I have Samsung Galaxy A20 phone, stock firmware started lagging terribly after upgrading to One UI 3.1, so I decided to install Lineage OS (I've tried some custom roms like Sakura Project previously so I'm familiar with the process) and Gapps Pico (Arm64) for Android 11 which I have on my phone. I already had TWRP installed, with its help I performed data formatting and formatting of the Dalvik Cache, Cache, Data, Internal Storage and System partitions, after which I installed an archive with Lineageos 18.1 and Gapps to install, the installation went without errors and I pressed the reboot button, after which my phone, after a message from Samsung that I lost my warranty (already a common message, had it since rooting my device) and pressing the Power button to continue booting, just either turns off, or does not show the image.
I tried to force restart the phone (if it is still on) by pressing both the Volume Down and Power buttons for ~20 seconds and the phone indeed rebooted, showed the same warning again and the image is black again. I can't get into recovery by pressing the power button and volume up, nothing happens (or the screen is just black, I'm unsure about it), just the usual pressing/holding of the power button does nothing. I'm not sure if there is an image or if the phone just refuses to turn on, I don't have a suitable cable to bring the image to the computer screen. When the screen is black and I plug in the power cable, there is no vibration, which usually indicates that charging has started, also the screen does not show a charging indication (a circle with a lightning and a percentage usually), but if I perform hard reboot (I believe that's what it's called when you hold Power + Volume Down buttons) it shows me white circle and just a lightning icon which usually indicates bad connection, I guess, so when the cable is plugged in I cannot reboot using Power and Volume Down at all for some reason, it just shows me bad power connection indicator. Also, I cannot perform hard reboot when the cable is plugged in, it shows me that circle with a lightning for a split second and that's it.
I can assume that it's an unofficial Lineageos rom specifically for the Galaxy A20, which I downloaded from Sourceforge. What can I do to check the operability and preferably fix this failure?
Lmao, solved it by doing some kungfu, with the cable unplugged did the Volume Down + Power thing and then plugged the cable in and as quick as human being can be I held Volume Up + Power to get into TWRP and from there I was able to reboot into download mode and flask stock firmware using Odin (v 3.14 in my case)
Related
I rooted with CF-auto method, phone worked fine. I downloaded CWM Rom Manager and downloaded CWM Recovery through the app. I decided to try and flash TRiforce 5.4 as my first ROM. Selected to back up everything and wipe clean with a full install. Towards the end There was a fatal error. It said it needed to be rebooted. I clicked reboot now. It said something about AROMA installer. Then rebooted. It showed the Galaxy s4 logo, then went black. I waited and waited and waited. And nothing happened. I tried pressing power and nothing would happen. I eventually pulled the battery out and reinserted. Upon pressing power, the same thing. It would show Galaxy s4 logo then go to black. I thought perhaps my battery died during install. Tried plugging in to A/C adapter and the battery logo pops up but the circle that usually continues to flow in a circle just freezes and does not flow. No light turns on to indicate charging. If I unplug the charger it is still frozen on the same charge screen. I popped my battery into a friends s4 and it charges fine, and is still at about 50% power. I've tried vol up+home+power, vol down+home+power and they both get the same results, just the galaxy s4 logo, then black screen. No booting whatsoever. Does this mean my phone is now bricked?:crying:
edit, vol down+ power has just gotten me into download mode! I guess I'll download a stock rom tomorrow and flash it via odin. Sucks because i don't have internet at my house. I'm at the library right now... 15 hours to dl stock rom lol...
