Related
:x i have been trying to get the bluetooth sync to work to no avail. i am using a 3com bluetooth usb adapter on my pc and card on my notebook. i am having problems with both when i try to synchronise. i can see my i-mate has been discovered and bonded; i can send files too. but i cannot synchronise. either there is a bug in the PDA software, or its really hard (needs a rocket scientist) to use!!! either way its dissappointing. can anyone help?
by the way my nokia and ericsson phones sync fine with my current setup.
I have the same problem using a toshiba portege 4010 with bluetooth built in, it works with my Nokia but not with the XDA i am using aytivesync 3.7.1
I would also like some help or ideas please
Thanks
John
Got bluetooth to work once
I got bluetooth to work only once using a Billionton USB Bluetooth adapter. The software is neat, but requires so much messing around with to get the PDA to actually synchronise in bluetooth mode. Unfortunately, I could not get it to work again. Should have documented what I did the first time.
After trying lots of times, it works. I sycronised a XDA2 in bluetooth mode.
There are a few important things
1. You first have to sychronise the XDA2 in USB Cradle to build a standard-partnership between desktop pc and XDA2.
2.remove the XDA2 from the Cradle.
3.look which com-port your bluetooth serial port is using
4.take these settings over to the active sync settings (must be exactly the same com port)
5. pair the two devices
6.start active sync on the XDA2 and sychronise via bluetooth
It works.....
i made a better description with screenshots (in german) but i don't know how to post it.
I use a toshiba laptop with bluetooth built in, but when i scan the available bluetooth things in the XDA 2 it only finds "voice gateway" and "SSA" or something like that, there is no serial port listed, when i scan a phone (nokia) it finds "dun" "serial port" "fax" etc etc.
So i cant connect my XDA2 as the only profiles it seems to have are Voice gateway and some SSA thing, so as there is no serial port listed i cant use activesync, i have bonded with both the voice and SSA thing to com ports from 5 to 9 and get a connection, but as its not a serial port it will not work with activesync.
Sorry for my terrible description of the problem, but if yours works i am sur e it will make sence to you
Thanks
John
Your right ! The XDA2 provides no serial port profile to my Bluetooth stick too. And thats why the Bluetooth GPS Receiver doesn't work.
I know this sounds strange, but with Active Sync Bluetooth definitely works.
Yes I finally got it to work a couple of days ago with a certain type of bluetooth usb adapter and software. All I can say, is that bluetooth is not very user friendly!!!! Activesync should have it show up just as it shows "infrared" in the connection settings. This will make it very easy to select it. In this day and age, you cannot expect a technology to be successful from mass usage if it is not totally idiot proof. BLUETOOTH is not.... WIFI will rule!!!!
Hi so have you bonded to the "ssa" profile, and then what ever com port you used you then changed activesync to use this port and it then works, because i tried this and it done not work.
I also have a tomtom bluetooth that a friend is borrowing, but by the looks of it there is no point in getting it back as if there is no serial port on the available using bluetooth that will not work either
Thanks
John
try this link. it may help u set up your bluetooth with active sync - http://www.bluetoothnews.com/features/ActiveSync.htm
@applecom
No. You just have to pair the Devices. Don't connect to any Profile.
Pair them and then start Active Sync from the XDA 2 and connect with bluetooth.
activesync and bluetooth with xda II
start > settings > system > bluetooth settings > Activesync over blutooth (START)
Nutty but there you go.
XDA II Bluetooth ActiveSync
I noted if you add or change the registry will work even better :
\HLKM\SOFT\Microsoft\Bluetooth\Activesync
IsBTASsetup from 0 to 1
Hi
I have changed the registry like you said, But how dose it work better, the only problems i have are when i ask activesync on the XDA to connect over BT it oftern trys and says port in use, i just retry a few times and it works. After doing the reg edit it did connect first time, but is this what you ment by "its works better"
Thanks
John
As this my first ever post, I don't want to come over as smug, but I took delivery of my XDA 2 today and it synced using bluetooth after about 25 minutes of 'messing'!
