LineageOS installs ok but bootloops instantly - Nokia 6.1 Plus (X6) Questions & Answers

Nokia x6 ta-1099 CN.
This week any and all versions of LineageOS (official 17-19, incl. microG versions) started to bootloop instantly after the flashing. I.e the rom installs fine, recovery menu works, but when the lineageOS logo comes up, it only lasts for abt. 1 seconds before auto-rebooting the phone.
I used to be able to install and run LineageOS in the past no problem using LineageOS official method (adb sideload) as well as TWRP "wipe->flash" method. Also, non-lineageOS roms work fine (HavocOS, PixelPlusUI, ArrowOS, AOSP).
Any reason why it suddenly bootloops? Is there any rookie mistake I'm making here?

are you doing a Clean Wipe before install?
clean wipe - wipe all partitions excluding vendor.

ai.Sanaul said:
are you doing a Clean Wipe before install?
clean wipe - wipe all partitions excluding vendor.
Click to expand...
Click to collapse
Yes, though I was wiping everything including the vendor.

Totesnochill said:
Yes, though I was wiping everything including the vendor.
Click to expand...
Click to collapse
maybe your phone is not compatible with the version, please check...
Edit: and yes this rom is not compatible with your phone. check some unofficial builds for your phone of Linage OS.

ai.Sanaul said:
maybe your phone is not compatible with the version, please check...
Edit: and yes this rom is not compatible with your phone. check some unofficial builds for your phone of Linage OS.
Click to expand...
Click to collapse
LineageOS for MicroG is officially compatible though, and I clearly remember installing an unofficial build in the past

Totesnochill said:
LineageOS for MicroG is officially compatible though, and I clearly remember installing an unofficial build in the past
Click to expand...
Click to collapse
Linage Os is officially not available for Nokia X6 ta-1099, i checked on offficial site...

Totesnochill said:
Nokia x6 ta-1099 CN.
This week any and all versions of LineageOS (official 17-19, incl. microG versions) started to bootloop instantly after the flashing. I.e the rom installs fine, recovery menu works, but when the lineageOS logo comes up, it only lasts for abt. 1 seconds before auto-rebooting the phone.
I used to be able to install and run LineageOS in the past no problem using LineageOS official method (adb sideload) as well as TWRP "wipe->flash" method. Also, non-lineageOS roms work fine (HavocOS, PixelPlusUI, ArrowOS, AOSP).
Any reason why it suddenly bootloops? Is there any rookie mistake I'm making here?
Click to expand...
Click to collapse
Can you please link me the TWRP latest file ? I haven’t found it yet. And also, were you able to install LineageOS on your phone?

Related

Fingerprint with Lineage OS and Ressurection Remix nougat

Hi everyone,
I have a little problem with fingerprint with these 2 roms.
Normally I could add 5 fingers but I can only 3 max. If I try to configure the last 2, all my fingerprints dont work at all.
Moreover I can't delete fingeprints. When I try, they come back.
That is an issue which not occur with 6.0 custom roms.
Someone know how to fx it?
Thanks.
I'd suggest flashing the stock nougat 93-11 or 93-14 firmware (e.g. from the guides section) to resolve your fingerprint issues. Once that's done, future installs of lineage and RR should have fingerprint support for more than 3 fingers.
Thanks for replying.
I have xt1642. Is there a stock firmware Nougat for this device? I didnt find it
Nicozyp said:
Thanks for replying.
I have xt1642. Is there a stock firmware Nougat for this device? I didnt find it
Click to expand...
Click to collapse
I've got an XT1642 (UK - retGB, EMEA baseband) and updated to Nougat 93-11 using the stock files on here okay (now running Lineage with 4 FPs set).
The ROM I used to upgrade was the one linked here: https://forum.xda-developers.com/moto-g4-plus/how-to/guide-install-official-december-nougat-t3518262 This will bring you up to the official 93-11 update via installing from stock recovery - you need Marshmallow build 139-63/64 however.
However, you may like to try either of these guides as well: https://forum.xda-developers.com/moto-g4-plus/how-to/moto-g4-plus-xt1640-43-athene-npj25-93-t3549369
https://forum.xda-developers.com/moto-g4-plus/how-to/android-7-0-install-nougat-official-t3531612
As long as you can successfully install a Nougat stock ROM onto your device, the updates should mean your fingerprint sensor works properly in the custom ROMs. Bear in mind that updating to Nougat may wipe your data and cause you to lose TWRP/root until you re-install them.
Last question: can I wipe system and internal storage before installing ressurection?
Nicozyp said:
Last question: can I wipe system and internal storage before installing ressurection?
Click to expand...
Click to collapse
Once you've installed Nougat (and I recommend installing TWRP too), if you wish to install Resurrection Remix, only wipe system, data, Dalvik and cache. Don't wipe internal storage, since that's where your ROM zip is stored!
Silesh's initial post on the RR version for Moto G4s has more information on this https://forum.xda-developers.com/moto-g4-plus/development/rom-resurrection-remix-n-5-8-0-t3507275
Unable to flash stock recovery => "image not signed or corrupt"
Nicozyp said:
Unable to flash stock recovery => "image not signed or corrupt"
Click to expand...
Click to collapse
The image is flashed. Boot into recovery and you'll realize.
Nicozyp said:
Unable to flash stock recovery => "image not signed or corrupt"
Click to expand...
Click to collapse
Which file are you flashing? Does it end in OKAY after that error?
EDIT - zeomal is too quick for me
Indeed it's ok.
For the moment I upgrade MM, then gonna flash stock Nougat.
So problem solved.
I've flashed RR and configured fingerprint ==> it works fine
Thanks for ur help and advices
fingerprint option is not displayed in my zuk z1
Hey I have installed official lineage-os on my zuk z1 handset but still I can't find fingerprint option in my zuk
What to do help me

