Database Users

sx56-wm2003-upgrading - no boot - unit dead. need help

I was upgrading using sd card and took out the card while upgrading and the machiine does not boot. I treid soft reset, hard reset, took the battery out, and reset it.
No luck.
Any time I do a hard reset - i can see the red light blink. It charges fine.
Any help please

Why did you remove the SD-Card while your upgrade was running? :?:
I think this was avery bad idea.
If you aren´t able to get into the bootloader and reflash your device again, you have won a high quality paperweight....
I´m sorry, but i think there is no usable solution to realive your device....
Stefan

Need Help!!!!! Uni semi-Dead.

Hi All,
I had this device for few months now after selling off my Eten X500.
The Universal was a big device but I truly loved the XGA big screen. And yesterday disaster struck. Normally sometimes the device would go haywire but a few soft resets or hardreset would set it back on course. But yesterday it refused to move on from the bootloader mode and when I used Buzz utility prgram, it did move away from the bootloader but didn't swith on anyway. And yes, I have flashed the ROM's quite a few times and I managed to flash it with T-Mobile's latest WM5 ROM today morning. The flash was successful but it just wont work normally.
I have 2 batteries but bith yieled the same result. I could only get it to switch on if I hardreset it on a table with 2 fingers firmly pusing the soft keys down. It would sometimes would boot but would hand after it fully loaded. I have removed the SD card as well as the SIM card. Not sure if the devie motherboard is having any issues or some connection problem. One thing for sure if I hold both edges of the device and press it hard and try a soft reset, it would boot sometimes. I even have the external battery charger and I can charger the batteries full.
Any idea how much would it cost (I'm in Singapore) for a repair or anyone who could help me with this.
The worst thing is, this is my only phone and I really need it to work asap.
Hope someone could shed some light on this.
Thank you all in advance.
Techx

Have a look at the wiki...
I had the same problem after I put it on charge with no battery in - very smart I know . It explains about using MTTY and how you format the DOC which should solve your problem - hopefully...

Hi all,
I tried the MTTY utility but I can format the DOC files. everytime I try to format it, I get an error like this :-
USB>set 14 0
HTCSF kEØ(HTCEUSB>task 28 55aa
Wait..
flFormatPhysicalDrive:status=20
Read data error in tag
DOC_format failed!
USB>
So anyone can help in this issue plssssssssssssssss
Thank you all.
Techx

anyone????
Anyone? pls help!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Do h3lp!!!!!!!!!!!!!!!!!!!!!!!
Anyway of getting the unit fixed? Anyone from Singapore can recommend a shop or anything?

MDA Froze and doesn't afer that

I am sorry if this issue has already been address, and will be glad if someone can point me to the right forum and any solution will be appreciated.
I installed few games on my MDA (the were intalled to the sd card), I was playing a scrabble game when the device froze, I did a soft reset on the device and the device hasn't loaded up since then.
Device Info
IPL is 2.26, SPL 2.26, GSM 02.25.11, OS 2.26.10.2.
When the device is powered on, it loads the boot screen and gives me all the above information but doen't do anything else.
When the device is on the ac charger, you see the orange light.
I am not sure if I can reinstall the OS on the device or if this is a hardware issue, also if someone have the original ROM, or a link to a ROM for tmobile MDA (US) that I can place on a SD card to reinstall, please post.
Thanks

Just take out the sdcard and soft reset the phone,hope it'll work,otherwise,do a Hard Reset,but mind it that,by doing Hard Reset you'll lose all your personal data,but your phone will start to work.
Perhaps your sdcard needs to format.

my Qtek 9000 just went dead and wont turn on!!

I upgraded my uni with ranju rom 2months ago and worked perfect.Yesterday after a call the uni froze when i restarted, the uni black out. have tried both hard and soft reset. Nothing happens in soft reset, but hard gives U " Press 0 to restore to factory default and X to exit". but if i press 0, the uni goes off again.,

Battery? Can you enter a bootloader and re-flash the ROM?

I can't get pass "Press 0 to restore to factory default -Press X to exit" screen

i also have same problem with you. and i have connect my device to PC usb cable, then PC detect my universal but cant recognize it as pocket pc.
please anyone help us.....

hello
hi all, and thanks in advance for reading this thread.
my cousin gave me his qtek 9000 saying that it was dead. being a dumbass, me decided to try and give it back life. as mentioned before, me a dumbass. After seaching the web for hours, i would normally be now saying, i give up. but no.
so , please. help.
the only thing i can tell u is that when i plug it in the pc, a red light starts bleeping. Won't turn on, soft and hard reset do not seem to make any effect, nor the power+light button.
again, please, help.

Had exactly the same...my qtek 9000 was just lying in the closet for a long time and would not boot anymore...
When I used it last time al was fine. I figured a dead battery so bought a new one...
It would give me the red LED while charging, would not be recognised on the computer etc.
Did a hard reset and then got it into the bootloader...
Had to run my laptop on XP as under Win7 it would fail to flash or do anything, but under XP it flashed properly.
After flash installed my back-up and all seems to be running fine now!
May be it helps anybody...

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone

Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!

Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...

hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards

That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...

I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.