hi all i am new here
i recently bought my self a new motorola h500 bluetooth headset, the problem is when i connect to my kjam the voice sounds cracking and is not pleasent, though all features work and i dont think there is any problem with the headset, as it works just fine with my p910i, se k750i and my sharp gx 15
. so i was wondering is the sound transmission quality of kjam bad or is there something worng with my kjam or the headset,
please reply as both of them are still under 14days return policy so i can change if any one of them is not right
pls help
cheers
I do not have the same headset (jabra bt 190 I believe), but I find the sound of the headset very distorted. So maybe it is a rom problem? It could also mean that the devices are just not compatible, I did not have this problem on the Qtek s110, there it sounded great.
Make sure nothing is running
I find that my bluetooth headset crackles when I have a lot of programs running in memory. Go to Settings->Device->Memory and select running programs and close all and see if you get the same result with your headset.
Related
go to hklm\software\oem\voicecommand and set the value of "launchapenable" from 1 to 0
when activating voicedial from your headset (press connect button at the headset 2 sec.) it diverts all audio to the bluetooth.
works also with musik.
pressing the button again it disconnects the bluetooth and the main speakers are active again.
in this case the original voice dial does not work anymore until you change the value back to 1.
for me a good solution because i don't use voice dial and prefer insted skype and headset.
Very good tip...will try that!
Cheers...!
Works on QTEK S100 with Jabra Bt 250 Headsets?
Do you happen to know if the BT specification of the EXEC allows it to transmit stereo audio? Say from a mediaplayer to a BT car kit?
If so, that would send me over the edge and Id have to buy a BT carkit!
...ohh, on 2nd thoughts, it would also depend on the bandwidth too. Anyone know what sort of frequency range BT stereo may be limited to?
for stereo output is another reg.hack needed i think. because pushing the voicedial button at the handset it activates the bluetooth headset profile for listening to the voice but voicedial doesnt start. so you can use it for normal micro and loudspeaker.
maybe anybody knows how to activate in this case the "high quality audio profile" by editing the registry instead of "headset profile"?
Great job, The sound (in music) is good ? i tested this but the sound wasnt good.... I think my headset isnt good for music.
yes it depends on the bluetooth profile. for good quality "high quality audio" (A2DP) profile is needed.
blueangel
would this work on a blueangel running WM5?
gazela00 said:
Works on QTEK S100 with Jabra Bt 250 Headsets?
Click to expand...
Click to collapse
How did u do it....I mean yours is not a WM 5 OS...Pls advice
hdubli said:
gazela00 said:
Works on QTEK S100 with Jabra Bt 250 Headsets?
Click to expand...
Click to collapse
How did u do it....I mean yours is not a WM 5 OS...Pls advice
Click to expand...
Click to collapse
No it does not work in QTEK s100....
Works -but not great
very tinny muffled sound on my moto HT 820, was hoping it would work as well as the bluetooth stack update for the magician.
Sound does come out in both ears on my stereo phones. but I dont desire to listern to the tinny sound.
Still great find and discovery. Just hope someone can progress it to A2DP asap.
sorry, but can anybody tell me how to edit the registry in WM5? I never did it before. What tool do you guys use? Is it something free?
Thanks.
I used PHMREGedit
Here's the link:
http://www.freewareppc.com/utilities/phmregistryeditor.shtml
andyes....it's free.
Tried it with my BT200
I know the registry works....but cannot get it to play on the headset.
It works...becos upon pressing the phone button on the head set for 2 sec, the audio comes from the handset. On redoing it again, the audio goes off from the handset.
Mine is working fine. I really like the way its now.
Thanks a lot.
Ooops....
my Bt200 wasn't working. That's why there was no audio coming from it.
Need to figure out why there is no audio coming from the headset.
Sigh another problem!
So basically, the registry works.
Im using Total Voice COmmander and it works with WMP.. No need to install another software to play music thru BT.
I just press my Jabra headset twice and it goes "Say Command".. then I say "Play a music"..
