After installing Pocket Bluetooth Tools, COM1 doesn't work - MDA II, XDA II, 2060 General

I have been using my XDAII for a few weeks very successfully with the TomTom3 navigator software and a GPS receiver connected to the serial port (on COM1). Then I decided to install the Bluetooth tools from http://bluetooth.i-networx.de to try and use my phone with a Nokia bluetooth car kit. Unfortunately it didn't work, but now COM1 is unavailable.
When I run my TomTom navigator, I now get the error message 'COM1 is unavailable', and I've noticed in ActiveSync that if I go File>Connection Settings, it shows COM1 as unavailable and greyed out in the selection box.
Performing a Hard Reset hasn't cured the problem.
Does anyone know how to make COM1 available again?

Try going to settings/connections/beams and make sure beams is unchecked.

Related

XDAII / Tomtom 3.07 / Aktronix -- Please Help

I recently upgraded my Bluetooth GPS Receiver from a rikaline 6030 to an Aktronix with 16 satellites but i can't make it work with my XDAII and Tomtom 3.07.
I can pair it. But when i start the Tomtom GPS Tracker, it can't seem to connect to the Aktronix GPS Receiver.
Any Help will be greatly appreciated
Which port are you using for the gps? Did you accept serial profile when gps was being bonded. Try choosing tomtom wireless gps and bt gps in the bottom box.
I tried to use com 1 port, but xda issued an error saying that com 1 doesn't exist. I then tried 4, 5, 7, 9 to no avail. I tried selecting tomtom wireless gps and bt gps but it still failed to work although that's the setting i used for the rikaline 6030.
The aktronix uses nmea chipset and the manual tells me to use it as an spp slave but xda doesn't have that option. I also tried installing pocket Bluetooth tools but when i tried to pair the aktronix GPS, there's no port number in the serial option. It just has a blank field...
Hopefully you guys can help me sort this out
Try the following under the GPS section (2nd page where the world map is).
Top dropdown = NMEA 0183 v2 Bluetooth
Bottom dropdown = Blue tooth Serial Port COM6
Make sure the box is "ticked"
Also, switch on Bluetooth, go into bluetooth setting,select service, highlight serial port and make sure there is a tick in the Enable service box.
HTH
Kevin
I've selected NMEA 0183 v2 Bluetooth and Com 6. But when i went to bluetooth settings, i can't see service on it. All i can see are:
================================
Bluetooth Beam Authentication
Authentication Required
Bluetooth ActiveSync Setup
Press start button...
Bluetooth Serial Port Setup:
Inbound COM port: COM4
Outbound COM port: COM5
================================
Is this the service that you're talking about? If not, where can i find this service thing that i need to highlight.
ROM Version 1.72.00WWE
Radio Version 1.17.00
ExtRom version 1.72.187
Looking at those setting you should be choosing com 5 for your gps. It should also work by choosing tomtom wireless in the top box and bt gps in the lower box in tomtom gps settings. Try removing the gps from your bonded items, reset the xda then rebond, it should offer to act as serial port profile, answer yes to this.
I also tried installing pocket Bluetooth tools but when i tried to pair the aktronix GPS, there's no port number in the serial option. It just has a blank field...
Click to expand...
Click to collapse
This is the same problem for me, but with a Royaltek RBT-1000, XDA II and Pocket Bluetooth Tools installed...
Any solution?
Well, I have a similar condition.
O2 XDA II, AA Navigator and Fortuna Clip-On Bluetooth GPS.
It has worked before with TomTom, it STILL works with Microsoft Pocket Streets - you start it and it shows the GPS data.
AA Navigator automatically detects the device, setting the data to COM5 (which seems right to me - Outbound port which means the XDAII initiates the link) and speed to 4800. This is the same setting which is used by (working) Microsoft Pocket Streets, so I'm pretty much confident that the port would be COM5.
Yet when I confirm this, it still says <unplugged/setup wrong>... and the blue LED on Clip-on does not pulsate just like it does when there is the reception with other working software...
Wrote e-mail to AA support (I'm no fool to ring £1 / minute support line...) and waiting the answer... not going to resort back to TomTom...

