Database Users

Phone wont work

I upgrade my ROM to Pocket PC2003 (T-mobile.nbf) image that worked with no problems using the XDA OS Image tool. It copied over using programme A and following the upgrade I carried our a Radio Stack upgrade to 4.21 supplied by O2. I now have a problem as the phone wont work. I tried re copying the immage again but just before programme A runs a cmd.exe box apears and I get the following message 'ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host.
error getting connectiontype
Programme A then tells me my device is not connected and to check the USB connection. Can any body please help me. All I want is to get my XDA phone up and working again.

Which network are you using, it may be that the bandswitch has chosen 900/1900 which would prevent orange and t-mobile from working, if this is the case enter bootloader, then push the key below the antenna, choose 900/1800 then reboot.

I'm on the O2 (pay as you go) network. There were no problems with my phone and the T-mobile image until I performed the O2 Radio Stack upgrade. I hade already performed this upgrade on my old operating system, before I copied over the T-mobile image. I had no problems with the old OS and the Radio Stack upgrade.

Seamus, if you burn the original O2 rom back to the phone, you will be able to return it to O2 if it is the radio stack upgrade that killed the phone, they should fix it for free.

Hello guys Need some help from the pros
I currently purchased this phone its a Siemis Sx56 AT&T. As i was updating 2 unlock the phone with a dump of another sx56 aT&T that was uncloked (via sd card) it stop in the middle of the proces of uploading the boot of the sd card. Now the phone:
1. Will not start
2. Can not boot the phone to wallaby
3. cooked a rom and tried 2 boot 2 wallaby with no luck
4. 1/2 read & read with no way of knowing what i'm doing wrong
5. how can i repair my bootloader (I used the one in xdtools with no luck)
Than U guys in advance
Luv the Info in the forum.
Adrian
Atlanta GA USA

XDA manipulator

where do i get the XDA manipulator

http://wiki.xda-developers.com/index.php?pagename=XDAmanipulator

Thank you very much LumpiStefan for your timely response and for the link to get the XDA manipulator, i have been looking for it for so long. THANKS DEVELOPERS

I too appreciate the link, I have been searching for this for ages. Cheers.
.......Ib a n e

I really appreciate the link thanks
BR

wallaby usb flashing
hi there ,,can anyone tell why when i enter usb flash mode i cant flash via it wheni try to run a upgrade program it says plug in yor pda and on the pda screen all i get is usb flash mode,,connect usb cable now... but it is lso in my device manager i see my pda as a windows ce devices so what the hell is going on ?
pls dont tell me only way is via sd card surely it can be done via usb lead if so please can some post a step by step on how to flash via usb as i did so already from pc2002 to win2003 using the rom from xda developers and now i get a logo Ozup and underneath says ,,this os image is meant for microsoft employees or technicians bla bla bla
but i can enter boot loader fine access all the menus in bootloder my bootloder version is v5.15
pleaaaase someone help me

There are two possibilities to flash a device:
1. In Bootloader via SD Card
2. Normal booted device via Active Sync
But i do not know what you mean with USB Flash Mode
Stefan

thanks for replying back now i have new problem
i have a big problem and i think your the only person who can help me my problems occured when i went to flash my wallaby device with this rom ftp://xda:[email protected]_ENG.exe/
i wish i never bothered the device was perfectly running fine until i flashed it with this via usb it all was a succes when i done a hard reset i got a screen with a oz up logo and underneath it says "microsoft internal use only" this operating system image is meant for use only by microsoft employees and contractors ,,and the crazy thing is i cannot enter my bootloader which was v5.15 so i can flash it via sd card its vanished no bootloader only that screen and on the bottom right corner it says ,,g32s54,v4.08,3.04 when i plug it in usb all i get is a unknown device and i cannot flash it so please if there is a way even if its pretty technical i would be honoured if you can help me out i would be very grateful if u cn show me a way of getting the bootloader back many thanks

still no bootloader on my wallaby device
hi i,m really upset if i can only get acces to the bootloader i can atleast flash it via sd card so please if theres a way of getting back the bootloader or somehow flashing it back please any help would be appreciated

radio stack
had same sort of problem this is how i fixed it go here
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError
don't use the 4.16 use the rs 4.21 when i did the upgrade i was then able to connect to active sync then changed the rom try the special rom 1.2
hope this helps

mate the problem i have is that i cant acces the bootloader for me to do anything its gone and this happened after using that dodgy rom
all i want to no is there a way of putting back the bootloader on to the device as its not there its been somehow erased after the flash i done

mate if you try what i said to try this should help you to connect your phone back to your pc then you can change the rom from there you shold get bootloader back when you put a new rom on

Help is needed urgently

i dwonloaded and installed T mobile rom from this site
My device is Q tek 1010
i cant install any other rom as this error message appears each time i try to upgrade the rom
"Please find the error message attached"
I need help as the message read the device is not connected however its will connected and active sync can see it fine
Please advice what to do
Regards

The ROM you have currently installed prohibits flashing via Active Sync. You have to flash via SD-Card and Bootloader.
Take a look here how to do this....
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
HTH
Stefan

Can MDA Vario be flashed from SD-Card?

