Database Users

solution to 1% flash failed problem (RSU_3.23.01.exe)

i have the same 1% flash failed problem. here's what i did.
1. prepare an SD card with the RUU_3.16.52 extracted using XDArit.exe (use XDArit.exe to transfer the ROM in c:\program files\RUU\english\NK.nbf to the SD) you need to have a USB SD Card Reader in order to do this. buy one if you have to.
2. prepare a second SD card with the repair files stored in the root directory (RSUpgrade.sa.CAB 4,305,434bytes, and the 2577 folder) just like whoever suggested, but replace the RSUpgrade.sa.CAB on the root of SD with the one you extracted in c:\program files\Radio Stack Upgrade Utility\RSUpgrade.sa.CAB (4,328,441bytes) by running RSU_3.23.01.exe (which had unfortunately caused the failure.)
2. insert the SD card with the RUU_3.16.52. press the power button while performing a soft reset. you should enter the wallaby loader screen. i have version 5.15. press action to flash the ROM to your xda.
3. cold boot your xda. you should see the blud Qtek screen. in the lower-right-hand corner you should see
G
R
3.16.52
4. you may be asked to calibrate your screen by tipping the four corners.
5. press the volume button. insert the second SD card (containg the repair files and the 4,328,441bytes SUpgrade.sa.CAB (NOT the 4,305,434bytes one, because it will cause freezing at 1%!) wait patiently until the upgrade finishes. you may put the xda back to the cradle for power as long as it doesn't reset itself.
if anything goes wrong, start from step 2 again.
NOTE: i may have skipped some steps in the above. but that's the best i could remember. good luck.
if you haven't upgraded the Qtek ROM and the Radio Stack, learn the risk before attempting!!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Hi baekdoosan !
It is nice, but don't work for me.
Any tips ?
Best regards
Sebi

Same Problem for my MDA. It crashed during update to t-mobile 3.23 MDA and i still get the message flash failed at 1 %.

Please !!!
Help Me !!!

hi
i have same problem...............i sent it to service center in my country
and the they are solved it
i think they make just downgrade

Hi Anybody !
This problem not solved !
RSU downgrade ? Possible ?
Any idea ?
Sorry my poor english.
Sebi

Where did you get the recovery files from???
I am digging around trying to fix a TMobile update from an ATT rom image and can't seem to figure out where you got the recovery files from...
Any help would be appreciated...
Todd

How to cardflash with hareld?

Hi
does anyone know how in need to call the "ARTEIMG.nbh" with the hareld when I am using this manual:?
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
Empty (erase the contents) of your microSD card from the Windows Mobile file explorer or format it from your computer using a card reader (in some cases format doesn't work).(not necessary, do it only if 1st attemt fails)
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
Rename the .NBH file to ARTEIMG.nbh and copy it to the root folder of your microSD card.
With microSD card inserted on the phone, start the bootloader (The bootloader is invoked by pressing down the Record button and using the stylus at the same time to press the RESET button at the left side).
You should see the screen pictured on the left, confirm flashing on screen by pressing the volume slider down.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
SuperCID devices are able to flash any NBH image using this method.
Click to expand...
Click to collapse

some few more question
witch of these files do I need to give the name???
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

does nobody has experience with this???
I really need to do this so I can send it to repair...

haha problem solved.
In someway my phone was able to connect with my pc with a broken usb. haha
In bootloader mode it just worked

Why do you want to update your rom this way?
It is much easilier with the HARD-SPL or USPL.
Look a bit around the herald forum and you will find these methods!!!

Yes I know but my usb connection in my phone broke down, so i need to send it to repair.
But i had the touchit rom on it, so with that rom I didnt had any garantee

