Database Users

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Trinity, nearly dead after ROM update

Hi,
I started a new thread because on my previous post I did not receive that much reactions so I try a brand new one.
A few months ago I bought this, in my eyes, really cool HTC Trinity, aka the P3600. One of the main reasons I bought this device was because I read on some forums that this device had GPS functionality, but at that time it was not supported/ebabled yet by HTC but properbly would be in the future. Off course I could not wait, so I tried to install a Dopod version which should enable GPS functionality. Unfortunately I've got a Dutch version of WM5 running on my PDA, so a ROM upgrade was not possible, unless the CID lock is removed. In order to accomplish that I downloaded the tool SSPL, installed it, and executed it on my PDA. After that I tried to install the Dopod ROM, but during the upgrade it froze up. After rebooting, the device frooze up during the startup (when it is display the MS logo for push mail). After that I retried the to run the update, but unlucky me, it stucks at 1%, then device reboots, and I receive the "ERROR [294] : INVALID VENDER ID". on the screen of my PC. My PDA is now worthless because it still freezes up during tje startup.
I' m still able to access the bootloader menu however but none of the ROM updates that I have at my dispossal are working. Unfortunately I do not have the Dutch ROM in my possesion and a quest on the Internet lead to nothing. However, this week I will receive a Trinity at my work (exactely the same). Is it possible to make a backup of this ROM and then restore it back to my nearly dead PDA? Or should i deal with this dead PDA in anoter way to bring it back to live again.
Any help is more the welcome

Follow this thread to CID unlock then just re flash. This should take care of your invlaid vender issue.
http://forum.xda-developers.com/showthread.php?t=293957

RebelShadow said:
Follow this thread to CID unlock then just re flash. This should take care of your invlaid vender issue.
http://forum.xda-developers.com/showthread.php?t=293957
Click to expand...
Click to collapse
JolietJake's Trin is not booting to OS, he can't run SSPL

stepw said:
JolietJake's Trin is not booting to OS, he can't run SSPL
Click to expand...
Click to collapse
Yep, that's right... If I only could

You may have to suck it up and pay for the unlocker from IMEI-check. I may be wrong, but I think you run that from your pc and only have to connect your trin via usb. I'm just not sure if you need a valid activesync conncection to use it - as you probably can't get that with a "zombie" trin.
Do a little research first if you are going to try.
If you try it, good luck!
http://www.imei-check.co.uk/m700unlock.php

psargent said:
I'm just not sure if you need a valid activesync conncection to use it - as you probably can't get that with a "zombie" trin.
[/url]
Click to expand...
Click to collapse
I indeed need an active sync connection, which I have.....
....during 10 seconds or so (only just after I rebooted the TRIN)
I also tried to use this tool in Bootloader menu. It's able to set up a connection through USB, the screen on my PDA goes gray and the message ".....ERROR" appears on the screen of my PC. After that the TRIN reboots and freezes up again . Fortunately I did not pay for the tool yet, i just downloaded it)
However I appreciate your help very much!

psargent said:
You may have to suck it up and pay for the unlocker from IMEI-check. I may be wrong, but I think you run that from your pc and only have to connect your trin via usb. I'm just not sure if you need a valid activesync conncection to use it - as you probably can't get that with a "zombie" trin.
Click to expand...
Click to collapse
Too bad, it's the same story, it needs OS/ActiveSync to be running to re-enter boot and flash SPL.

Is my Tmobile MDA Bricked?

Ok i was trying to get XM6 on it. And i got the error code 300 so i tryed this other rom to make it work"ROMUpdateUtility_Wizard_NoID" and now when i turn my phone on it just go straight to the 3 color dos looking screen it shows my IPL and SPL and thats it, i cant get out of it please help me !
Thanks
If any one can help me Get XDA Moible 6.0.0.0 working on my MDA i will paypal them some $money$
My aim is deathblooms237

U are in bootloder mode. Thats fine. U didnt bricked ur phone. Now u can softreset ur mobile. By infrared eye u will see a hole and with your pen restart ur device.
BUT FIRST you have to know if u have G3 or G4 model. if your ipl/spl is 2.21.0001 - with 3 zeros than u have g4. READ ALL ABOUT G4, cause if u use rom for g3 or any rom which isnt for wizard OR ANY ROM WHICH contains IPL/SPL u are SCREWED UP. YOUR mobile will die and u could just throw it away.
SAFE ROMS for g4 are: NBD, faria, OCTAIVOI's etc. See a few on this link: http://wiki.xda-developers.com/index.php?pagename=wizard_WM_6
AND you should also read ALL about sSPL method - GREAT, FANTASTIC WAY TO FLASH YOUR G4.
http://forum.xda-developers.com/showthread.php?t=329147

Ok i should have a G4 myILP is 2.26.0001 my SPL is 2.26.0001 and when i soft restart it it goes back everytime to the boot screen the 3 color thingy. i just dont know what to do, plz pretty plz help./ Whats the next step
this is the only roms or files i have used
English Update Utility Files G4
ROMUpdateUtility_Wizard_NoID
T-Mobile-UK_2.19.11_Radinly
Wizard_Love_2[1].26.10.2_WWE_Novii_CF2
XM6r3

Try flashing your operator's official rom back into the phone to begin with. That should get you at least a working phone again.

