Related
Hi all, i have developed this weird problem in my jasjar and i'm sure it's some settings that need to be changed somewhere and not the battery itself. When i first got the jasjar, it gave me a good 48 hours battery backup on standard use but i lost my charger and started using usb to charge it. it's since then that my jasjar drains the battery in less than 12 hours. i have tried replacing 3 batteries but to no better effect. I remember reading something about the Li ion polymer batteries having the memory effect or something and how to reset that in the bootloader mode. if you guys could help me figure it out and fix the problem, i'd appreciate it! here's the details of my rom.
R:1.13.00
G:42.47.p8
D 2.01.06 wwe
the rom is the wm6 from jwright.
(nb: i had the same problem with my shipped wm5 rom and i thought upgrading it would help but it didnt apparently).
How long do i need to use the battery to check the drain thingy. the reseller tells me to use it for 2 weeks before judging it. i'm screwed with having no battery life to this otherwise beauty of a device! if i could get any help, it would be much appreciated. thanks in advance. (josh).
Had the same problem, been happening all week, the phone would just switch of even though it registered over 80% charge. no i am happy again because i read on the forum that you need to totally discharge the battery occationally for it to get to a full charge, it appears that there is some sort of memory effect where the battery thinks it is nearly discharged, try it, i am sure you will find that it workes.
Had the same problem, been happening all week, the phone would just switch of even though it registered over 80% charge. now i am happy again because i read on the forum that you need to totally discharge the battery occationally for it to get to a full charge, it appears that there is some sort of memory effect where the battery thinks it is nearly discharged, try it, i am sure you will find that it works.
awright...i'd try it. thanks for ur help.
mayer said:
Had the same problem, been happening all week, the phone would just switch of even though it registered over 80% charge. now i am happy again because i read on the forum that you need to totally discharge the battery occationally for it to get to a full charge, it appears that there is some sort of memory effect where the battery thinks it is nearly discharged, try it, i am sure you will find that it works.
Click to expand...
Click to collapse
thanks..
I too has a similar problem but this method did not solved my prob as my jasjar switches off by itself at 40%.
I had a similar problem a couple of weeks ago as a charge would last less than 24 hours when I used to be able to last 2-3 days.
Soon sorted it when I found that the Jasjar had decided to disable the automatic switch off, now a charge is back to lasting 2-3 days.
Mike
Had my MDA PRO for 1.5 years, and never had this problem. Battery lasted for 2-4 days on average, although now I have a 3200mAH battery it lasts for well over a week on a single charge
Lithium ION and Lithium ION Polymer (the HTC Universal uses the latter) do not suffer from any "memory effect". The only battery type that does to any significant extent is Nickel Cadmium, which is rarely used these days.
It's also impossible (well, almost) to completely discharge Lithium ION Polymer batteries - internal circuitry in the battery shuts down the cells when the charge gets too low, at up to 10% charge. This is because a completely discharged L.I.P. battery becomes unstable, broken (unable to be recharged), and runs the risk of explosion or leaking in this state. So don't attempt to drain those batteries completely dry folks - it's dangerous! Letting them run down naturally in your Universal should be safe though because of the cut-out mentioned above.
Maybe the Uni just has a large batch of bad batteries? You should also check what apps you have running on it all the time, and how often you use bluetooth and wi-fi - these two REALLY drain the battery if you keep them on all the time... Also try MemMaid, this is great at cleaning up your notifications queue, which is where lots of apps leave old and obsolete entries clogging it up.
I have the same problem. I do not know where the charger is, so I am always using the USB while syncing. I also tried 2 batteries, but they both last about 12 - 14 hours. Maybe it is caused by WM6.
I did not quite get this solution:
"Soon sorted it when I found that the Jasjar had decided to disable the automatic switch off, now a charge is back to lasting 2-3 days.
Mike"
What is the solution?
2 421....:
sorry for lang. the above understands(i hope)
nastavenia(settings)/napajeni(power)/rozsireni(advanced) tam zaskrtnes co xces a nastavis casy. ak pouzivas phonealarm musis aj tam. pozri si aj podsvirtenie(backlight).
btw aj had the same prob. appeared after 6mnth. i bought new battery. btw here is several threads with same prob. try 2 look for solutions there(imho its only one-new batt.)