GPS and TomTom5 Problems

I recently purchased a bluetooth GPS receiver (branded as Fusion with X70 as the name on the back - purchsed from Polstar) and TomTom5 software but cannot get the two to work together.
I have bonded the receiver and set it as COM7 and I can choose that in TomTom5 as the COM port to use but it always says "No GPS Device!"
I have also downloaded and installed the BlueTooth Tools software but this hasn't helped either.
I have an o2 XDA2 and any help with this would be much appreciated.
I think mine is set to BT on com6. You must make sure the GPS receiver has a satellite signal before you try to configure tomtom (flashing light or whatever). Keep trying different settings, that's what I did
I think I have tried all the settings I can, I am beginning to wonder if i've got the correct version of TomTom5 installed! My device information says my platform is PocketPC and that is the version of TomTom5 I installed.
I have tried various settings and soft-rebooted my phone in the meantime after each change and tried without re-setting too!
This is getting rather annoying now
sorry, I'm using com5. Have you made sure you've got a satellite connection first.
Mine is version 5.000
When I turn on my GPS receiver I get two lights flashing, one to indicate that the bluetooth is sending a signal and the other to say that the device is receiving a GPS signal.
Try this...
Hi Dave,
Did you buy this via eBay? Couple of friends have bought from the same guy and neither worked, even though it seemed that they were (flashing lights, bonded etc). Both Polstar/Fuzion.
Anyway, if it won't connect via 'other bluetooth', try selecting 'other cabled device' and then select 4800 baud and your bluetooth com port.
Don't know why, but have had to do this with 3 different PDA's so far (2 XDA, 1 ipaq). It seems to work fine, although the data rate's a bit slow.
Any bluetooth gps I have has installed as com 5 when bonding, it asks if you wish to install serial profile and allocates com 5. I have noticed however that tomtom is very weird with its gps module, it keeps saying gps not found or signal lost etc and then I have to reselect other bluetooth and com 5 and even then sometimes I have to reinitialize the receiver before it is found. I always advocate the use of a wired gps if it is only required for vehicle use, it is less problematic, easy to configure and works 99.999999% of the time without problems.
If you run BT Manager and then check settings, it generally sets up as inbound com5 outbound com 6.
I have a Navman that behaved perfectly on Com 5 on TT3, on TT5 still behaves perfectly, but now uses Com 8 instead.
No idea why, don't really care that much -- it works.
I did buy the items from eBay and I am going to get back to the supplier (Polstar I believe) to see what I can fathom out.
Many thanks for all your advice, I have tried all options but still cannot get it to work so I will post a reply with the solution that works for me and hopefully it will work for others too.
No signal
Hi
the TomTom 5 has a new implementation, from the the TT3. It can manage the bluetooth connection. When you creat the connection with your pocket pc, by serial port, you must creat one connection of paired devices, as you created to your headset, bluethoot, of course. By the way, usually tt5 uses com 6 to connect with gps receivers.
The first time you configure your connection you must stay in position to receive signal from satelites, because its important to record all information from your gps receiver.
Regards
With regards to that marcusmodestus I think tonight, I will try and remove TomTom5 and delete my connection to the receiver and try installing again, from fresh.
Should I bond my reciever before or after I install? And should I run TomTom5 only with the bond in place?
bt gps
I bought one of these
set up as other cable on com5 but set baud rate at 38400 works fine 4 me
Success!
First, thank you all for helping me with this!
I have managed to successfully set it up now and here is the process...
Install TomTom5
Bond the device (I only had the option of Serial COM 7)
In TomTom5, change the preferences to use "Other Cable" and set the baud rate to 4800.
Magically I then get 5-6 satellites, a signal and an annoying American (which I will change to a nice english lady)
Thank you all again!
after hours of trial and error with tomtom5 and buzzmobile5.0 together with a xaiox wonde-xl bluetooth gps mouse (nemerix chipset) i learned the following:
it is recommended that you disable the gps manager of buzzmobile5.0 (not doing this has caused my device hang and auto soft reset some times). after that the following procedure worked for me:
1. pair your bluetooth gps device with your xda
2. assign a free outgoing com-port to that device (what com-port is best? please read text below.)
3. go to tomtom gps settings screen choose other bluetooth gps device
4. the assigned com-port number should appear in the next tomtom screen.
usually you should be done now and the connection should work, but i always had to delete the gps device in buzzmobiles bluetooth connection manager and had to re-pair it again, re-assign the com-port and re-start tomtom in order to get it work.
for any reason i then choosed to assign com8 as com-port for my gps mouse. and from this moment on tomtom5 was able to re-establish connections after switching of and on the gps or after switching xda on and off. i don't know what the exact reason is but choosing com8 was my solution to get tomtom5 working together with my gps on a comfortable way.
hope this helps others
regards
peter
I had this problem with Tomtom 5. No matter what I did it wouldn't work with my receiver.
I found that when I downloaded the 5.1 patch and installed it it worked fine with the GPS receiver set to COM6. Usually takes about 30 secs for the receiver to be found though. I think the update sorted out the Tomtom bluetooth support to a later version.
hi ...
how can i disable the gps manager of buzzmobile5.0?
thx mtc
settings --> system --> GPS
On the access tab uncheck the box
btw : I just saw that GPS hardware port shows com5 now. I'm sure I set both hard and software port to none cause somebody adviced this.
Anyway last week I didn't have to re-pair my gps in order for tomtom to find it ( which before I had to do every time I closed tt5). I've been messing in the registry to create extra com5 ports, maybe that's what caused it.
Anyways I now only have to switch on the gps and fire up tomtom and it immediately shows my position. Hope it will last..........

