hi i am looking for a new screen for my xda2, i have an other one with bits missing for spares to swap if you are interested
Bits missing
How many bits is missing - can You attache a photo?
Maciek
the back cover is missing and the screen is broken, it is only the phone no other parts
Related
If anyone needs parts for the 8125 or mda, PM me coz I've got lots of parts lying around from repairing some phones. I've got some 8125 casing and keyboard working. 2 Working Flexboard but one broken on earpiece and the other on lower buttons. 2 broken mainboard. 1 broken digitizer but the glass is ok. Lots of screws, 3 working camera lens, speakers, two working keyboard.
Here is a link to my threading history.
http://www.heatware.com/eval.php?id=41722
PM me if you want pictures or email me at [email protected]
This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.
I replaced my digitizer recently and when I put the phone back together and turned it on, the LCD looked different any thoughts or suggestions. I looked through some other threads but nothing described look like the problem I am having.
I guess the digitizer isn't original and polarizes the light in a different way, giving the strange optical effect.
Another issue maybe the digitizer is stuck tightly against LCD, try to put between the two a strip of thick adhesive tape around the edges, avoiding tight contact.
Or worst, maybe you damaged the LCD while disassembling, to verify this lift the digitizer and see if it looks the same or not without digitizer.
It looks as though it is a similar problem to * HERE *
I you go into your Web-browser and press the menu button, then view page info.
Look at the background (the webpage). What are the colours like?
I finally didn't avoid dropping the Blade, although it is in a silicon case wearing outer protector sticker too. It fell face down i think on another item (they were in a fanny pack). Unfortunately, there was a crack all across the display when i checked it out. So i took the phone apart, found the display part that i need in ebay. The thing is every part either clips or zifs, except for the display itself and the volume button. The display was glued on the frame with some kind of stickers, i wonder how i should go about and install the new display, because it appears the two stickers are on the frame and not on the display so i guess there will be no stickers on the new part and the sellers specifically state "instructions not included, make sure you know what to do yourself". I have found instructions on outer screen change, but not for display change. The same applies for the volume button which was glued on the frame. Should i use some kind of glue for the display? And if yes, what kind of glue? Or should i search for these special stickers? And where would i find these, if they re not even mentioned anywhere i looked at? Thanks for any info guys..
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
any body ????
muhama said:
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
Click to expand...
Click to collapse
any body ????
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Mister B said:
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Click to expand...
Click to collapse
Thanks for reply me:good:
How can i open my phone? And where is connector located?
Do you have a link to view that?
Have a read of this thread for start
http://forum.xda-developers.com/showthread.php?t=1566179
Plenty more if do a search
Basically be very very careful, use plastic pry tool ONLY to remove back, start at top. 2 clips about 7mm in from top edges then once released work down right side, DO NOT stick any tools in near the volume key, if doing it right the back comes of very easy (2 pry tools are better as can keep one in top sstopping it clipping back in)
Once back off handle with care, rough handling breaks th spring contacts for antenna etc.
LCD from mainboad can be disconnected from mainboard without fully removing flex & is absolute best way do it.
I did write few posts on it so will try dig them up & link you.
If buy lcd/gigi assemble also buy a button board ribbon as they like only $3USD, with spare button ribbon you can easily plug new lcd/digi in & plug new button board ribbon into mainboard & hold a battery on it to do a test befoe sticking things together.
Also you likely damage ribbon if not careful so spare likely get used on rebuild.
Parts link is in HD2 Wiki
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips