Related
If i want to upgrade my wallaby i get an error message in the communications procedure. I have downloaded my ROM from lumpy's kitchen and ive tried to upgrade it many times right now.
Can anyone give me an advise how i could hardflash the ROM of my device?
I think you get an communication error when trying to flash via ActiveSync.
You have to flash via bootloader....
http://wiki.xda-developers.com/index.php?pagename=Wallaby
Here you get furthe rinformation about how to do it....
HTH
Stefan
Nothing yet
Ive tried to Bootload te rom, but after the message "connect your USB now" the device does not react anymore.
I have tried to run the application rom but this says that active sync does not recognize a device.
What should i do next?
Thanks for the quick respond!!
Even if i make a bacup to SD this doesnt work. There no explaination how to hard flash the device! Can you give me an advise???
What have you done exatcly, and where is the problem?
It's not really clear for me.
For Flashing via SD-Card there is no USB connection necessary....
STefan
I have tried to flash with the bootloader. When i push on the on/off putton and do soft reset i see the question "connect to USB now". If i connect and i start the rom nothing happens.
Afterwards i have tried to put the rom on my SD card. I have tried to do this OSimagetools. The pc does recognize the SD card in my wallaby. I also dont have a cardreader.
Is there a way to flash my wallaby in the bootloader-mode with the USB connection?
What do i have to do for it?
Thanks
Strange.
You should see device displays a background that consists of four equally sized vertical bars, colored (from top to bottom) white, red, green and blue. On top of this, it says:
WALLABY
Bootloader
V5.14
WAIT
After a few seconds, the WAIT is replaced by GSM OK. Both messages are in the blue bar, but have a white background.
What do you get?
What is labeld on your rear sticker of the device? (modell) ?
Stefan
Its model: PW10A1
SN: HT220cc15300
PN: 99HJ00007-00
Step 1)I have seen the horizontal bars. And its version 5.18. Ive also seen the "GSM OK"- notification.
Step1a)If i connect it afterwards to my USB nothing happens. The computer does not recognize the Wallaby.
Step2) If i hold the On/Off button i get the message "Connect to USB now" If i do this, activesync does recognize my device and i cannot install the ROM.
Step3) after step 1 i press the contacts button and i see 6 ways to backup my rom or GSM. I have backedup my GSM and ROM to SD. But this has no use for me.
Greetz,
Ok. Now I see.....
First of all, you have an totaly unknown Bootloader (5.18) to me, so i hope all steps will work....
You require a SD-Card with >= 64 MB
XDATools ftp://[email protected]/Wallaby/Tools/XDATools.zip
Your downloaded ROM from my kitchen
step1) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step2) Copy all your data of your sd-Card to your local PC otherwise all data on it will be gone
step3) Enter bootloader of your device by pressing On/Off and doing a softreset
step4) After the Message GSM OK press the Contact Button of your device
step5) Navigate with the pad to "CE+BOOT TO SD"
step6) Confirm this with the Action Key (Press the middle of the Navigate-Pad)
step7) After finishing enter again bootloader by holding On/Off and doing a soft reset
step8) Bootloader should tell you something tah OS is detected on your SD-Card
If No -> Problem
If Yes -> continue
step9) Boot your XDA up normal and connect via active sync (guest partnership is ok)
step10) Install XDATools on your PC
step11) in a dos -box (cmd) go to the directoy where osimagetool is located
step12) enter command: "osimagetool -r xdasdslot -w original.nbf"
step13) enter command: "osimagetool --register"
step14) extract the downloaded ROM using winzip
step15) Run osimagetool
step16) Select the nbf-file in the english-folder of the extracted lROM as source and XDASlot as destination
step17) After finishing enter again bootloader by holding On/Off and doing a soft reset
step18) Bootloader should tell you something tah OS is detected on your SD-Card
step19) Press Action Key to install the ROM
step20) After finishing do a hard reset
step21) Now your ROM should be installed on your device.
step22) Locate the created file original.nbf and compress it using winzip
step23) Upload the compressed file to ftp://xdaupload:[email protected]/Wallaby/Uploads
step24) Enjoy your new ROM
That should be alll .....