I feel like I'm walking on eggs...I bought my Jasjar used on eBay just over a year ago, still the original battery. I almost never use the 110v charger, always a USB conection with my Mac, often recharging at 55-75%. I just intentionally ran down my battery to 18% (got warnings to recharge), and recharge via USB/Mac again. It took me almost 4 days to get to 18%, and Bluetooth is constantly on for ready use with my earpiece.
Curious: are the problems with original or replacement batteries? Cheers,
Update to Radio 115 or 114
It's worth taking into consideration that when flashing, you really need to have a full battery. There are reports of batteries starting this kind of behaviour after user has flashed with drained battery, then causes battery charge issues until next reflash.
IMHO even if u charge with a full charged battery still u get a prob so i think its a common issue with the jasjar and its power managment software itself by default as lot of people with diffrent ROMs are complaining about it.
no changes...
well, folks, i tried all these gimmicks but not to any definite changes ... i guess i need to consult the service center guys at last...i didn't want to do that but i guess i need to. i'm sure it's not my battery as i've replaced 3 of them...i dont kno what else to do!!! thanks for ur posts tho as i get to try diff things to check if ma battery is doing ok...keep postin...thanks...
josh.
how 2 discharge a battery >>>>>
problem with battery?
I have the same problem, it firs appear on original battery when charge was 40-50% so I have bought the same battery model (1620mAh). But it doesn't help. Now I,m using the 3200mAh battery and it doesn't help as well. The thing is that XDA switch off it self always on deferent charge level (sometimes is on 20%, 45% ar 80%...so is very difficult predict when it happen again). And one more thing...when it switch-off and I try to switch-on back, I can't (keep switching off), only slolution is put on charger!!!
I have downloaded the service manual (I think called "confidential") and it mentioned that it could be a problem with main board (so its HW problem). So can anybody tell me is a problem with bat or MB? (replacing the MB is fcjfdj$#ing expansive). Thanx.
well if your XDA does not switch on until you start charging it that's a clear indication that your battery is empty. I have the same with my faulty battery. Replaced it by a working one and it's fixed. Something is definately messed up with the charging circuit or the batteries though. They are not supposed to die so easily.
SpyderTracks said:
It's worth taking into consideration that when flashing, you really need to have a full battery. There are reports of batteries starting this kind of behaviour after user has flashed with drained battery, then causes battery charge issues until next reflash.
Click to expand...
Click to collapse
The first time I flashed the PDA I ruined my battery. This time I thought I'd be smart and I put in the old battery while flashing. After flashing I put back the new battery and now that one is broken too! It wasn't even in the PDA when I flashed it. How bizarre is that?
I have to admit I did not fully charge that new battery before flashing, but I figured it would be safe since it wasn;t in while flashing. The battery worked fine the day before I flashed my phone (got the "charge now or save your work" message), but after the flashing and putting it in, it just crashes at around 30% or 40%. The usual battery misery.
Maybe I should try fully charging it and then flashing again. Trouble would be how to get it fully charged though. I always felt charging cuts off early on the "broken" batteries (pull the charge plug and stick it back and it charges for a while again).
I managed to restore my battery to good health by completely discharging it in bootloader mode.
First I completely charged it. When the led went green I pulled the shcarge cable and connected it back again. After doing this a few times it doesn't stay orange so long and then I stopped and left the cable disconnected.
I reset the phone (on full battery) and then I set the unit to boatloader and waited for it to completely discharge. I reset the phone again (on empty battery) and low and behold my trusty "charge now or lose data" warning came back.
BTW I reset the PDA hoping maybe it would store the power levels. I remember that trick from my Palm days where sometimes you had to reset a PDA on full battery to calibrate it.
I charged it back to full capacity and started using the phone as normal. When the battery was empty I got no crash but a friendly warning telling me my battery was going low. Phew.
Will try the same with my other troubled battery over the weekend.
