Hi, I'm using odin 3.09 and odin 3.10
I downloaded twrp from the oficial page for sm-n900 (ha3g) .
I follow these steps:
https://forum.xda-developers.com/showthread.php?t=2704363
- Phone enabled usb debugging.
- phone with 80% or more
- odin show PASS in green when the process finished.
but when i try turn on with vol up + home + power enter to STOCK recovery...
ADVICE: This phone was rooted, and then unrooted (from menu of supersu app) ...
MY FAULT ...
It needs root before install custom recovery !
Fixed ... Working
Hey everyone, I just wanted to make this thread about rooting the J7 on Boost after upgrading to Nougat. I did not want to try the old root method because of the new firmware for the simple reason of I was afraid to be bricked. Therefore i tried this and it worked
*Disclaimer* I am not responsible for any damages to your device. Do at your own risk. I am also not a developer in any kind of way and will most likely not be able to answer any questions to problems you face. This method simply worked for me after losing my root when i upgraded to 7.1.1 Nougat.
Requirements:
1) Odin (I used 3.10) https://odindownload.com/SamsungOdin/#.Wlpm26hKvIU
2) TWRP https://forum.xda-developers.com/galaxy-j7/development/recovery-twrp-3-0-3-0-galaxy-j7-t3560327
3) Supersu Zip http://www.supersu.com/download
4) An Unlocked Bootloader
Instructions:
1) Unlock your bootloader to enable developer options and turn on usb debugging tapping on about device 7 times and make sure OEM unlock is switched on when rooted (Never turn this off and reboot your device. You'll be soft bricked)
2) Put the Supersu zip file in your phone's storage
3) Boot your phone into download mode
4) Open up Odin and connect your phone
5) Uncheck Auto Reboot!!! if not, your phone will boot up automatically and you will lose TWRP after flashing
6) Flash TWRP where it says "AP"
7) After TWRP finish installing, pull the battery and put it back in and boot into recovery (Power + Home Button + Volume UP)
8) After booting into TWRP, press install and find the Supersu zip file
9) Flash it and then reboot (phone may boot loop a couple of times)
10) Download root checker from the play store to verify you have root
11) Enjoy
Thanks go out to minz1 for TWRP and the people of supersu
I have the J7 Perx (Boost) Software Version- J727PVPU3ARC2 (Nougat 7.0).
I have the j7 perx software v- J727PVPU3ARC2, I need to upgrade to Android Nougat 7.1.1 or higher again. Can you help with this? Please let me know.
Hello
I own a samsung galaxy C9 Pro SM-C9000 Android 7.1.1 Nougat
I only want to root the official ROM
I had to try everything possible
It does not work, impossible to install TWRP to boot for the rooted
the installation with Oden his pass very well but it does not boot on TWRP and the boot and completely corrupted
the phone is on it turns on but it does not go on the bootloader
the download mode works perfectly
Tested by my phone with the official ROM SM-C9000_C9000ZHU1BQL3 Android 7.1.1 Nougat
And i'm have same proplem.. I still cannot root it or flash twrp.. Can any one help us
please, it nobody has rooted the C9000 HK ?
I managed to install TWRP on my C9000 HK but it is that of the C900F version
TWRP-3.1.1-0-C900F
how to root please ?
I have successfully rooted the SM-C9000 with SuperSU and TWRP
it fake install TWRP-3.1.1-0-C900F
and formatted the DATA otherwise it will not work
after installing the SuperSU via TWRP
are you serious? Has your root and twrp worked? Tell me how and if possible give me the link
How To Root Galaxy C9 Pro SM-C9000 On Nougat 7.1.1 ? hong kong version
Special Notes:
1. DON'T FORGET TO ENABLE "OEM UNLOCK" (located in Developers options).
2. KNOX will be tripped once you flashed custom binaries to your phone.
(Your warranty may be voided. However this may not affect you if your country forces Samsung to provide hardware warranty regardless of software status.)
