MDA VARIO WIFI PROBLEMS - 8125, K-JAM, P4300, MDA Vario General

I CAN GET CONNECTED TO WIFI, BUT EVERY TIME I TRY TO LOAD A PAGE IT EITHER SAYS PAGE NOT FOUND, OR SOMETIMES THE IP ADDRESS GOES BLANK, CAN ANYONE HELP ME

skip the caps-lock.
what does the logs in your AP says? do you get an ip from your AP? tried to connect to any other AP's?

hey
soz am new to these phone whats a AP?

AP->acces point, so did u try connecting to different wireless APs?

hello
no i didnt, gonna try today see if it works

just checking .. you are not connected via activesync at the same time right ?

hello
no am not, thanks
have u used this program to unock your fone?
0.2a: CID unlocking abitity FIXED

Related

Does anyone know how to unlock mine?

hi to everyone,
i have a locked-SIM t-mobile phone edition which i tried to unlock using a serial cable & the manipulator.
the problem is that the manipulator can't find the device after scaning COM port.
i have checked that the port is not blocked by any program including the synchronization programs but there was no luck.
anybody knows what is the problem in my situation?
Be sure to press SIMULTANEOUSLY both power button AND reset with your stylus. This will bring your T-Mobile to WALLABY mode. After the screen reads GSM OK, connect the cable to your phone and PC and run manipulator.
This should work. I have the same T-Mobile and it worked with mine.
There have been posts with reports where people have had problems connecting to the pda because they have been using a laptop...
I unlocked mine on a SONY VAIO laptop successfully.
hi again,
i have tried the exact steps for unlocking but still the device wans't detected by the manipulator.
the synchronization program also can't detect the device if it is pluged using the serial cable.
could anyone please help me? i couldn't use the phone since 1 month.
Try 75656354
Wasn't there in any thread the hint to uninstall ActiveSync to get the manipulator to work?!?!
Search here in the forum. It wasn't posted as long time ago.
Or just try it when you uninstall.
I ment that there was a problem because active sync wants to connect to the XDA/MDA when connecting it to the serial....
Regards
LumpiStefan
Remember you must have the XDA in bootloader mode.

Upgrade ROM, but it failed...Help!

I have a Siemens SX56, locked to AT&T.
I downloaded the new 1.1 ROM, (Jeff's courtesy)
and began the upgrade.
It started, My SX56 said "Upgrading It will take about 5 minutes...."
Then,
I got an error message on my computer about com ports not being available, it lost the active sync connection, and now my SX56 is hung on the same message: "Upgrading It will take about 5 minutes....."
Of course, I'm unable to connect back.
Any suggestions?
I'm trying to be able to use it with T-Mobile.
I was unable to get any results by pushing the hard/battery resets.
Thanks!
"COM ports not being available"... Are you using ActiveSync via serial cable or cradle?
If you really cannot connect anymore, I guess you have to use an SD-card and the bootloader method to get back to a working state. But do try to reset the device and restart Programme A., it may just pick up again. I've seen that happen here once.
Try doing a soft reset then put it back in the cradle, the upgrade should restart automatically.
AlexF said:
I have a Siemens SX56, locked to AT&T.
I downloaded the new 1.1 ROM, (Jeff's courtesy)
and began the upgrade.
It started, My SX56 said "Upgrading It will take about 5 minutes...."
Then,
I got an error message on my computer about com ports not being available, it lost the active sync connection, and now my SX56 is hung on the same message: "Upgrading It will take about 5 minutes....."
Of course, I'm unable to connect back.
Any suggestions?
I'm trying to be able to use it with T-Mobile.
I was unable to get any results by pushing the hard/battery resets.
Thanks!
Click to expand...
Click to collapse
Hi Alex,
The same thing happend to me.Could you solve this problem?
If yes,can you pls.tell me: [email protected]
Brgds
rats
Were or are you using a USB hub? If so that may be your problem. The SD Card method works very well and very reliably. No comms outside of the device. I found many times whenn trying to do file xfers to the XDA that for no reason in the middle of transferring a file the connection would be lost.
I haven't had this problem with 2003 and AS 3.7.
USB Problem
Hi Alex and Rat,
i got same problem also, after step 4 my XDA screen become white and hang, if you already solve this problem please send me how to fix it this problem to [email protected]. Do you know how to install wallaby bootloader also.

