[GUIDE] [6.3.3] 1st Gen Kindle Drivers, Rooting, Bootloaders & Recovery, and OtterX
Hello everyone! I am new to working with the Kindle Fire, however, I am by no means new to rooting and tinkering with my devices. Yesterday, I inherited a Kindle Fire with software version 6.3.3 from my brother and I was completely unsure of how to root the device. I am writing this guide because many of the existing guides were unclear and lead me to screw up multiple times. In addition, some claimed to work with the 6.3.3 software version, however, they were designed for an older version of the firmware and would not actually work.
I WILL NOT BE HELD LIABLE IF YOU BRICK YOUR DEVICE USING THESE INSTRUCTIONS! FOLLOW ALL DIRECTIONS CAREFULLY AND REMEMBER TO BACKUP YOUR DATA! YOUR DATA WILL BE WIPED DURING THIS PROCESS. ONLY CONTINUE IF YOU UNDERSTAND THE RISKS! THESE INSTRUCTIONS ARE IN SEQUENTIAL ORDER, FOLLOW EACH STEP! YOU CANNOT SKIP ANY OF THE STEPS!
0. Checking MD5 Hashes
It is very important to check the MD5 hash of every file that you download for this guide. You may use your favorite MD5 checksum utility. Personally, I prefer using this tool created by Microsoft because it is lightweight and extremely fast. Unfortunately, it does take some knowledge of the Command Prompt to use. To begin, download the file and extract it to any folder that you would like. To use the tool, place the file that you are checking within the same folder as the tool. Then, hold shift on your keyboard and right click. Choose the option to open a new Command Prompt window. Then, issue the following commands:
Code:
fciv.exe <exact name of file you are checking>
This will tell you the MD5 checksum of the file that you are checking and you will want to compare it to the value that is listed with the download. Again, you will want to do this for every file that is downloaded for this guide to ensure that you do not damage your device or need to restart the process.
1. Drivers
One problem that I faced while rooting my Kindle Fire was the installation of drivers. Basically, this guide requires you to use unsigned drivers that Windows will refuse to install under normal circumstances. On Windows 8, Windows 8.1, and in the Windows 10 Technical preview, you need to enable Test Mode. Although you can just disable the driver signature verification for one boot, I found this inefficient because I needed to tinker with the drivers multiple times, with each successive installation requiring a reboot of the computer.
To enable Test Mode on Windows 8, Windows 8.1, and Windows 10 Technical Preview, you need some experience with the Command Prompt. Open an Administrative Command Prompt by typing "cmd" into the Start menu and right clicking on the Command Prompt icon. From there, choose the option to open the program with Administrative privileges. Then, issue the following commands:
Code:
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
Reboot your computer.
Next, you will want to download the KFU utility from this XDA developer thread. We will NOT be using the Kindle Fire Utility for this guide because I was unable to get it working with 6.3.3, instead we will be using the included set of drivers because they worked relatively well with this process. After downloading the latest version of KFU, extract it to a folder on your Desktop. Unplug your Kindle Fire if it is plugged in to your computer or the drivers may not install correctly. You will want to open the "install_drivers.bat" file and follow the prompts. One prompt will ask you if you want to run the unsigned driver, you should choose "Install this driver software anyway!". Please restart your computer before continuing with this guide!
Now, you may plug in your Kindle Fire. Before continuing, please ensure that the installation of applications is allowed on the device by opening the settings drop down, clicking "More", and clicking on "Device". From there, check the box that allows the installation of applications. Next, you will want to navigate to the folder in the "Kindle Fire Utility" called "Tools". From here, hold shift on your keyboard and right click. Then, choose the option to open a Command Prompt window. We are going to test to make sure that the Kindle Fire is recognized by the "adb" program. To do this, we are going to issue the following commands:
Code:
adb kill-server
adb usb
adb devices
If you typed these commands correctly, any old instances of the "adb" server will be destroyed. Then, it will start a new server that will work with USB devices. Finally, it will list the connected devices. If the driver installation has succeeded, you will see the serial number of your Kindle Fire as well as an "Online" status. If you do not see your device or it is not marked as "Online", you may need to repeat the steps for installing the drivers. Do NOT continue until these commands list your device as "Online" because it could theoretically damage the device. If you are unable to get these drivers working, I recommend using the GhostBuster utility to remove old Kindle Fire and Android phone drivers.
2. Rooting the Device
This is where you want to back up anything important on the device!
Since I was unable to find an official root method from the Kindle Fire community for patch 6.3.3, I looked into using other methods. Using SafeRoot was suggested by some people and it worked very well for my Kindle Fire. So, to continue, please download the SafeRoot package from this XDA Developers link. Extract these files to a folder of your choice, preferably somewhere that is easy to access. We are NOT using the Kindle Fire Utility for this step because it simply was not compatible with software version 6.3.3.
Now, run the "install.bat" file and follow ALL of the on-screen instructions. The utility will ask you if you wish to install Busybox on your device. Busybox is a powerful utility that combines many powerful Unix utilities into a single file. You can read more about it here. You will want to choose yes when it asks you if it can install Busybox. After following all of the instructions, you should have a SuperUser application on your device that allows you run root commands!
It is NORMAL for the SafeRoot utility to show a lot of errors towards the end relating to read only files. If there are any other errors, your device may not be rooted!
3. Flashing FFF and the TWRP Recovery (Non-OtterX)
First, you will want to download the FBMode file. This file will allow your device to boot into the Fastboot mode, which allows you to flash new bootloader and recovery images. In addition, you will want to download the FireFireFire bootloader image that we will be flashing to the device. You will also need a custom recovery for this device, which can be found here. If you ignore everything else in this guide, just please remember to MD5 check ALL of these files! This is extremely important because a bad flash could BRICK your device!
Extract each of these files to the "Tools" folder inside of the Kindle Fire Utility folder that we used earlier to install the driver. Again, open a Command Prompt window inside of the Tools folder by holding shift and right clicking, then choosing the option to open a new Command Prompt window. Type these commands EXACTLY to copy the "fbmode" file to the device. This file will put the device in Fastboot mode.
Code:
adb push fbmode /data/local/tmp
adb shell chmod 755 /data/local/tmp/fbmode
adb shell
You will notice that the Command Prompt window looks slightly different because we are now in a shell for the device. This means we are directly issuing commands to the device! Type the following commands exactly to reboot the device in Fastboot mode. Remember, the "exit" command will need to be typed TWICE!
Code:
su
cd /data/local/tmp
./fbmode
exit
exit
adb reboot
If you did everything correctly, you will now be in Fastboot mode! No, you did not brick your Kindle. The device will not boot into the OS until we tell it to so it WILL remain at the Kindle Fire logo indefinitely, even upon rebooting the device. Depending on your operating system, you may need to toy with the driver installation to 'see' the device again.
Test to make sure that the Kindle still responds to commands before continuing by issuing the following command within the same command prompt window that we used previously to copy the "fbmode" file.
Code:
fastboot -i 0x1949 reboot
The kindle should reboot into the Fastboot mode again! If not, please use this post to get the drivers working. In my case, the device responded to the reboot command, however, it did NOT show up when I checked the connected devices by issuing the following command:
Code:
fastboot -i 0x1949 devices
If all is well and the Kindle rebooted, it is time to flash the bootloader and recovery images! Remember to check the MD5 hash for these files! You WILL need to know the name of your recovery image, it should be named something very similar to "openrecovery-twrp-2.2.2.1-blaze.img".
This is NOT the FireFireFire file, which is named "fff-u-boot_v1.5.bin". DO NOT flash the FireFireFire file to the recovery partition! If you get any errors during this part of the process, DO NOT continue! You may brick your device!
Code:
fastboot -i 0x1949 flash recovery <REPLACE ME WITH THE NAME OF RECOVERY IMAGE FILE>
Next, we will flash the bootloader image! Issue the following command to the device using the same Command Prompt window that we used to flash the recovery image.