3. Samsung Firmware OTA (aka System Updates) will no longer work once you flashed custom binaries.
(You can flash custom ROMs if you want to keep the OS up-to-date.)
WHAT IS TWRP?
Team Win Recovery Project is a custom recovery for Android devices.
It allows you to back up and restore your data, flash custom ROMs to your device, repair broken file systems, and root your device.
How to intall TWRP using ODIN
1) Go to Settings » About phone » and tap “Build number” seven times to enable “Developer options”.
2) Go back to the main Settings page, scroll to bottom and select“Developer options” from there.
3) Under Developer options, look for “Enable OEM unlock”checkbox/toggle and make sure you Check it or turn it ON.
4) Now Boot your Samsung Android device into Download mode.To Do So Follow the steps below
5) Switch off your device.
6) Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
Once your device is in download mode, connect it to the PC with a USB cable. The Odin will automatically detect the device and show an “Added!!” message. If not then your device is not connected properly
7) Now click on the AP tab on Odin window and select the TWRP recovery .tar file that you downloaded for your device.
8) Click the Start button on Odin to start Flashing and wait for it to finish the process.
Once it finished successfully, a pass message on the Odin screen will pop up
Your device will automatically reboot when Odin is done flashing. Now You can disconnect your device.
Done!!! TWRP is now installed on your device
ROOT OPTIONS:
File needed
dzkouba said:
Special Notes:
1. DON'T FORGET TO ENABLE "OEM UNLOCK" (located in Developers options).
2. KNOX will be tripped once you flashed custom binaries to your phone.
(Your warranty may be voided. However this may not affect you if your country forces Samsung to provide hardware warranty regardless of software status.)
3. Samsung Firmware OTA (aka System Updates) will no longer work once you flashed custom binaries.
(You can flash custom ROMs if you want to keep the OS up-to-date.)
WHAT IS TWRP?
Team Win Recovery Project is a custom recovery for Android devices.
It allows you to back up and restore your data, flash custom ROMs to your device, repair broken file systems, and root your device.
How to intall TWRP using ODIN
1) Go to Settings » About phone » and tap “Build number” seven times to enable “Developer options”.
2) Go back to the main Settings page, scroll to bottom and select“Developer options” from there.
3) Under Developer options, look for “Enable OEM unlock”checkbox/toggle and make sure you Check it or turn it ON.
4) Now Boot your Samsung Android device into Download mode.To Do So Follow the steps below
5) Switch off your device.
6) Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
Once your device is in download mode, connect it to the PC with a USB cable. The Odin will automatically detect the device and show an “Added!!” message. If not then your device is not connected properly
7) Now click on the AP tab on Odin window and select the TWRP recovery .tar file that you downloaded for your device.
8) Click the Start button on Odin to start Flashing and wait for it to finish the process.
Once it finished successfully, a pass message on the Odin screen will pop up
Your device will automatically reboot when Odin is done flashing. Now You can disconnect your device.
Done!!! TWRP is now installed on your device
ROOT OPTIONS:
File needed
Click to expand...
Click to collapse
Hello :3 i performed the same steps but it just keeps corrupting my stock/current rom after i flash twrp. Some people face this same problem... What they can do is they can flash back the original samsung rom without the stock recovery, so then the twrp one will be there.
Bilal54 said:
Hello :3 i performed the same steps but it just keeps corrupting my stock/current rom after i flash twrp. Some people face this same problem... What they can do is they can flash back the original samsung rom without the stock recovery, so then the twrp one will be there.
Click to expand...
Click to collapse
you need to uncheck reboot option from odin, After Pass success message on odin remove cable from your phone then press volume down + home + power off when black screen appears immediately manually boot it to twrp by pressing volume up + Home + Power on and you boot to twrp.
KAASHP said:
you need to uncheck reboot option from odin, After Pass success message on odin remove cable from your phone then press volume down + home + power off when black screen appears immediately manually boot it to twrp by pressing volume up + Home + Power on and you boot to twrp.