I have the same Issue.But , I think it's about Rom.
and I'm try a lot of ROM version ,only one Version canbe use more than 3 day.
I can't find any reason ,.
discharge in bootloader ,I do it ,But battiery is same time for used.
Hi all:
i know i have been braging lately a lot on the forums about the battery issue after upgrade to wm6.
BUT- after actually surfing the net for like 2 weeks non stop, i found on several sites a solution which i think would end this "IF" someone has it.
Theoritical Explanation:
it's said that when upgrading to wm6 the battery has to be atleast 50% charged "this is wrong" .
battery has to be 100% charged because for example:
if your battery is say 60% and you upgraded to wm6, the new ROM will mark the 60% as your 100% battery hence why it drains so fast.
that's why you need to charge to 100% first before upgrade BUT the only way to make sure the battery is really at 100% is to remove it and charge it in the cradle separetly until the lid on cradle changes from amber to green.
after that put the battery in your BA and start the RE-upgrade if you are on wm6 already or Upgrade if you are on wm5 or wm2003SE.
you should notice the difference, i'm currently testing it for the 2nd time, to make sure it is the right solution.
P.S. am only a noob so excuse me for the unorganised post.
Pls someone test this aswell
Regards
The battery charge level has nothing to do with the OS, its part dependent.
If i get you right, what are you saying is "if the battery level is 60% on flashing, the new OS will take 60% as being the 100%(maximum) level of what the battery can go".
I think that's wrong.
DANDANA said:
The battery charge level has nothing to do with the OS, its part dependent.
If i get you right, what are you saying is "if the battery level is 60% on flashing, the new OS will take 60% as being the 100%(maximum) level of what the battery can go".
I think that's wrong.
Click to expand...
Click to collapse
yes, hence why the battery and BA gets to warm or hot while charging as it cannot exceed the 60% mark which is marked as 100%.
i think it's the only logical explanation
Any battery get warm or hot on charge (or one some type of charge, like car charge).
I may say b*** s***, but after upgrading to WM6, my battery is acting as in WM2003; some software (like HTC home) is draining more, but nothing isn't abnormal; i still get with a 2400 mA a normal day of BA use (PDA+phone).
DANDANA said:
Any battery get warm or hot on charge (or one some type of charge, like car charge).
I may say b*** s***, but after upgrading to WM6, my battery is acting as in WM2003; some software (like HTC home) is draining more, but nothing isn't abnormal; i still get with a 2400 mA a normal day of BA use (PDA+phone).
Click to expand...
Click to collapse
the ting is my battery was working very good before upgrade with wm5 and wm2003SE but after wm6 this happened, andnever had i get the battery and BA so very hot like ths.
i finished the re-upgrade after charging battery and it's draining is much better, dropped in 1.30 hours 50% but still getting much draining, it used to drain to zero in 1 hour
ahassouna said:
the ting is my battery was working very good before upgrade with wm5 and wm2003SE but after wm6 this happened, andnever had i get the battery and BA so very hot like ths.
i finished the re-upgrade after charging battery and it's draining is much better, dropped in 1.30 hours 50% but still getting much draining, it used to drain to zero in 1 hour
Click to expand...
Click to collapse
Did you disables infrared on the new install? This might take some extra power.
nothing wrong with the OS , i believe it's a psycho matter maybe ??? my battery was 94% charged .. i took the device and went on a trip .. 4 hours with TCMP on listening to Mp3s .. i went back home after 5 hours it was 53%. Sounds good for me. 1450mAh and i charge it every 2 days with normal consumption. Maybe ur batteries are getting old because with No plugins installed it's just as good as WM2003SE.
Battery status - Its possible
ahassouna might be onto something. Logically I know this sounds unlikely. However I recall exactly the same point occuring in the smartphone forums when an OS upgrade came about. It was common knowledge that for the HTC smartphone you should have you battery fully charged when doing it. It was widely tested in the forums - www.modaco.com and generally accepted back then that for best perfromance your battery should be 100% when upgrading. BTW - in my opinion this is the best ROM ever released for BA - big thanks and respect to Helmi!
if it's so you never come back after upgrading with non fully charged battery.