All I did was delete all the bonding between the PC and the XDA and told it to sync via bluetooth, initiating from the XDA, I thought that it had failed...but then the XDA sprang to life and 'Bob was my uncle'!!
Very impressed with my XDA 2, having used an XDA for about 8 months.
Andy.
Bluetooth Sync
What I meant was it has become easier to get XDA II sync via bluetooth. Please note that you have to unpair your PC first then change the registry and pair again. If your PC's Bluetooth dongle support Headset profile ( I used anycom USB220 which has this profile) you will see your XDA II asking you if you want Headset profile added and Activesync screen for bluetooth appeared as well. Changing the registry will always make the sync work is what i noted. Seems like XDA II Bluetooth supports many profile just that dont know how to make it works.
Bluetooth Activesync problems
I'm on the verge of giving up on this! Think I should stick to USB sync...here goes...
I've tried the tricks mentioned in the forum to try to get my XDA II to sync via bluetooth with my Sony VAIO laptop (it has built-in bluetooth). I can get the two devices to bond (I enter the PIN number on both the laptop and XDA and it succeeds) but then I try to run the Bluetooth Activesync setup (in Settings-->Bluetooth Settings on the XDA) I get an error message every time that says "Please bond with other Bluetooth device which supports serial port or Activesync profile as your Activesync partner!"
I thought I already HAD bonded the devices? Any ideas?
Cheers
Carlton
Finally sorted it out. Delete the partnership that you already have. Start from start>settings>system>Bluetooth Settings. When you clik start, then pair your device again. After the pairing, you will get the message that Bluetooth Active Sync is now ready.
Still no joy
Thanks for your help Merc.
I tried doing exactly what you suggested but still doesn't work. This is what happens:
I deleted the existing bond on both XDA II and PC.
I went to start>settings>system>Bluetooth Settings and clicked on Start. This gave me the message "Please bond with other Bluetooth device which supports serial port or Activesync profile as your Activesync partner!" like before, then automatically opened the Bluetooth connections control panel in the "Mode" pane. I chose 'Discoverable' and clicked OK. I then went to my PC and used the Wireless Link control panel and clicked 'Add' (to run Bluetooth connection wizard) which searched for devices. It found my XDA II and I entered the passkey on both XDAII and PC (same passkey on each).
The Bluetooth connection wizard then told me that the XDAII was offering DUN (dial up networking) services. I selected this and then clicked next. Was I supposed to select this (actually, it made no difference when I tried again without selecting!).
The wizard completed and both the PC and XDAII notified me that the bond was successful. I then waited and waited for something else to 'happen' (like a message to say that Bluetooth Active Sync is now ready.) but nothing happened. I gave it a couple of minutes.
I went to Activesync on the XDA and tried the 'connct with Bluetooth' just in case it had worked, but nothing happened. I went to Activesync on the PC and tried using a different COM port for infrared/serial links (as I assume this is what bluetooth uses) but no joy. I only had COM3 and COM4 showing in the connection settings in activesync, which surprised me as I thought there would be more.
That's it. I tried 3 times but still no luck. Any other ideas are greatly appreciated!
Cheers
Carlton
The
Your procedure is just like mine. But I used "On" and discovered the PC from the PDA. Do not use "Discoverable". Let me hear if you have any luck
The only way I have got it to work is assigning the bluetooth serial port to COM 6. Then set Activesync on the desktop to COM 6.
Any other COM port just won't work. Anybody else got it working on a different bluetooth COM port?
xdaguru
hey all, i'm having some difficulties getting my jam to sync with active sync! both laptop and jam have bluetooth and can see each other but the problem is everytime i click sync via bluetooth my jam does nothing!
i've download both bluetooth patches on this foru and neither have helped?!
can anyone help or at least tell me where im going wrong
thanks in advance!