;-)
HTH
Stefan
Thanks, But when i extract the rom to a folder, OS Imagetools cannot find the nbf-file. There is no nbf-file in the extracter-rom-folder. I can only find an nb-file.
There is a file called "NK" which says that its an NBF-file(properties). The file is 32MB large. I have tried to select this file (step 16), but the file is not being recognized. Even if i change the extension of the filename. The OSimage does not support this file.
I Have tried this with 3 ROM's : 2003 SE, 2003 and 2002 neither of them contain the nbf-file in the english folder.
Do you have an advice? I think i am very close right now!!
Thanks,
I have sucseeded to install 2002, but 2003 SE wont be recognized. It says its an usupported file.
Has this anyting to do with the fact that i renamed the file? If so can you tell me how to change the file back??
I have downgraded my wallaby to PPC 2002 right now.
Thanks Lumpi!!
WM2003SE couls only be installed via Exe-File. It can not be flashed with the osimagetool.
Stefan
Dear all
I try to update my PPC 6600 from WM2003 2nd edition to WM6. I download and run WM6 OS 5.2.2000 (Build 20000.1.0.0.PV.HAT). After I try to finish the last step of the installation which is to cool reset the PPC, there are 4 color bands and only show "NO GSM", "D 5.70.11 WWE". I try to turn it off, but doesn't work. I try to connect back to PC, but PC can not find this device
Please help
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
imatrix said:
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
Click to expand...
Click to collapse
I have tried, but not work, no format, no reset, stay the same
here is the message from the program. please help
USB>
USB>set 14 0
HTCST ÚÈHTCEUSB>set 14 0
HTCST ÚÈHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=EA0000
All:dwSize=1F20000
USB>task 0
USB>
I am very sorry, but I need help.
I am unable to fix this.
I am trying my best to follow the instructions and dont know where am i going wrong.
Like U said,
I went again with the Multi Port TTY utility and in the new USB text file window, ((stopped the wcescomm.exe application from taskbar)
I tried entering
set 14 0
USB>task 28
USB>task 0
USB>
Saved the file as USB
The phone in the cradle was still showing USB v1.02
I took the phone out of the cradle, removed the battery and inserted it back into the cradle
and i again starts showing USB v1.02
Where am i going wrong..
I also tried
USB>set 14 0
USB>task 28
USB>task 0
USB>
but in vain...
Please help in resolving this
I found http://forum.xda-developers.com/archive/index.php/t-273871.html online and the problem is almost identical as mine. Please help
i think u can flash it again
woi700 said:
i think u can flash it again
Click to expand...
Click to collapse
What do you mean flash it again?
It can not be detected by activesync
cables
Something like that happened to me a while back where i couldnt connect. The problem wasnt the BA but was the cable connections- usb cable connections. It stills happens today where i get a bad connection and i have to play around with the usb that is plugged into my laptop. Maybe you should check out how loose your usb connection is--try moving the cable around.
shazzy84 said:
Something like that happened to me a while back where i couldnt connect. The problem wasnt the BA but was the cable connections- usb cable connections. It stills happens today where i get a bad connection and i have to play around with the usb that is plugged into my laptop. Maybe you should check out how loose your usb connection is--try moving the cable around.
Click to expand...
Click to collapse
I have tried many time, but not work
reflash
get into boot loader mode, connect directly to pc with good direct usb connection, (screen should state, USB from SERIAL on connection), reflash.
ensure SD card is removed beforehand.
AbuGWM5 said:
get into boot loader mode, connect directly to pc with good direct usb connection, (screen should state, USB from SERIAL on connection), reflash.
ensure SD card is removed beforehand.
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
Note: I have tried the following
http://wiki.xda-developers.com/index...UCK_AT_STARTUP
If you can get USB connection to your device, you can just try to reflash with same WM6. best of lucks.
restart your PC
Try reinstalling active sync on your PC or laptop and then shutdown your PC or laptop and then restart it. Then try connecting your BA afterwards.
shazzy84 said:
Try reinstalling active sync on your PC or laptop and then shutdown your PC or laptop and then restart it. Then try connecting your BA afterwards.
Click to expand...
Click to collapse
I did what you said, but my PC is still unable to detect my pocketPC.
