I have (Qtek 1010) PPC . and i want to programm it using Appforge (Mobile VB).
the problem that i am facing is how to access the Build in GSM port in the set and how to write a program that dealing with the gsm by send and receiving SMSs .
do any one did that or know anything about it .
please help.
regards
hello i have an big problem my wallaby dont connect to the phone network so i can't use the phone
please can someone help me i live in the netherlands my operator is tmobile
my rom version is 4.01.16 ENG
rom date 02.04.04
radio version 6.24.00
protocol version 324e4
is this wrong??
please help
greeting cor
Try entering bootloader, power switch held down while pushing stylus in reset, then push the button below the antenna, then choose 900/1800. You will need to do a backup first.
Your rom versions show that it is PW10B1 version (north american version GSM 900/1900).
If your local SP provides GSM 900 service, switch the band to GSM 900 (Setting > phone > Band > choose GSM 900
i have set the gsm band to 900 but it won't help he is stil searching for network
does someone have another solution???
There is another possibility, your phone is PW10A1, but the firmware and radio stack had been "upgraded" to PW10B1. So you won’t get any signal.
Check the label on back to see it is PW10B1 or PW10A1.
yes you are right that is it but where can i find the good stuff
so i must change my hardware version to pw10a1
any idea how i can change that??
now i have tries to update it via asimagetools
but i get a message
itsdcardinfo:niet nader omschreven fout
error opening target device
please can someone help me
civiccoupe said:
so i must change my hardware version to pw10a1
any idea how i can change that??
Click to expand...
Click to collapse
Buy a new device (PW10A)....
No ohter way to change hardware......
Stefan
you need change radio stack back to PW10A, but risky
so i cannot set it back to PW10A ?????
civiccoupe said:
so i cannot set it back to PW10A ?????
Click to expand...
Click to collapse
you can flash the radio stack back to PW10A
civiccoupe said:
so i cannot set it back to PW10A1 ?????
Click to expand...
Click to collapse
Well, my device is PW10A1, but when i had T-Mobile 4.01.16 rom on my xda, it said PW10B1. Therefore check the back of your xda, if it says PW10A1 then you HAVE that version, just the rom says not. hehe. About flashing: you can not use programme a to flash your XDA when you have an T-mobile rom on it; you can only flash it with the SD-card method (use forum search). Try to flash in an 4.01.12 version (O2), i found it better than the T-mobile one.
massage for cgigate and stefan
Hello all,
I have a XDA i have a problem with the radio stack, Frend of mine did and upgrade of Rom and Radio, and he did a PW10B1 radio upgrade is there any posibbileties to downgradit to PW10A1.
Thanks in advanced
I upgraded my XDA I with the original Tmobile upgrade PPC2003 GER. All works fine. Then i started the Autokonfiguration for Tmobile Germany. One Programm i got was a tool for mms-sending and receiving. When i want to start this Programm an error message occures like "This software is only working on original T-mobile device". What can i do ? Where is the difference between my XDA I and the MDA I ?
My Device-Information shows:
ROM-Version 4.01.19 GER
ROM Datum 03/05/04
Radio Version 3.23.11
Protokoll Version 32S54
Identity : PWA10A2, Pocket PC
thanks for your help !
the difference is only the software
try doing a search for mms composer in the forum it should not have any special relation to any operator of cause you may have to put in the mms settings manualy
thanks for your answer,
using mms-composer is one possibilty. But i thought, when flashing my XDA I with the original ROM of the MDA (T-Mobile, PPC 2003, German), there would be no difference to the original MDA I, and then using the MMS-client-Software (Materna, ANY WAY) from T-Mobile Germany shouldn't make any Problems. When starting the MMS-Software the message "... Software only for T-Mobile Devices" occurs. This means, there must be another difference to the MDA. Any idea ???
Hi,
i have found the solution for my own. Here for all who are interrested:
- the difference between a MDA1 and XDA1 (with MDA-ROM) is the imei-number
- the MMS-Client-software from T-Mobile (Materna, ANY WAY) needs an imei of a T-mobile MDA
- it must begin with 350512... or 350513... following with a serialnumber of T-mobile
that's all :wink:
Hi I have an XDA II on o2 PAYG . I spoke to o2 and one person told me you cand use GPRS and another told me I could , I have now got that working , I still cannot read my sim adress book or any other phone parts. I get the Please wait 15 seconds message .
Any hhelp would be appreciated , but I need it in basic terms as i am not xda profficient yet.
ROM Version : 2.02.t1WWE
ROM Date : 05/17/04
Radio Version :1.18.00
Protocol Version :1337.38
ExtROM Version 1.60.50
Thx in advance
Orange SPV M1000
--------------------------------------------------------------------------------
Hi all,
I have an Orange SPV M1000 i am trying to unlock, i have tryed all the methoods i could from the site. I have managed to get the phone to accept other networks sim cards but when i attempt to make a call it dials then hangs up.
Can anybody help?
Is it somthing to do with the radio rom version?
r 1.10.00
g 13337.18
d 1.66.00wwe
PLEASE HELP!!!!!
Hi,
My SPV 1000 is exacly the same as yours (same radio and OS). I used the new xda2 unlock utility and it worked like a charm.