Code:
fastboot -i 0x1949 flash bootloader fff-u-boot_v1.5.bin
Now, we will take the device out of Fastboot mode and make sure that our flashes were successful! If you got any errors during the flashing process, DO NOT continue! You may brick your device!
Code:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
When you reboot, you should get a new Kindle Fire logo that will be White & Blue. Follow the on-screen instructions to enter the Recovery mode and make sure that the Team Win Recovery image boots. If it does, congratulations! You now have a custom recovery and bootloader on your Kindle device!
4. Installing OtterX Bootloader and Recovery Images
Now that you have a custom bootloader and recovery image flashed, you can now experiment with the OtterX project if you wish. Remember that the OtterX project fundamentally alters the device and it may be extremely difficult to revert these changes to the device! OtterX recoveries, boot loaders, and ROMs are not compatible with stock recoveries, boot loaders, and ROMs. If you still wish to use the device as a Kindle, do not proceed!
Now that the disclaimer is out of the way, let's continue! To continue, you will need the OtterX Bootloader and a copy of the TWRP Recovery for OtterX (Fundamentally different than the TWRP recovery from the last step!). Again, REMEMBER TO CHECK THE MD5 CHECKSUMS OF THESE FILES! A corrupted file could brick your device!
To make sure that the wrong recovery and bootloader are not applied, delete the old copies from your Tools folder inside of the Kindle Fire Utility folder. Then, copy over the OtterX versions of the bootloader and recovery images. Again, open a Command Prompt window inside of the Tools folder by holding shift and right clicking, then choosing the option to open a new Command Prompt window. Enter the following commands exactly!
You will need to know the name of your bootloader file. It should be named similarly to "otterx-u-boot_v2.05.bin". Make sure it says OtterX in the name of the file! Power on the device to the Kindle Fire screen and issue the following command on your computer.
Code:
fastboot flash bootloader <Name of OtterX Bootloader File>
Now, reboot the device after the flash has fully completed! You should see a new boot logo, meaning that the flash was successful! Before we continue, we will need to change the partition layout of the device. This will erase all of your files that exist on the device, you should have backed then up a few steps ago! At the bootloader screen, short press the power button to enter the boot menu. Then, use short presses of the power button to navigate to the advanced menu. Then, use a long press to enter that menu. Now, use short presses to navigate down to the "Partition Mode" button and use a long press to enter the submenu. Use short presses to press the navigate down to the Confirm button, and finally use one last long press to start the process.
After this has been completed, reboot the device. Again at the Kindle Fire screen, enter the following command on your computer.
You will need to know the name of your recovery file. It should be named similarly to "otterx-twrp-2.7.1.0-recovery.img". Make sure it says OtterX in the name of the file!
Code:
fastboot flash recovery <Name of Recovery Image>
fastboot oem recovery
After issuing both commands, you should see the TWRP recovery screen again! If you do, congratulations! You have flashed the OtterX recovery and bootloader images to your device,
5. Installing OtterX ROMs
I have found that the easiest way to install ROMs to this device is through a function called "adb sideloading". To begin, you will need an OtterX ROM file. I personally recommend Cyanogenmod because it seems fairly stable on this tablet (with my few hours of experience) and I use it as a daily driver on my Galaxy S3.
To begin, grab a copy of ANY OtterX ROM file. You can download Cyanogenmod ROMs from this website. Next, you will also want to download a Google Apps package for your device. You can get that from this website as well.
From the TWRP recovery menu, select the "Wipe" option and then choose "Factory Reset". Follow the onscreen prompts to reset the files on your device. If you get any errors, mount the partitions shown in the "Mounts" menu on the main screen.
Next, go to the Advanced section and choose "ADB Sideload". You should choose the boxes to wipe both caches. To continue, you will need a more up-to-date version of the adb program. You will want just the SDK tools, not the full Android Studio. You can download those tools from this website. After the tools are installed, open up the SDK manager and choose the "Install x Packages" button at the bottom to update the tools. After this is complete, navigate to "C:\Program Files (x86)\Android\android-sdk\platform-tools" on your hard drive. If you are using a 32 bit computer, navigate to "C:\Program Files\Android\android-sdk\platform-tools". Copy your ROM image to this folder and rename it something easy to work with, such as "CM11-OtterX-M12.zip".
Now, you will want to slide the bar across on your device that says "Swipe to Sideload", as well as open a new Command Prompt window on your computer. You can do this by holding shift and right clicking "Open New Command Prompt Window". Now, you will want to issue the following command to make sure your computer can see your Kindle device.
Code:
adb devices
Your device serial number should be listed here and it should say "Sideload" next to the name.
Now, you will want to issue the following command:
Code:
adb sideload <Name of ROM File ZIP>
Now, you will need to wait about 5 minutes while your device is flashed with a new ROM. In my case, the ROM stopped flashing at around 47% with an "Unknown Command" error, however, my device finished the flash okay and the ROM booted just fine. As long as your TWRP recovery shows "Success!", the ROM flash was probably okay. If the ROM flash had failed, you would still be able to try the flash again without harming anything.
You can now go back to the main menu and choose to reboot your device. If the flash was successful, you should see a boot logo for whichever ROM you chose to install. Remember, the initial boot can take a long time.
After verifying that the ROM installed correctly, copy the Google Apps package to your device's internal storage. Depending on which ROM you used, the device should show up as an MTP compatible device in Windows when powered on. Then, reboot into the recovery menu and choose "Install". Then, choose the Google Apps package that you copied to the device to install them. Upon rebooting, the device will update roughly 30-50 apps depending on how much bloatware is installed with your ROM. After that is complete, you will have access to the Google Play store and many useful apps.
Congratulations, you just installed an OtterX rom onto your device!
We need a new update for 2016
ajwgeek said:
Hello everyone! I am new to working with the Kindle Fire, however, I am by no means new to rooting and tinkering with my devices. Yesterday, I inherited a Kindle Fire with software version 6.3.3 from my brother and I was completely unsure of how to root the device. I am writing this guide because many of the existing guides were unclear and lead me to screw up multiple times. In addition, some claimed to work with the 6.3.3 software version, however, they were designed for an older version of the firmware and would not actually work.
I WILL NOT BE HELD LIABLE IF YOU BRICK YOUR DEVICE USING THESE INSTRUCTIONS! FOLLOW ALL DIRECTIONS CAREFULLY AND REMEMBER TO BACKUP YOUR DATA! YOUR DATA WILL BE WIPED DURING THIS PROCESS. ONLY CONTINUE IF YOU UNDERSTAND THE RISKS! THESE INSTRUCTIONS ARE IN SEQUENTIAL ORDER, FOLLOW EACH STEP! YOU CANNOT SKIP ANY OF THE STEPS!
0. Checking MD5 Hashes
It is very important to check the MD5 hash of every file that you download for this guide. You may use your favorite MD5 checksum utility. Personally, I prefer using this tool created by Microsoft because it is lightweight and extremely fast. Unfortunately, it does take some knowledge of the Command Prompt to use. To begin, download the file and extract it to any folder that you would like. To use the tool, place the file that you are checking within the same folder as the tool. Then, hold shift on your keyboard and right click. Choose the option to open a new Command Prompt window. Then, issue the following commands:
Code:
fciv.exe <exact name of file you are checking>
This will tell you the MD5 checksum of the file that you are checking and you will want to compare it to the value that is listed with the download. Again, you will want to do this for every file that is downloaded for this guide to ensure that you do not damage your device or need to restart the process.
1. Drivers
One problem that I faced while rooting my Kindle Fire was the installation of drivers. Basically, this guide requires you to use unsigned drivers that Windows will refuse to install under normal circumstances. On Windows 8, Windows 8.1, and in the Windows 10 Technical preview, you need to enable Test Mode. Although you can just disable the driver signature verification for one boot, I found this inefficient because I needed to tinker with the drivers multiple times, with each successive installation requiring a reboot of the computer.
