I am trying to get my O2 XDA mini to connect to my home network.
When wi-fi is on it picks up my Network as well as two neighbours! However I can't make any connection.
My home network is based on static IPs so I presume I need to configure a connection associated with the in-built Network Adapter. However there are multiple adapters listed - which is the wifi adapter please?
the list is;
AsyncMac NDISWAN-miniport
PPTP NDISWAN-miniport
Remote NDIS-host
L2TP NDISWAN-miniport
NE2000 compatible Ethernet driver
Virtual Ethernet Intermediate Miniport
SDIO WLAN Wireless
Also what is the difference between Work and Internet option? Is this just arbitrary naming of two optional connections?
And is there a way to Internet Explorer default to wifi connection rather than dial-up.
Thanks.
I would think the one that says WLAN (Wireless Lan) in it.
Surely it would be better to turn on DHCP? it does make life so much simpler....
I thought it might be the SDIO WLAN Wireless but the SDIO threw me - I thought it referred to an inserted card.
I change the power/battery settings to performance and it worked.
Related
I can't connect in wifi to my router Linksys WRT54G. I have this problem only between this router and this pda.
Please help me.
Thanks
Is your router set to 11G only, or 11B AND 11G? The Universal can only handle the slower 11B...
Now i can connect, but only if i use manual settings.
I added manually my wireless network and, under network adapters, i set the tiacxwin compatible wireless ethernet to use specific ip address.
And it works.
Now i must be sure that it work in my home too, where it was set all automatic.
:?
I have just purchased a dopod 838. While I enjoy it very much, I do have one problem I don't seem to be able to solve. The problem is as follows: my device finds and connects to my Wi-Fi net, it indicates that the signal is good (and the net is an open one, no need for any password), but even though I am connected, I can not browse the Internet or send or receive e-mails. I tried to find answers in the user guide, but all I find there are generalities. I guess it has something to do with the settings on my device, but it is really frustrating, as the main reason I switched to the 838 modal is the Wi-Fi. I think the problem may be connected to the Network Adapters. When I check the Network Adapters I see the following list:
PPTP NDISWAN Minipot
L2TP NDISWAN Minipot
AsycMac NDISWAN Minipot
Virtual Ethernet Intermediate Minipot
Remote-NDIS Host
NE2000 Compatible Ethernet Driver
SDIO WLAN Wireless Adaptor
The only one that is indicating the IP Address is the SDIO WLAN Wireless Adaptor, but is it the one to use out of the list? And if so, I do I do that? How do I set it to be the default adaptor?
Please help...
Thanks
Benny
I only do the setup one time for my friend. Hope that can help.
If the network hadn't any protect, you can just choice this on the screen when this had been found. It don't need any setup for a unprotected network.
If the network is protected, "password / soid / encrypt". You need to setup a network card, setting > connection > network card , with all the details before you can use the network.
No success
I have many adapters, it seems to me that the only one that is the correct one is the SDIO, but I can not make it the default one.
Internet access through Wi-Fi
If you've created a wireless network between you PC and your device, you need to 'share' your internet access on your PC. Also if you have a Firewall you need to enble that too, for mine it was the generic sub-program 'svchost'. Hope this helps.
no need to set the SDIO Wireless Lan Adaptor to default. That list is just a list and has nothing to do with privilege.
i think the problem is that your Wirelan has some restrictions to access,eg. MAC address. So,ask your network administrator for help ;-)
I have an iMate Jasjar.
WiFi works fine for AvantGo updates and Weather panel updates but Pocket IE and Terminal Server Client refuse to use existing WiFi link! :x
PIE always uses GPRS and if I flight-mode my radio, it simply fails to connect complaining about no GPRS connection! :evil:
Solution:
I installed Opera Browser Beta for PPC. It works over WiFi no problems.
My trial period is nearly up so they'll get some of my money. :wink:
Hi
ihave a O2 XDA IIi and an belkin router
the wireless connection is established and my xda recognise the network but i cannot acess internet
what can i do?
go "setting>connection>network card"
and setup a card for your router.
doesn 't work
I TURN ON WIFI ON XDA IIi the connexion recpgnize wi-fi belkin 54g status connected
start settings/connections/network cards
configure wireless network page
belkin 54g connected
networks toaccess
all available
network adapters page
my network card connects to
work
tap an adaptor to modify settings:
NE2000 compatible ethernet driver (configured with all ip adresses and dns)
L2TP NDISWAN miniport
ASYNC MAC NDISWAN MINIPORT
PPTP NDISWAN miniport
tiacxwln compatible wireless ethernet (configured with all ip adresses and dns)
bluetooth pan user driver
is this ok?
i come back on
configure wireless network page
belkin 54g connected
networks toaccess
all available
i click on belkin 54g
this is what it shows
General
network name belkin 54g
connects to work
Network key
authentification open
data encryption wep
the key is provided for me automatically
802.1x
use IEEE 802.1x network accesscontrol
EAP TYPE PEAP
bUT
start settings/connections/wlan
main
status connected
current config
SSid belkin 54g tx rate auto
modeinfrastructur channel 6
bssid 00-11-50-7F-32-74
MAC 00-09-2D-15-3A-A8
IP 192.168.2.4
SIGNAL QUALITY GOOD
SETTINGS
POWER SAVE MODE
AUTO TURN OFFWLAN IF NOT CONNECTED
LEAP
SSID AUTHENTIFICATION TYPE
BLANK BLANK
IS THIS NORMAL?? SHOULD'n it show
belkin 54g??
when the wifi connected
i play iexplorer
when i type an internet adress
the message : the page you are looking forr cannot be found
thanks for your help..
