Hi all,
I have an old school CarPC that I'm looking to refresh with Android Auto. The system in my car has a head unit and a somewhat unintegrated GPS system (separate screen from the headunit, which has no screen at all, only dumb controls). The way it works presently is my CarPC video is tied into the GPS screen and the audio is tied into the headunit Aux input.
You can see some of the details here if itnerested:
CarPC with stock Nav - RX8Club.com
Series I Interior, Audio, and Electronics - CarPC with stock Nav - hey gang.. just picked up an 05 ti grey rx-8 a few weeks ago, came with the full GT package, MS front and rear spoiler. still have the rear and side skirts to go. in the meantime, i decided to get going on the interior, adding a...
www.rx8club.com
What I'm looking for really is any hardware device that:
1) can run Android Auto
2) outputs video to VGA
2) accepts a USB controller for capacitive touch screen
3) accepts a USB controller for Car2PC/Aux input -- devices like these allow a standard audio jack plug into the Aux port, and then ALSO enables steering controls to work (volume, next/previous track, voice control prompt)
4) accepts a standard jack microphone
5) not critical but ideally accepts a radio antenna to integrate OTA radio signal into Android Auto
I *think* raspberry PI is my best option at this point, but it seems like it doesn't have all of the kinks worked out as of yet. If there is something I could install on the bare metal of my car PC, I think that'd be most ideal.
I'll appreciate any expertise on this!
Related
Does anyone know about the brand Naviskauto?XDA seems has no much about this.I'm planning to have one android head units for my VW.And accidentally got a promo code of this store from Dontpayfull.
I need GPS of course,bluetooth,iphone,ipad. .Any advice,guys?
Naivskauto Unit C250
summerof said:
Does anyone know about the brand Naviskauto?XDA seems has no much about this.I'm planning to have one android head units for my VW.And accidentally got a promo code of this store from Dontpayfull.
I need GPS of course,bluetooth,iphone,ipad. .Any advice,guys?
Click to expand...
Click to collapse
This unit is the same as pumpkin RQ0255 unit. There is more information available from their support page and is directly applicable to the Naviskauto unit you have.
I installed this unit with a Metra dash kit into a 2003 G35 Sedan with Steering wheel controls (kit required) / the stock Bose amplifier (audio interface kit required) / and reverse Cam. All the functions you want are available. I assume you want to connect iphone/ipad via bluetooth , it works but the bluetooth interface for music isn't great , and maybe a 3rd party app is available. There is an "IPOD" USB connection through a 30pin connector. (Overall, music quality is very good but not as good has name brand head units for USB/Bluetooth/Radio. ) I use an Iphone 4 as an Ipod over USB, but you should be able to use a lightning convertor cable and use newer iphones/ipods. The music interface is better on USB but still falls short if you're looking for iphone/ipad useability. You can connect the head unit to a wireless hotspot on iphone/ipad or any device with this function. You can also connect via USB to a 3G dongle but the supported devices are limited, (more reading for you.)
GPS works great and the iGo Navi app provided is really good and does not require an online connection. You may need to do some more reading to get maps / poi functioning to your needs depending on your location.
It's my first android head unit install and it was flawless for me. I invested lots of time reading to extract experience from this board and others I am generally familiar with car sound systems, electronics, soldering so I was just a matter of understanding the wiring interfaces for this unit, which are standard.
I'm a newbie on Android , so I'm not experimenting with ROMs yet but there is a ton of info on what is possible with mods and replacement apps for various functions.
so, bottom line, I give the unit a 8/10 overall, but the value for money from Amazon I give it 9/10.
Chieftan123 said:
This unit is the same as pumpkin RQ0255 unit. There is more information available from their support page and is directly applicable to the Naviskauto unit you have.
I installed this unit with a Metra dash kit into a 2003 G35 Sedan with Steering wheel controls (kit required) / the stock Bose amplifier (audio interface kit required) / and reverse Cam. All the functions you want are available. I assume you want to connect iphone/ipad via bluetooth , it works but the bluetooth interface for music isn't great , and maybe a 3rd party app is available. There is an "IPOD" USB connection through a 30pin connector. (Overall, music quality is very good but not as good has name brand head units for USB/Bluetooth/Radio. ) I use an Iphone 4 as an Ipod over USB, but you should be able to use a lightning convertor cable and use newer iphones/ipods. The music interface is better on USB but still falls short if you're looking for iphone/ipad useability. You can connect the head unit to a wireless hotspot on iphone/ipad or any device with this function. You can also connect via USB to a 3G dongle but the supported devices are limited, (more reading for you.)