Hello,
I have flashed my MDA Vario with a WM6 rom dutch witch worked fine. After i changed my pagepool to 6 MB and soft rebooted my MDA, it stared, but without phone functionalty. every program i try to start it gives me the message that it has no memmory to start the program.
No activesync connection (or any other connection) can be established. I have found some articles on flashing xda pda's from sd card. But in these articles they talk about .NBH files. The only file i can find in the update util is an .NBF file. Can anyone help me solving this issue?
TNX in advance

Try bootloader mode?
Bijdehandje said:
Hello,
. . .
No activesync connection (or any other connection) can be established. I have found some articles on flashing xda pda's from sd card. But in these articles they talk about .NBH files. The only file i can find in the update util is an .NBF file. Can anyone help me solving this issue?
TNX in advance
Click to expand...
Click to collapse
Can you get into bootloader mode (tricolor RGB bands)? ("Get your phone in bootloader mode by doing this: Phone powered off, press Camera button + Power On, will enter into bootloader mode (RGB screen").
Once in bootloader mode you can reflash even though activesync says not connected - just look for little USB in corner of screen.

Tnx cushcalc for your reply.
I have tryed it just a minute ago. I can enter the boot loader but the flashing fails at starting with the message "This update utility cannot be used for your PDA Phone. Please get newer update utility". I have used the same flash tool as the rom image witch is now on the MDA.

Sounds more like CID locked after flashing the last ROM was flashed....cant u even flash any other wm6 ROM?

You should flash the original T. Mobile ROM from bootloader it should work. After you have the original running you can then re-flash WM6 using shelltool if your phone is CID locked. Try it and lets see how it goes.

You people are the greatest. I have tryed to flash my MDA Vario with the latest rom from t-mobile and now i have a fully functional mda again. BIG TNX for helping!!!

XDA11i Serial V1.01

Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.

Have you tried updating to the latest version of Active Sync on XP
or following the guide for Vista

Take off battery. wait for about 10 hrs. put back battery and switch on the power.

Thanks for the tip's
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway

Furkinl said:
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Click to expand...
Click to collapse
erm u are trying to flash on a pc running vista?? thats your problem, u cannot flash on a vista pc, xp home/pro ONLY!

Thanks for the advice, tried on XP and it worked fine, it would seem that activsync was not required in this case. At least my XDA is ALIVE for now.
many thanks

You simply could revive it again by Resetting it via the stylus

thnx 4 all the soloutionsss
i had same problem , but once i tried it on xp, its works for me, my ppc now is refresh installed,
thnxx

qtek 2020i
for information the french rom is available on this place http://www.planete-htc.com/index.php?mod=download choose dangaard section there is two files to download
1. choose 2020i dangaard rom
you can not use it
2 download the radio file
it contains an exe called upgradeut make it in the directory of your dangaard folder and you will be able to flash it
it work also for pda stuck in serial usb
voila

qtek 2020i
radio file 1.04 two mega

do a hardware resett and it should be the phone back to defaults

XDA IIi V 1.01 Serial /USB
Hello,
I tried to update my XDA IIi from a new rom version found at o2.ie website but my XDA IIi is stuck and showing Serial on top and v 1.01 at botom. When i attach it with cardle it shows USB instead of serial.
I have tried Almost everything that i found on this forum in last three days.
Hard reset / soft reset/ new installation using different version etc.. but nothing worked for me..
Now I am really confused and can't find what to do.. Can any one from XDA gurus/ developer help me and sumarize what should i do?
Thanks in Advance
Zeeshan

Yes, i have the same problem i did exactly what was done above me pls can someone help!!!!!!!!!

Furkinl said:
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Click to expand...
Click to collapse
Where can I download this rom?
Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed
Thanks in advance
Chet

look and lern
put qtek 2020i in stativ (conect to pc via usb)and push power ( on screen will apear USB and v1.01), and you dezarhive :astel_wwe_11100_112_10200_ship, and doble klik on AlUpgradeUt and bios at ppc wil be update !!!!! This is all, the ppc will be now reinstaling, be patient and wait until will be reinstaled (25 min)