You should try downloading Pocket bluetooth Tools version 1.0.1.2.
Install this program on your jam. After that you should see to it that the comport active sync wants to use is free (set the port in active sync/connection settings). Remove all pairs. Pair again using your jam to find the laptop. After filling in the passwords for pairing a screen should pop up on your jam with a few profiles, there you should select Active Sync, and it will work hopefully. It is possible that I have made a mistake since it has been a long time since I've done this. Goodluck!
If you don't explain the actions you have taken in your attempts to sync your
device via bluetooth, only a psychic wil be able to tell you where you went wrong.
But have a look at the following link, it might be of help to you since the Active sync BT settings are everything but intuitive:
http://www.amset.info/pocketpc/sync-bluetooth.asp
If you don't explain the actions you have taken in your attempts to sync your
device via bluetooth, only a psychic wil be able to tell you where you went wrong.
But have a look at the following link, it might be of help to you since the Active sync BT settings are everything but intuitive:
http://www.amset.info/pocketpc/sync-bluetooth.asp
boh113 said:
hey all, i'm having some difficulties getting my jam to sync with active sync! both laptop and jam have bluetooth and can see each other but the problem is everytime i click sync via bluetooth my jam does nothing!
i've download both bluetooth patches on this foru and neither have helped?!
can anyone help or at least tell me where im going wrong
thanks in advance!
Click to expand...
Click to collapse
I found 'bluetooth com port' in this forum & it helps in doing Sync via BT. Do a search. I'll suggest you to read the manual. if you don't have 1 search in www.seeo2.com or from your phone manufacturer site. I'll read the FAQ or Knowledge base before seeking for help in the event i don't understand the 'manual/FAQ'
Hi
I have read through literally hunderds of pages of GPS stuff to do with mini. I have read some things that are true and some that aren't and am now confused.
I installed Tomtom 5.0 onto my Mini S. It went on fine. Maps installed fine. I went into 'satellites - configure' part and couldn't find my GPS on any of the settings. I am almost sure my GPS receiver isn't bluetooth. I know the baud should be 4800, but otherwise I am not sure. My dad has the same recieve but uses his with an IPAQ and it worked first time. I have tried my receiver with his ipaq and the receiver works fine so that eliminates that posibility.
Here is my receiver and the blurb that comes with it.
http://www.evermoregps.ca/
GM-R700 GPS receiver
(third one down.)
The mouse-shape GPS receiver is design for PC and PDA applications. With WAAS/EGNOS channels, EverMore can give you more accurate direction and position. Compact Flash module is also available now.
I selected 'Other NMEA GPS receiver' and tried all of those. Then went through the bluetooth equivelent just in case. None of them pick my receiver up.
I then read somewhere that version 6 of Tomtom wouldn't work on my XDA mini. I downloaded 5.2 and tried it with that. I had read that this allowed 'port 7' to work. I couldn't get my map to work with 5.2 even though I spent ages on it. Eventually I tried Tomtom 6.0. As I mentioned earlier, someone had said that it wouldn't work on an XDA, but this is false as I got it working straight away. The map also installed fine and once I activated it things seemed ok. I presumed that the port 7 would now come as an option. It didn't. I am still at the same place. I believe that the port 7 thing may be a bluetooth only thing but I am not sure. I am not great at GPSbut know my way around an IPAQ pretty well. I am new to my phone so chances are there is some gateway or something that I haven't enabled etc, but I am at the end of what I know.
If anyone can help me out at all I would be eternally greatful. So far I have spent a good 20 hours getting the bloody thing working and I am about to lose the will to live.
I have used the search option on the site, but it seems everyone has BT GPS, and none of the posts seem relevant to my problem. If I have missed a post then I am sorry, but there are a fair few posts on the site now.