Wizard Hangs..is dead like a BRICK

Hi Wizards,
Im having a Qtek 9100 and using a ROM cooked by Mfraazz. The phone application seems to hang and i have to reset in order to make it functional...the problem does not end here. When the phone boots up, the start menu bar is not visible...I have to hard reset my device 3 -4 times..thats whn the start menu is visible..
I have only one application(Good Link) running...plz help me guyzz
it is time to donate to XDA-developers!
Just reflash the ROM, friend. Seems to be a bad flash to me.
deleted this post
wiztek said:
Hi Wizards,
Im having a Qtek 9100 and using a ROM cooked by Mfraazz. The phone application seems to hang and i have to reset in order to make it functional...the problem does not end here. When the phone boots up, the start menu bar is not visible...I have to hard reset my device 3 -4 times..thats whn the start menu is visible..
I have only one application(Good Link) running...plz help me guyzz
Click to expand...
Click to collapse
try another cooked ROM or an official one and see if problem persists...
the mfrazzz crossbow reloaded made my kjam hang on the bootloader as well n my fone cant b detected by active sync either plz help how m i suppose to flash another rom wen active sync itself dont detect my rom
z0d1ak said:
the mfrazzz crossbow reloaded made my kjam hang on the bootloader as well n my fone cant b detected by active sync either plz help how m i suppose to flash another rom wen active sync itself dont detect my rom
Click to expand...
Click to collapse
Rom has got nothing to do with Activesync not detecting your phone,it's most probably the problem of Activesync application or your USB cable not establishing connectivity.Check the usb connectivity for problems.To verify the connectivity,check if it gets charged via usb connection.
secondly,get your phone into bootloaders and connect it to your Pc via usb cable,see if usb appears at the bottom of the bootloader mode (multicolor screen),if it then it's connecting.
You don't need Activesync for flashing a Rom to your phone,it's done via usb cable,and while flashing activesync is automatically turned off by the Ruu.So if you are able to establish connectivity via usb cable in bootloaders (multicolor screen) you can flash to any Rom.
Cheers

o2 xda mini S help

i have recently purchased this phone and it is currently locked to t-mobile. I am a canadian resident using rogers network. when i turn the phone on it says NETWORK IS LOCKED PLEASE INPUT UNLOCK CODE. I know this number is generated by the IMEI if i remember correctly..... i just dont know how to go about accomplishing this. also ...my computer isnt recognizing it VIA USB............ i am just so at a loss for what to do ...please someone help
oh yeah the IPL is 1.08 and the SPL is 1.08 when i get to the bootloader screen that is all that comes up
As your phone is SIM locked,only t-mobile sim will work on it,but if you want to use any other network sim,you got get your phone SIM unlocked,to do so follow the instructions in the guide and perform the method correctly to get it sim unlocked. Check out this link for the sticky and guide:-
http://forum.xda-developers.com/showthread.php?t=249474
Good Luck
zabardast_1 said:
As your phone is SIM locked,only t-mobile sim will work on it,but if you want to use any other network sim,you got get your phone SIM unlocked,to do so follow the instructions in the guide and perform the method correctly to get it sim unlocked. Check out this link for the sticky and guide:-
http://forum.xda-developers.com/showthread.php?t=249474
Good Luck
Click to expand...
Click to collapse
as much as i would love to do the unlocking myself i cant even get the phone to connect to my computer VIA the USB cable everytime i try i get the " USB device has malfunctioned " so no go there. i cant even activesync it .
zabardast_1 said:
As your phone is SIM locked,only t-mobile sim will work on it,but if you want to use any other network sim,you got get your phone SIM unlocked,to do so follow the instructions in the guide and perform the method correctly to get it sim unlocked. Check out this link for the sticky and guide:-
http://forum.xda-developers.com/showthread.php?t=249474
Good Luck
Click to expand...
Click to collapse
as much as i would love to do the unlocking myself i cant even get the phone to connect to my computer VIA the USB cable everytime i try i get the " USB device has malfunctioned " so no go there. i cant even activesync it .
hoffmanbiker said:
as much as i would love to do the unlocking myself i cant even get the phone to connect to my computer VIA the USB cable everytime i try i get the " USB device has malfunctioned " so no go there. i cant even activesync it .
Click to expand...
Click to collapse
ok,
If there's a connectivity problem,there are a couple of things to verify it.First which windows are you using,if its winvista,you'll have problems,activesync doesn't work with vista,secondly its not recommended to work on vista.So get on with winXP and also get Activesync version 4.5 the latest.In activesync check the option 'allow usb connections' and in your phone goto settings---> connections and 'uncheck' 'establish all network connections' or something and then try to establish activesync connectivity.If still fails,than,
2. verify usb connectivity with pc, to do so get your phone into bootloaders mode (multicolor screen) by pressing and keep holding down the camera button and simultaneously push the Power On button,your phone will wake up and go into tricolor screen (Bootloaders mode)with ipl/spl showing in red colors.When in bootloaders,connect your phone with pc via usb cable,if a small usb appears at the bottom of the tricolor screen,then its has connectivity,but if doesn't appears,then you have a connectivity problem,so:-
a. either your usb cable is faulty,get a new usb cable and try again.
b. or usb input slot of your pc is not operating,try with a different usb input slot of your pc or even try out on an another pc.
c. Mini usb port of your phone is broken,get it repaired or replaced.
check out all these options and rectify the problem.
Cheers !
ok just to verify i am using wins XP and i have removed entirely activesync, reinstalled it checked to see if there is connectivity VIa boot loader and still it comes back that there is a usb malfunction is there ANY drivers i might need?
dude dont know about your unlocking problem, would be nice to hear that youv solved it... wouldnt it be nice if this world had no problems? but then saying that this forum would not exist... and troubleshooters wouldnt have jobs! lol
a) Unlocking NO...
b) active sync... Bluetooth... just rememberd you cant get in can you? to connect ia bluetooth?
email me privately on [email protected] and i may be able to help you if not ill find a way... a bit lost in the head (Attention Dissorder) cant focus...
sori
Sham

