Hi, i have a brick phone.
I installed by twrp a stock lollipop italia that this rom before works perfectly in my D805.
The problem is that i installed D805 bootloader of Pro2V5 rom and the phone has bricked. Says secure boot error, but i can to enter in download mode, but the problem is that cannot flash any kdz but thats programs like flashtool, lg support etc not recognize the phone.
The modem driver has intalled correctly but the csc driver and lge android phone not (cannot install them).
When i connect the phone in lg logo and secure boot error, appears many drivers that says if i wish format. seem is qhsusb_bulk error (appears in management)
And i tried with flashtool and tot and appears waiting for connection and not move of this place
How can i to unbrick my phone?.
Any method??
Thanks you
********EDIT*****
I recently use SRK Tool to fix the drives, and looks fine, now not show many partitions and also not show secure boot erro, now oly appears lg logo with secure error and restart permanetly.
What can i do?
Hello Guys, I have LG G2 F320S (Korean Variant) and a few days ago it was stuck in fastboot mode while i was trying to upgrade to Lollipop firmware using LG Flash Tool 2014. And Fastboot commands were working fine but the problem was that some of the partitions had become write-protected so I was unable to erase or reflash those partitions. So, I short circuit the capacitor and I successfully entered Qualcomm 9006 mode with a number of partitions. I used SRKtool to restore partitions (I have this experience in the past so it was easy for me) but here I noticed 1 or 2 partitions were not restored (write-protected) but phone restarted to download mode. When I tried to flash stock firmware then it always stuck in the middle or something and later once again I was stuck in fastmode mode where I started.
I don't know how partitions became write-protected?
Once again I disassembled the cellphone and short-circuit the capacitor to enter Qualcomm 9006 mode and this time, I wanted to remove write-protection from these partitions so I opened "Diskpart" in "cmd" selected LG G2 and performed clean command and format it. Diskpart removed all the partitions gave me a 32GB single partition like a USB Flash. :laugh:
I thought may be after shorting the capacitor, I will get back partitions but this time I got QDLoader 9008 mode. Now whenever I connect phone to PC with or without battery then it is detected in Qualcomm QDloader 9008 mode.
I tried Boarddiag v3.99c but unfortunately this tool doesn't extract .kdz file of my LG G2 F320S korean variant. I tried to extract .tot file of LG G2 D802 (intl variant) and it completed successfully, so the problem is in .kdz file of my cellphone(probably not supported by this tool).
I can extract this .kdz using LGFirmware extract tool but unfortunately it doesn't create "partition.txt" file which is required in boarddiag to flash partitions. I used partition.txt file of LG G2 D802 but it gives error : No DLoad mode when trying to reflash programmer".
Any help would be appreciated.
#StayHomeStaySafe
Boarddiag full and working version helped
I have tried a lot of times to flash the partitions using boarddiag but it failed. It was the problem of the software because almost all versions had missing files. At last, I have found a working version of boarddiag which detects my phone and I am able to flash boot partitions to it. Although all 3 tests completed successfully (AP, EMMC, SDRAM) but still I am stucked, even after flashing all the boot images, I am still stuck in QDLoader 9008 mode and whenever I connect it to PC (with or without battery), it is detected in QDLoader 9008 mode.
Here is the link to the full working version of Boarddiag 3.99 for LG G2:
https://mega.nz/#!SwY2BQ6L!kPZ6s24hdaVj1x5grboFlAksHSwmItblXIcJCCSaeaw
(mega is blocked in many countries so you may have to use proxy/vpn to open this link)
Here is the result of all 3 tests. Please tell me whats the problem. SDRAM result is FAIL but why so?
https://ibb.co/6ntQwsv
Now I am able to enter "Download Mode" but unable to flash stock or any other firmware. I tried flashing with 2 softwares:
1. LG UP-G2-G3....This software gives error at 6% (at LAF read) as shown in picture below :
https://ibb.co/zXpDcjt
2. LG Flash tool 2014.... This software gives error at 4% by saying "Unable to Establish Connection" though connection is fine because phone is detected in Device Manager and in Download Mode "It shows signs that communication is successful but it wont flash.
salmanzafar said:
Now I am able to enter "Download Mode" but unable to flash stock or any other firmware. I tried flashing with 2 softwares:
1. LG UP-G2-G3....This software gives error at 6% (at LAF read) as shown in picture below :
https://ibb.co/zXpDcjt
2. LG Flash tool 2014.... This software gives error at 4% by saying "Unable to Establish Connection" though connection is fine because phone is detected in Device Manager and in Download Mode "It shows signs that communication is successful but it wont flash.
Click to expand...
Click to collapse
Did you try the TOT flash method already? It worked best for me, when I restored my phone from scratch 2 days ago.
rootarded said:
Did you try the TOT flash method already? It worked best for me, when I restored my phone from scratch 2 days ago.
Click to expand...
Click to collapse
Dear I have tried two methods. I tried LGUP and LG Flash Tools 2014. But both fails. Unfortunately, no TOT file is available for my LG G2 because its Korean variant (F320S) and it has only .kdz firmwares available.
QDLoader 9008 mode
Now, my phone is not entering download mode. It is displayed as QDLoader 9008 mode when connected to PC. Check the screenshot here : https://ibb.co/yk3VSbS
I have the working version of boarddiag but sometimes it passes all 3 tests and sometimes fails EMMC test ad sometimes SDRAM test is not completed successfully.
I watched some tutorials for Qualcomm phones on how to get them into diagnostic mode. In Device Manager you should get a Qualcomm device with a certain COM port.
I was never able to get a Huawei Y7 Prime 2017 into diagnostic mode. The phone is rooted and ADB has SU access. I tried:
- Rebooting into EDL mode with adb reboot edl : normal reboot
- sys.usb.config diag,adb: did nothing
- *#*#2846579#*#* and then manufacture mode: nothing
What I want is to get the diagnostic port, if/when I manage to put it into diagnostic mode. Any ideas would be very welcome!
Please help me.
The problem is that after flashing the rom via odin failed, my Samsung G530H was bricked and can't boot into any more modes like download mode and I tried entering EDL mode when it was banned. go to the computer in the QDloader 9008 port manager can anyone help me unbrick this device (((((
Dear fellow members,
The camera app in my father's Poco M3 couldn't connect to the camera. So, I decided to flash a fastboot from Mi Flash Tool. Unfortunately, I picked the wrong firmware to flash, i.e., flashed the global version instead of the Indian version. Now the device is bricked, I can't boot into fastboot again and am stuck in EDL mode. When connected to a PC the device is recognized as "Qualcomm HS-USB QDLoader 908 (COM20)"
Tried flashing the Indian firmware using Mi Flash Tool. Mi Flash Tool asks for an authorized mi account and the process is stuck in "edl authentication".
Currently, I'm draining the battery using a rubber band+cotton bud in hope that it would boot into fastboot after showing the charging logo once the battery is drained.
The Bootloader in Unlocked
The Previous Firmware was Indian
Windows 10