GPS works great and the iGo Navi app provided is really good and does not require an online connection. You may need to do some more reading to get maps / poi functioning to your needs depending on your location.
It's my first android head unit install and it was flawless for me. I invested lots of time reading to extract experience from this board and others I am generally familiar with car sound systems, electronics, soldering so I was just a matter of understanding the wiring interfaces for this unit, which are standard.
I'm a newbie on Android , so I'm not experimenting with ROMs yet but there is a ton of info on what is possible with mods and replacement apps for various functions.
so, bottom line, I give the unit a 8/10 overall, but the value for money from Amazon I give it 9/10.
Click to expand...
Click to collapse
Thank you for your information.You're more experienced than me as I can tell. According to the review,it seems a good choice.I will look at more and make a "experienced" choice,I think.thanks again,man.:good:
Here's an initial review for the Ownice K1 (2gb ram/ 16gb Rom android 8 version) and from what I can tell, the first one to appear in English.
Background: This is Ownice's new budget model. No built in 4G support, no DVD slot, 4 core processor, slightly lower internal components (Amplifier, Tuner), TFT screen.
I ordered it on the 11.11 sale for about $200 with DHL shipping and added another 9$ for an external Mic. I ordered the version customized for Ford Mondeo/Galaxy/ S-Max.
Also ordered from other vendors: Ownice TPMS system (has not arrived) , Huawei E8372 4G wingle (arrived shortly after the K1 was installed), and reverse camera that replaces license plate light
Ownice shipped it three days later and it arrived in LA four days after that. From there it was brought to Israel by my kind brother.
Initial Impressions: came well packaged with protective film on the screen. Construction seems good. This is a slim unit and nearly all the connectors are breakouts from proprietary pin-outs on the back.
Installation:
Installation into a 2013-14 S-Max was quite easy as it simply uses the same mounting holes as the OEM unit, and the included connector is wired for the Ford quadlock harness. That said, it included no documentation whatsoever.
1) Connect three rear break-out connections to the back (Quadlock harness, A/V in/out cables, External mic input) and plug the included canbus decoder into the harness
1a) Notice that on harness wiring there is a wire that has a locking connector in the middle that comes disconnected. Assume this is for the reverse camera and connect it
2) Connect quadlock, revers camera RCA. External Mic, GPS antenna, and radio antenna
2a) Notice that they did not include a correct antenna adapter, run to local car audio guy and overpay for an adapter
3) (Spend next six hours wiring in a reverse camera through hatchback (not so easy!)
4) Shove all the wiring behind the unit (plenty of room there) and screw it in, replace trim, voila.
Future items:
5*) 4G wingle arrived a day later so I have only used it with the K1 in hotspot mode, which works fine. I have not gotten around to attaching it directly via USB
6*)TPMS system ordered from DX.com has not arrived yet.
In Use: In the realm of chinese android head units it is no faint praise to say that a unit simply works as one would expect it to, and this unit really does just work 99% as it should. I'll only point out some highlights and a few small disappointments:
+Unit powers on as soon as key is in ignition, stays on after car is shut down until door is opened (just like OEM)
+The reverse camera comes on BEFORE the unit is fully booted (right after the splash screen) so no significant delay there (this was a very pleasant surprise)
+No need to attach extra reverse wiring from reverse camera to car wiring, reverse is already wired via quad-lock
+Steering wheel controls work as they did with OEM unit (but mode button cycles through all inputs, even if they are not installed)
+My existing BAFX bluetooth OBD2 connected fine and works with the included version of torque
+Sound quality with OEM speakers is fine, at least on par with OEM head unit (despite what I've read about ST TDA7388)
+External mic is sensitive enough to work installed in hidden OEM mic location (grill behind map light)
+GPS reception/accuracy is better than my phone's
+Screen splitting works, and is useful
+Push the right knob in and the screen goes blank
-Radio tuner is not as good as the oem unit (I expected this)
-Bluetooth popup to answer calls does not appear for whatsapp calls
-Touchscreen could be a tad more sensitive
-built in media player does not seem to support WMA (thanks to yahoo music (RIP) I have a lot of WMAs) so I mostly use VLC
-No printed manual, onboard manual app does not work, and I can't find any manual online, so it took some futzing and going through the C500 manual to figure a few things out.