Sometimes it's stubborn and Calls someone or Says "Today you have no Appointment" but I guess with a lot of practice, my Dopod understood what Im saying and played me a song.. Now, Im having trouble with my Dopod catching the title of the song i want it to play. I've placed voice tags on the songs and 50% of the time, my dopod got it right.. got to work on the other 50% though..
Sorry if you have already read this but I am still having a problem!!
I got the new Bluetake iphone mini stereo headphones for christmas and was hoping to use them with my MDA Pro (running the new O2 ROM).
I have them paired as a "Hands Free" device...
I know that I can't use the stereo features until the new A2DP patch come out (hopefully soon!), however what I want to be able to do is use voice command to initiate calls etc. However when I press the call/power or Play/Pause button all I hear is a beep from the headset and nothing hapens on the PDA...
However I can use the button to answer and hangup a call (as long as I answered it with the handset...) If I initiate the call on the MDA then I can't hangup with the headset...
Am I doing something wrong or does it sound like something is faulty??
Any advice?
Thanks
Andy.
I actually had an oportunity to try out the voice levels and sound is awful! I also tried to connect it to my SE T610 and it refused and it did the same when I tried to connect it to my Toshiba M200 tablet PC as in both cases it never asked for the passkey...
I am begining to think that they must be faulty??
But becuase I have never had a BT headset before so I'm not sure if I am doing something stupid!
Andy
I have managed to try a SE BT headset with my MDA Pro and it did work and activate voice command. So it would seem that the headset is faulty. Does anyone have any ideas before I send it back?
Andy
Please!! Is there anyone here who can comment on whether they think these are broken or if I am just incompetent!
If they are broken then I need to send them back really soon...
FWIW, my Jabra BT330 and the SE HBH-662 just need a single quick click to activate the voice dial, but these Plantronics Pulsar 590A things I just got (which are fandabidosi by the way!) need a prolonged press to do the same.
Have you tried keeping your finger on the button for a while?
Ferg.
andykemp said:
Sorry if you have already read this but I am still having a problem!!
I got the new Bluetake iphone mini stereo headphones for christmas and was hoping to use them with my MDA Pro (running the new O2 ROM).
I have them paired as a "Hands Free" device...
I know that I can't use the stereo features until the new A2DP patch come out (hopefully soon!), however what I want to be able to do is use voice command to initiate calls etc. However when I press the call/power or Play/Pause button all I hear is a beep from the headset and nothing hapens on the PDA...
However I can use the button to answer and hangup a call (as long as I answered it with the handset...) If I initiate the call on the MDA then I can't hangup with the headset...
Am I doing something wrong or does it sound like something is faulty??
Any advice?
Thanks
Andy.
Click to expand...
Click to collapse
Just looked at the instructions for the bluetake i-phone (bt450rx),
(got them myself for xmas)
and it does not say that you can connect to the phone for voice control,
however you should be able to hang up from the headset.
i have got the k-jam (wizard) and can dial from the k-jam and hangup from the headset.
voice control may not be available because the new bluetooth stereo headset's are ready for AVRCP (Audio Video Remote Control Profile).
the older bluetake headset bt420rx can be used for voice control but do not have AVRCP function.
I hope i am wrong, but it may be the answer you have not been looking for.
Hmm... That sounds bad...
I only have a few days left to return it and don't know whether to get a replacement or to go for a different headset?
i like the idea of being able to play/pause/f-foward/rewind via the headset(when bt v2 upgrade is available), because music playback is more important to me than voice dial.
of course if you can send it back, then perhaps just wait until bt v2 is available, and then buy a headset for the uses you require it for.(wish there was an emotion with cross eyes) LOL
I know what you mean but I would still be able to use voice command!!
Does anyone else have the 450Rx and a universal and could test it for me?
if you do prove me wrong (and i hope you do) please let me know.
answering this problem further,
the bluetake i-phono mini headset cannot be used for voice command,
however the motorola ht820 can be used for voice control.