Check the XDA-Wiki (button on top of this screen) on the Wizard section how to troubleshoot or unbrick your phone

Ok i got it back to facotry reinstalled the tmboile software from the website but to give a heads up i have cingular useing a tmobile phone so its already unlocked. ok now i need to find away to install XDA Mobile 6.0.0. now quick question is this as close i can get to the windows mboile 6 eye candy, but thanks atlist i got my phone back up and running but can some 1 tell me the files i need to get started on XDA Mobile 6.0.0.
Thanks
Ok this is what happends i tryed to install XDA Mobile 6.0.0 and put the file ROMUpdateUtility_Wizard_NoID in the folder and click ROMUpdateUtility_Wizard_NoID and it installs and when it gets done it goes right back to the 3 color screen. am i doing something wrong, reason i use ROMUpdateUtility_Wizard_NoID is because i get error 300 with out it when i try the XDA Mobile 6.0.0 normaly.

plz help

My heads spinning from all the information aka post and threads, but im still stuck like my wizard on the 2nd splash screen.
I wasnt trying to upgrade the rom jst clear storage but after everything ive read i would like to upgrade to wm6 but first i want to get my wizard working.
I tried backing up the rom to the sd card but I get "You didn't get the proper security level to download a specific image" So i take it my wizard is cid locked.
My IPL:1.01 and SPL:1.06 does that mean its a g3. My activesync 4.5 doesnt pick up my wizard is it because it cant boot, i tried with it in bootloader mode still doesnt pick it up.
So plz point me in the right direction to fix my wizard

ok i think the place where im stuck at is cid unlocking my wizard with out using that imei site. any help or is there another way to do this.

This helped me when I was stuck on the first screen. For some reason, the Radio file was gone. Follow this exactly, it works. In my case (sounds like yours also), at the end of this you will at least have access to the phone again.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=bootloader
After your done. You will have a RGB screen, then follow these directions to load a base rom and unlock so you can keep going until you ca load WM6.1.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I've had many, many problems over the last 3 days trying to do this. I completed it all in less than a day, but when I used the phone it had terrible reception. I completely downgraded everything back to square one. Still bad phone reception. I was about to through it out the window, when someone called my wife's cell phone and she also had bad reception. I then put my sim in another phone, same problem. Well, at&t has a tower down for the last 3 days. What timing, it seems to work when not at home, but hard to test that way Anyway, moral of the story is. Don't give up, keep plugging along.
Good luck.

I'm pretty sure imei checker is for SIM unlocking.
For G3 CID unlocking and upgrading read the stickies in http://forum.xda-developers.com/forumdisplay.php?f=289
If you can start your Wizard in bootloader, and it says "usb" in the lower-left, you can flash your original ROM. An active sync connection is not needed. Search for your carrier's ROM if you don't have it and I'd recommend the "no carrier ID" version of the RUU.

Have you tried a 'Hard Reset',hope it'll work,if it boots up into working OS and it already has IPL/SPL 1.xx,use lokiwiz02b tool to SIM/CID unlock the phone and than upgrade.
If it doesn't work still after Hard Reset,most probably,its Extended_Rom is corrupted,its required to reflash a new rom.
Activesync doesn't work in absence of a working OS and in Bootloaders mode.Its not required for flashing a rom.Just get the phone into Bootloaders and hook the phone with pc via usb cable and watch small usb appear at the bottom of the bootloader screen,if its there,it good to go and flash the rom.

ok so i downloaded the button rom finally but how do i flash it to my wizard.

Get your phone in Bootloaders,hook up the phone with pc via usb,watch small usb appear at the bottom of the Bootloader screen,if its there run the 'RUU' application,it'll start to flash,it stops at a certain percentage,don't get worried and do anything,after a couple of minutes it starts again,let it complete 100%,the phone'll restart and boot up in new OS.

which ruu application. I jst downloaded 1 which comes in the form of a rar file saying ruuwrapper. is that the right 1

So after lots and lots and lots more reading i realized i dont need a ruu. all i need to do is get into bootloader mode plug in the usb and run the wizard button rom. It worked perfectly my wizard is back to life yip pee.
Anyway i wud jst like to thank u guys for all the help and compliment u guys on a gr8 forum.
Now my next challenge is wm6 with touch flo.

New member needs help!!

I unlocked a Cingular 8125 and went to load TNT Professional ROM. The phone kept losing communication at 99% and when I went to reload the original ROM from HTC's site, now I have NO O/S. I DO have another one, but my wife is using it until we get her a pink BlackJackII. I really like these phones, and can't believe I crashed this one! I don't have any Mini-SD cards. Any way to rebuild this thing?

Nobody has any ideas for me? I really need to get this phone running again!

Your not using Vista are you?