That's about it. I don't spend that much time driving these days so haven't gotten around to exploring all the settings and features, but so far I'm quite satisfied.
I appreciate the review; some follow-up questions...
Please tell me if steering wheel controls (up/down track) work on all music apps or just the stock one. Also let me know if you hear any background clicks/pops/noise when WiFi is being accessed. How is the Bluetooth calling quality - can callers hear you ok? Finally can the stock radio and Bluetooth apps be used split screen?
Thanks!
Jeff
twokidsandaphone said:
I appreciate the review; some follow-up questions...
Please tell me if steering wheel controls (up/down track) work on all music apps or just the stock one. Also let me know if you hear any background clicks/pops/noise when WiFi is being accessed. How is the Bluetooth calling quality - can callers hear you ok? Finally can the stock radio and Bluetooth apps be used split screen?
Thanks!
Jeff
Click to expand...
Click to collapse
1) Steering wheel controls work with all aps.
2) Haven't heard any noises caused by wifi
3) Bluetooth call quality is good, definitely go with the external mic
4) Yes, those apps and most others work in split screen.
Doncres said:
1) Steering wheel controls work with all aps.
2) Haven't heard any noises caused by wifi
3) Bluetooth call quality is good, definitely go with the external mic
4) Yes, those apps and most others work in split screen.
Click to expand...
Click to collapse
Thanks for the answers. One more question, sorry. Does Ok Google work, and/or can you use Google to initiate a call just using voice or microphone button plus voice? Many units "understand" the request to call but fail to be able to put through the call.
Thanks again!
Jeff
Follow -up notes
twokidsandaphone said:
Thanks for the answers. One more question, sorry. Does Ok Google work, and/or can you use Google to initiate a call just using voice or microphone button plus voice? Many units "understand" the request to call but fail to be able to put through the call.
Thanks again!
Jeff
Click to expand...
Click to collapse
Sorry for the delay in replying.
As far as OK google calls, since the head unit's Bluetooth functionality works as a microphone/speaker, when you run a google now command on the HU, it thinks you want to make a call using the HU, but it has no phone function of it's own, so it cannot place the call. What would be needed is a button on the HU that activates the phone's google now listening. I don't keep my phone in constant listening mode, so not sure how it would work in that situation. Hope that helps.
Here's a few more observations, not entirely good:
1) The steering wheel next and previous track buttons are reversed.
2) There is a problem resuming Bluetooth streaming from my phone. If you push the play button on the HU Bluetooth app after a restart it will freeze and force a reboot.
3) GPS reception is generally excellent with very quick fix, but occasionally for no apparent reason upon startup it will take 5 or so minutes.
4) Even disabling all of automatic time setting, the unit will inexplicably get an hour ahead when booted and then correct a few minutes later.
5) I can't figure out if there is a way to get the Huawei 4G USB router I bought to function as a modem or only as a hotspot.
Hi Doncres,
I've just finished installing my own Ownice K1/G10 unit for my Hyundai Santa Fe.
Installation was a little bit trickier since in order to use the car's original gps antenna, microphone and rear camera I had to cut some wires and change connectors, as well as installing a stepdown DC-DC converter to get the weird 6.5v power required by the original rear camera.
