Related
ok i think iv killed my m600
i flashed it with the older imate rom the 1.0.9 version
it installed 100% and rebooted and from ther it was stuck on the imate screen for like 10 minutes and i see the following text in red on the top left corner
---------------------
IPL 2.10.0001
SPL 2.15.0001
GSM 01.14.20
OS 1.0.9.25
-------------------------
i tried removing the battery and restarting the fone. still the same thing. can someone please please please help me with this?
what do i do?
im sure orange wont help me out since i flashed it with a non-orange rom.
never mind fixed itby goin into the bootloader
funky_Saggi said:
never mind fixed itby goin into the bootloader
Click to expand...
Click to collapse
hi there i seem to have the same problem as you with the boot screen. top left corner say's
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
can you please tell me how you fixed yours please it would be a great help
What you could do is flash it with an newer rom
Hold camera button AND reset (be asure that it hold it while resetting)
Then... you are in you bootloader... connect the PDA with your PC..it will recognized it!
Then run the romupdate ;-)
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
crossy4life said:
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
Click to expand...
Click to collapse
Aren't you getting "USB" written in the bottom left corner of the 3 colour screen when you connect it to USB?
Yes i get the USB come up at the bottom of the screen my computer does not do anything. can you tell me which ROM i will need as the ones i have to run the ROM update but it comes back saying connect to ActiveSync which i can not do is there a way round this?
Final got my SPV M600 Working with the ROM from the download area thanks for the help anyway
cheers
just change the usb port to another one and start rom it should pick it up
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
I dragged my Mini s out of the draw thinking it dead for the past few months, after using the battery jump start trick got her up and running again. now, after using mobile 6 on my other HTC i wanted to upgrade on this one, nothing fancy just bog standard mobile 6. its an O2 G4 model, I also checked it with the wizard service tool. I then used the hard SPL G$ tool to unlock it, that went fine. the device repowered and worked. I then tried to load in windows mobile 6 from this thread
http://forum.xda-developers.com/showthread.php?t=355591
after its started the flash I got an error message saying "error 300 invalid update tool" please get a newer tool, I have tried to run it again and now get the message " error 2641 cannot connect " and now all I have is an XDA with a red, green and blue screen showing IPL2.21.0001, SPL 2.21,0lip and "usb" in the bottom left corner
is it bricked? can I recover it, I will be gutted if it is bricked as I followed the instructions to the letter
btw I havnt disconnected it from the USB at all, just leaving it there until I get somne advice from here
update, bit the bullet and unplugged, soft reset and its all as it should be, on windows mobile 5.
so my question now is why didnt the Rom update in the link above work? or am I just a noob doing it wrong...
try downloading another rom and flash it again...even if it isn't connected in activesync ignore that and flash away...if that still doesn't work try your original rom wm5 and then flash a wm6 again...it's not bricked(see below)
stevescoots said:
I dragged my Mini s out of the draw thinking it dead for the past few months, after using the battery jump start trick got her up and running again. now, after using mobile 6 on my other HTC i wanted to upgrade on this one, nothing fancy just bog standard mobile 6. its an O2 G4 model, I also checked it with the wizard service tool. I then used the hard SPL G$ tool to unlock it, that went fine. the device repowered and worked. I then tried to load in windows mobile 6 from this thread
http://forum.xda-developers.com/showthread.php?t=355591
after its started the flash I got an error message saying "error 300 invalid update tool" please get a newer tool, I have tried to run it again and now get the message " error 2641 cannot connect " and now all I have is an XDA with a red, green and blue screen showing IPL2.21.0001, SPL 2.21,0lip and "usb" in the bottom left corner
is it bricked? can I recover it, I will be gutted if it is bricked as I followed the instructions to the letter
btw I havnt disconnected it from the USB at all, just leaving it there until I get somne advice from here
Click to expand...
Click to collapse
Download this RUU ,extract it and replace all the files in the folder with the RUU files in the Rom and run the RUU,it'll flash successfully .
stevescoots said:
update, bit the bullet and unplugged, soft reset and its all as it should be, on windows mobile 5.
so my question now is why didnt the Rom update in the link above work? or am I just a noob doing it wrong...