To enable Test Mode on Windows 8, Windows 8.1, and Windows 10 Technical Preview, you need some experience with the Command Prompt. Open an Administrative Command Prompt by typing "cmd" into the Start menu and right clicking on the Command Prompt icon. From there, choose the option to open the program with Administrative privileges. Then, issue the following commands:
Code:
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
Reboot your computer.
Next, you will want to download the KFU utility from this XDA developer thread. We will NOT be using the Kindle Fire Utility for this guide because I was unable to get it working with 6.3.3, instead we will be using the included set of drivers because they worked relatively well with this process. After downloading the latest version of KFU, extract it to a folder on your Desktop. Unplug your Kindle Fire if it is plugged in to your computer or the drivers may not install correctly. You will want to open the "install_drivers.bat" file and follow the prompts. One prompt will ask you if you want to run the unsigned driver, you should choose "Install this driver software anyway!". Please restart your computer before continuing with this guide!
Now, you may plug in your Kindle Fire. Before continuing, please ensure that the installation of applications is allowed on the device by opening the settings drop down, clicking "More", and clicking on "Device". From there, check the box that allows the installation of applications. Next, you will want to navigate to the folder in the "Kindle Fire Utility" called "Tools". From here, hold shift on your keyboard and right click. Then, choose the option to open a Command Prompt window. We are going to test to make sure that the Kindle Fire is recognized by the "adb" program. To do this, we are going to issue the following commands:
Code:
adb kill-server
adb usb
adb devices
If you typed these commands correctly, any old instances of the "adb" server will be destroyed. Then, it will start a new server that will work with USB devices. Finally, it will list the connected devices. If the driver installation has succeeded, you will see the serial number of your Kindle Fire as well as an "Online" status. If you do not see your device or it is not marked as "Online", you may need to repeat the steps for installing the drivers. Do NOT continue until these commands list your device as "Online" because it could theoretically damage the device. If you are unable to get these drivers working, I recommend using the GhostBuster utility to remove old Kindle Fire and Android phone drivers.
2. Rooting the Device
This is where you want to back up anything important on the device!
Since I was unable to find an official root method from the Kindle Fire community for patch 6.3.3, I looked into using other methods. Using SafeRoot was suggested by some people and it worked very well for my Kindle Fire. So, to continue, please download the SafeRoot package from this XDA Developers link. Extract these files to a folder of your choice, preferably somewhere that is easy to access. We are NOT using the Kindle Fire Utility for this step because it simply was not compatible with software version 6.3.3.
Now, run the "install.bat" file and follow ALL of the on-screen instructions. The utility will ask you if you wish to install Busybox on your device. Busybox is a powerful utility that combines many powerful Unix utilities into a single file. You can read more about it here. You will want to choose yes when it asks you if it can install Busybox. After following all of the instructions, you should have a SuperUser application on your device that allows you run root commands!
It is NORMAL for the SafeRoot utility to show a lot of errors towards the end relating to read only files. If there are any other errors, your device may not be rooted!
3. Flashing FFF and the TWRP Recovery (Non-OtterX)
First, you will want to download the FBMode file. This file will allow your device to boot into the Fastboot mode, which allows you to flash new bootloader and recovery images. In addition, you will want to download the FireFireFire bootloader image that we will be flashing to the device. You will also need a custom recovery for this device, which can be found here. If you ignore everything else in this guide, just please remember to MD5 check ALL of these files! This is extremely important because a bad flash could BRICK your device!
Extract each of these files to the "Tools" folder inside of the Kindle Fire Utility folder that we used earlier to install the driver. Again, open a Command Prompt window inside of the Tools folder by holding shift and right clicking, then choosing the option to open a new Command Prompt window. Type these commands EXACTLY to copy the "fbmode" file to the device. This file will put the device in Fastboot mode.
Code:
adb push fbmode /data/local/tmp
adb shell chmod 755 /data/local/tmp/fbmode
adb shell
You will notice that the Command Prompt window looks slightly different because we are now in a shell for the device. This means we are directly issuing commands to the device! Type the following commands exactly to reboot the device in Fastboot mode. Remember, the "exit" command will need to be typed TWICE!
Code:
su
cd /data/local/tmp
./fbmode
exit
exit
adb reboot
If you did everything correctly, you will now be in Fastboot mode! No, you did not brick your Kindle. The device will not boot into the OS until we tell it to so it WILL remain at the Kindle Fire logo indefinitely, even upon rebooting the device. Depending on your operating system, you may need to toy with the driver installation to 'see' the device again.
Test to make sure that the Kindle still responds to commands before continuing by issuing the following command within the same command prompt window that we used previously to copy the "fbmode" file.
Code:
fastboot -i 0x1949 reboot
The kindle should reboot into the Fastboot mode again! If not, please use this post to get the drivers working. In my case, the device responded to the reboot command, however, it did NOT show up when I checked the connected devices by issuing the following command:
Code:
fastboot -i 0x1949 devices
If all is well and the Kindle rebooted, it is time to flash the bootloader and recovery images! Remember to check the MD5 hash for these files! You WILL need to know the name of your recovery image, it should be named something very similar to "openrecovery-twrp-2.2.2.1-blaze.img".
This is NOT the FireFireFire file, which is named "fff-u-boot_v1.5.bin". DO NOT flash the FireFireFire file to the recovery partition! If you get any errors during this part of the process, DO NOT continue! You may brick your device!
Code:
fastboot -i 0x1949 flash recovery <REPLACE ME WITH THE NAME OF RECOVERY IMAGE FILE>
Next, we will flash the bootloader image! Issue the following command to the device using the same Command Prompt window that we used to flash the recovery image.
Code:
fastboot -i 0x1949 flash bootloader fff-u-boot_v1.5.bin
Now, we will take the device out of Fastboot mode and make sure that our flashes were successful! If you got any errors during the flashing process, DO NOT continue! You may brick your device!
Code:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
When you reboot, you should get a new Kindle Fire logo that will be White & Blue. Follow the on-screen instructions to enter the Recovery mode and make sure that the Team Win Recovery image boots. If it does, congratulations! You now have a custom recovery and bootloader on your Kindle device!
4. Installing OtterX Bootloader and Recovery Images
Now that you have a custom bootloader and recovery image flashed, you can now experiment with the OtterX project if you wish. Remember that the OtterX project fundamentally alters the device and it may be extremely difficult to revert these changes to the device! OtterX recoveries, boot loaders, and ROMs are not compatible with stock recoveries, boot loaders, and ROMs. If you still wish to use the device as a Kindle, do not proceed!
Now that the disclaimer is out of the way, let's continue! To continue, you will need the OtterX Bootloader and a copy of the TWRP Recovery for OtterX (Fundamentally different than the TWRP recovery from the last step!). Again, REMEMBER TO CHECK THE MD5 CHECKSUMS OF THESE FILES! A corrupted file could brick your device!
To make sure that the wrong recovery and bootloader are not applied, delete the old copies from your Tools folder inside of the Kindle Fire Utility folder. Then, copy over the OtterX versions of the bootloader and recovery images. Again, open a Command Prompt window inside of the Tools folder by holding shift and right clicking, then choosing the option to open a new Command Prompt window. Enter the following commands exactly!
You will need to know the name of your bootloader file. It should be named similarly to "otterx-u-boot_v2.05.bin". Make sure it says OtterX in the name of the file! Power on the device to the Kindle Fire screen and issue the following command on your computer.
Code:
fastboot flash bootloader <Name of OtterX Bootloader File>
Now, reboot the device after the flash has fully completed! You should see a new boot logo, meaning that the flash was successful! Before we continue, we will need to change the partition layout of the device. This will erase all of your files that exist on the device, you should have backed then up a few steps ago! At the bootloader screen, short press the power button to enter the boot menu. Then, use short presses of the power button to navigate to the advanced menu. Then, use a long press to enter that menu. Now, use short presses to navigate down to the "Partition Mode" button and use a long press to enter the submenu. Use short presses to press the navigate down to the Confirm button, and finally use one last long press to start the process.
After this has been completed, reboot the device. Again at the Kindle Fire screen, enter the following command on your computer.