Thanks in advance,
Woody.
bluetooth
you have to pair your gps receiver with your phone in bluetooth settings give it com ports then go into tomtom then into show gps status then configurethen other bluetooth gps receiver then pick your com port hope this helps
jay05 said:
you have to pair your gps receiver with your phone in bluetooth settings give it com ports then go into tomtom then into show gps status then configurethen other bluetooth gps receiver then pick your com port hope this helps
Click to expand...
Click to collapse
Do I have to do this even though it isn't a bluetooth device?
Even when I enabled com 7 on bluetooth settings, comm 7 didn't appear on 'Select your GPS receiver' on Tomtom.
I will try it anyway, and thanks for the speedy response.
sorry
i have give you wrong advice i thought gps recever wash bluetooth you should try going into on your phone settings, connections ,beam ,and un tick receive all in coming beams as these frees up the com port 7 on xda1.YOU WILL HAVE TO RECONFIGURE SETTINGS IN TOMTOM GPS STATUS FOR WIRED GPS RECEVER. SORRY FOR LAST POST HOPE THIS HELPS ps i got gps recever recever off ebay was meant to work on my xda1 but did not it was for ipaq the connector was the same but wiring was wrong hope this helps
Woody, first of all I couldn't understand that which GPS device have you got as you have mentioned 3rd down on that webpage, anyway I have the attached the picture of one of the device named "GM-R700", if this is the right device which you have then this is a serial cabled GPS device which connect to the device via cradle, not via Bluetooth, if I am right then bluetooth chapter is closed, we are going to talk about the cable GPS device.
If it is the right device then how are you connecting the GPS device to the XDA, does the GPS device came with the cradle and the car charger? (it must be).
Find the attached word file for a sequential instructions, I have just made it for you and others who are still stuck to make their TomTom work.
GoodLuck & let me know.
Sidd
Sidd, your attached documents refuse to open!, I am not too sure that you can connect a wired GPS to this type of phone, it simply won't work, the only option is Bluetooth for the Wizzard. In the case of the IIi and IIs phones they had a true serial port that could be used - Mike
Try these attached files as I have zipped them on a normal compression.
I think ""GuinUK (1st post)"" hasn't mention his/her device, but the GPS he/she mentioned is a serial device.
Sidd
I am pretty sure it is a Mini S he is trying to get to work with the cabled GPS receiver, it simply will not work - the device doesn't have a serial port to connect equipment like this to. The Mini S is Bluetooth only for GPS AFAIK - Mike
sidd said:
Woody, first of all I couldn't understand that which GPS device have you got as you have mentioned 3rd down on that webpage, anyway I have the attached the picture of one of the device named "GM-R700", if this is the right device which you have then this is a serial cabled GPS device which connect to the device via cradle, not via Bluetooth, if I am right then bluetooth chapter is closed, we are going to talk about the cable GPS device.
If it is the right device then how are you connecting the GPS device to the XDA, does the GPS device came with the cradle and the car charger? (it must be).
Find the attached word file for a sequential instructions, I have just made it for you and others who are still stuck to make their TomTom work.
GoodLuck & let me know.
Sidd
Click to expand...
Click to collapse
Thanks for your reply. This is indeed the right GPS. Sorry for any confusion there. I am about to try what you have written. I have indeed got a cradle, and a converter which makes my Ps2 GPS fit into the socket.
I will get back to you with how I got on.
Thanks again for the help, at least I know for sure it isn't BT before I start.
Woody
mikealder said:
I am pretty sure it is a Mini S he is trying to get to work with the cabled GPS receiver, it simply will not work - the device doesn't have a serial port to connect equipment like this to. The Mini S is Bluetooth only for GPS AFAIK - Mike
Click to expand...
Click to collapse
OK I got the download working from Sidd, thanks. I ran through all the steps you had mentioned. The problem I had is that I don't get the option of 'serial cable blah blah', mine just says 'Serial port'.
My phone is a Mini S. Perhaps this is the reason why. My friend has a bluetooth model, and I got that working fine so I guess if this last attempt doesn't work I will just buy another GPS. It isn't like they are expensive in truth.