Had similar issues with my headset (not the same type). In the end, I had enable secure mode on the universal, pair the devices, select serial port and then immediately initiate the voice dial, otherwise it didn't work.
Gareth
I decided to play it safe and returned it back to Expansys for a refund. When someone else gets a set of stereo headphones and A2DP is out... and crucially they can confirm it works! Then I'll buy a new one!
Cheers
Andy
one good thing with motorola ht820 is that they can be used with a detatchable cable, so whilst i'm using them bluetooth for the phone side, i can still hear good quality music.
also i know from trying them with my wife's qtek s110 that you can control windows media player as well.
you may have already tried this, but just in case you haven't,
install and run the three files for either "bt off", "bt on", or "bt toggle",
this will switch all audio to the bt headset or away,
of course quality is not good, but at least no cables.
ps. if the headset is switch off and you put bt on, you will get an on screen error message.
aliendad said:
one good thing with motorola ht820 is that they can be used with a detatchable cable, so whilst i'm using them bluetooth for the phone side, i can still hear good quality music.
also i know from trying them with my wife's qtek s110 that you can control windows media player as well.
Click to expand...
Click to collapse
Do they come with this cable as standard?
EDIT: Did a search, and they do.... might just buy them now and sell my Sony EX-71's.... would they we at least the same in terms of sound quality? It's the thing people talk about least with these devices!
So lemme see if I got this right.... even before I get A2DP installed on my Exec, I can listen to perfect music using the cable, and also use the hphones as a bluetooth headset as well? Will the music still pause etc when a call comes in?
Just bought a pair of HT820's on Ebay there.... £38, not too bad. Should get about £25-30 for two pairs of existing headphones, so well please.
Greetings,
I'm using a Sony Ericsson HBH-DS970 stereo Bluetooth headset with my TyTN and so far I have only one gripe - when the headset is connected, the ring tone somes through the handset only, not the phone itself, which means that I'll miss any incoming calls if I don't have the earbuds inserted.
Also, the ring tone sometimes does not start until about 20 seconds after the display has started to announce the incoming call.
I tend to have the earbuds hanging from my neck if I'm not listening to music, and the ring tone is not loud enough to be heard that way.
I suspect this may be by design, because it's assumed that a stereo Bluetooth headset is always in/on the ears when connected to the phone, but I want to use the 970 as my only headset even when I'm not about to listen to music.
Is there any way to get a ring tone from both headset and phone?
/POL
?
Anyone figure this one out yet? I have the same problem...
same here, anyone find a solution please post, I think I can change it from the registry I will check it.
Can I ask you folks a question relating to the use of the headset Sony Ericsson HBH-DS970 with the HTC Hermes...do you get all the functionality ie caller ID, the ability to accept and reject the call, compatible with mediaplayer etc.
I have a concern that with the headset not being a HTC product, perhaps some of the Sony functionality may not work with the handset.
Thx
From my experience the ringtones will not come to the speaker if you use the headset as wireless stereo. I only use the headset as handsfree, which makes the ringtones go through the phone.
I used the DS970 for two week with my O2 Trion,feature like Caller Display is No any problem,But when using media player sometime it may out of control, like cann't accept call and control volume or stop.
And the sound quality is acceptable,but it will stop few second after 1 or minutes, I have change the regedit.
May I know is there any way to fix it?
Still no solution?
Anyone come up with a solution to this problem? It really bugs me not to get a ringtone from the unit itself, just thru headset... Works just fine with my old mono handsfree, would be great to have it in the stereo heaseat to...
i have the same problem
hello i have the same problem
the ring sound is only on my headset i have tested with 1.13.097fr and now 1.13.234fr if anybody have the ring on the phone with a headset stereo a2dp cang give us is configuration rom and other soft for the bluetooth.
thank and sorry for my english
juste a little frenchy
There seams as if there's no solution in sight, I got the exact same problem, also with HBH-DS970 and with Jetware Mobile's "Hands-free extension" installed.