You will need to know the name of your recovery file. It should be named similarly to "otterx-twrp-2.7.1.0-recovery.img". Make sure it says OtterX in the name of the file!
Code:
fastboot flash recovery <Name of Recovery Image>
fastboot oem recovery
After issuing both commands, you should see the TWRP recovery screen again! If you do, congratulations! You have flashed the OtterX recovery and bootloader images to your device,
5. Installing OtterX ROMs
I have found that the easiest way to install ROMs to this device is through a function called "adb sideloading". To begin, you will need an OtterX ROM file. I personally recommend Cyanogenmod because it seems fairly stable on this tablet (with my few hours of experience) and I use it as a daily driver on my Galaxy S3.
To begin, grab a copy of ANY OtterX ROM file. You can download Cyanogenmod ROMs from this website. Next, you will also want to download a Google Apps package for your device. You can get that from this website as well.
From the TWRP recovery menu, select the "Wipe" option and then choose "Factory Reset". Follow the onscreen prompts to reset the files on your device. If you get any errors, mount the partitions shown in the "Mounts" menu on the main screen.
Next, go to the Advanced section and choose "ADB Sideload". You should choose the boxes to wipe both caches. To continue, you will need a more up-to-date version of the adb program. You will want just the SDK tools, not the full Android Studio. You can download those tools from this website. After the tools are installed, open up the SDK manager and choose the "Install x Packages" button at the bottom to update the tools. After this is complete, navigate to "C:\Program Files (x86)\Android\android-sdk\platform-tools" on your hard drive. If you are using a 32 bit computer, navigate to "C:\Program Files\Android\android-sdk\platform-tools". Copy your ROM image to this folder and rename it something easy to work with, such as "CM11-OtterX-M12.zip".
Now, you will want to slide the bar across on your device that says "Swipe to Sideload", as well as open a new Command Prompt window on your computer. You can do this by holding shift and right clicking "Open New Command Prompt Window". Now, you will want to issue the following command to make sure your computer can see your Kindle device.
Code:
adb devices
Your device serial number should be listed here and it should say "Sideload" next to the name.
Now, you will want to issue the following command:
Code:
adb sideload <Name of ROM File ZIP>
Now, you will need to wait about 5 minutes while your device is flashed with a new ROM. In my case, the ROM stopped flashing at around 47% with an "Unknown Command" error, however, my device finished the flash okay and the ROM booted just fine. As long as your TWRP recovery shows "Success!", the ROM flash was probably okay. If the ROM flash had failed, you would still be able to try the flash again without harming anything.
You can now go back to the main menu and choose to reboot your device. If the flash was successful, you should see a boot logo for whichever ROM you chose to install. Remember, the initial boot can take a long time.
After verifying that the ROM installed correctly, copy the Google Apps package to your device's internal storage. Depending on which ROM you used, the device should show up as an MTP compatible device in Windows when powered on. Then, reboot into the recovery menu and choose "Install". Then, choose the Google Apps package that you copied to the device to install them. Upon rebooting, the device will update roughly 30-50 apps depending on how much bloatware is installed with your ROM. After that is complete, you will have access to the Google Play store and many useful apps.
Congratulations, you just installed an OtterX rom onto your device!
Click to expand...
Click to collapse
We need new links for kindle fire first gen 6.3.4 . these methods available don't work. thank you
ataraxioss said:
We need new links for kindle fire first gen 6.3.4 . these methods available don't work. thank you
Click to expand...
Click to collapse
no, this still works with 6.3.4
Sent from my KFFOWI using Tapatalk
---------- Post added at 06:55 PM ---------- Previous post was at 06:54 PM ----------
there is one link to goo.im which is down
With the Fall of Goo.im I will be posting Mirrors OtterX files here:
Otter X Twrp and Bootloader Mirrors
Sent from my KFFOWI using Tapatalk
I've just tried it
Still not working on my kindle fire. sounds to be rooted but can't install twrp.
i was hoping to flash it with Miui 7.
thank you for your precious time, i wish the old links in kindle fire utility could still work.
ataraxioss said:
Still not working on my kindle fire. sounds to be rooted but can't install twrp.
i was hoping to flash it with Miui 7.
thank you for your precious time, i wish the old links in kindle fire utility could still work.
Click to expand...
Click to collapse
did you verify root? try root checker
Sent from my KFFOWI using Tapatalk
reply
sd_shadow said:
did you verify root? try root checker
Sent from my KFFOWI using Tapatalk
Click to expand...
Click to collapse
once it is frozen on "trying to disable knox.." nothing goes right after that. the kindle fire does not reboot and i guess supersu is not updating either.
Ps: i have rooted and installed twrp many times before, then i did a factory reset on the kindle fire.
ataraxioss said:
once it is frozen on "trying to disable knox.." nothing goes right after that. the kindle fire does not reboot and i guess supersu is not updating either.
Ps: i have rooted and installed twrp many times before, then i did a factory reset on the kindle fire.
Click to expand...
Click to collapse
Factory reset doesn't unroot, just reinstall supersu app
Sent from my XT1060 using Tapatalk
So I got up to this point.
Test to make sure that the Kindle still responds to commands before continuing by issuing the following command within the same command prompt window that we used previously to copy the "fbmode" file.
Code:
fastboot -i 0x1949 reboot
The kindle should reboot into the Fastboot mode again! If not, please use this post to get the drivers working. In my case, the device responded to the reboot command, however, it did NOT show up when I checked the connected devices by issuing the following command:
Code:
fastboot -i 0x1949 devices
If all is well and the Kindle rebooted, it is time to flash the bootloader and recovery images! Remember to check the MD5 hash for these files! You WILL need to know the name of your recovery image, it should be named something very similar to "openrecovery-twrp-2.2.2.1-blaze.img". "
Click to expand...
Click to collapse
The kindle won't restart. When I plug it into my computer I get the error "The last USB device you connected to this computer malfunctioned, and Windows does not recognize it." The kindle is stuck on the start up screen where it says "Kindle Fire." Any help would be greatly appreciated. I know nothing about any of this stuff so I am stumped from here on out.
Also nothing is showing up in device manager that is related to the Kindle.
thealy1234 said:
So I got up to this point.
Test to make sure that the Kindle still responds to commands before continuing by issuing the following command within the same command prompt window that we used previously to copy the "fbmode" file.
Code:
fastboot -i 0x1949 reboot
The kindle should reboot into the Fastboot mode again! If not, please use this post to get the drivers working. In my case, the device responded to the reboot command, however, it did NOT show up when I checked the connected devices by issuing the following command:
Code:
fastboot -i 0x1949 devices
If all is well and the Kindle rebooted, it is time to flash the bootloader and recovery images! Remember to check the MD5 hash for these files! You WILL need to know the name of your recovery image, it should be named something very similar to "openrecovery-twrp-2.2.2.1-blaze.img". "
The kindle won't restart. When I plug it into my computer I get the error "The last USB device you connected to this computer malfunctioned, and Windows does not recognize it." The kindle is stuck on the start up screen where it says "Kindle Fire." Any help would be greatly appreciated. I know nothing about any of this stuff so I am stumped from here on out.
Also nothing is showing up in device manager that is related to the Kindle.
Click to expand...
Click to collapse
try a different USB port or cable
Sent from my Motorola XT1060 using XDA Labs
sd_shadow said:
try a different USB port or cable
Sent from my Motorola XT1060 using XDA Labs
Click to expand...
Click to collapse
This was the problem. Turns out this doesn't work when the kindle is plugged into a USB 3.0 port.
That being solved, I now have a different problem. I get the following error when I try and push the recovery image onto my kindle after I added the Otterbox bootloader file: "target reported max download size of 402653184 bytes error: cannot load 'recovery.img': No error."
(I renamed the file to recovery.img on the advice of someone else)
Also note that I had to get the otter recovery image from a different source than what was listed in the guide, for the provided link was broken.
Any ideas would be appreciated.
Thanks
thealy1234 said:
This was the problem. Turns out this doesn't work when the kindle is plugged into a USB 3.0 port.