Thanks everyone for the help, and sorry for my delay in posting but it being Xmas and all.
Cheers
Woody
If u r going for a bluetooth gps device then keep one thing in mind that u might find difficulty in searching of the proper bluetooth com port. Soltution is to download the TomTom version 5.2 prior to connect ur device.
GoodLuck & let me know
Sidd
Fantastic post
Thanks Sidd, your word doc (Serial COM Port setting to setup TomTom.doc) worked a treat, two mins and I'm up and running. I'm using spv m1500 (same as xda 2) with a cheap unbranded cabled gps unit i got from fleabay and TomTom 5.2. Thanks again.
Can I re-iterate for the benefit of others reading this post, the newer XDA device (equipped with a mini USB connection point) cannot be used with a wired GPS unit, this includes the Mini-S, Exec, Orbit etc. The older devices IIs, IIi etc all require the Receive all beams to be turned of to free up the serial port for use by the wired GPS.
If your device has a mini USB connector your only option is Bluetooth for GPS - Mike
Doc114 said:
Thanks Sidd, your word doc (Serial COM Port setting to setup TomTom.doc) worked a treat, two mins and I'm up and running. I'm using spv m1500 (same as xda 2) with a cheap unbranded cabled gps unit i got from fleabay and TomTom 5.2. Thanks again.
Click to expand...
Click to collapse
No problem Doc114 my pleasure, any way I am also going to upload something new on the FTP (check in: ftp://ftp.xda-developers.com/Uploads/Software/) with another brief instruction manual, enjoy the new one, you know what I mean (My name would be included in the file name, so you can recognise it easily).
I will also make one illustrated instruction for a bluetooth GPS setting whenever got a device.
Sidd
hello every 1. I have a BA running windows mob 6.1 pro and everything is working fine except t e fact that when i put the device on standby, it is always turning itself on again. does this happen to anyone? thanks
hi
any test?what do mean?
Zero|Cool said:
hello every 1. I have a BA running windows mob 6.1 pro and everything is working fine except t e fact that when i put the device on standby, it is always turning itself on again. does this happen to anyone? thanks
Click to expand...
Click to collapse
which ROM do you have?
Do you happen to have BigMike bluetooth running?
standy..you mean you press the power button and the screen goes off, right? And then it turns on by itself? Did you check if your bluetooth is on? Because I experienced this too before, if I left the bluetooth on and I turn off (stand by) the BA after a while it will turn on itself. Hope this helps. Cheers.
Try going through your power management under settings.
You might have tick a few things there.
I was getting this trouble too!
As Resident evil... on nights my device wakes up and begins screaming STARS!!!!
I just call Claire redfield and Alice and they burn on its head! PUMMM!
jajajaj
Well... check out your settings if you have a program runing under... and it needs conections via BT, Wi-fi or GPRS... your device gonna wakes up trying to get conection all the ways it can... if nothing is runing behind maybe was a bad flash... reflash it...
Hope all we can help you...
We are like a squadron supporting forces... Huh im playing too much Acecombat 5....
It could either be Bluetooth running and also it could be some appointment/message turning your device on. Also, do you have your device cradled? ActiveSync (if connected to PC) will turn your device on to sync.
Hope this helps
red_hanks said:
standy..you mean you press the power button and the screen goes off, right? And then it turns on by itself? Did you check if your bluetooth is on? Because I experienced this too before, if I left the bluetooth on and I turn off (stand by) the BA after a while it will turn on itself. Hope this helps. Cheers.
Click to expand...
Click to collapse
It's exaclty that. I read somewhere it has something to do with the bluetooth stack, I turned off BT and it stopped lol However I need BT always on as I use an external sirf star 3 gps and I pair up the mobile phone with my car. Can anyone tell me how to fix this? Tks
Zero|Cool said:
It's exaclty that. I read somewhere it has something to do with the bluetooth stack, I turned off BT and it stopped lol However I need BT always on as I use an external sirf star 3 gps and I pair up the mobile phone with my car. Can anyone tell me how to fix this? Tks
Click to expand...