Most comm errors are due to weak or discharged battery,not having enough juice to complete the the flash,get it fully charged and try again,secondly,Yes! don't use winVista.
Download the official stock rom and flash to recover back.Get the phone in Bootloaders (RGB screen) hook up the phone and watch small usb appear at the bottom of the Bootloaders,if its there,run the rom to flash,it'll start to flash,but if small usb is not present than most probably its a comm fault.

I was using a Win2K machine. I had 2 batteries that were fully charged. I have a friend that will lend me his miniSD adapter and use my 1gig microSD card to get the info off my wife's phone and copy it to this one. He has a Sprint version of the AT&T Tilt. Might see if he wants to check out this site.

OK. I have access to a miniSD card now. Do I just take my wife's 8125, make a backup from it, then put the card in the bricked phone and load bootloader?

Read this thread for more specific instructions :-
http://forum.xda-developers.com/showthread.php?t=276963
But this method will only work if both the devices are already CID unlocked.Secondly,most important,both the devices shud be of same DOC Chip version,G3 or G4.If you back up a rom of G3 on a G4 device,it'll brick it and vice versa,make sure both the devices are of same DOC Chip version.

They are both G3's. I think they may even be from the same batch. If I unlock hers, won't I lose all her data?

YUP ! but first make a back up of all the personal data on her phone to your pc,for this use either 'PimBackup' or any similar back up application and than unlock it.Its necessary to have both phones CID unlock,otherwise,this method won't work.

OK, I used Lokiwiz 3beta and superCID unlocked the other one. When I run mtty, and use the r2sd all command, I get
R2SDBackup()-Download type=5
usTotalBlock= 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
I have left it sitting there for an hour and nothing else happens. Isn't it supposed to have several more lines of text scroll by? Also, I can't figure out how to get the dead one to boot to the miniSD.

ok,did you read the method carefully,the link I posted above ? you are getting it correctly.
This methods involves many steps.
Step 1.
Back up all the data on your wife's phone to your pc with 'PIMbackup',than downgrade to IPL/SPL 1.xx either through flashing 'Button's Rom 1.05 or you can even flash official stock rom Aku1 for this,when getting IPL/SPL 1.xx either way,apply lokiwiz02b and not lokiwiz 3beta to CID unlock your wife's phone,or you can use WST_4.2.2 tool also to CID unlock it,but its must to have IPL/SPL 1.xx to CID unlock in both the ways.Only after getting the phone CID unlocked,you can Backup the rom on a miniSD card.
Step 2.
After successfully back up of the rom on miniSD card,insert this card in your dead phone and get the phone into Bootloaders mode (RGB screen).
Step 3.
Run the MTTY command to back up from miniSD card.This is only possible if you already have this phone CID unlocked,otherwise it won't work.
Both the devices must be CID unlocked.
Although,I'm still not sure if it works,but there's no harm to try,may be it gets going.

Is the progress bar supposed to change back and forth from blue-green to red while flashing?

YUP ! it changes during flash,but it'll become green on 100% completion and the phone reboots.

OK. I can't get this thing to take the WizardLove ROM, can't find Button's ROM, but I am trying to load the XDAMiniS ROM now. On my third try and the SPL still says 2.25. Battery is fully charged and I get an immediate connection failure trying to load WizardLove. I really wish I could find the original Cingular ROM for this phone, not the new(er) update.

Download Cigular official stock rom from here :-
http://www.htcamerica.net/support/8125/software-downloads.html
or
http://download.america.htc.com/RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe
Check out this link for all the Roms like Buttons Rom T-mobile 2.26 etc
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies

I am just about ready to give up on this thing. No matter what I do, when I try to boot it up regular, it still keeps freezing up and when I try to do a hard reset, I get a format is failed error message.

Last ditch effort
Can I use WST to make a backup RUU from the working phone and flash that to the dead one? All other attempts have failed to restore this phone.

I dont think so
Men you are already doing everything!!!
Does you have mtty... try this please it may works for you let us know what happend please...
http://forum.xda-developers.com/showthread.php?t=420785 the man in this thread stucks on splash screen so read just the mtty steps.
BTW does you unlock your wife's phone... is yours unlocked too? before do it...please respond.
The hope dies at the end!!!!! we have so much to´pics about this issue... why you are runing windows 2000? nad make upgrades? or does I missunderstood? extremely recomended Win XP.

I have Vista at home, and I read where many people here say that you can't do reflashes with Vista, so I use my computer at work, which runs Win2K. I haven't unlocked the second phone, but I thought that I did the first one. That was why I went to flash it. I wonder if the unlock didn't take and that put me in this predicament.

I understand now
Maybe a mistake using windows milenium or 2000 or whatever...
So if it say format failed i cant imagine other thing that do the thing i post you... so if you got questions about clear DOC Chip ask everything...
when you already get everything in a XP machine tell us please oh just for a recomendation unplug the minisd and during the process the mtty working on some lines dont launch programs check your USB cable maybe with a little scratch and moving makes a false contact at all.