how to upgrade the bootloader?

does anyone know how to upgrade the bootloader on the himalaya at the moment mine reads at the top of the screen SERIAL and at the bottom V1.01.
I have a file which i think is a upgrade [boot_1.06.nb0]
but i have to need to know the do's and dont's as i would think this would be if done wrong brick my himalaya?
any help or links would be thankfull?
advanced15 said:
does anyone know how to upgrade the bootloader on the himalaya at the moment mine reads at the top of the screen SERIAL and at the bottom V1.01.
I have a file which i think is a upgrade [boot_1.06.nb0]
but i have to need to know the do's and dont's as i would think this would be if done wrong brick my himalaya?
any help or links would be thankfull?
Click to expand...
Click to collapse
The only one question is
Why the hell you want to do that?
I have 1.01 also on my second today-use himalaya and it is really stable and works same as 1.06, but has some debugging output in mtty which is so useful
I tried also to upgrade it and I failed.
I have an O2 XDA II with windows mobile 2003 on it.
When in Bootloader Mode it says v1.01
when connected to the PC it says USB so i know its working in its own little way
I am trying to upgrade it to windows mobile 6.5.
I have tried everything so far and searched forums and tried things suggested on them but i just cant seem to do it.
Can someone send me a guide on how to do it please.
id be very greatful.
Thanks in advance.
mikeymcmk said:
I have an O2 XDA II with windows mobile 2003 on it.
When in Bootloader Mode it says v1.01
when connected to the PC it says USB so i know its working in its own little way
I am trying to upgrade it to windows mobile 6.5.
I have tried everything so far and searched forums and tried things suggested on them but i just cant seem to do it.
Can someone send me a guide on how to do it please.
id be very greatful.
Thanks in advance.
Click to expand...
Click to collapse
Hay mickey tell me that are you able to sync data or contects,msgs etc with system without disconnecting ?????????
or sometimes connection disconnects automatically ????/
if yes then put something stable thing in between data cable & device.
reply soon
KAASHP said:
Hay mickey tell me that are you able to sync data or contects,msgs etc with system without disconnecting ?????????
or sometimes connection disconnects automatically ????/
if yes then put something stable thing in between data cable & device.
reply soon
Click to expand...
Click to collapse
if anybody have same problem do as per my suggestion
put something in between data cable & device if you connect it without disconnection then it works flash the rom after putting it in bootloader mode
Don't do it
the bootloader is the main program which executes the system programs so avoid to upgrade bootloder.
the result will be permanent damage to your lovable device...
it can't boot more. so be careful.
no need to upgrade it as per my suggestion.

Categories

Resources