Click to collapse
There is no fix. Since WM5, the BT driver requires that it be turned on periodically or else it turns itself off. All ROM cookers (AFAIK) use the big mike fix driver to keep the BT alive.
motisu said:
There is no fix. Since WM5, the BT driver requires that it be turned on periodically or else it turns itself off. All ROM cookers (AFAIK) use the big mike fix driver to keep the BT alive.
Click to expand...
Click to collapse
I read somewhere that if you installed another BT stack that eventually it would solve the problem? Is this true?
ok there is fix but i do not advice you to use it if you use BT handsfree - because with original driver BT turns off when device get in standby and this one keeps it working
you can install S2U2 and set:
Lock when device wakes up: ON
Power Off in: 5s (this is the minimum).
this is not a solution, but more like a workaround...this works for me well...
I've been using the Belkin Bluetooth Car Hands-Free Kit for the last year with my Nexus 4.
http://www.amazon.com/Belkin-Bluetooth-Hands-Free-BlackBerry-Smartphones/dp/B004CLYJ2I
For the most part it has worked great. However, my new Note 3 will not connect automatically to the device, I always have to turn the screen on and select the bluetooth device to connect to it. My Nexus 4 would simply connect to it automatically if the bluetooth was switched on.
Any ideas?
hfuizo said:
I've been using the Belkin Bluetooth Car Hands-Free Kit for the last year with my Nexus 4.
http://www.amazon.com/Belkin-Bluetooth-Hands-Free-BlackBerry-Smartphones/dp/B004CLYJ2I
For the most part it has worked great. However, my new Note 3 will not connect automatically to the device, I always have to turn the screen on and select the bluetooth device to connect to it. My Nexus 4 would simply connect to it automatically if the bluetooth was switched on.
Any ideas?
Click to expand...
Click to collapse
I had similar issues with my bluetooth headset. When I would press the connect button on my bluetooth it wouldn't automatically connect, and the only solution I found was re-arranging my quick toggles in the notification bar so when I pull it down I can quickly access bluetooth settings and devices.
Yep am having problems with note 3 bluetooth. For a top of range phone, this bluetooth is crap. 2 headsets works when it wants and 6 works wagons only works in some! Am surprised no one else as commented on the bluetooth
Sent from my SM-N9005 using xda premium
I had the same issue that my N3 didn't connect automatically to my BT-devices. I stumbled over a thread where I found some one else having the same issue who recommended the app "Bluetooth auto connect". I downloaded the app and now it just works. If you have the BT-scan dialog enabled, you see how it switches between the different paired devices in the list until it locks on to the one that's in range.
If you don't like that dialog, you can disable it using wanam (I think). Hope this helps.
Mikegrmn said:
I had the same issue that my N3 didn't connect automatically to my BT-devices. I stumbled over a thread where I found some one else having the same issue who recommended the app "Bluetooth auto connect". I downloaded the app and now it just works. If you have the BT-scan dialog enabled, you see how it switches between the different paired devices in the list until it locks on to the one that's in range.
If you don't like that dialog, you can disable it using wanam (I think). Hope this helps.
Click to expand...
Click to collapse
Thanks for the suggestion, I'll give it a try. Does this app have any affect on your battery life?
hfuizo said:
Thanks for the suggestion, I'll give it a try. Does this app have any affect on your battery life?
Click to expand...
Click to collapse
Not for me. But I may not be the average user. I'm getting 3 days of battery life out of my N3. I only turn wireless (3g / wifi) on when I need it and do the same with BT. But I found it really inconvenient to have to select my connected BT device. For switching BT on and off, I use tasker. I have a setting that checks for the music app of my choice, and when I start it and have no headphones connected, tasker turns on BT.