP sp3.)
(But this time it at least tried to update from 1.12.0000 to 1.11.nosize)
I also tried renaming the ruu_signed to arteimg.nbh
Seems my phone has some kind of lock on the SPL 1.12.0000.
Can it be write-protected in some way?
And if so, how can I "unlock" the write protection?
I.m doing something wrong, but don't know what.
Phone on - connecting USB - phone syncs.
Start start_uspl.exe - at 100% screen goes white.
Softresetting - waiting for sync - then confirming on PDA Phone Update Utility.
(The uspl.zip i got from raving_nanza)
After it has finnished, phone boots - and I still have USPL ver. 1.12.0000
Click to expand...
Click to collapse
I've made several attempts to install 1.11.cmon, none was succesfull.
Two days ago performed another try, but this time without SR. and it worked
q123456 said:
I've made several attempts to install 1.11.cmon, none was succesfull.
Two days ago performed another try, but this time without SR. and it worked
Click to expand...
Click to collapse
Asuming SR means SoftReset - I tried, but it did not help.
Same Error (270)
So I tried again, and again.
Cert_SPCS.cab and enablerapi.cab without disconnecting nor syncing the phone.
Then start_uspl.exe, and on white screen I just started (or rather continued with) the RUU.
WOOHOO - on 3. attempt my SPL changed to 1.11.cmon
So, if you read this post, and have the same problem as I had, here is how to do it:
Download attached file, unzip it, and read the install.txt
...
1.1.cmon is 1.11.cmon
dont forget to thank POF
glad you done your spl now, which rom you gonna use, i suggest the andreW82 rom or the babbelut rom..
andreW82 +1
I glad, you did it, Mini-Z
raving_nanza said:
1.1.cmon is 1.11.cmon
dont forget to thank POF
Click to expand...
Click to collapse
1.1.cmon was the name of the zip you sent, but OK, I have changed it now.
CREDS for pof is added to install.txt
raving_nanza said:
glad you done your spl now, which rom you gonna use, i suggest the andreW82 rom or the babbelut rom..
Click to expand...
Click to collapse
I have a slight consentration problem, so I forgot that I am only half way.
I have downloaded a couple of .nbh files (AndreW82, Touch 4.02, Tom Black v5.0).
I have not yet decided wich one to use.
I want to install TomTom7 and Opera Lite + support for 8GB SDHC.
Now I just have to figure out how to install one of the .nbh files.