That being solved, I now have a different problem. I get the following error when I try and push the recovery image onto my kindle after I added the Otterbox bootloader file: "target reported max download size of 402653184 bytes error: cannot load 'recovery.img': No error."
(I renamed the file to recovery.img on the advice of someone else)
Also note that I had to get the otter recovery image from a different source than what was listed in the guide, for the provided link was broken.
Any ideas would be appreciated.
Thanks
Click to expand...
Click to collapse
[6.3.4][6.3.3] Flashing FFF and TWRP without Fastboot Cable with Video
Sent from my XT1060 using Tapatalk
sd_shadow said:
[6.3.4][6.3.3] Flashing FFF and TWRP without Fastboot Cable with Video
Sent from my XT1060 using Tapatalk
Click to expand...
Click to collapse
I have followed that guide to the T and I still get that error. It worked just fine when I was installed the TWRP recovery.
For some reason when I am trying to install the otterx twrp version, I am getting that error returned to me.
thealy1234 said:
I have followed that guide to the T and I still get that error. It worked just fine when I was installed the TWRP recovery.
For some reason when I am trying to install the otterx twrp version, I am getting that error returned to me.
Click to expand...
Click to collapse
try OtterX bootloader and OtterX twrp from my post
OtterX files here:
Otter X Twrp and Bootloader Mirrors
Sent from my XT1060 using Tapatalk
The 2.8.5.0 file that you provide worked. One more step closer...
I appreciate the help.
---------- Post added at 10:45 PM ---------- Previous post was at 10:26 PM ----------
I just can't win today.
Now I am stuck because TWRP cannot mount /data for some reason...
thealy1234 said:
The 2.8.5.0 file that you provide worked. One more step closer...
I appreciate the help.
---------- Post added at 10:45 PM ---------- Previous post was at 10:26 PM ----------
I just can't win today.
Now I am stuck because TWRP cannot mount /data for some reason...
Click to expand...
Click to collapse
mount data is ify with OtterX, try adb push with OtterX twrp 2.7.1.0
---------- Post added at 01:11 AM ---------- Previous post was at 01:10 AM ----------
Started a Thread [How To] Fix OtterX Install Errors, Partition sizes, Unable to Mount System... with some possible fixes for those having issues since converting to OtterX, with pushing files, failure to mount system errors when installing Lollipop Roms...
After your help + plenty of head scratching I finally managed to install everything 100%.
Biggest hangup was before I realized this process wouldn't work on a USB 3.0 port....
I'm having an issue with being able to actually install drivers on my computer with Windows 10. I attempted to follow the guide but I am getting denied on an error with "bcdedit -set TESTSINGING ON".
"An error has occurred setting the element data. The value is protected by Secure Boot policy and cannot be modified or deleted."
Any advice for a workaround on installing the drivers?
Finally I got myself to root and unlock bootloader of my Thor Kindles. I've been lurking for few years. Here is the steps:-
1. Install Kingroot from Kingroot website (https://kingroot.net/) and root the phone. I got it first try. But some people are saying they need 8 tries to work. Some even report success after 20 tries.
2. Flash TWRP and Unlock bootloaders. Instruction in https://forum.xda-developers.com/ki...r-firmware-t3463982/post70881555#post70881555. Instruction in this post is better than the first post (OP) in the thread. The step is:-
a) install ADB driver and install Kindle Fire USB driver
b) put get_code.bat and unlock.bat in adb.exe directory. Put aboot and cubed twrp in /sdcard/
b) create unlock.code with get_code.bat
c) flash aboot and cubed twrp with this command in DOS command prompt in adb.exe directory:-
adb shell
su
dd if=/sdcard/twrp_cubed.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
dd if=/sdcard/aboot_vuln.mbn of=/dev/block/platform/msm_sdcc.1/by-name/aboot
Click to expand...
Click to collapse
d) make sure check the Android ADB Composite driver is properly install in Device Manager
e) execute unlock.bat
f) reboot, press UP + power to boot into TWRP
g) wipe, then flash your ROM using adb sideload or normal flashing if you already have the rom in your device earlier. Then wipe again.
Tips:-
1. Make sure the driver is Android ADB Composite Driver is properly install or the unlock bootloader (unlock.bat) won't work
2. Installing Rom, press UP+POWER to go into TWRP, download the ROM to PC, then enable ADB side in TWRP, follow up with ADB sideload command in PC. Wipe before and after. :-
https://forum.xda-developers.com/kindle-fire-hdx/orig-development/rom-fire-nexus-rom-ktu84q-t3322931
3. Safe Strap is not supported in 4.5.5.2
4. Copy ROM zip file to /sdcard/ before doing the above to skip the adb sideload step and you can directly flash the rom from TWRP only.
5. Can't boot into 4.5.5.2 after unlock bootloader. I've tried issuing "fastboot -i 0x1949 oem idme bootmode 4000" and then "fastboot -i 0x1949 reboot" command but it does not work.
Added another instructions from another forumer who think my instructions is not complete:-
1. Install the moto driver and then plug in your device while running normal
2. Run the get_code.bat (from this link)
3. once unlock.code file is created, run "adb reboot bootloader". It will show [Fastboot] with the kf logo.
4. Once bootloader comes up, change driver in device manager for "Other Android" to use the Android -> Mot Adb Composite Driver. It should say "Ready" on the KF
5. Run the stuff from this post (do the bottom steps with fastboot erase first)
6. After you are done in bulk mode, hold the power button for 15 secs to reboot. It will automatically boot into Fastboot
7. When you run the unlock command, use the "unlock.code" file.. not the "0xmmssssssss.unlock" example from that link.
8. Now unplug and hold power again to shut down. Hold VolUp + Power. About 3 secs after you see the KF logo, you can let go of the power button (possibly both buttons) and you get TWRP
From here you can flash CM and gapps (5.1).
Click to expand...
Click to collapse
just wondering is it important to be on os 4.5.5.2 before rooting and unlocking boodloader? I am on OS 13.3.2.1 and I just have no idea what path to do. All I want is to not have OTA and have google play store working
BatmanDC said:
just wondering is it important to be on os 4.5.5.2 before rooting and unlocking boodloader? I am on OS 13.3.2.1 and I just have no idea what path to do. All I want is to not have OTA and have google play store working
Click to expand...
Click to collapse
You do not need to be on 4.5.5.2 or any specific version of FireOS for that matter. Is the device rooted?
BatmanDC said:
just wondering is it important to be on os 4.5.5.2 before rooting and unlocking boodloader? I am on OS 13.3.2.1 and I just have no idea what path to do. All I want is to not have OTA and have google play store working
Click to expand...
Click to collapse
As Davey said, no. The reason I created this thread because 4.5.5.2 is the last OTA. My point is even last OTA can root and unlock bootloader.
kkcheong said:
As Davey said, no. The reason I created this thread because 4.5.5.2 is the last OTA. My point is even last OTA can root and unlock bootloader.
Click to expand...
Click to collapse
I'd like to add that you don't even need root to unlock.
Personally, I'd stay away from Kingroot, unless that was the only option.
Thankfully, it is not.
draxie said:
I'd like to add that you don't even need root to unlock.
Personally, I'd stay away from Kingroot, unless that was the only option.
Thankfully, it is not.
Click to expand...
Click to collapse
are those instructions as daunting as they sound?
it seems if you kingroot and wipe everything it negates any malware?
barrist said:
...it seems if you kingroot and wipe everything it negates any malware?
Click to expand...
Click to collapse
Correct. KingRoot is a borderline malware but does not appear to harvest personal info during the rooting process and is completely irradiated by a wipe of the system and data partitions.
draxie said:
I'd like to add that you don't even need root to unlock.
Personally, I'd stay away from Kingroot, unless that was the only option.
Thankfully, it is not.
Click to expand...
Click to collapse
Davey126 said:
Correct. KingRoot is a borderline malware but does not appear to harvest personal info during the rooting process and is completely irradiated by a wipe of the system and data partitions.
Click to expand...
