Cannot connect for an unknown reason! - MDA II, XDA II, 2060 General

Hello,
Hope someone can help me out.
I am able to connect to mobile.o2.co.uk and btmobile.bt.com OK.
However while trying to connect to another APN which is also enabled on my account i get the error message:
Cannot connect for an unknown reason. To check your settings, blah blah blah.
Software reset - Done
Created new connection - Done
Modem - Cellular Line (GPRS)
Server-assigned IP addy
Use software compression - try checked and unchecked
Use IP header compression - try checked and unchecked
Server assigned addresses
GPRS settings - CHAP auth
Class 8 (4R1T)
Check with SP and they assure me that I am enabled for all the above APN's.
Try the same SIM in a Aircard 750 on the problem APN and it connects fine.
Any advice would be much appreciated.
Rgds,
O'Rourke

Related

wi fi - cannot get IP address

well, i am still looking for an answer to my problem, maybe here i will find it...
i have the San Disk WIFI SD card for my I mate.
i have downloaded the driver of Socket, but still, i can connect to the hotspot but i cannot use the web.
because i am not an expert in WIFI i have asked one's opinion.
he asked me to check some details (i am enclosing them here).
he told me that my problem is not with my wifi card or in the network.
he told me that from unknown reason, i don't get an IP address.
can someone please lett me what can i do?
Guy
& here are the details:
associated ssid: hot spot
associated bssid: 00:02:2D:3C:7D:8E
Chanel 6
Nic
Beacon: 100 kusec
Atim: 0 kusec
frequency:2,457,000 khz chanel 10
Authentication: open
Wep: disabled
mode: infrastructure
Type Dss
supported rates: 1,2,5.5,11 Mbps
IP Address 0.0.0.0
Subnet Mask: 0.0.0.0
Gatewayit was empty)
DNS Server 10.0.0.138
DHCP Server: 192.168.1.1.
Primary Wins Server: (it was empty)
Secondary Wins server: (it was empty)
guy-k
I have also had this problem with my Socket wifi card on my XDAII using the latest version of the socket driver. I have had to revert to version of the Socket driver (142D) because of this problem. Version 142D works fine, but doesn't have such a fancy interface as the new version!
If you need a copy of this driver, PM me.
Paul
It didn't help
Hi,
well i have tried the old version, but nothing.
i still cannot obtain ip.
any ideas?
Guy
[/img]
I Have had the same problem and gave my M1000 a fixt IP adres yours should be something like 192.168.1.12 or at least something else as what your pc has further I always setup the nameservers you can find them to type in a dosbox ipconfig/all the DNS servers there you have to steup in the configuration of the networkcard from your phone , which can be found at settings /connextions/networkadapters there you will find the Sandiskcard just click on it and the settings for it will apear.
Now you should have connextion then still your PDA don't now that it has to use the networkadapter to get a connextion so you have to tell it to him at conections/settings/select network and there select twice work Network, this is only for your internetconnextion true your browser but email needs a other setting which you can find at your email client/tools/options/accounts/your emailaccount/next/next/next/options/there you selct work network/next finnish and now you should have full internetacces with your phone true your accespoint, if you want to use your phone to get your email just change the settings from work to providor internet, it seems to be a little complcated but it gives me at least a verry stabele internetconnection
Sucses with it
Greetz Willem
I get that message when im too far from the hotspot