I think that's wrong.
Emm let's say u were right, so i assume that the OS wont determine the correct battery level. So logically, when u get a 0% , the battery is shown as empty while it is not. So if u think a bit , when the OS indicates that the battery is empty, it shouldnt turn itself off because in fact IT IS NOT. So if you get ur device to turn itself off without being able to power on again , that means that the OS was right and it was 0% for real. ( Correct me if i'm wrong )
as the Matter of fact, wm6 is slightly 'heavier' than wm2003, it contains more drivers and stuffs. so it will consume lot More resource than wm2003. I think battery draining also closely related to the read/writing speed of your sdcard, how big the capacity...
My SX66 drains equally under all three OS's, Though I must admit I quickly upgraded from WM2003SE to WM2005. Ran WM2005 for almost a full year, good battery drain, WM2006 seems to drain the same thus far
I would have a look at your battery, there cheap to replace on ebay and such.
Slide2Unlock
Do you use Slide2Unlock? I confirmed that the software was draining battery faster especially ver 1.216. I uninstalled it and my battery back to normal.
I hope it helps.
I don't believe that would cause any problems...the OS is independent of the battery. Anyway, my battery use is only slightly higher in WM6 than WM5.
Your battery can be at any level when you upgrade the ROM...I really cannot see how the OS would "read" the status of the battery and set that as the 100% level.
Try running your battery down to something below 50%, then reflash your ROM...now what does the battery meter show? I bet it shows the same as before you flashed it, below 50%.
blues01 said:
Do you use Slide2Unlock? I confirmed that the software was draining battery faster especially ver 1.216. I uninstalled it and my battery back to normal.
I hope it helps.
Click to expand...
Click to collapse
i double that
the_scotsman said:
I don't believe that would cause any problems...the OS is independent of the battery. Anyway, my battery use is only slightly higher in WM6 than WM5.
Your battery can be at any level when you upgrade the ROM...I really cannot see how the OS would "read" the status of the battery and set that as the 100% level.
Try running your battery down to something below 50%, then reflash your ROM...now what does the battery meter show? I bet it shows the same as before you flashed it, below 50%.
Click to expand...
Click to collapse
Yes. In fact every battery has a internal chip for charge controll and status level. OS reads the status of the battery by this chip.
blues01 said:
Do you use Slide2Unlock? I confirmed that the software was draining battery faster especially ver 1.216. I uninstalled it and my battery back to normal.
I hope it helps.
Click to expand...
Click to collapse
no i don't use it, i finished flashing for the 3rd time with a "3rd battery" Still same problem BUT draiing is less than before but still 1-2 hours max without any calls and drops to zero.
am begining to think my BA went razy for some reason.
P.S. i have no apps or anything installed other than flashing the ROM.
My BA drains normally. I have 2-4 days of standby with occasional calls and usage. The backlight auto-closes in 30 seconds, the power goes off in 1 minute.
ahassouna said:
no i don't use it, i finished flashing for the 3rd time with a "3rd battery" Still same problem BUT draiing is less than before but still 1-2 hours max without any calls and drops to zero.
am begining to think my BA went razy for some reason.
P.S. i have no apps or anything installed other than flashing the ROM.
Click to expand...
Click to collapse
Can u retest it on a WM2003SE ? i think maybe a short circuit with ur device or whatsoever
ramdacBlueAngel said:
Yes. In fact every battery has a internal chip for charge controll and status level. OS reads the status of the battery by this chip.
Click to expand...
Click to collapse
Exactly...so the first post is wrong...the OS reads the status of the battery and it doesn't matter what charge status the battery is at when you reflash...the battery status circuit will show the proper charge percentage...
i've read about similar topics, but i think i did not found answers...
i've been aware that x2's battery drains fast. i had lots of bad experience with this problem so i decided to buy a new spare battery. to describe my problem, here is the scenario.
1. i fully charge my new battery
2. i remove my new battery to charge my old battery
3. after my old battery is full, i remove it to use my new battery (which was fully charged 4 hours ago)
4. after turning on the phone, it reports (immediately) BATTERY IS LOW.