In the pocketPC bootloader mode, I can see it change from serial to USB after I connect the usb bundle. What should I do?????
king2004c said:
Dear all
I try to connect back to PC, but PC can not find this device
Please help
Click to expand...
Click to collapse
try to disable windows firewall and any other firewall then try...
i have same problem my device can't connect to pc when i disable ISA firewall my ppc connected .
AddAn
addan said:
try to disable windows firewall and any other firewall then try...
i have same problem my device can't connect to pc when i disable ISA firewall my ppc connected .
AddAn
Click to expand...
Click to collapse
I have followed what you say, but still not work
I hear some people say that I can reflash the rom.
But
1. I don't know which rom they mean, my orginal one or updated one?
2. How can I get my original rom?
Someone say that if I try to connect via activesync under PPC bootloader mode, I could not see any connection in activesync, but I will hear some connection sound, then I can reflash my rom
But
1. How can I do anything if I can not see any connection in activesync
I have done what people say about using mytt1.24.
But,
What should I expect to see?
king2004c said:
Dear all
I try to update my PPC 6600 from WM2003 2nd edition to WM6. I download and run WM6 OS 5.2.2000 (Build 20000.1.0.0.PV.HAT). After I try to finish the last step of the installation which is to cool reset the PPC, there are 4 color bands and only show "NO GSM", "D 5.70.11 WWE". I try to turn it off, but doesn't work. I try to connect back to PC, but PC can not find this device
Please help
Click to expand...
Click to collapse
go here ftp://xda:[email protected]_1.15_Type_II/BA Radio 115 THIS WORKS.rar then use this to load your gsm extract BA Radio 115 THIS WORKS.rar somewere on your computer put your ba it to bootloader mode then put i into its craidle then run MaUpgradeUt_noID.exe wait till upgrade is done then take out of the craidle press reset button dont worry about activesync connecting
or not
update information
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
PPC6600 is a CDMA device and not a GSM, so you tried to flash a wrong ROM, sorry friend.
April 1 said:
PPC6600 is a CDMA device and not a GSM, so you tried to flash a wrong ROM, sorry friend.
Click to expand...
Click to collapse
could you please tell me where I can find the corret rom?
Hello to everybody!
After all I have to say that this is a fantastic forum for users of Qtek S200 (Prophet). I bought one last week and started to see what I could do. Therefor... I'm a newbie
This is my first thread, hope that some one can help.
After trying to understand the world of Prophet, I first changed the ROM to an official Qtek ROM.
Now I what to sincronize with my PC to transfer photos and put some software and apps in the card. Like I read here, I downloaded the activesync from microsoft site, instaled it and plugged the cable to my pda. Nothing happened. Than I went to activesync connections enabled USB connection and tapped in connect. After a search, the pda was simply not found. Even after turning down de AntiVirus and Firewall, nothing happened.
What happened? I have to do something in the PDA? Couldn't find that info in here.
Thank's in advance for the help
Heurd
Does the LED in the speaker at the top change to orange?
Does the computer react at all? (any sounds etc.)
If not, try putting the device into bootloader: Press and hold the COMM button and then soft reset, and then plug it into your computer and see if anything at all happens.
If nothing happens, the USB cable is damaged. If the computer responds when the device is in bootloader but not when it is in, the ROM may not have the required software installed in it.
Hi,
Yes, the Led turns orange. I can charge the battery with that cable. But i also read that it's possible in some cases to charge but the part to syncronize can be damaged!!!
But what really intregues me is that I used that cable to put the ROM that I have. Supposedly it's a Qtek official ROM, i don't know if you can conclude something with this:
IPL 2.10.0001
SPL 2.20.0001
GSM 02.47.21
OS 2.20.7.29
In PDA appears the active sync icon and tapping it only appears a window that says to install AS in PC and connect. So I suppose that it has something.
thanks to l3v5y for the sugestion... I will try and than post here what happened.
does anyone has anymore suggestions... I will try everything to put this at work.
In PDA appears the active sync icon and tapping it only appears a window that says to install AS in PC and connect. So I suppose that it has something.
Click to expand...