HELP! Problematic WM6 rom load. Phone inoperative

Hi everybody. I'll try to brief 2 days of an unsucessful rescue operation. I have a XV6700 by Verizon, Tried to flash the WM6 Verizon rom first. My BL version was 2.05, so I had to downgrade to the 2.02. I followed step by step on some guy's post on PPCgeeks. the operation got messed up somewhere in the middle and my nightmare started right there. When flashing the NOID rom to the phone, it gave me an error and now it won't take back the OEM AKU 3.3, it says, WRONG DEVICE, this application is not made for your device. So I forgot about the OEM, tried to COOK a custom rom using kitchen, the only one that the phone will accept is the one with RUU - NO ID and Carrier Generic or Verizon, the ROM flashing process starts at STEP 3! it doesnt do radio upgrade , it starts right on "Upgrading CE..." and at 99% it fails. the phone then, boot ( weird boot screen, pixels, colors, lines ) followed by a blank ( white ) splash screen. and thats it. So i managed to find a GENERIC version of the WM6 already compiled. That one gives me the same error, error 112 ( see picture ) at 99% and boots with the same weird boot screen, blank splash, but this time it does show partial WM6, i can access programs, answer call, messaging etc. but it shows overlapping fonts, and the Dialer is tottaly blank. I tried installing more than 10 different dialers, but the phone screen is blank. Now I need help. I am afraid to make it worst. what could be wrong? My BL shows 2.02 .... but using the mytty software and punching task 28 55a ( as explained on the downgrade procedure ) it doesnt show what it's suppose to show. Heeeeelp!! Thanks
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

HTC hero bricked .help.....

I bought my HERO just a few days ago.
Once,the system halted and I took the battery out of the phone.
After that,when I turn on the phone,it show the first picture in the attachments
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and then only when I press the DIAL button ,the phone responses,and it shows the second picture in the attachments
I have checked that the buttons of the phone are all OK.
And I have sent it to someone to mend it,he said that the phone can not be connected to the computer,but he succeeded in flashing it with the miniSD memory card. BUT the phone still has the same problem.What's more ,the H-BOOT has been flashed by him from 1.76.005 to 1.76.007. But the problem still
exist....
Can anybody help me?...
And I'm from China,my English is not very good...

This might help...
g0mib0y said:
EDIT: DON'T UPDATE TO 2.1 AGAIN SINCE IT WILL HANG ONE MORE TIME. WAIT FOR HTC TO RESOLVE THIS ISSUE!!!!!!
EDIT 2: BACK UPP ALL YOUR DATA FROM YOUR MEMORY CARD FIRST!!!
EDIT 3: How did I find this out? I talked to a very helpful HTC suport rep (yes they do actually exist in Sweden). He helped me do these steps and so I thought I should share this.
Ok so you got a message that 2.1 was available for your Hero - FINELY! and you installed it using OTA. And then you got a triangle with a ! in it and you rebooted and all it says is "HERO".
This is how to solve it!
Take out your memory card. FORMAT TO <span style="font-weight:bold;">FAT32</span>!!!
Download the RUU 2.73.405.5 from HTC support homepage
Run the installation.
When it fails to find your phone <span style="font-weight:bold;">DON'T EXIT!!!</span>
If you are using Windows 7 go in to c:\Users\<span style="font-style:italic;">yourusername</span>\AppData\Local\Temp
Search for ROM.zip
Move to desktop
Rename to HEROIMG.zip
Transfer to your newly formated memory card now with FAT32 file system
Put memory card into phone
Start phone holding volume down pressed.
It will now check zip fil and then ask if you want to install.
homekey for YES
After installing you have 1.5 again and can safely upgrade to 2.1 OTA
Click to expand...
Click to collapse

HTC surround enter usb host mode after unlock by XTC clip

HTC surround T8788 AT&T enter usb host mode after unlock by XTC clip.please help me.Thanks.

Just reflash your phone.

eglunas said:
Just reflash your phone.
Click to expand...
Click to collapse
i flash RUU_Surround_TELUS_WWE_1.04.661.00_Radio_5.51.09.29_22.32.50.10U_by_ansar
but error 294 : invalid vender ID.i need rom at&T please help.

Here is the At&t ROM its the original 7.7004
http://www.megaupload.com/?d=KY9UZEHI
(Charge Battery to 100%)
With the phone powered off hold volume down and power button to boot into Bootloader screen (Red Blu Green White),plug in usb cable to computer and into the phone(it will say "serial" at the bottom ( let it install the qualcomm cdma driver) Then "serial" will change to "USB" at the bottom of the phone screen, extract the ROM.zip file from download link above and click the Rom update utility EXE and follow the instructions from there.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Ok I need you help please, I have the same problem with my htc 7 surround of AT&T, but I didn´t use the tool "unlock by XTC clip". My phone worked well, but the last week, it freezing in the logo "HTC" and don´t pass from here; it do not start wp7.
I use this tool that you give from megaupload but when the program verify the image version of my htc - it is in blank, my phone phone don´t have image version- I don´t know what I have to do. I use everything to install a new windows phone 7 operating system to my htc surround.
please give me a response...

i need this file but link not working again. says file might have been deleted
waiting for your response.

I need this file but link not working again. Thanks in Advance... Kamijee

deleted