5. i scratch my head why, replace it with the old battery instead, turn it on, and reports LOW BATTERY also.
i think this is a phone problem and not a battery problem. what do you think? why do i also encounter same problem with my brand new battery?
please help. thank you...
this is a new problem i encountered after reformatting my phone...
did u try flash to another firmware?
I had similiar problem as u when was using firmware Genenic_sg, flashed to Generic_en then its gone
by trial and error...
by trial and error, i found the solution... (once my main battery runs out of life, i do this steps...)
i let my spare battery stay on the phone for about 10 seconds before turning it on... (something like at least, the phone will recognize the life of the newly inserted battery)...
there are occasional times however, when the battery meter will still say low battery life even if i already had the battery stay before turning it on... so what i do is just turn it off again, remove the battery for few seconds, reinsert it immediatelt, and turn my phone again... and voila! it's finally recognized as 100%.
Hi all,
Basically a few days ago I updated the firmware via Kies from 2.2 to 2.2.1 on my Galaxy S. However, I instantly noticed a huge decrease in battery life - 50% gone overnight when in standby! So I factory reset the phone and had everything disabled - the phone only lost 10% in 24 hours. So I decided to try and eliminate the possible causes so first I turned on wifi and within 2 hours I have lost almost 30% of the battery life with no usage so wifi seems to be the culprit
In the wifi menu network notification is off, however, the device seems to be scanning for networks every 5-10 seconds even when connected! I had no problems like this on 2.2 where I could comfortably get 2 days usage with wifi on. Also as I would prefer wifi to be on constantly when connected I would prefer not to change the wifi sleep policy. Any suggestions would be much appreciated
Many thanks, and sorry if there's similar thread already
which version of 2.2 did you have before?
try a flash back and see what happens.
Or try to drain battery (do not charge till 1% or almost dead) then full charge it.
Always happen to me when I flash my phone to a new ROM.
Thanks for the replies. I've tried leaving the battery till it was almost drained but maybe I'll let it go completely flat and charge it see if that makes a difference?
Also trying juice defender from the market to see if that helps. Not sure if it is a problem with the firmware though been looking around and a few people seem to have had the problem with no real solution
Might have to go back to 2.2 but would prefer not to as I've noticed a big decrease in lag on 2.2.1. Also can't remember what version of 2.2 I had I'll see how the battery life goes over the next few days after trying a couple of drain/charging cycles hopefully won't have to downgrade it. Come on 2.3.2
Thanks for the replies so far
Battery Bug is Major issue with all the versions of 2.2.1, Battery life is very bad. Even the Browser is worst in 2.2.1. May be in 2.3 it will get fixed.
I have tested all the new releases of 2.2.1. I found its smooth and fast.
A1exM said:
... replies. I've tried leaving the battery till it was almost drained but maybe I'll let it go completely flat and charge it see if that makes a difference?
...
Click to expand...
Click to collapse
Very very bad idea to let the battery go completly flat, it's the best way to damage it and even lose 20% of his initial capacity. Never go under 10%.
To calibrate it properly, wait 10% turn off the phone, fully charge it, restart. (do it again 3 times).
ttf said:
Very very bad idea to let the battery go completly flat, it's the best way to damage it and even lose 20% of his initial capacity. Never go under 10%.
To calibrate it properly, wait 10% turn off the phone, fully charge it, restart. (do it again 3 times).
Click to expand...
Click to collapse
The battery is calibrated to do this already, the charging circuit will not allow power to the device unless there is a certain amount of charge in the battery. It's there to protect the battery from this exact eventuality.
bullzeye.za said:
The battery is calibrated to do this already, the charging circuit will not allow power to the device unless there is a certain amount of charge in the battery. It's there to protect the battery from this exact eventuality.
Click to expand...
Click to collapse
That's how it's supposed to be in an ideal world.
I flashed original rom but my battery behavior is still like on 2.3.5 RC4. Charge to 99% and drains very fast. Did someone know how to get back it original life. I tried battery calibrators from the market and battery wipe from clockwork mod but no result
If your optimus is old it is normal that battery life will get worser and worser ... All you can do is get new battery of ebay like I did and now my battery life is normal ...