ChrisHebert said:
I rooted with CF-auto method, phone worked fine. I downloaded CWM Rom Manager and downloaded CWM Recovery through the app. I decided to try and flash TRiforce 5.4 as my first ROM. Selected to back up everything and wipe clean with a full install. Towards the end There was a fatal error. It said it needed to be rebooted. I clicked reboot now. It said something about AROMA installer. Then rebooted. It showed the Galaxy s4 logo, then went black. I waited and waited and waited. And nothing happened. I tried pressing power and nothing would happen. I eventually pulled the battery out and reinserted. Upon pressing power, the same thing. It would show Galaxy s4 logo then go to black. I thought perhaps my battery died during install. Tried plugging in to A/C adapter and the battery logo pops up but the circle that usually continues to flow in a circle just freezes and does not flow. No light turns on to indicate charging. If I unplug the charger it is still frozen on the same charge screen. I popped my battery into a friends s4 and it charges fine, and is still at about 50% power. I've tried vol up+home+power, vol down+home+power and they both get the same results, just the galaxy s4 logo, then black screen. No booting whatsoever. Does this mean my phone is now bricked?:crying:
edit, vol down+ power has just gotten me into download mode! I guess I'll download a stock rom tomorrow and flash it via odin. Sucks because i don't have internet at my house. I'm at the library right now... 15 hours to dl stock rom lol...
Click to expand...
Click to collapse
What about volume up + power? if recovery boots you can try to flash in that otherwise you are stuck trying to use odin
ChrisHebert said:
I rooted with CF-auto method, phone worked fine. I downloaded CWM Rom Manager and downloaded CWM Recovery through the app. I decided to try and flash TRiforce 5.4 as my first ROM. Selected to back up everything and wipe clean with a full install. Towards the end There was a fatal error. It said it needed to be rebooted. I clicked reboot now. It said something about AROMA installer. Then rebooted. It showed the Galaxy s4 logo, then went black. I waited and waited and waited. And nothing happened. I tried pressing power and nothing would happen. I eventually pulled the battery out and reinserted. Upon pressing power, the same thing. It would show Galaxy s4 logo then go to black. I thought perhaps my battery died during install. Tried plugging in to A/C adapter and the battery logo pops up but the circle that usually continues to flow in a circle just freezes and does not flow. No light turns on to indicate charging. If I unplug the charger it is still frozen on the same charge screen. I popped my battery into a friends s4 and it charges fine, and is still at about 50% power. I've tried vol up+home+power, vol down+home+power and they both get the same results, just the galaxy s4 logo, then black screen. No booting whatsoever. Does this mean my phone is now bricked?:crying:
edit, vol down+ power has just gotten me into download mode! I guess I'll download a stock rom tomorrow and flash it via odin. Sucks because i don't have internet at my house. I'm at the library right now... 15 hours to dl stock rom lol...
Click to expand...
Click to collapse
Try going into recovery mode again by pressing get down the volume down and home button than finally the power button. The phone should vibrate and then as soon as the Samsung logo comes out let go of the buttons or else the phone will reboot again. Time it right so it goes into recovery
droidtom said:
Try going into recovery mode again by pressing get down the volume down and home button than finally the power button. The phone should vibrate and then as soon as the Samsung logo comes out let go of the buttons or else the phone will reboot again. Time it right so it goes into recovery
Click to expand...
Click to collapse
Have you fixed this issue, volume up +home+power is recovery mode, volume down+home+power is to download mode then u press up to complete
Rezzing old thread, I know. But I'm leaving this here in case anyone is poking around for clues to their s4 not powering on.
I have one that does not power on, as in bo combination of "press this and that..." is going to work (as if that isnt the first step in troubleshooting...I know not everyone does it right, but its really annoying when any post mentioning no power on/not responding to any key presses or charger plugin is full of "just try harder to boot it" posts..... Anyways...) The power pins register about half a volt, surging around from 100mV to ~3V . The battery does not charge and there us a constant slowly draining voltage on the power pins while unplugged and no battery.
The only clue Ive found so far us a youtube video of a no power on S4 having its power IC replaced which fixed it. Unfortunately I dont have the tools currently to try it, so at least mine, is still dead in the water.....
I tried flashing the bootloader from here.
Then it went crazy or something, and got stuck on the powered by android logo, however i was still able to boot into download mode the first time by holding power + volume down button
to simulate a battery pull then quickly holding the volume down + home + power again. Then I tried flashing TWRP immediately in an attempt to make it work because i have a flash drive to microUSB adapter that allows me to read flash drives from my phone ( so that I can flash the rom properly ). The last time I was in TWRP there was 0 things in my storage everything was wiped after I flashed TWRP the first time
Now im trying to go back into download mode but it just wont let me after the battery pull.