Click to collapse
Thanks
just picked up a used HDX off Kijiji, so i'm looking forward to tinkering.. can you suggest an initial stable rom to try? the KK based Nexus seems to be the safer one i'm gathering?
barrist said:
Thanks
just picked up a used HDX off Kijiji, so i'm looking forward to tinkering.. can you suggest an initial stable rom to try? the KK based Nexus seems to be the safer one i'm gathering?
Click to expand...
Click to collapse
There are no bad/unstable HDX ROMs. Fire Nexus has the advantage for those needed full Bluetooth and/or LTE support. Otherwise LineageOS 14.1 is a solid choice. Regardless of direction you'll want to unlock the bootloader and wipe the device immediately after rooting if KingRoot is utilized. Also know Amazon devices have their own set of quirks and don't behave like a typical Android gizmo.
Thanks maybe I'll give lineage a shot as I don't really don't need LTE or bt .. just hoping for stable app support and wifi
draxie said:
I'd like to add that you don't even need root to unlock.
Personally, I'd stay away from Kingroot, unless that was the only option.
Thankfully, it is not.
Click to expand...
Click to collapse
Thanks for the awesome info. But noob like me would prefer Kingroot because it give the illusion of zero risk :laugh:
nice, instructions worked, running lineage 14.1 and no problems so far!
kkcheong said:
Thanks for the awesome info. But noob like me would prefer Kingroot because it give the illusion of zero risk :laugh:
Click to expand...
Click to collapse
No problem.
Given that you wipe 'data' (which I prefer not to, because I'm too lazy to make backups),
you should be fine with KingRoot, it just takes much longer, but that's your choice.
The real risk is making a mistake when flashing aboot and TWRP, which is the same on both paths.
kkcheong said:
Finally I got myself to root and unlock bootloader of my Thor Kindles. I've been lurking for few years. Here is the steps:-
1. Install Kingroot from Kingroot website (https://kingroot.net/) and root the phone. I got it first try. But some people are saying they need 8 tries to work.
2. Flash TWRP and Unlock bootloaders. Instruction in https://forum.xda-developers.com/ki...r-firmware-t3463982/post70881555#post70881555. Instruction in this post is better than the first post (OP) in this thread. The step is:-
a) install ADB driver and install Kindle Fire USB driver
b) put get_code.bat and unlock.bat in adb.exe directory. Put aboot and cubed twrp in /sdcard/
b) create unlock.code with get_code.bat
c) flash aboot and cubed twrp with this command in DOS command prompt in adb.exe directory:-
d) make sure check the Android ADB Composite driver is properly install in Device Manager
e) execute unlock.bat
f) reboot, press UP + power to boot into TWRP
g) wipe, then flash your ROM using adb sideload or normal flashing if you already have the rom in your device earlier. Then wipe again.
Tips:-
1. Make sure the driver is Android ADB Composite Driver is properly install or the unlock bootloader (unlock.bat) won't work
2. Installing Rom, press UP+POWER to go into TWRP, download the ROM to PC, then enable ADB side in TWRP, follow up with ADB sideload command in PC. Wipe before and after. :-
https://forum.xda-developers.com/kindle-fire-hdx/orig-development/rom-fire-nexus-rom-ktu84q-t3322931
3. Safe Strap is not supported in 4.5.5.2
4. Copy ROM zip file to /sdcard/ before doing the above to skip the adb sideload step and you can directly flash the rom from TWRP only.
5. Can't boot into 4.5.5.2 after unlock bootloader. I've tried issuing "fastboot -i 0x1949 oem idme bootmode 4000" and then "fastboot -i 0x1949 reboot" command but it does not work.
Click to expand...
Click to collapse
I tried to follow all steps but cannot go beyond Step 2c. When I try to flash cubed and aboot, i get "cannot access file : file or directory not present" error. How should I proceed?
xyluss0 said:
I tried to follow all steps but cannot go beyond Step 2c. When I try to flash cubed and aboot, i get "cannot access file : file or directory not present" error. How should I proceed?
Click to expand...
Click to collapse
Have you put both file in the adb directory?
Yes I did. Also, I tried to go ahead on the next step and run unlock.bat but I got the error "incorrect unlock code".
xyluss0 said:
Yes I did. Also, I tried to go ahead on the next step and run unlock.bat but I got the error "incorrect unlock code".
Click to expand...
Click to collapse
Please print screen. Did you cd to ADB directory?
Root hdx 7 (3rd Gen.), FireOS 4.5.5.2 with towelroot
Hi,
I am wondering if the towelroot rooting process is working with the 4.5.5.2 version of the fireOS.
Do you recommend the usage of APK-versions of Kingroot or Towelroot over the use of Windowsversion esp. for Kingroot.
Do i need working internet connection during rooting process with APKs ?
Thx in advance
Achimbub
Root fails
kkcheong said:
Finally I got myself to root and unlock bootloader of my Thor Kindles. I've been lurking for few years. Here is the steps:-
1. Install Kingroot from Kingroot website (https://kingroot.net/) and root the phone. I got it first try. But some people are saying they need 8 tries to work.
2. Flash TWRP and Unlock bootloaders. Instruction in https://forum.xda-developers.com/ki...r-firmware-t3463982/post70881555#post70881555. Instruction in this post is better than the first post (OP) in this thread. The step is:-
a) install ADB driver and install Kindle Fire USB driver
b) put get_code.bat and unlock.bat in adb.exe directory. Put aboot and cubed twrp in /sdcard/
b) create unlock.code with get_code.bat
c) flash aboot and cubed twrp with this command in DOS command prompt in adb.exe directory:-
d) make sure check the Android ADB Composite driver is properly install in Device Manager
e) execute unlock.bat
f) reboot, press UP + power to boot into TWRP
g) wipe, then flash your ROM using adb sideload or normal flashing if you already have the rom in your device earlier. Then wipe again.
Tips:-
1. Make sure the driver is Android ADB Composite Driver is properly install or the unlock bootloader (unlock.bat) won't work
2. Installing Rom, press UP+POWER to go into TWRP, download the ROM to PC, then enable ADB side in TWRP, follow up with ADB sideload command in PC. Wipe before and after. :-
https://forum.xda-developers.com/kindle-fire-hdx/orig-development/rom-fire-nexus-rom-ktu84q-t3322931
3. Safe Strap is not supported in 4.5.5.2
4. Copy ROM zip file to /sdcard/ before doing the above to skip the adb sideload step and you can directly flash the rom from TWRP only.
5. Can't boot into 4.5.5.2 after unlock bootloader. I've tried issuing "fastboot -i 0x1949 oem idme bootmode 4000" and then "fastboot -i 0x1949 reboot" command but it does not work.
Click to expand...
Click to collapse
I am on Fire OS 4.5.5.2 (HDX 8.9 Apollo) and Kingroot can not root(both apk and windows versions). I tried both ten times. What can I do to root this device now?
achimbub said:
Hi,
I am wondering if the towelroot rooting process is working with the 4.5.5.2 version of the fireOS.
Do you recommend the usage of APK-versions of Kingroot or Towelroot over the use of Windowsversion esp. for Kingroot.
Do i need working internet connection during rooting process with APKs ?
Thx in advance
Achimbub
Click to expand...
Click to collapse
- TowelRoot is ineffective on FireOS v4
- recommend desktop version of KingRoot for 4.5.5.2 (still may not work)
- device does not need an active internet connection with desktop version
---------- Post added at 04:58 AM ---------- Previous post was at 04:55 AM ----------
bobcat131 said:
I am on Fire OS 4.5.5.2 (HDX 8.9 Apollo) and Kingroot can not root(both apk and windows versions). I tried both ten times. What can I do to root this device now?
Click to expand...
Click to collapse
KingOroot is the only other tool that reportedly works on 4.5.5.2. It also has a reputation for screwing up devices. Risky choice.
I don't have experience with the hardmod option, I can't downgrade the firmware because they removed Apply Update From ADB and the mtk-su method doesn't work.