Mike
It's not old. Its younger than a year. Battery life was good and on swift it last long and charge to 100% but after last time i flashed 2.3.5 rc4 i calibrate it (to try it last longer like on other roms) and now even on stock it drains like on rc4 and not charged to 100%
Use spare parts to see is there app that drain battery.
install "batterycalibration" from market, charge to 100% and calibrate your battery for this rom
Yes i download two battery calibration programs but the problem is that it's not charging to 100% but to 99% and drains very fast after this. i'll calibrate it a few days hope to fix
yeah, that happens to most people.
unplug, use a few seconds or 1min or so and plugin and wait if its fully charged, it could be that you have to do that a few times (2-3x)
coleonyx said:
I flashed original rom but my battery behavior is still like on 2.3.5 RC4. Charge to 99% and drains very fast.
Click to expand...
Click to collapse
Your not alone on this, same thing with me.
I have ordered another battery from ebay but dont really know why all of a sudden this just began happening whilst using the same Rom which I think has something to do with it.
I use a program from Market called Android Booster to terminate running programs that start up or dont close once started, as sometimes if you use your camera, it will be still running, even if you close it up so hence battery life turns crap.
But also, if somebody phones me for 5 minutes this also nearly drains my battery, and I have everything also turned off. (WLAN, Blutooth, Data, GPS etc).
So dont know why this is suddenly heavy on the battery as it never seemed to do this when first installed.
There you have it, your not alone but think I will migrate to another or buy another phone as I think its pathetic to have to charge one's phone everyday, or twice a day if you chat to somebody for 5 minutes as it defeats the purpose.
coleonyx said:
Yes i download two battery calibration programs but the problem is that it's not charging to 100% but to 99% and drains very fast after this. i'll calibrate it a few days hope to fix
Click to expand...
Click to collapse
Try charging through the wall charger instead of through the USB port on your pc. Worked for me then, recalibrate.
Turning off 3G when not needed?
Try turning 2G Network only in Wireless and Network --> Mobile Network
airbus360 said:
Try turning 2G Network only in Wireless and Network --> Mobile Network
Click to expand...
Click to collapse
I got my brand new battery and even charged it up via Power Supply from the wall.
Have run the phone only on 2G network only box ticked and everything else turned off (and I mean nearly everything) and for whatever reason, the Battery new or old still does not last long.
Even after it charges to 99% says its charged, it discharges very fast, or if somebody phones you and you only talk for 2 minutes the battery drops to like near 30% which is pathetic.
Something is sucking the life out of the battery folks with these Rom's so can somebody exactly put the food on the table here and say, whats up?
zzsomebody said:
I got my brand new battery and even charged it up via Power Supply from the wall.
Have run the phone only on 2G network only box ticked and everything else turned off (and I mean nearly everything) and for whatever reason, the Battery new or old still does not last long.
Even after it charges to 99% says its charged, it discharges very fast, or if somebody phones you and you only talk for 2 minutes the battery drops to like near 30% which is pathetic.
Something is sucking the life out of the battery folks with these Rom's so can somebody exactly put the food on the table here and say, whats up?
Click to expand...
Click to collapse
What ROM are you using? It takes some time to charge up the battery and even if it says '99%' that doesn't always mean that it is. What is the capacity of the battery? I'd say charge it for about 6 hours and see then.
Thanks Johnny,
Problem at present seems to be solved now.
Yesterday and before I had been using Mur4ik's CM7 2.0 RC4.
I then uninstalled a stack of apps that I only used every so often and now its like back to normal so I guess it must have been those apps installed.
Folks here is a big tip. Uninstall Apps to test your battery to find out which one is the Energy Hog because even if you are not using them, they seem to be running due to either bad programming of the app or a system management issue related connection between the two.
Now, I have just updated to Mur4ik's CM7 2.0 RC5 and will certainly think twice prior to installing a bunch of things for the sake of installing apps.
Cheers people~!