I've been playing a little bit myself with the unit and, given that I'm quite satisfied with it, I would like to know whether you experienced any of the following little annoying problems:
- handsfree call via bluetooth: remote party is always complaining about a small amount of echo
- general audio volume low even at maximum volume (+30), especially for bluetooth phone calls
- the bluetooth active call popup rectangle gets always in the way, even when the rear camera is triggered by the reverse gear, giving some troubles when parking the car and talking to the phone
- Netflix app not working: I had to install an old 2015 version targeting Android 4.4
- parking assistant lines on the rear camera view have wrong perspective angle in comparison to my camera's viewing angle, thus resulting in a projected trapezium rather than a projected rectangle (i.e. the lines are not parallel to actual parking lines); I know I can disable them, however I'd like to change their perspective angle to match the camera
I read somewhere that there are two hidden service menus on Ownice units: the first is accessible via car settings (the "1260" menu) and this works on my unit
The other should be accessible by dialling a specific string in the phone app, however it seems I cannot start the phone app since the K1/G10 comes with no 3G/4G hardware. Any idea on how to enter such menu?
Thanks,
Alberto
agpastore said:
Hi Doncres,
I've just finished installing my own Ownice K1/G10 unit for my Hyundai Santa Fe.
Installation was a little bit trickier since in order to use the car's original gps antenna, microphone and rear camera I had to cut some wires and change connectors, as well as installing a stepdown DC-DC converter to get the weird 6.5v power required by the original rear camera.
I've been playing a little bit myself with the unit and, given that I'm quite satisfied with it, I would like to know whether you experienced any of the following little annoying problems:
- handsfree call via bluetooth: remote party is always complaining about a small amount of echo
- general audio volume low even at maximum volume (+30), especially for bluetooth phone calls
- the bluetooth active call popup rectangle gets always in the way, even when the rear camera is triggered by the reverse gear, giving some troubles when parking the car and talking to the phone
- Netflix app not working: I had to install an old 2015 version targeting Android 4.4
- parking assistant lines on the rear camera view have wrong perspective angle in comparison to my camera's viewing angle, thus resulting in a projected trapezium rather than a projected rectangle (i.e. the lines are not parallel to actual parking lines); I know I can disable them, however I'd like to change their perspective angle to match the camera
I read somewhere that there are two hidden service menus on Ownice units: the first is accessible via car settings (the "1260" menu) and this works on my unit
The other should be accessible by dialling a specific string in the phone app, however it seems I cannot start the phone app since the K1/G10 comes with no 3G/4G hardware. Any idea on how to enter such menu?
Thanks,
Alberto
Click to expand...
Click to collapse
Hi, I'm not sure I can really help other than to confirm a few of the the issues.
-Don't think I have an echo issue, but there seems to be a delay until a caller first hears me.
- I get very good volume. I would assume this is an issue of whether the built in amp is a good match for the speakers. Could be an issue with the impedance.
-Yeah, the call button overlay is sometimes annoying, it can block nav screen as well and no way to hide
-I noticed that Netflix was no showing in the app store, but not a big use for me
-the camera I bought has built in guidelines so I disabled them.
-no idea bout the service menu
The only issues that really bother me are:
-the occasional GPS not acquiring satellites, which I now think may be from a defective antenna. I ordered a replacement and we'll see if that helps.
-the fact that if I have an app like stitcher playing, i then get in the car and it stops it when it connects to the BT, but when I go to the BT music app it will either resume fine or if I pres play it will crash the entire device and force a reboot. Mostly I just run streaming apps on the Unit so not much BT streaming anyway.
Also, my TPMS unit finally showed up 2 months after ordering it from DX.com. Looking forward to installing that some time in the next couple of weeks.
Hi.
I am newbie, and i may be wrong in posting the question.
I got 2 din touch Android for Nissan Murano 2018 - model K1, 2 / 16 GB. Ownice 8227L.
On the manufacturer's website, the model has not been supported by software updates for a long time.
Last owner tried to update it with different firmware versions, including those downloaded from this site, and from 4pda. initially did not save the software that was on it from the factory. Now - it has a version of Android installed in which the radio does not work. Everything works, sound files from usb card play, except the radio.
Help me please, where can I get the firmware on it to make the radio work?
Hello,
I installed the FunRover Android 8.1 Intel Airmont eight-core 1.8GHz SC9853i (4GB RAM, 64GB flash) on my Skoda Octavia 2 FL RS (2010).
I would like to provide an intial feedback to all who might consider this headunit and ask some questions regarding setup of some Android headunit features.