ActiveSync - "Unable to obtain a server-assigned IP&quo

Hiya.
When I'm syncing my Wizard (O2 Mini S) with XP SP2 via the USB cable, I've started getting a dialog popup upon connection which says:
Code:
Pocket PC Networking
Unable to obtain a server-assigned IP address. Try again later or enter an IP address in network settings.
I click ok, and the box disappears, and it seems to sync okay. So it's not a big problem, but I just wondered what exactly it's complaining about.
Cheers muchly.
Rolo.
I got that, too. No idea why, though.
Me to although sync works fine??
i think it's referring to internet through activesync. i was getting the same thing when trying to connect to my router so i went to network adapters in network cards and set a static ip for my device.
in the network adapters page there's an adapter called asyncmac.... maybe if u set a static ip for that adapter u'll stop getting that error
fone_fanatic said:
i think it's referring to internet through activesync. i was getting the same thing when trying to connect to my router so i went to network adapters in network cards and set a static ip for my device.
in the network adapters page there's an adapter called asyncmac.... maybe if u set a static ip for that adapter u'll stop getting that error
Click to expand...
Click to collapse
I have the same problem. Setting the asyncmac to static IP did not help.
Anyone that has another suggestion on how to solve this.
My kjam started to do this. I know what I did: I went into the Settings/Connections/Network Cards/Network Adaptors/Remote-NDIS Host and it would not let me out without setting something up so I set it to "User server assigned IP address". I then started to get this message.
Something killed the cat...
I then changed it to "Use specific IP address": 169.254.2.1/255.255.0.0
as was listed on another site. The proble went away..OTOH, I'm not
sure what I messed up in doing this..everything seems to be working.
-Michael.
still got problem
mjohns said:
My kjam started to do this. I know what I did: I went into the Settings/Connections/Network Cards/Network Adaptors/Remote-NDIS Host and it would not let me out without setting something up so I set it to "User server assigned IP address". I then started to get this message.
Something killed the cat...
I then changed it to "Use specific IP address": 169.254.2.1/255.255.0.0
as was listed on another site. The proble went away..OTOH, I'm not
sure what I messed up in doing this..everything seems to be working.
-Michael.
Click to expand...
Click to collapse
I tried the same but it seems I still got problem....is the IP number you reported the same for everyone?
I took the listed IP on blind faith... One other thing I've changed in activesync is to set up a dummy server so that it doesn't start up by itself as quoted below from howard-forums at http://65.254.44.186/showpost.php?p=6156473&postcount=3
I ddid this and the ip change at the same time. Might be worth a try.
-Michael.
Quoted of post by Koksie on Howard-forums:
I had the same on my T-Mobile Vario untill I did the following: In ActiveSync go to menu-server configuration. Put in a server name ( just invent one, does not have to be a real one) and tap next. Leave everything empty and tap "advanced". Do not change the values in the boxes and tap next. leave all the boxes empty and tap finish. Then go to Menu-Schedule and put both boxes on manual. On my Vario it worked, ActiveSync does no longer activate itself every x minutes to try sunchronizing with an exchange server, which is what causes the spontaneous periodical activation of Active Sync.

WiFi Connecttion

Hi Everybody!
I'm looking for some help with connecting to my home WiFi.
In settings, netwok card, I can see my home network.
I use a netgear router with WEP security.
I just can't seem to connect and I can't seem how to input my WEP acces passkey too?
Thanks for any replies
{>
In settings, wireless lan, advanced it states that I am connected to the network, but I still can't connect when using IE?
the message reads : " U~nable to obtain a server assigned IP address . . . etc"
Do you have DHCP enabled on the wireless router? Have you used the wireless network with another device?
Mmm, very good question!
The answer is "don't know". Will check and let you know Syn.
Will start again.now that I have managed to "flash my rom"
Well this is what I have :
Wireless Network
Name (SSID):
Region: --- Select Region ---AfricaAsiaAustraliaCanadaEuropeFranceIsraelJapanMexicoSouth AmericaUnited States
Channel: 01020304050607080910111213
Wireless Access Point
Enable Wireless Access Point
Allow Broadcast of Name (SSID)
Wireless Card Access List
Security Encryption (WEP)
Authentication Type: AutomaticOpen SystemShared Key
Encryption Strength: Disable64bit128bit
I have added the device to my wireless network list with the MAC address
Signal is VERY GOOD!!!
Am I missing out son some settings?
{>
I've tried to set up a new connection as Internet Explorer tells me it cannot connect with the current settings?
What settings do I need?
I have entered the WEP key, and I don't use passwords on my wifi system??
{<
Do I need an IP address?
Scutter
First things first, forget the PDA for few moments and lets establish what is going on with your AP. The question that [sYn] has asked is very important - do you have DHCP enabled on the AP. The answer you posted is meaningless as it only shows the options and not the current config. Interrogate the AP and look for where the LAN side DCHP option is and make sure it is set to ENABLE or ON or whatever positive indication is used.
Once you are sure this is configured (ideally tested with a PC) then go get your PDA and try connecting again. If it still doesn't work disable all the security and encryption settings and turn off that stupid MAC address authentication which, by the way, is pointless. If needs be do a factory reset on the AP. With no security enabled try conecting the PDA. It more than likely will connect now. Once it does start building up your security one layer at a time making sure you test at each stage. Can I suggest that you forget WAP and MAC authentication and use a WPA Pre-Shared Key instead as this provides bucket loads more security.
Hope this helps.
JT, thanks for all your help!
I use a netgear router. Whilst awaiting a reply here I did a bit of research and took of the security of my router. I then connected my device using a shared key (I have always had this) and then put the security back on.
I had to reconnect my laptop too. I think the reason isthat the router was set for an automatic setting and I chaned this to an open system.
THANKS AGAIN FOR YOUR HELP !!!
{>