GPS+ TomTom5 problems with new Blutooth Stack

When I first tried installing this stack (see here: http://forum.xda-developers.com/viewtopic.php?t=33532 ) my exisiting bluetooth devices - a Jabra BT200 headset and Ambeon GPS both worked, just like that - without re-pairing, the latter with TomTom3.
However, in order to make stereo over A2DP to work I had to hard-reset and reinstall everything. Glad to say A2DP did work! However took opportunity to upgrade from TomTom3 to TomTom5.
Now I've re-paired with the GPS using the new stack, during which it asks if I want ti install a serial port. But it doesn't seem to be recognised by TomTom. And, if I go to the COM tab, and try and add a new port there is nothing in the drop down.
Any ideas?
The BT outgoing port on my magician is fixed at Com5. Maybe because I am using GPS Gate (a program to create virtual Com port so that U can open 2 or more GPS program at the same time), I don't have any problem before and after installing that BT stack.
Maybe U can try GPS Gate too. Just open Com5 in GPS gate and create an virtual port Com6. Then ask TT to connection to Com6.
Thanks but it's all OK
I used this great little free program
http://www.teletype.com/downloads/tty.zip
to test whether the GPS box was actually connected (but not recognised by TomTom) and it was - on COM5!
So I pocked around with TomTom some more, and found that it could pick up a signal on COM5 but if a signal was not there it reported that 'No GPS device' rather than 'No valid GPS signal.'
upgrade tomtom 5 to tomtom 5.1 :wink:
GideonS, did you get BT outgoing port to show up? If so, how? Like you, when I try to select one, it comes up with a blank selector box.
(Maybe I missed something in the thread, but the GPS Gate surely relies on diverting an existing port?)
thanks in advance!
Re: Thanks but it's all OK
GideonS said:
I used this great little free program
http://www.teletype.com/downloads/tty.zip
to test whether the GPS box was actually connected (but not recognised by TomTom) and it was - on COM5!
So I pocked around with TomTom some more, and found that it could pick up a signal on COM5 but if a signal was not there it reported that 'No GPS device' rather than 'No valid GPS signal.'
Click to expand...
Click to collapse
my tt5 5.21 (5430) + iberia plus 6.3.2 don't recognize my Socket GPS (http://www.socketcom.com/product/GP0820-521.asp)
i used that program you mencioned and it receives data on COM8 as defined by me
i'm at home and i never get a fix inside so i can't test if it's the same situation of the error messages switch
when i do, i'll post the result