Click to expand...
Click to collapse
Your ROM Update may not have worked because, maybe it was not built for the G4 Wizard. so try anyother ROM
xda2_hasseb most of the WM6 roms available for download on xda-developers are G4 safe as they don't conntain ipl and spl flash....so you can safely flash a Windows Mobile 6 rom without bricking your Wizard
'XDA Mobile 6 Release 5 FINAL' is the latest custom build wm6 rom,build for both the devices,it can be flashed to both the devices G3 and G4 safely,its one of the most favourite roms.
Thakx xardas_90, i knew they didnt had the IPL and SPL with them but i didnt knew that it was IPL & SPL not the ROM it self that caused the Bricking of the G$ WIzards i thought Windows ROM for G3 and G4 were different but THANKS for the info. TC
Thanks for the advice, got it done and works a treat, except no data transfer or sms or net conncetion, still soldiering on, at best it will work, at worst, well i guess my son gets a hand me down lol
stevescoots said:
Thanks for the advice, got it done and works a treat, except no data transfer or sms or net conncetion, still soldiering on, at best it will work, at worst, well i guess my son gets a hand me down lol
Click to expand...
Click to collapse
You need to get GPRS/MMS settings configured,get these settings from your carrier,only then you'll be able to connect to internet/SMS/MMS, or check out the 'XDA Mobile 6 Release 5 FINAL' rom thread,you might find the appropriate GPRS/MMS settings there of your concerned network.
Hi guys,
A few months ago I updated from O2s 6.1 to a 6.5 ROM.
Now I want to go back the O2 ROM but the update freezes at 34%. The popup box says it lost connection with the phone.
I tried installing HardSPL but it didnt help. So I tried a hard reset but now I just get a RGB screen with
POLA200 MFG
SPL-2.20.OliNex
CPLD-2
Any suggestions in sorting my problem would be appreciated
Many Thanks
rikpotts said:
Hi guys,
A few months ago I updated from O2s 6.1 to a 6.5 ROM.
Now I want to go back the O2 ROM but the update freezes at 34%. The popup box says it lost connection with the phone.
I tried installing HardSPL but it didnt help. So I tried a hard reset but now I just get a RGB screen with
POLA200 MFG
SPL-2.20.OliNex
CPLD-2
Any suggestions in sorting my problem would be appreciated
Many Thanks
Click to expand...
Click to collapse
First of all check your USB cable... and choose another USB port to connect the cable and try to flash your ROM again
Try this as it has been solved before may help you out
http://forum.xda-developers.com/showthread.php?t=425922
same problem
hi everyone. I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
Many Thanks for the replies.
I followed the link and i'm confident it will solve my problem. Unfortunately I cannot get mtty to offer "USB" from the dropdown. I remember going round in circles trying to get USB show a few years ago with a SPV C550.
If anyone can help me, that would be great. I'm using Vista. This might be why the steps in both the initial post and replies on the first page don't work for me.
Hi i have flashed my phone with the new Artemis_v240_WWE rom, everything went ok, did hard reset etc and phone worked fine, then it locked up after about a hour so i pulled the battery and rebooted, now i cant get past the first white HTC screen with the RGD info at the bottom, it's just stuck!! I have tried to put the usb in and attach it to my laptop but it's still doing nothing?? Please can someone advise me on how to get out of this.
Thanks
ok i got a update, i can get it to the bootloader screen but it's not being seen in active sync, please help
did you remember to flash the cooks recommend radio?
no i never flashed a new radio as i thought the one i was using was ok as it worked with artemis v19 ok, is there anyway round this, if the radio is wrong?
i am getting to the bootloader screen ok but i cant flash anything cause it's not being seen in active sync?
Beatkeeper said:
i am getting to the bootloader screen ok but i cant flash anything cause it's not being seen in active sync?
Click to expand...
Click to collapse
i remember the active sync will not show anything if you enter the three-color bootloader screen...
try to flash a new rom...
so long as the white area says usb you can flash.