Click to collapse
This seems to say you haven't successfully installed Active Sync. Try restarting your computer and seeing if it works then.
l3v5y said:
This seems to say you haven't successfully installed Active Sync. Try restarting your computer and seeing if it works then.
Click to expand...
Click to collapse
That is surelly not the problem because I installed AS 4.5, restarted the computer more than once, removed that and reinstalled and nothing... I even had put de AS 4.2 to try and see if it worked - nothing.
Now I'm not in my computer... I will try what you suggested when I go home.
I think it may be something to do with the USB cable...
Had that problem a while ago, my solution was to reinstall windows xp and it worked. so backup your pc, format your hard drive and then install the os (windows xp/vista). i guess it was usb-driver related.
REALLY
Unbelieveble...
well, It's easier to try in another pc before formatting mine. I'm not in the mood (too much time to put like I like)
That way I will check and see if my cable and ROM are allright.
Thanks for the tip croco_64
Hope to tomorrow come in here and wright that it's everything ok
Hi there!
Well... I've tried what you proposed. It is probably a problem of the cable. I tried with a cable of a digital camera and finally the computer detected the phone (with mine it only went orange light in the top, but never recognized - despite I changed the ROM with it ). However it gives an error - the instalation is not complete!!! I went to device manager in the PC and there was a yellow (!) in the windows mobile device.
Is it of the cable!? Do the cable have to have specific properties to sync the pda and the pc? The camera cable isn't enough?
yes... I had put activesync 4.5 in the PC!!!
thanks again for the help
im using o2 xda ii
ROM VERSION: 1.60.00WWE
ROM DATE: 12/03/03
RADIO VERSION:1.08.00
PROTOCOL VERSION:1337.18
EXTROM VERSION: 1.60.44
HARDWARE
CPU: INTEL(R) PXA263
SPEED: 400MHZ
RAM SIZE:128MB
FLASH SIZE: 32MB
FLASH CHIP SIZE: 28F128K3
DATA BUS: 32 NITS
STORAGE SIZE: 14.54MB
LCD: 240 X 320 TFT
COLORS:65536
MODEL NO: PH10B
PLATFORM: POCKET PC
>>> can i upgrade my ppc to wm5 or wm6? can it be install without using the active sync or usb cable because i dont have one.
no not really
unless you got access to another phone of the same type
and can make a sd card with a rom on from that
Rudegar said:
no not really
unless you got access to another phone of the same type
and can make a sd card with a rom on from that
Click to expand...
Click to collapse
SO how i want to install new rom directly from sd card? the link please?
http://forum.xda-developers.com/showthread.php?t=355832&highlight=SD+flash
but as i said cable is required to make the sdcard with the rom on it
expansys.com have cradles or cables you can buy
but how could i install directly from the sd card? and the link to the rom that could be use?
it's in the thread i linked to
you need a himalaya a cable and a sdcard to make the sdcard
bootable for rom flash
OWHH i still need a cable also ar... cant use card reader aight?
rudegar....
i have a new problem.. my hp was showing just Serial and v 1.03...
how could i go back to my ppc??? i cant do anything with it because my ppc doesnt working at all just showing Serial... help me please anyone!!
no as far as i can read from the thread a himalaya and cable is required
sounds like your hp is in bootloader i would read the manual about how to reset it to boot up normaly
and if the os is damaged how to flash it with a new rom if there are roms for that hp device
so i just need a cable to do it right? n link to the software to update the rom?
http://wiki.xda-developers.com/index.php?pagename=HimalayaSDcardLayout
im sorry bro, seriously i didnt understand what its meaning.. so what is the cable name?? i just want to buy it from the store tomorrow..
http://www.expansys.com/p.aspx?i=133761
WHY my hima doesnt show usb at the screen?? and my pc showing there are unknown device??? how to solve it?? im in deep problem right now, i just bought the usb cable to my ppc.. any driver to it?
Now My Hima Has Been Bricked Theres No Rom To Be Reload.. And My Hima Cannot Sync With The Pc.. Im Doomed....
If you haven't even flashed your rom yet, there is absolutely no good reason why your device should be bricked. What is it currently doing at the moment?