Links to setup:
Headunit: https://www.aliexpress.com/store/pr...ml?spm=2114.12010612.8148356.2.20b456d00mOBJe
DVR Camera: https://www.aliexpress.com/item/HD-...ml?spm=2114.12010108.1000023.7.35b11b8d1Fd2HV
1) Installation:
Pro:
- plug and play - no extra adapters needed
- direct integration with can for vehicle information like: door open, car sensors, steering wheel controls, AC info
- good fit
Cons:
- held in place only by the frame's plastic pins
- it provides a single USB, the second one has an AUX cable plug that is fit if you have the original oem usb cable, so make sure you have it or buy the proper aux to USB cable if you need two USB ports
2) Look and Feel:
Pro:
- good design
- pleasant touch feel
- somewhat responsive
Cons:
- the screen seems to be of less than high end quality: left side touchscreen buttons section seems slightly detached from the frame (1-2 mm) and moves when pressed
- the screen is not IPS... the seller added a note on the site that you need to ask specifically for IPS screen....
- glass protector and screen reflect strongly in daylight so it is not ideal
- the silver frame has a gold tint so it does not match the silver dashboard tint from the car perfectly
- touch buttons do not respond always - you find yourself having to push twice for a response
3) Hardware & related features:
Pro:
- specs seem enough for anything you may need
- built-in 4G modem
- good GPS signal
Cons:
- intel / platfrom heats like crazy - average CPU temp is 80C - screen gets hot because of this
- only one 4G antenna - but stil OK signal
- extremely poor WiFi signal (phone has full wifi from router and the headunit has maybe half or even losing signal)
- 4G modem has poor speed, maybe you get 300KB download speed over 4G
- hardware has poor screening for interference: radio has a "buzz"; even with all audio stopped you get a hum in the speakers
- sound is poor compared to a high / mid radio: I had the Skoda Bolero unit and the sound is twice as good; after some EQ tweaks I was able to get a decent sound quality, but you will need an external amp if you want mid/high sound quality
- screen is reflective; maybe if you ask for the IPS version it will be better
- bluetooth seems to disconnect when on a bumpy road... so I'm putting this on HW; must test more
4) Software:
Pro:
- stable up to now
- quick cold boot (compared to an Ownice500 I had)
- sleep option makes almost instant boot, but I am worried of battery drain so I turned it off as you can't configure a max sleep time before complete shutdown (as you can on other headunits)
- reverse supports steering direction via can (the lines move when turning the steering wheel); also standard OEM parking sensors are supported
- support for vehicle info
- you can update the DVR app to gain some virtual adas features
Cons:
- the worst UI I saw, heavily restricted regarding customization - however I noticed the same is on Joying Intel units
- limited OS options compared to other Android Headunits, but sufficient for non Android geeks
- Radio app does not scale when used in split screen
- widgets from newly installed apps only show up after restart
- no manuals or detailed OS / SW options explained. You have an operational instructions app, but the descriptions are basic.
- reverse cam is not instant - has a 5s delay for app up
- the screen brightness can be controlled from the headlights setting or "time" - but the time can't be configured and is not synchronized with the sunset information from google maps for example
- minimum screen brightness can be too high for some people
- volume control is not separate for notifications etc. it's just one volume slider; you can configure some sound ratios between media, navigation , bluetooth, but that's it.... compared to ownice where you could configure nav / bluetooth / etc volume on the fly
- does not integrate with the car bluetooth module for audio output... but I guess it's too much to ask
- major issue with sound volume: seems related to using the steering wheel volume up/down - results in volume going to max or min randomly and using any button (screen, physical or steering wheel) only slows it down, but it's like it keeps getting the command to do volume up or down in paralel to any additional input you may do. You gain control after 10-30s if you keep pushing the mute / volume up/down on the steering wheel, however it is DANGEROUS (especially when it goes to MAX volume) because it can blow your speakers or scare the hell out of you / maybe cause an accident when it happens during driving.