T mobile MDA compact & GPS

hi all
i have had a right time trying in vain to get my t mobile MDA compact to work with the holox BT-321 GPS receiver. the reason i am having so much trouble is when i pair the devices, a small window flashes up and says "This bluetooth device supports serial port profile, would you like to create a bluetooth serial port for it?" the window box is labelled "bluetooth serial port COM5" of course i click yes, it asks me for the name, and i leave it what its called "BTGPS74R" and click finish, this leaves me on the main menu. in the com ports tab there is "new outgoing port" and "new incoming port" i click outgoing and next and low and behold there is nothing in the box whatsoever to select. i have checked all the boxes in my bluetooth settings for the 2 com ports.
the phone refuses to show any ports at all, i have flashed the imate jam rom 1.12 as i read that solved it, but it never, i have tried a bluetooth program called pocket bluetooth tools and this brings with it more com ports but they do not actually work by putting the ports in the drop down list, its still empty !!! also when i select say port 6/7/8 the small window flashes up saying "this device supports......" and then the pocket tools dissappears and its all back to nothing again.
i am at my wits end with it and i dont have a clue how to get this bluetooth port to actually show up so i can bond with my bluetooth GPS and make tom tom 5 work
thank you anyone who can help me
Dan
Hi,
i just resolved exactly the same problem on my mda compact.
I had to do a complete reset of the device...
Hi
I am having a similar problem. I have an orange SPV M1000 and the same bluetooth GPS device. It is paired in bluetooth devices. When I got to connect on Tom Tom 5 it can't pich up the receiver. I have tried all the different wired/bluetooth etc device settings in TT as it says to try wired if bluetooth doesnt work. But to no avail. I'm tempted to try different sat nav software. Any ideas? Let me know if your issue gets resolved!
cheers
AJ
Hi guys,
The options for new outgoing/incoming port creation are to connect to a device with which you haven't paired. My gps creates a com5 too, like all of yours & TT5 finds it pretty fast when I have it to use 'another bt gps' @ com5.
When you think a hard-reset will solve your problem, get yourself a good backup first. Cause sometimes you can restore that backup & the problem is still solved.
BTW does your gps support nmea protocol? TT can only handle nmea & that could be the cause when your gps is setup for external communication with another protocol.
Good luck M
Thanks for the reply
Hi there
I've attached the info from my receiver, looks like it should be ok.
Tom Tom only has connections on infrared, BT on COM6, Serial Cable on COM1, COM9:, COM2:, and Serial on USB
When I go to Start>Settings>Bluetooth settings there are options for bluetooth serial settings. These are non changable and if you check the boxes it will set Inbound Com port to COM4 and Outbound COM port to COM5.
These com ports dont seem to be options in Tom Tom 5 which confuses me.
So i download a program called BeeLineGPS which does a scan of all the ports and baud rates which I thought would be easier than the manual setup of TT5.
Try the com port options mentioned earlier with the BeeLine software and it still cant pick up the GPS device. Tried fiddling around for ages and still not working.
Do I need some kind of software for forwarding the ports so TT5 can see the device.
The advert for the device i bought promised me and easy set-up but this is being a pain
http://cgi.ebay.co.uk/32-Channel-Bl...03433467QQihZ018QQcategoryZ4668QQcmdZViewItem
All Fixed now. I upgraded the Rom to a newer version. After this the tom tom picked up that it was actually on port 5 which it wasnt doing before. Bobs your uncle