SPV M3100 (TyTn). WiFi wont connect to my router.

I have a SPV M3100 (TyTn, I think) but I cant get it to connect using WiFi to my wireless router. I can go into 'Configure Wireless Networks' and tell it to connect to my router, all the settings are correct, but all it does is try to connect and fail, and no error message comes up.
Does anyone know how I could fix this problem?
Thanks,
Sebastian
it might help if you state what rom your are using and what protection the router is using? I know there are many threads discussing this issue with WM6 using WPA. Have you tried connecting with no encryption? If so can you connect.
Sorry, the ROM version is: 1.23.61.4, date: 7/13/06
It is running WM5 PocketPC. Encryption is WEP. No I havent tried no encryption. I will after when I get home.
Sebastian
OK, I've tried without encryption, and I've fiddled about with the settings but it still doesn't work.
Each time I tell it to connect it says 'Connecting' for about a second then says 'Unavailable' for a few seconds, then back to 'Available', untill I next tell it to connect.
Any suggestions?
thanks,
sebastian
if it use mac filtering the mac of the tytn need to be added to the lists of mac's the router wanna talk to
that's not the problem either, sorry
Couple of things (I'm running WM6 on my M3100, so WM5 is a bit of distant memory ) you could look at.....
First, does your router use DHCP to issue IP addresses? if not, you'll need to set the phone with a static IP. To do that, go to Start / Settings / Connections tab / Wi-Fi / Network adapters tab, make sure it says "connect to the internet" then tap the "802.11" network adapter, tap "use specific ip address", fill one in and "ok" your way back out.
Second, in Start / Settings / Connections tab / Wi-Fi / Wireless tab, tap and hold your "unavailable" wireless connection then choose Edit. Make sure the "connects to" box says Internet. Also, if your router doesn't broadcast its' SSID, (on WM6 at least) tick the box that says "this is a hidden network", then go next, next finish (making sure the authentication and encryption types match your router config!!).
Hope this helps,
Mark.
I have now been through every intricate detail within settings, and still to no avail. One (possibly) good thing did come out of it though - an error message.
I got it when going to create a new WiFi connection and clicking on the 802.1x tab, it says:
"Cannot log on to the wireless network. This network requires a personal certificate to positively identify you."
I made sure I inputted the network key correctly and all the encryption settings were right.
Please tell me that helps solve the problem! lol
btw, the router is a D-Link DSL-604+, just incase that helps anybody solve the problem.
sebastian
If you're getting certificate errors, it sounds as though you've ticked the setting in the phone's wireless config that says something like "IEEE 802.1x network access" and selected "smart card or certificate".
Go back in to the wireless config, tap and hold the "unavailable" network, then select Edit. Go through - next, next and the authentication is on the last page IIRC.....just untick the box, tap finish and you should be away!!
Cheers,
Mark.
It WORKS!!
I forgot to untick 'The network key is automatically provided' and tried to connect, and it now works
I'll just kiss goodbye to my battery life now
Thanks for everyone who has helped me.
Sebastian
My ATT Tilt wont connect to my D-Link Wireless N Router.. does the Tilt not work on N routers?

Wi-fi authenticated but not working.