1.) After simulating the battery pull, I immediately let go when the screen is dark.
2.) I immediately attempt to go into download. It shows the powered by android for a second, then flickers then it's back to the powered by android again.
3.) I think my recovery and download is screwed. Or something is going on
=== EDIT ===
I managed to get into download mode and flash back my stock rom.
I think the phone must have read my Power & Volume Down & Home button as the battery pull because I let go of all buttons completely before doing it.
Steps to get out of bricked hell:
• Hold Power & Volume Down until the phone turns off
• Immediately without letting go of the Power & Volume Down button, press the home button as well.
• If the timing is not correct just retry.
I recently updated my Samsung Galaxy Tab A T280 to the latest firmware and I lost my root. So this afternoon I re-rooted it. Or I attempted to, anyway. Everything seemingly went fine, and I booted into TWRP just fine. I went to flash the ROM and I also selected wipe cache/davlik cache to be done as well, and tapped reboot. My device then turned off and when it started the reboot, it got stuck on the Samsung Galaxy Tab A logo screen and would not move or power off by holding the power button (I tried for a LONG time by using a rubber band to hold it down so I didn't have to, with no luck), and every other combination of buttons wouldn't do a thing, except for holding power + vol down, which made it turn off and back on, but it wouldn't finish rebooting and it just got stuck at the Samsung Galaxy Tab A logo again. So then I thought that maybe plugging it into a charger might not be a bad idea, and after holding down power + vol down again, it turned off and turned on and showed a battery with a charging symbol. I've had it plugged in for an hour and it does not show a charge or do anything except for go back to that boot logo if I unplug it from the charger and again hold down power and volume down separately.
I know it's not hard bricked because it is somewhat responsive so I think there's a chance to fix it, hopefully. I just want it to turn on and fully reboot into anything or in any way that will allow me to be able to fix the issue. My computer will not recognize the device so ADB is not an option right now unless I'm wrong.
Thanks a lot guys, I am so confused and could really use some advice.
What firmware did you install
Try to install original firmware via software "Samsung Smart Switch" on your PC with connected tablet.
I too recommend that you try installing the last firmware that you were on via Odin. Also, when you hit that screen lock issue after a firmware flash, where only the Samsung logo appears do this:
1. press and hold Home + volume up and volume down along with power button (that's all 4 buttons). Hold it there for at least 20 seconds and it should power off.
2. Once the device powers off keep holding the buttons but let go of the volume down button.
3. Once the tablet starts to power back up again release the power button and then in about 1 to 2 second release the rest of the buttons.
This should get you back into recovery. You should at least be able to restore any backup, that you should have already, on your external micro SD.
Good luck.. : )
"Chance Favors the Prepared"
the above post is 100% right. Reboot back into recovery and you'll be good to go. Also twrp has a option to reboot back to recovery so this doesn't happen, just a fyi for future knowledge. Best of luck..
You tried to flash a rom with twrp?
You need to flash stock firmware with odin.
My phone ('base' G7) had an unplanned swimming lesson yesterday (accidentally dropped into the bath, fished out within a couple of seconds of entry), and while the OS is still functional (evidenced by the alarm going off this morning!) and the hardware buttons still work (holding the power button for ~10s still forces a reboot - whereupon the OS successfully loading is marked by the alarm restarting) and I can do the volume down + power button reboot (which presumably takes it to the boot options menu, which obviously I can't see), but (a) how do I actually power the thing off (other than waiting for the battery to deplete) and (b) how can I enter recovery, so I can hook it up to my PC and backup all the data from it?