5) External accessories:
5.1) FunRover DVR cam:
Pro:
- good viewing angle (170)
- plug and play
- DVR app works out of the box; starts automatically on boot and records 2 min time loop while overwriting oldest files
Cons:
- extremely limited DVR app - basically NO options to configure
- no file management; can't access the MicroSD card files of the camera from the headunit file manager; only works in the DVR app but I can't find a way to move / share these over to a separate location - e.g. google drive
5.2) External MIC:
- non existent - even though the seller said they will send it as gift it was not in the package
5.3) Reverse camera:
- I did not install it yet; I will get another HD cam and make a comparison with the packaged one
Questions:
A) What UI/Launcher do you recommend for such platforms? Will it show the built in apps (e.g. radio) or will they have to be reinstalled?
B) How can I manage or move files from DVR to another location - e.g. on headunit storage? DVR has... Novatek chipset. Do you recommend another DVR app?
C) What widgets / apps do you recommend to use for displaying the CANBUS information? I will try realDash to see if it can take the canbus source...., however I was hoping to have something like a widget on the homescreen and not an app
D) Did anyone encounter the sound volume uncontrollable volume issue? I already disabled the "bluetooth absolute volume" with no change in behavior. Also none of the sound settings made a difference. It seems like somehow the signal from the steering wheel button is processed in a loop. From my current experience it seems to be a canbus decoder or HU software issue.
E) Did anyone manage to integrate such a headunit with the skoda bluetooth module for audio output?
You can ask me other questions about this headunit and I will answer / test.
Have fun!
Hi, I just bought the same radio, but for Mitsubishi ASX. My first impression is almost the same like yours. My main problem is external microphone - when I use bluetooth for call, only internal mic is working.. :/ (matter of adjustment??). also RDS on radio is almost invisible..
I am looking for this device, now its android 9.0, but not sure if still TFT and not IPS screen. @axicos do you know if they improved this unit?
My new funrover arrived. Looks beautiful, ips screen, android 9.0, 2 USB (with CarPlay) but I have some issue's:
- parking sensors activate screen info when switched on by button or reverse, but don't shows the distance
- a/c temp is 2°C below the select one on the controller
- car settings menu : I can't activate any option
My car it's sa 2013 Passat variant.
Hello everyone,
I am planing on inserting an Android 9.0 head unit with PX6 into my Merc CLK (209 series from 2004), but unfortunately Mercedes made damn sure to make life as unpleasant as possible if you want to tinker with their fibre optic D2B Bose System. So in order to get any sound with the built-in Bose speaker system you have to stick to their dated radio equipement with fibre optic capabilty. I don't wanna rip out the whole Bose System at this point and converter boxes only exist for M.O.S.T devices which followed after D2B. Fortunately you can modify their smallest D2B radio with an aftermarket Bluetooth chip and give it some modern day connectivity. And this is where my question comes into play:
Is it possible for those Android head units to send audio "outwards" via bluetooth ? The main idea is for the Unit to stream it's audio signal (like an ordinary phone or tablet) to the Merc Radio, which will be hidden in the glovebox, consequently acting as an "external bluetooth speaker".
And if it's not possible for the head unit to do so, can they be modified / adapted with a dongle, etc. of some sorts to transmit bluetooth? Creative constructive suggestions are very welcomed here. The ideal constellation would be in the end: Phone/OBD2-dongle/etc. connected to radio connected to Merc Radio Bluetooth receiver. So multiple bluetooth connections should co-exist at the same time.
I know I am probably asking for a lot here and I am of course willing to take cuts, so the most important feature would be for the Head unit to emit all its audio signals to the "Merc Radio bluetooth speaker".
So any pieces of advice from the experts here would be very much appreciated! :fingers-crossed:
Best regards,
Alan
Is the fibre optic system SPDIF / TOSLINK? There are head units that have SPDIF out (Joying, via Coax - but you can convert Coax to TOSLINK easily).
You can also get USB SPDIF but they seem hit or miss. Depends a lot on the version of Android you use, and some will not allow OS to control volume, etc.
To answer your original question - seems like my head unit only acts as a bluetooth server, not client. It cannot connect out as you are asking.
I am in a near-identical situation as you (2003 Sl55 with d2b Bose system). My current plan is to run the audio coming out of the android head unit into an RCA to AUX adaptor, which then plugs into the aux input on my command system. The command will be relocated to the boot and connected to the Bose amplifier over D2B.
rewen said:
Is the fibre optic system SPDIF / TOSLINK? There are head units that have SPDIF out (Joying, via Coax - but you can convert Coax to TOSLINK easily).