I'm on Fire OS 5.6.8.0 and nothing's worked. How would I downgrade if there's no apply update via adb or is there a root method that works without hardmodding?
SamDungUser said:
I don't have experience with the hardmod option, I can't downgrade the firmware because they removed Apply Update From ADB and the mtk-su method doesn't work.
I'm on Fire OS 5.6.8.0 and nothing's worked. How would I downgrade if there's no apply update via adb or is there a root method that works without hardmodding?
Click to expand...
Click to collapse
Sorry, is not a Fire HD 8 (2016), is just a Fire HD 8 (2017)
AmznUser444 Dev said:
There's no way to do that. You have only to repurpose your Fire tablet:
Digital clock.
Digital picture frame.
Virtual MIDI keyboard.
Home automation panel.
VirtualTablet, a virtual drawing tablet.
Click to expand...
Click to collapse
Sorry I was being an idiot while posting that, I did find a solution to root and install TWRP. If anyone needs step by step instructions i'll reply to you with instructions.
SamDungUser said:
Sorry I was being an idiot while posting that, I did find a solution to root and install TWRP. If anyone needs step by step instructions i'll reply to you with instructions.
Click to expand...
Click to collapse
Instructions please!!
Pabla98 said:
Instructions please!!
Click to expand...
Click to collapse
Thank you for asking for instructions. I'm happy to help.
You will need to download these files
https://forum.xda-developers.com/attachment.php?attachmentid=4845269&stc=1&d=1571151710
https://forum.xda-developers.com/attachments/brick-douglas-zip.4825253/
You'll also need to be running Linux (not terminal emulators)
In most cases use Lubutnu 18.04
If you want to install roms it'll be in Fire HD 8 and HD 10 development with 26 threads (not the 30+ thread)
First: Download and put your files on the desktop and extract brick-douglas.
Open the folder
Go to Tools and open a terminal here.
Enter these commands first:
sudo apt update
sudo add-apt-repository universe
sudo apt install python3 python3-serial adb fastboot dos2unix
sudo systemctl stop ModemManager
sudo systemctl disable ModemManager
Once finished reboot your device to recovery:
Erase data by selecting Wipe Data/Wipe Cache.
Await for it to complete.
Now go to reboot to bootloader and select it.
Now it shall begin.
Execute this command: sudo brick-9820.sh
Wait for it to finish and you should see:
Writing Brick on your tablet
Force it off by Pressing and holding Power + Volume UP and wait for the screen to turn black.
Disconnect the device.
Exit all windows including terminal
Now extract amonet-douglas-v1.2.zip.
Now open amonet again
Now go to Tools > Open Terminal
Now it is time to unlock the bootloader.
Type in: sudo bootrom-step.sh
Press enter
Let it flash, NOTE this will take a while! PLEASE LET IT COMPLETE OR YOU WILL BRICK YOUR DEVICE.
DO NOT LET YOUR DEVICE BOOT INTO FireOS when the process is done.
Next type in: sudo fastboot-step.sh
It will now boot into a hacked fastboot mode and begin the payload to install TWRP. Let this finish or your device maybe bricked.
Once done it will reboot into TWRP and the process is finished!
You have now exploited your device! Now you can flash Magisk to root your device!
AmznUser444 Dev said:
Sorry, is not a Fire HD 8 (2016), is just a Fire HD 8 (2017)
Click to expand...
Click to collapse
Please don't try it with the 2016 (6th gen).
SamDungUser said:
Thank you for asking for instructions. I'm happy to help.
You will need to download these files
https://forum.xda-developers.com/attachment.php?attachmentid=4845269&stc=1&d=1571151710
https://forum.xda-developers.com/attachments/brick-douglas-zip.4825253/
You'll also need to be running Linux (not terminal emulators)
In most cases use Lubutnu 18.04
If you want to install roms it'll be in Fire HD 8 and HD 10 development with 26 threads (not the 30+ thread)
First: Download and put your files on the desktop and extract brick-douglas.
Open the folder
Go to Tools and open a terminal here.
Enter these commands first:
sudo apt update
sudo add-apt-repository universe
sudo apt install python3 python3-serial adb fastboot dos2unix
sudo systemctl stop ModemManager
sudo systemctl disable ModemManager
Once finished reboot your device to recovery:
Erase data by selecting Wipe Data/Wipe Cache.
Await for it to complete.
Now go to reboot to bootloader and select it.
Now it shall begin.
Execute this command: sudo brick-9820.sh
Wait for it to finish and you should see:
Writing Brick on your tablet
Force it off by Pressing and holding Power + Volume UP and wait for the screen to turn black.
Disconnect the device.
Exit all windows including terminal
Now extract amonet-douglas-v1.2.zip.
Now open amonet again
Now go to Tools > Open Terminal
Now it is time to unlock the bootloader.
Type in: sudo bootrom-step.sh
Press enter
Let it flash, NOTE this will take a while! PLEASE LET IT COMPLETE OR YOU WILL BRICK YOUR DEVICE.
DO NOT LET YOUR DEVICE BOOT INTO FireOS when the process is done.
Next type in: sudo fastboot-step.sh
It will now boot into a hacked fastboot mode and begin the payload to install TWRP. Let this finish or your device maybe bricked.
Once done it will reboot into TWRP and the process is finished!
You have now exploited your device! Now you can flash Magisk to root your device!
Click to expand...
Click to collapse
I need help I'm stuck at "USB Transfering..." on my device and "Sending 'brick'" on my Virtual Machine.
IsolatePlz said:
I need help I'm stuck at "USB Transfering..." on my device and "Sending 'brick'" on my Virtual Machine.
Click to expand...
Click to collapse
I found that issue too. Use brick.sh
SamDungUser said:
I found that issue too. Use brick.sh
Click to expand...
Click to collapse
I tried both I had to boot into Ubuntu off of a USB stick to root it.
IsolatePlz said:
I tried both I had to boot into Ubuntu off of a USB stick to root it.
Click to expand...
Click to collapse
Yeah. I experienced problems using virtual machines myself.
you need to brick your device , by short after thes back to stock recovery now can now downgrade
789mod said:
you need to brick your device , by short after thes back to stock recovery now can now downgrade
Click to expand...
Click to collapse
Yes, that's the hardware method that has a higher chance of working.
@SamDungUser are there any chances this trick works on Fire 7 with recent OS? Thanks
neFAST said:
@SamDungUser are there any chances this trick works on Fire 7 with recent OS? Thanks
Click to expand...
Click to collapse
Is your device the KFDOWI Douglas HD 8 2017?
My bad, I did not notice this is the HD 8 subsection. My device is a Fire 7 2019
WIll this work with the Kidle Fire 8 HD (10th Generation)? Happy to try if I can get confirmation this will work with that model...
reubendevries said:
WIll this work with the Kidle Fire 8 HD (10th Generation)? Happy to try if I can get confirmation this will work with that model...
Click to expand...
Click to collapse
NO
SamDungUser said:
Is your device the KFDOWI Douglas HD 8 2017?
Click to expand...
Click to collapse
yeaahh >>> root it from twrp just brick it
789mod said:
yeaahh >>> root it from twrp just brick it
Click to expand...
Click to collapse
Alreday rooted. I joined the Lineage os 15 beta for the HD 8 2017
I was able to root my HD 10 7th gen Suez by using these instructions https://forum.xda-developers.com/t/hd-10-2017-offline-rooting.3734860/
Now that I have a rooted device, I can't seem to figure out how to get rid of Amazon and flash a custom rom
Hello, quick question: How do I revert back to stock FIreOS from lineage 16. I read that it is just a matter of going to TWRP, wipe ccaches, install FireOS bin (renamed as .zip)...however my question is since I am on Lineage 16 with android version 9, which FireOS version I should install to go back to stock and avoid bootloops?
FireOS 6, I think is android version 8 and FireOS 7 is android version 9. Can I install any of them directly? Or it has to be one specific? Or do I need to downgrade?