I'm still running WM5, anyone who have tried WM6?
/Fluff
Same "design feature" here with my HBH-DS970 and HTC S710 WM6 Smartphone, so it's not ROM, device or OS version specific. I would suggest this is by design.
I'm pretty sure this is by design since thats how it works on my BT8010. Its stereo so it seems to make sense all sounds go through headset although it would be nice if it was an option. The BT8010 has a button on the headset to take it out of music mode so then they will go through the phone but I guess that doesn't help any of you out much.
Another option would be to just uncheck wireless stereo in the pairing and just check it back when you want to do wirelss stereo.
I m so disappointed!
I hone a SPV C500 since 2 years, last week I bought a stereo Bluetooth Headset Samsung SBH 100.
I succeed to connect my bluetooth devices with my phone, it’s working why the voice.
But to play the Mp3 on my headset, I installed Bt AudioToggle, and now I have a very very bad sound on my headset.
Is it possible to upgrade something or do I need to change my mobile ?
Please help me!
Thanks
Capjulio
Bt AudioToggle is a hack that sends all audio to bluetooth the same thing happen to my HTC wizard when using this but when using the A2DP profile the sound is great. I dont think they have A2DP for WM2003 SE but if you get it to WM5 maybe there is a chance you can get it to work.
Can u post Bt AudioToggle or a link i can seem to find it for smartphone.
Hi,
i bought a Samsung SBH100 BT headset, works fine with my Asus P535, but on the headset just only volume buttons working FF and play/stop don't do anything. I use CorePlayer (TCMP) on the PDA.
What I do wrong?
Please help!
THX
U can try change the regedit
[HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\A2DP\Settings]
"MaxSupportedBitPool"=dword:78
"BitPool"=dword:40
"UseJointStereo"=dword:0
"Samplerate"=dword:48000
"BitPool"=dword:40
Hi Everybody,
I am using the X01HT which running with
Rom : 2.05.255.1
Radio Ver. 1.34.00.10
The problem is my friend said that my speech sound very poor (the background sound very strong )
when my phone is connected with the BT Handfree.
Just wanna know how the chase the problem is from my handfree or my phone.
furthermore, Is it possible to check my handfree is running real A2DP (Stereo sound )
my Handfree info: http://www.itechdynamic.com/en/products_spec.asp?cid=2&pid=02050
sorry for my poor english
Your english is fine
This not an area I know much about but the following may be of use:
http://forum.xda-developers.com/showthread.php?p=1152585&highlight=sound+quality#post1152585
HtweakC Link
http://www.fit4cat.de/thread.php?threadid=263
Try using search as there are several posts on this kind of problem.
Mike
You can check A2DP by playing a song that is in stereo. Anything with an obvious sound in the right channel will do, as if A2DP is not working it will only be playing in mono.
Also, the little icon in the taksbar will show a headset with a music note inside of it if A2DP is working.
The sound problems you mention are probably due to the quality of the headset. Try it on another phone or try a different headset on your phone.
I am using the same ROM and radio and my BT works great. (AKU 3.3)
I use both the Nokia HS-12W and a HTC BHS 100.
A2DP will give true stereo in WMP10. Strange I found the Registry still set to mono, so I had to change that for stereo.
The call quality both incomming and outgoing is great with these headsets as well.
The HTC also allows you to use your favourite earphones as well.(3.5mm jack)
Hope this assists.
Thanks
Thanks all first.
Yesterday, I did some stupid test about the voice quality,
I used the recording function in Note to record my own sound near the TV in my home, and found it was not bad.
However, then I went out use the BT headset again, but my friend said, dont use it again, my sound really poor
After that, I bought a BT dongle to try to test my BT headwith in my computer, but the Dongle comes with the bad BT management Driver, called XTNDCoonect Blue Manager.
Do you all have the widcomm software and send it to me ?
I dont know it is against the policy in the forum.