Have the O2 XDA Exec myself, but the settings should be the same, checked with my Acer N50 to make sure
Leap is blank for me too.
some setting differences betweens yours and mine
neither the NE2000 or tiacswln cards have been touched in anyway, left them as default.
mine is set to connect to 'The Internet'
the key is provided for me automatically is unchecked, I manually typed it in with the key index.
use Ieee 802.1x is unchecked
check the belkin setup page, and see if the XDAIIi is staying connected or it is connecting and disconnecting.
looking at the manual, check the Belkin setup page at Firewall/Client IP Filters and make sure the PDA isn't being blocked there. Also check that the Mac Address Filtering is not enabled, if it is, you will need to add the PDA MAC address into it.
Hi Wytey
Thaks a lot, your configuration works perfectly.
Kisses
hi, im not able to connect to the net with my wizard.
i dont have a wireless router so am connecting directly to my laptop, the ad hoc connection i have made works fine for file tranfers, but not for activesync or connecting to the web in either PIE or minimo.
i know activesync isnt possible but surely i should be able to use the broaband from my laptop?
any pointers would be greatly appreciated. software? settings?
its a t-mobile uk vario with qtek test rom.
also anyone know of a remote control utility, i use logmein but would like something a little more menu/macro based for control of media.
cheers
kevo
Try turning on Internet Connection Sharing (ICS) on your laptop; that'll make your laptop act a bit more like a router, providing NAT services to the Wizard.
yeah i've tried that, and i've just tried bridging connections (dont really know much about that) but that hasnt worked either.
kevo
My configuration
Me too, I use ADHOC connection for my WLAN.
PC configuration:
ADSL connection shared
Adress IP:192.168.1.1 Mask:255.255.255.0
PocketPC configuration:
Adress IP:192.168.1.55 Mask:255.255.255.0 Gateway:192.168.1.1
DNS:80.10.246.2 for Wanadoo
Your problem is certainly the DNS.
You can put 192.168.1.1 too.
so it is possible? cool!.......but im still having problems.
i cant figure out how to enter these settings, not to sure where to put them,
iv tried puttin the DNS in the -> connections -> vpn
and -> network cards -> networks adapters -> SDIO WLAN Wireless Adapter
sorry to be a pain, but could you point me to where to get each address and where to put them?
also is there anything particular you did to set up the adhoc network? i just used the Windows XP wizard and then ticket the AdHoc option after.
my laptop is conected to the router and the router is connected to aol adsl.
the ip address of my laptop is showing as a simple 10.0.0. number on the LAN but "Autoconfiguration IP Address. . . : 169.254.235.147" for the WLAN
none of my setup has a static ip address, could this be causing the problems?
thanks
kevo
It's more hazardous without static adress but it's can work.
My PC has directly access to the Internet with a ADSL modem.
It's here (network cards -> networks adapters -> SDIO WLAN Wireless Adapter )
Apparently, it's ok for your PC and the Ad-Hoc mode.
Maybe, you should have your adress IP WLAN on the same network adress of your router.
I GOT IT WORKING!!!
I started again from scratch.
set a new WLAN. added new setup to the vario, added the DNS etc to the vario.
the problem i was having was the way i was sharing the internet connection, i was trying to shared the internet from the wireless to the lan rather than the internet from the lan to the wireless (if that makes sense to anyone!!!). i also ticked all the connection sharing services to allow them, just need to go through them and see which i dont need now.
thanks for the help guys
kevo
(its showing my transfer rate as 11Mbps, although i think iv done the G tweak and my laptop says its got a G card. what speeds should i be getting?)
Hi!
I have an Indian Tablet called penta T-pad, and I have problems connecting with Tp-link Td-W8901G router. The First one is that the tablet doesn't connect instantly to the router using Wi-Fi . it shows in the Wi-Fi network list that the Wi-Fi access point is "saved, secured with WAP/WAP2", And it doesn't connect until I tried several times and when it connected (this is the second problem) it sometimes doesn't send or receive and data. And I have tried resetting the tablet and the router and changing the broadcast channels and use static IP... But, this doesn't work.
By the way, other devices (smart phones, laptops...) can connect to the router without problems, and my tablet was working well during the last six months connecting to the same router. And now, it can connect to other routers or access points (i.e. portable Wi-Fi hotspot).
Thanks in advance, I am looking forward to your replays.
WiFi connection issues.
diana oulaby said:
Hi!