Thank you in advance,
adtamez said:
Hello, quick question: How do I revert back to stock FIreOS from lineage 16. I read that it is just a matter of going to TWRP, wipe ccaches, install FireOS bin (renamed as .zip)...
Click to expand...
Click to collapse
You may want to wipe data too...
adtamez said:
however my question is since I am on Lineage 16 with android version 9, which FireOS version I should install to go back to stock and avoid bootloops?
FireOS 6, I think is android version 8 and FireOS 7 is android version 9. Can I install any of them directly? Or it has to be one specific? Or do I need to downgrade?
Click to expand...
Click to collapse
Installing a stock rom based on FireOS 6 will work and remain unlocked...
but the fireOS7 stock rom will bootloop on an unlocked device.
Sus_i said:
You may want to wipe data too...
Installing a stock rom based on FireOS 6 will work and remain unlocked...
but the fireOS7 stock rom will bootloop on an unlocked device.
Click to expand...
Click to collapse
Thank you.
I want to send it back to Amazon as part of a trade in for a newer tablet. How do I lock it (I'm assuming you are taking about the bootloader?) If you don't mind telling me a short summary of the steps to revert back to stock I appreciate it. Just to make sure that I am following the steps correctly and I am not missing anything.
Regards,
adtamez said:
How do I lock it (I'm assuming you are taking about the bootloader?) If you don't mind telling me a short summary of the steps to revert back to stock I appreciate it. Just to make sure that I am following the steps correctly and I am not missing anything.
Click to expand...
Click to collapse
You may follow the go-to-stock section from the unlock guide:
[UNLOCK][ROOT][TWRP][UNBRICK] Fire HD 8 2018 (karnak) amonet-3
Read this whole guide before starting. This is for the 8th gen Fire HD8 (karnak). Current version: amonet-karnak-v3.0.1.zip This is based on xyz`s original work, but adds some features such as reboot to hacked BL. It also intends to simplify...
forum.xda-developers.com
Code:
Going back to stock
Extract the attached zip-file "amonet-karnak-return-to-stock.zip"
into the same folder where you extracted "amonet-karnak-v3.0.1.zip"
and open a terminal in that directory.
Then run:
sudo ./return-to-stock.sh
Your device should reboot into Amazon Recovery.
Use adb sideload to install stock image from there.
(Make sure to use FireOS 6.3.0.0 or newer, otherwise you may brick your device)
Sus_i said:
You may follow the go-to-stock section from the unlock guide:
[UNLOCK][ROOT][TWRP][UNBRICK] Fire HD 8 2018 (karnak) amonet-3
Read this whole guide before starting. This is for the 8th gen Fire HD8 (karnak). Current version: amonet-karnak-v3.0.1.zip This is based on xyz`s original work, but adds some features such as reboot to hacked BL. It also intends to simplify...
forum.xda-developers.com
Code:
Going back to stock
Extract the attached zip-file "amonet-karnak-return-to-stock.zip"
into the same folder where you extracted "amonet-karnak-v3.0.1.zip"
and open a terminal in that directory.
Then run:
sudo ./return-to-stock.sh
Your device should reboot into Amazon Recovery.
Use adb sideload to install stock image from there.
(Make sure to use FireOS 6.3.0.0 or newer, otherwise you may brick your device)
Click to expand...
Click to collapse
thank you...so in order to do so, I need to use a Linux system, correct? I vaguely remember using this instruction to unlock it and had to use a usb stick with ubuntu. To go back to stock I need it again, correct?
Sus_i said:
You may follow the go-to-stock section from the unlock guide:
[UNLOCK][ROOT][TWRP][UNBRICK] Fire HD 8 2018 (karnak) amonet-3
Read this whole guide before starting. This is for the 8th gen Fire HD8 (karnak). Current version: amonet-karnak-v3.0.1.zip This is based on xyz`s original work, but adds some features such as reboot to hacked BL. It also intends to simplify...
forum.xda-developers.com
Code:
Going back to stock
Extract the attached zip-file "amonet-karnak-return-to-stock.zip"
into the same folder where you extracted "amonet-karnak-v3.0.1.zip"
and open a terminal in that directory.
Then run:
sudo ./return-to-stock.sh
Your device should reboot into Amazon Recovery.
Use adb sideload to install stock image from there.
(Make sure to use FireOS 6.3.0.0 or newer, otherwise you may brick your device)
Click to expand...
Click to collapse
Hi, so I'm trying to back to stock per the instructions but I have a problem. First I cannot run sudo ./return to stock because it shows on the computer terminal "waiting for device" but once I get into bootloader on the tablet the script runs. So I'm assuming it is made for the bootloader and it is just missing from the instructions.
But the problem is that the script runs, it tries to install boot.bin but it fails, the error states: "FAILED (remote: 'Flashing is not allowed in Lock State')". So I'm assuming I have the bootloader locked but how is that possible? Every instruction to be and to install lineage unlocks the bootloader and install TWRP. Which I have both. I have lineage and TWRP as recovery.
What do I do? Is it possible that I locked the bootloader after installing lineage? Is that even possible? I just don't remember what I did.
Any suggestions are very much welcomed.
Thanks
adtamez said:
Any suggestions are very much welcomed.
Click to expand...
Click to collapse
You can use the boot-fastboot script to get into the hacked fastboot (instead of the locked one), then you can run the script... or extract and flash the images out of the back2stock file by hand via fastboot flash...
Sus_i said:
You can use the boot-fastboot script to get into the hacked fastboot (instead of the locked one), then you can run the script... or extract and flash the images out of the back2stock file by hand via fastboot flash...
Click to expand...
Click to collapse
Thank you Sus, I figured that out as well. Unfortunately I keep getting problems as i move along on the process. So right now, I have the tablet turn on and connected to a live Ubuntu system. ADB recognizes de device and everything works, also adb reboot bootloader works. But in order to get to the hacked fastboot when I run the script: sudo ./boot-fastboot.sh this errors present and the tablet doesn't do anything:
[email protected]:/cdrom/amonet/amonet$ sudo ./boot-fastboot.sh
[2022-07-20 16:43:44.336269] Waiting for preloader
Traceback (most recent call last):
File "handshake2.py", line 17, in <module>
dev.find_device(True)
File "/cdrom/amonet/amonet/modules/common.py", line 63, in find_device
log("Waiting for preloader")
File "/cdrom/amonet/amonet/modules/logger.py", line 7, in log
with open("amonet.log", "a") as fout:
OSError: [Errno 30] Read-only file system: 'amonet.log'
What can I do? this is beyond my expertise. Is it saying that the preloader it is not found? What preloader is talking about and what can I do about this errors?
Thank you so much. Hopefully this thread will help other as well.
adtamez said:
Thank you Sus, I figured that out as well. Unfortunately I keep getting problems as i move along on the process. So right now, I have the tablet turn on and connected to a live Ubuntu system. ADB recognizes de device and everything works, also adb reboot bootloader works. But in order to get to the hacked fastboot when I run the script: sudo ./boot-fastboot.sh this errors present and the tablet doesn't do anything:
[email protected]:/cdrom/amonet/amonet$ sudo ./boot-fastboot.sh
[2022-07-20 16:43:44.336269] Waiting for preloader
Traceback (most recent call last):
File "handshake2.py", line 17, in <module>
dev.find_device(True)
File "/cdrom/amonet/amonet/modules/common.py", line 63, in find_device
log("Waiting for preloader")
File "/cdrom/amonet/amonet/modules/logger.py", line 7, in log
with open("amonet.log", "a") as fout:
OSError: [Errno 30] Read-only file system: 'amonet.log'
What can I do? this is beyond my expertise. Is it saying that the preloader it is not found? What preloader is talking about and what can I do about this errors?
Thank you so much. Hopefully this thread will help other as well.
Click to expand...
Click to collapse
Preloader is the first boot stage after the SOCs bootrom, you can see the current stage via lsusb command.
Make sure that you extract the amonet zip file on the ubuntu desktop (avoid any fat/exfat/ntfs devices), or download it again via ubuntu and extract it there... otherwise all permissions are gone and the script fails...