Hi, I recently got my first WM device with Wi-fi (T-Mobile Vario III). I've been trying to get Wi-fi working with my network, but it doesn't seem to want to play!
I'm using WPA with AES, and using 802.1X authentication (my access point connects to my FreeRADIUS server). The same Linux box that runs the RADIUS server also runs the DHCP server for the network.
I'm using EAP-TLS authentication for the network (I based the setup for the network on this http://wiki.freeradius.org/WPA_HOWTO).
I've installed my root CA cert and intermediate CA cert (not covered in the howto, but I prefer to use and intermediate 'working' CA "just in case" ) on the Vario III. I also generated a client certificate/key for the Vario and installed it successfully on the device.
I then went on to Settings->Connections->Wi-fi and chose to add a new connection and did the following:
1) Entered the network name (SSID) and selected the "This is a hidden network" checkbox (also set it to be connecting to "The Internet" - I had to go to the network adapters tab as well and set the wi-fi adapter to be "The Internet" from "Work")
2) Selected authentication to be WPA and Data Encryption to be AES.
3) Selected the EAP type to be "Smart Card or Certificate" and went to properties. In the properties box I was shown the only personal certificate I have (i.e. the client certificate that I just installed for network authentication)
I then connect to the network, and get a User Name/Domain dialog (I don't really understand why). This is pre-populated with my name, but I've tried the following in this box (the only way to get it back after having entered something appears to be a hard reset - but there must be another way?):
1) The default provided (i.e. my name)
2) The CN for the personal certificate
3) Nothing
In each case I leave the 'Domain' field empty. With all three of the above the FreeRADIUS server reports successful authentication and the Vario III appears to be connected to the network. If I go to Settings->Connections->Wireless LAN, on the Advanced tab it says that it is 'Associated to network'
The problem is that even though I'm connected to the network and have been allocated an IP address (I have my DHCP server assign a specific IP address to specific MAC addresses), I cannot connect to any websites - I don't have anything over than Pocket IE installed on the device yet. I can't even connect to the management page for the AP that the Vario III is connected to.
This setup works perfectly from a WinXP box.
Has anyone got any ideas on what could be going wrong, or advise on how I can troubleshoot? Anyone know if there are logs stored on the device for wireless connectivity (either a log file or something like the event viewer in XP)?
Any help appreciated.
Thanks
Hi,
I have WiFi setup and running on my device, XDA Orbit, using WPA and AES.
First of all, whilst inside the Network Adapters tab, make sure that:
'My network card connects to': WORK
Secondly, in 'tap adapter to modify settings' you'll need to click on a particular network adapter card inorder to configure it.
In my case, I chose the SDIO WLAN Wireless Adapter. I then clicked the radio button 'Use specific IP address' and configured the IP address of my device, exactly as it is assigned in my Netgear wireless router.
If you haven't assigned a specific IP address to your device, just click the radio button next to 'Use server-assigned IP address'.
On the 'Advanced' tab of Wireless LAN, mine also reads 'Associated to network' as the status. It also has the MAC address of my device, followed by its IP address. The three fields were all filled up automatically, by the router. I never filled this up. However, I configured the router with the necessary details.
Troubleshooting:
1. Ping your device from your PC or notebook.
The idea is to be able to see if there is communication between your router and the device.
Example: at c:\>ping ......... (.....being the name or IP address of your device as entered in the router)
2. If you have a firewall, disable it now and ping again. This step is necessary because the firewall could be stopping your device from connecting to the router if it is not configured in the firewall's access list.
3. Go to your PC/notebook and type: ipconfig /all at the command prompt.
Hopefully, you should see the device's name come up as well as other parameters, including its MAC address.
4. Ensure that the device is allowed access to your internal network and configured as such, inside the router, using MAC address filtering. This means that you MUST ensure that the correct MAC address of the device has been entered.
Summary:
1. Configure your device inside the router - name/mac address or name/IP address
2. Configure your firewall to accept connections from the device
3. Ping the device as well as the router
4. If you have another computer, try and see if you can connect to the router from there.
5. Ensure that the router, PC or PPC are all on the same subnet. This is crucially important for communication amongst the devices.
By typing ipconfig /all, you will be able to determine as to whether all the computers as well as the PPC on your network are on the same subnet.
Many a network have failed through this problem.
Hope this helps.
kiwi992.

Categories

Resources