What is showing on your XDAII's screen?
my xda ii just showing SERIAL and v 1.03.... ill have try to reboot again but theres nothing happen. the serial blinking but still in the bootloader mode. how can i cooked my device? my pc also didnt detect my hima...
It isn't bricked then, not even close. So don't worry about that yet
Simply plug it in to your computer with your cable, don't expect it to recognise what it is. And make sure you have ActiveSync turned off on your computer (if you have it installed which you may not).
Next, leave it a minute or two connected. Then, unzip the rom you downloaded somewhere on your computer, and then run the .exe in the unzipped folder. It may be called HimaUpgradeTool or something similar. It should eventually say it found your phone, and usually it has no idea what rom is currently installed. Then simply press the install button. It should show updating on your computer screen (it generally takes over an hour), and some fancy stuff may happen on your PDA screen.
Once it says it is completed (on your computer screen), unplug your device and Hard Reset using soft reset, Dpad, Camera and Record.
Select the options as follows: (for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
Your phone should reboot, and all will be well in world.
i think that i found what is my problem. i think that my usb cable is faulty because of my computer detect the usb then it shown unrecognised device. then i run the hima upgrade but it shows that there are no device attach. but my battery was heat like it was charging. ill try to change the cable first then ill try it again.
thanks all... my problem was being settle. now i know my problem is.. when i change the cradle i can upgrade my hima. thanks again.
Hi, I tried to get answer for my problems, but none any specific
so I`m startin a new thread...btw
My JASJAR has the same problem as lots of folks around here like it shuts off at any hard work like starting the camera or charge at 60%. I came to an end that as it works ok with the charger on, then the problem must be on battery. Well I'll try that
But the another problem is PC connectivity...it doesn't recognize the device
I tried MS Active Sync 4.1, 4.2, 4.5, windows 2000 SP4, xp SP2, different computer...just no luck, in bootloader mode it shows "serial" and "0.60" and whenever I plug in the USB, it shows USB, and then same, device not recognized...what to do?
And when I start the device, on blue background imate logo..it shows Radio 0.00.00, what does it mean..I can't even upgrade it as USB is not recognized...waiting for flash from SD, but no luck. Can any one sort these things out
First problem, almost definitively the battery.
Second and third problems could even be correlated, first the third problem/doubt, even if I'm not a complete expert, this means that your device was "unlocked" with the aid of a specific program that does just that (if you're interested in knowind how, go to the uni's wiki and read about unlocking), the Radio version 0.00.00 is just a "by-product" of that process.
So, if you're asking about this, you didn't do this by yourself, so you don't know what and how much has been done to your PDA, then for your second problem, first try a soft reset (this is always windows, remember it!), the re-connect the device (to the PC) and see what happens, then verify that you have the active sync program installed properly (and running) in your PDA, just when you connect the PDA to the computer, the active sync should become available as a running program, so, connect the PDA to the computer, the PDA turns on and says connecting, even if it does not connect to the computer you should see active sync running in your PDA, go to settings, system, memory, running programs and verify that it's there.
Another cause could be hardware (on your PDA), this means, cables and port or even internal (but this is quite unlikely).
Perform these tests and see what happens, then we'll see what else can be done.
Thnz, I trued several soft reset even hard reset,
I tried connecting to the computer with ActiveSync on, with some other software which changes the active sync connection to something like USB serial (from RNDIS ...), even advance networking off, taking out the SIM and memory card...running the device search..no luck.
and btw in computer after installing active sync it gives a window with all menu disabled except "File>Connection Setting". I tried by using bluetooth connectivity. No luck.
I read the thread about unlocking..and tried to do the rest..I mean the second step of unlocking, it showed device successfully unlocked..but all the same.
Any help....
mamaich method
Try this,
Step by Step :
get the tools at attachment , as mamaich told, you have to use it in bootloader mode , (Power + Light Bulb + Reset)
1. Stop Activesync USB connection
2. Uni : Reboot Bootloader then Connect USB
3. PC : Run mtty1.42.exe
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5. type : task 28 55aa
6. Press Enter
7. Cause DOC reformatted, so there's no rom in DOC ,try reflash any rom that you like .
For task 28 55aa in mtty success , will show the message (attachment )
DONE .