Click to expand...
Click to collapse
Oh is that so, ill try this method hope it works. Thanks alot ?
dzkouba said:
I managed to install TWRP on my C9000 HK but it is that of the C900F version
TWRP-3.1.1-0-C900F
how to root please ?
Click to expand...
Click to collapse
Big thanks to dzkouba!!! W/o your report I'd have probably given up because at the time of trying out your solution I've already spent 20+ hours trying to install TWRP on my SM-C9000 (Hong Kong).
For what it's worth, here are the things you will need to do in order to install TWRP on your SM-C9000:
Unlock the bootloader
Enable "OEM Unlock", which can only be done in version 7 (Nougat) or earlier Miracle Box didn't work for me.
Flash a TWRP version that's tailored for SM-C900F (as dzkouba suggested)
Hello All
I have problem with my Axon7 G. I had 8.00 version installed and tried to make a system write option with using a method mentioned in
Official (Beta) Android 8.0.0 V1.30B01 EU Version by NFound thread. I flashed zip mentioned in this tread -ZTE_A7_UniversalBootStack.
Then restart devices and...whats happened....soft (or hard) bricked my phone!!!!!
1. After restart i had a standard warning about unlocked bootloader with yellow fonts . After 5 sec yellow fonts changed into red and wrote my device is corrupt...
2 using vol down i can enter into bootloader mode - then i can choose option like fastboot, recovery,restart and power off.
- pressing recovery and restrt , phone restart and again boot into bootloader mode with option above (cant get into twrp or stock recovery mode)
-pressing fastboot i can enter into this mode .
3 . Use fastboot mode to flash recovery and boot ( fastboot flash recovery recovery.img and fastboot flash boot boot.img)
everything seems ok but...nothing changed , i cant boot into recovery -twrp or stock. Still go back after restart to bootloader menu
4. edl mode.....i can`t enter . Use vol + and vol- and power button then after 3 sec phone went black screen with red light upper left. Applications cant recognize phone in this mode...
somene can help me ???
I also get the warning but I can just continue with the boot. I can't access recovery however. Don't know hot to fix that.
Ok I did this. A7 is working )
I flashed this via fastboot flash file: A2017G_B06_NOUGAT_STOCK_FASTBOOT_EDL.zip then i went into twrp and everything works
Antistar said:
Ok I did this. A7 is working )
I flashed this via fastboot flash file: A2017G_B06_NOUGAT_STOCK_FASTBOOT_EDL.zip then i went into twrp and everything works
Click to expand...
Click to collapse
did you manage to get the error message away?
I got it recently after installing LOS 15.1, but for me everything works fine .
I'm just afraid if the device randomly reboots at night my alarm won't go off in the morning since it's the device is shutting itself down after the 30 second warning.
If you've fixed this can you please detail me through the steps.
HELP , I am stock stuck on logo after I flash panadriod rom now I have flashed pda twrp but twrp is not opening stuck on logo only , I am on fastboot please help flashing twrp but not booting
farhan20 said:
HELP , I am stock stuck on logo after I flash panadriod rom now I have flashed pda twrp but twrp is not opening stuck on logo only , I am on fastboot please help flashing twrp but not booting
Click to expand...
Click to collapse
1. Obviously you need to have your phone bootloader unlocked and enabled USB Debugging.
2. Connect your phone to PC
2. Reboot to Fastboot using Volume Down+Power button
3. On your PC, navigate to the 4PDA TWRP folder
4. Start the Flash_TWRP.bat file (as Administrator just to be sure)
5. Follow the instructions in the CMD window
6. After TWRP Flash, reboot into recovery (Press Volume up Button+Power button)
in TWRP format data
reboot to twrp again in recovery
7. Flashe your Rom of choice
8. Rebooted and let the ROM load (have patience, first time takes pretty long!)
9. Follow and complete setup