I have an Indian Tablet called penta T-pad, and I have problems connecting with Tp-link Td-W8901G router. The First one is that the tablet doesn't connect instantly to the router using Wi-Fi . it shows in the Wi-Fi network list that the Wi-Fi access point is "saved, secured with WAP/WAP2", And it doesn't connect until I tried several times and when it connected (this is the second problem) it sometimes doesn't send or receive and data. And I have tried resetting the tablet and the router and changing the broadcast channels and use static IP... But, this doesn't work.
By the way, other devices (smart phones, laptops...) can connect to the router without problems, and my tablet was working well during the last six months connecting to the same router. And now, it can connect to other routers or access points (i.e. portable Wi-Fi hotspot).
Thanks in advance, I am looking forward to your replays.
Click to expand...
Click to collapse
You mentioned you are using WAP/WAP2 for security, but have you entered the password or entered it correctly?
Does your router have the ability to add users?
If so, then activate this option and enter the MAC for every device you need to grant access through.
I looked for more information on your router, but could only locate this:
TD-W8901G Model Features and Specifications :
High speed DSL modem, NAT router and wireless access point in one device provides one-stop networking solution
54Mbps transmission rates, better for wireless network surfing or downloading
QoS enables smooth IPTV streaming and lag-free online gaming
Easy Setup Assistant provides quick & hassle free installation
SPI and NAT firewall protects end-user devices from potential attacks across the Internet
Port VLAN binds specific LAN ports and PVCs for differential services
Annex M allows for doubling the upstream data rate to 3.5Mbps
Auto-reconnect keeps you online indefinitely
TD-W8901G Model Technical Specifications :
HARDWARE FEATURES
Interface 4 10/100Mbps RJ45 Ports
1 RJ11 Port
Button 1 Power On/Off Switch
External Power Supply 9VDC/0.85A
IEEE Standards IEEE 802.3, 802.3u
ADSL Standards Full-rate ANSI T1.413 Issue 2, ITU-T G.992.1(G.DMT), ITU-T G.992.2(G.Lite)
ITU-T G.994.1 (G.hs), ITU-T G.995.1 , ITU-T G.996.1, ITU-T G.997.1, ITU-T K.2.1
ADSL2 Standards ITU-T G.992.3 (G.dmt.bis), ITU-T G.992.4 (G.lite.bis)
ADSL2+ Standards ITU-T G.992.5
Dimensions ( W x D x H ) 6.4×4.2×1.1 in. (165×108×28mm)
Antenna Type Omni directional, Detachable, Reverse SMA
Antenna Gain 5dBi
WIRELESS FEATURES
Wireless Standards IEEE 802.11g, 802.11b
Frequency 2.400-2.4835GHz
EIRP 20dBm(EIRP)
Wireless Security Support 64/128 bit WEP, WPA-PSK/WPA2-PSK,
Wireless MAC Filtering
SOFTWARE FEATURES
Quality of Service QoS Remarking based on IPP/ToS, DSCP and 802.1p
Port Forwarding Virtual server, DMZ, ACL(Access Control List)
VPN Pass-Through PPTP, L2TP, IPSec Pass-through
ATM/PPP Protocols ATM Forum UNI3.1/4.0,
PPP over ATM (RFC 2364),
PPP over Ethernet (RFC2516),
IPoA (RFC1577/2225),
PVC – Up to 8 PVCs,
Advanced Features Traffic Shaping(ATM QoS) UBR, CBR, VBR-rt, VBR-nrt;
Dynamic Host Configuration Protocol (DHCP), DHCP relay;
Network Address Translation (NAT); PVC/Ethernet Port Mapping
VLAN, 802.1P, Static Routing, RIP v1/v2 (optional);
DNS Relay, DDNS, IGMP snooping V1/2, IGMP Multicast, UPnP
Security NAT Firewall, SPI Firewall, MAC / IP / Packet / Application / URL Filtering, Denial of Service(DoS), SYN Flooding, Ping of Death
Management Web Based Configuration(HTTP), Remote management, Telnet management, Command Line Interface, SSL
for TR-069, SNMP v1/2c, SNMP over EOC, Web Based Firmware Upgrade, CWMP(TR-069), Diagnostic Tools
OTHERS
Certification CE, FCC, RoHS
Package Contents TD-W8901G
External Splitter
RJ-11 Telephone Cable
RJ-45 Ethernet Cable
Quick Installation Guide
Resource CD
Power Adapter
No other information on actual WiFi setups were able to be located. I wish I could be of more assistance.
Hi I have very similar problems with my devices!
I noticed it is extremely popular problem being discussed everywhere, but no general solution is ready yet, neither straight way of diagnostic...
Only some particular solutions sometimes appear, but they are for particular cases, usually involving deep and accurate adjustment and "pairing" of gadget and equipment.
It would be good to know any general tips like where to look for any info about the wifi connecting process, what are the possible reasons to fail to connect when the signal is high, wifi is visible, password is 100% correct, etc.
Perhaps we can find the log of wifi connecting process, switch it to debug mode, show to experts?
Please, experts, we are all waiting for your replies!