Is it possible, with a registry tweak perhaps (?), to swap the green standby led with the blue one?
Resulting in that you have a blue led blinking instead of the green one..
There is a tweak to turn every led off, but I havn't seen a tweak for this anywhere..
kick
Related
Is there a registry key where we could change the green led to a blue led? I don't use blutooth much anyways so I thought I could have it flashing blue instead of green; just looks cooler imo.
Thnx=)
I don;t think this can be done; So sar no-one has been able to find a hack to disable the blue led for those who don't want it, so if we can't turn it off I suspect we won't be able to hack it to operate for anything else either - I suspect the Blue LEd is hard wired into the BT radio unit and not controlled by software at all. THat way, when the BT radio is on, so is the LED.
This certainly seems to be the situation. It is notable that when BT is enabled, the blue light flashes independently of the green/orange light.
The only solution would be to replace the LEDs, which although tricky should be quite possible.
Skip
This is funny. I'm exactly looking for the opposite: i.e. to restore my flashing led.
I don't know why and which program caused it, but my led is not flashing at all and I don't wanna hard reset.
what do those lights mean?
blue blinking = bluetooth?
orange blinking = recieved a message or call?
green blinking = radio on?
permanent blue = ?
permanent green = ?
permanent blue = ?
and whith indicator for battery and power?
thanx
well permanent orange is charging
and permanent green is fully charged
that's about all, haven't played w/ bt yet
Hi all,
Is it possible to disable (registry tweak or other ?) the blue led of the Artemis' trackball ?
Thanks, Laurent.
...and/or all the other leds? (allledmgr entry in registry does not exist!)
Yes all the LEDS would be great too...
We can maybe find a key that defines the time back-light LEDS are illulinated ? And set the time to zero ?
No idea ?
Ok i will open
blue led and no screen
the blue light is a safety lock i fixed on magic by plugging into charger turning off removing batter led went orange then plug battery back in then it restarted and turned on hope this helps
hello,
my prophet's green LED blinks all the time, when i have a signal.
is there any way to disable this or to manipulate that? for example no blinking or using the red LED for this would be nice.
Yes, have a look here:
http://forum.xda-developers.com/showthread.php?t=282545
thank you for that link
i just purchased a touch hd and was wondering why the led indicator lights are not flashing?
i notice that there is an led indicator light on the power button and also next to the earpiece; from my old tytn II, the led indicator flashed amber for service and also blue for bluetooth.
i currently have service and my bluetooth is on, but i don't have any flashing indicators.
is there a setting to turn them on?
This is not a led is a light sensor.
akhoury said:
i just purchased a touch hd and was wondering why the led indicator lights are not flashing?
i notice that there is an led indicator light on the power button and also next to the earpiece; from my old tytn II, the led indicator flashed amber for service and also blue for bluetooth.
i currently have service and my bluetooth is on, but i don't have any flashing indicators.
is there a setting to turn them on?
Click to expand...
Click to collapse
The one next to the earpiece is a light sensor.
The other flashes green for missed event, stays green for finished charging, amber for charging, and flashes amber if you're low on power.
Is there a registry hack to get the "old" LED behaviour? (Cell locked in=Flashing green, Notification = flashing yellow, Bluetooth = flashing blue etc.)
I don't think there is a solution for this (yet).
in anycase, it is only a bi-colour LED - ie Amber and Green - no blue.
I have the same problem: my green led flashes for missed calls but not for incoming messages.....
Can you help me?
Thanx a lot
Dani3l3 said:
I have the same problem: my green led flashes for missed calls but not for incoming messages.....
Can you help me?
Thanx a lot
Click to expand...
Click to collapse
Start, Settings, Personal, Sounds & Notifications, Notifications, Messaging: New text message, Flash light for....
That LED is so tiny and dim I find it's easier to just hit the power button and look at my screen to see if I have missed calls/texts/etc.
well theorticall you woud have to seek out the powr button with eyes first
kdding
Thanks.....
My HD have an Italian ROM and the translation is poor...... nothing about "led blink"
I've resolved checking a flag translated as "turn on screen if incoming message".........
I think i'll try a WWE rom.....
Thanx a lot
dani, that is the correct option. Italian translations suck
I"m using Pure Nexus and it allows me to set custom LED notification colors. I'm swiping all over the place and can not get the LED notification to turn green, the closest it gets is blue or yellow, no green in between. Anyone have a working HEX code for green?
http://www.pagetutor.com/common/bgcolors1536.png
#33FF00 seems green enough to me?
I mean it's green on the screen but the LED can't display it. It's just yellow.
Edit I got it, it's 00ff00. Copied it from the default her code for a full battery from another setting.