You can also get USB SPDIF but they seem hit or miss. Depends a lot on the version of Android you use, and some will not allow OS to control volume, etc.
To answer your original question - seems like my head unit only acts as a bluetooth server, not client. It cannot connect out as you are asking.
Click to expand...
Click to collapse
Hi Rewen,
unfortunately no. It's a proprietary Mercedes System which was not Used anywhere else in that form (at least to my knowledge). It was changend to M.O.S.T in 2004/2005. So Support from third party developers is basically non existent. If you do research on that topic you usually come to the conclusion "stick with it or exchange the speakers, amps, radio....alltogether. It's not the best sounding system to be honest, but for now i don't want to put up with the hassle and the cost of a complete good quality car hifi system.
Thanks for you info, i guess this will account to probably all head units, so i will just stick to a transmitter dongle in the back of the head unit then. That should do the job.
joe2212 said:
I am in a near-identical situation as you (2003 Sl55 with d2b Bose system). My current plan is to run the audio coming out of the android head unit into an RCA to AUX adaptor, which then plugs into the aux input on my command system. The command will be relocated to the boot and connected to the Bose amplifier over D2B.
Click to expand...
Click to collapse
Hi joe,
SL55? very nice choice!
After all my research so far i think the Aux cable / Bluetooth dongle method is the most "acceptable" solution for any D2B owner who wants to stick with the Bose system but also wants an android head unit. I was also thinking of just using an Aux cable (Have the Comand 2.0 with AUX), but i ran into a lot of interference noice with the cable, therefore i was driven away from that idea. That's why I will just get a used Audio 10 CD with D2B, modify it with bluetooth and replace my disc changer with it. This will hopefully spare me from running any cable through the car....(too lazy for that right now^^)
Modify Android 8.1 head unit for better menus & easier BlueT controller compatibility
I bought an iMars 7 from banggood, I believe it’s called a “Android Head Unit AC8227l” but from reading on here it could be a YT9217 or a YT9218 (?)
The menu systems I’ve seen running on these online, on pics or YouTube videos vary. But my menu system is quite clunky and limited.
I can connect a phone via Bluetooth for calls or on-device music controls, but I can not connect any Bluetooth controllers (I’d like a Bluetooth control for music and calls since using a touch screen and driving is a no-no). But I would also like to connect a Bluetooth games controller for my girlfriend to be able to play on it when we’re driving on long journeys.
Also, some better menu controls would be useful as the settings are limited at brightness, WiFi, and a few other minor things. Some display settings, better sound settings, and some others would be really useful.
I havnt wired the radio antenna in because of a lack of a female to female jack, and the reverse camera hasn’t been set up yet so their compatibility isn’t an issue right now!
Is there a way of modifying the software to allow for what I’m after? I’m decent with tech, but rooting an android device (even if that’s the correct terminology) is new to me!
Thank you for any help or advice
Braadlee said:
I bought an iMars 7 from banggood, I believe it’s called a “Android Head Unit AC8227l” but from reading on here it could be a YT9217 or a YT9218 (?)
The menu systems I’ve seen running on these online, on pics or YouTube videos vary. But my menu system is quite clunky and limited.
I can connect a phone via Bluetooth for calls or on-device music controls, but I can not connect any Bluetooth controllers (I’d like a Bluetooth control for music and calls since using a touch screen and driving is a no-no). But I would also like to connect a Bluetooth games controller for my girlfriend to be able to play on it when we’re driving on long journeys.
Also, some better menu controls would be useful as the settings are limited at brightness, WiFi, and a few other minor things. Some display settings, better sound settings, and some others would be really useful.
I havnt wired the radio antenna in because of a lack of a female to female jack, and the reverse camera hasn’t been set up yet so their compatibility isn’t an issue right now!
Is there a way of modifying the software to allow for what I’m after? I’m decent with tech, but rooting an android device (even if that’s the correct terminology) is new to me!
Thank you for any help or advice
Click to expand...
Click to collapse
Sorry to say, but forget about all your wishes. BT is not available for other devices as phone and OBD.
Modifying the software to get this fixed... good luck...