Bluetooth GPS Woes

Hi,
I seem to be having a problem with GPS bluetooth related connections with my Dopod 838 Pro.
Ive paired my Globalsat BT338 receiver and setup an outgoing serial port on my Dopod, and I can use Destinator 6 and TomTom 6 fine (for the time being).
The next day/time when I try to start the GPS applications, both programs report that they cant find the GPS signal/receiver even though its been correctly configured to work previously.
I then have to enter the Bluetooth settings to change and assign another outgoing serial port and reconfigure the GPS applications to the new serial port to work.
The programs and the GPS receiver worked fine with my old iPAQ hx4700 so its not a receiver or program issue.
I'm at my wits end and would appreciate any info on solving this problem.
Thanks in advance.
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Rik_053 said:
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Click to expand...
Click to collapse
Hi,
Ive been through this unpair / pair scenario more than a few times and Ive never used a secure com port connection.
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
njay22 said:
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
Click to expand...
Click to collapse
Hi,
The pairing has been done before any program was launched.
Im trying with both destinator 6 and tomtom 6
Bluetooth GPS Woes...
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
clearwave1 said:
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
Click to expand...
Click to collapse
Hi,
Both the bluetooth reciever and the software work fine and obtain a fix.
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
the gps reciver obtains a fix but the pda cant see it.
Destinator PN has an automatic reconnect tick box on the GPS Settings page. I don't know if D6 or TT have a similar thing. If so, make sure this box is ticked.
I use D PN with a Parrot CK3300 combined handsfree and GPS receiver, and after major stuffing around trying to get D PN set to the correct port initially, it has worked fine since.
Ive sorted the issue out and hopefully this will help others experiencing the same problem.
The problem was that although an outgoing serial port was setup, for some reason it was not mapped to the bluetooth device.
It just specified "COM9" instead of having the bluetooth device "BT338(COM9)" under the bluetooth COM Ports setting.
This seems to be the reason why when the device was unpaired/paired and a com port setup it worked for the time being. After the bluetooth device was disconnected the settings mapping to the device were not retained.
Rambler76,
I am looking to get a GPS unit for my Dopod 838Pro. Which of the two, Destinator or Tom Tom, do you like best?
I know where to get Destinator 6 in Sydney, where does one get Tom Tom 6?
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
killabeezz said:
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
hi,
what i mean to say is that i switch com ports.
the issue was resolved by mapping the com port to the bluetooth device.
Click to expand...
Click to collapse
Yes I understand what you have done but can I ask again :-
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Thanks,,
Tom Tom Woes
Hi,
I had the same problem until recently.
To fix I did the following:
Delete pair with GPS receiver,
Create new pair with GPS receiver (put in passkey 0000)
Tick the box for Serial Port
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Now open TomTom, Select Change Preferences, then Show GPS Status, then Configure, then Other Bluetooth Receiver, then Select COM 4.
Now TT works as it should - turning on and off Bluetooth on Open/Close, and no problems with needing to re-pair.
Previously I had always paired the BT GPS on COM 0 with Secure ticked. This worked the first time only, and I had to re-create the same pair each time I wanted to run the app.
Hope this helps some of you.
(btw I was using TT6 when I found the solution, but I imagine it would have worked for 5 too)
dopod bluetooth problems
Guys I have the same problem with my bluetooth and my dopod. It connects then disconnects.
I have also noticed that the systems unchecks the turn on bluetooth check box and the make this device discoverable to other devices.
Does anyone have any ideas?
Guys I just read this at another forum.
"The Dopod 838 pro and WM5 have chronic problems with the bluetooth stack, which is why everyone is waiting for the new ROM to appear, which will hopefully be WM6. HTC (manufacturers of Dopod 838 pro) announced that the new ROM will fix all of the known problems"
This I learn after having a car accident (minor) in my car playing with the bluetooth and trying to get it to work. Hutchison 3g should only be selling these with a warning.
I assume there is also a problem with the JasJam as they are the same phone.
Knight__Mayor said:
Hi,
To fix I did the following:
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Click to expand...
Click to collapse
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
dabs1 said:
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
Click to expand...
Click to collapse
yeah i recon its the screwy MS bluetooth stack, im interested to hear from anyone running tomtom on hermes with the widcomm bluetooth
Tomtom And Gps
I have found that the best cure for gps woes and pocket pc is to use GPS Gate. It make a virtual com port and will always be the same. I have used it always and never have problems connecting.
G

Categories

Resources