(Stock ROM, unlocked bootloader, TWRP recovery, Magisk root)
Hello dear xda community
I have a px6 device from the company "Wondefoo" installed in my Mazda (without any hard buttons). It worked so far so good, but ZLink (Apple Carplay) didn't work, so I tried to fix this. To do that, I rooted the device, uninstalled the "ZLink" app and reinstalled a newer version. Then I tried to reboot. And then my problems started:
The device doesn't boot anymore. It tries to start up, I can see the Android 10 boot logo ("multi-media on-vehicle Navigation System" screen), but after about one minute, this logo disappears and the screen remains black.
OK, easy fix --> Just go into recovery mode and reset the device. But here's the big problem: I can't get into recovery mode.
Here's what I tried:
1. Ignition off and on --> Screen still black
2. Press "Reset" button (my device only has this one physical button) --> Boot process started again, but same outcome
3. Unmount the device, plug the power out, wait an hour, plug it in again and try again --> Boot process started again, but same outcome
4. Tried to connect with adb over Wi-Fi to the device (used the last known IP address) --> Connection timeout, Wi-Fi probably not started yet
5. Press&Hold "Reset" button until lights beign to flash to get into recovery mode --> Lights never flash because the "Reset" button somehow breaks the power circuit and when I release it, the device gets power again and boot process starts again with same outcome
6. Press&Hold "Reset" button for a minute, then release it, then press it again quickly within 1sec --> Boot process started again, same outcome
7. Tab with 5 fingers on the boot logo --> Nothing happened
8. Attached keyboard and pressed "Alt" + "PrintScreen" + "I" all the time --> Nothing happens. Keyboard is with RGB LEDs, so I saw it was active when the boot logo was displayed... Then, the LEDs on my keyboard turned off which was telling me that there is no keyboard input possible anymore
9. I even tried this: https://forum.xda-developers.com/t/new-method-enter-recovery-no-physical-buttons.4013453/ --> I just have one similar cable, not two as described in this post... So I put everything together again and just tried again --> Boot process started again, same outcome
Well... Is there any option left? I'm thinking about buying a USB male-to-male cable and try again with adb, but everyone tells me that I need to get into recovery mode first which I really can't
* Is there any other way to get into recovery mode? Maybe with my keyboard?
* Does anyone have another idea what I could try? Maybe without recovery mode?
Thanks in advance and cheers
T
As you said:
1. Ignition off and on
2.Have ready the needle for reset and do that instantly as you see the boot logo.
Once device restarted, wait until will see the boot logo again and pull out the ignition key.
3. Put in an USB socket a pen drive with the right firmware
4. Put back the ignition key and let it in ON position, without starting the engine. The update process will start, have a bit of patience until will finish. The device will restart at the end of the update, and straight after the boot logo, shortly press the reset button.
With a bit of luck, will have a fresh firmware on your device.
Thanks for your quick answer.
I tried what you said several times, but unfortunately I always end up on the black screen, no matter what I try.
My usb stick flashes quickly during the boot process, but nothing happens with it.
I also tried with an USB male-to-male cable and connect via adb, but it won‘t connect...
t-to-the-a said:
5. Press&Hold "Reset" button until lights beign to flash to get into recovery mode --> Lights never flash because the "Reset" button somehow breaks the power circuit and when I release it, the device gets power again and boot process starts again with same outcome
Click to expand...
Click to collapse
Are you sure you are holding the reset button for long enough?
On my machine (Dasaita) you hold the reset and the machine turns off... but you have to keep holding it even after it has turned off. Could be upwards of 1.5 minutes. Once the lights flash (and finished flashing), release and press one more time within 3 seconds.
Thank you for this idea. I have tried 30 seconds, but no more until today...
Now I tried with 1min, 2mins, even 3mins, but nothing happens.. I think the power is immediately cut as soon as I press the reset button. So there is probably no way to fix this easily
I also contacted the seller, but they have a talent to not understand my question. I just get answers like "press the reset button 2 sec and then everything is fixed" or "plug in the USB drive with the new ROM and press update" - of course that doesn't help.
Well I guess I'm left with one last thing: Throw this device away and buy a new one. Not from Wondefoo anymore of course, and hopefully with a working reset button.
I have the same issue. What did you end up doing?
Where did you buy your unit from?