PSA - DotOS 8.1 for Huawei Hi6250 devices works flawlessly

I was about to give up and go back to stock but lo and behold I got ahold of a link to a really nice GSI for our Honor 7x devices, and any other device with the Hi6250 chipset. It has worked flawlessly on my BND-L24 and doesn't give me weird uncertified device and internal storage errors like the treble GSI found in the treble ROM forums.
Download link (2nd time just in case) - https://forum.xda-developers.com/p8lite/p8-lite-2017-development/rom-dotos-8-1-huawei-hi6250-t3793970
Open GApps (I use Pico) - https://opengapps.org
Treble GSIs (Why not) - https://github.com/phhusson/treble_experimentations/wiki/Generic-System-Image-(GSI)-list
Latest Magisk (Beta for fixed bugs and whatnot) - https://forum.xda-developers.com/apps/magisk/beta-magisk-v13-0-0980cb6-t3618589
Installation instructions -
crayonicle said:
I assume you have this TWRP installed, if not, install it: TWRP
Alright, let's install.
1. Boot into TWRP
2. Go to wipe - advanced wipe
3. Wipe all but SD card
3. Then go back to wipe.
4. There is an option next to advanced wipe, forgot what it was. (I think it was "Format Data")
5. Tap that option and type "yes"
6. Reboot back into TWRP
7. Flash the ROM and flash Open GApps right after flashing the ROM (I used Pico Open GApps)
8. Do a factory reset, wipe Cache, Dalvik / ART cache, and Data in advanced wipe just to be sure.
9. Reboot
Click to expand...
Click to collapse
EDIT: I'm no longer on this ROM so if there are bugs and you want me to reproduce them, I can not help you. Sorry, I need a more stable ROM for our Honor 7x's than this one. Thanks for understanding.
It's not the best idea to wipe with TWRP. It's better to do it with stock recovery or manually with fastboot.
Hi !
Does it work on BND-L21C432 ? What are the steps to install the rom ? Does it have to be EMUI 8.0 ?
Thank you for your work on this rom!
flashing this i hope the battery sot is good
Thanks for pointing this Rom out crayonicle, just flashed it and it's freaking great!!
jmoss1972 said:
Thanks for pointing this Rom out crayonicle, just flashed it and it's freaking great!!
Click to expand...
Click to collapse
Well until i flashed magisk and now all i get after flashing the rom is stock recovery
imHadees said:
It's not the best idea to wipe with TWRP. It's better to do it with stock recovery or manually with fastboot.
Click to expand...
Click to collapse
Yeah, you're right, I could end up messing up partitions and whatnot...
But I'm known for being careless ¯\_(ツ)_/¯
DaRkLinK_35 said:
Hi !
Does it work on BND-L21C432 ? What are the steps to install the rom ? Does it have to be EMUI 8.0 ?
Thank you for your work on this rom!
Click to expand...
Click to collapse
Yes, this ROM will run on your device!
Well, I didn't make this ROM at all, I'm just here to share it...
I already showed you the steps, read the original post!
You must be on EMUI 8 or you will brick your device!
jmoss1972 said:
Well until i flashed magisk and now all i get after flashing the rom is stock recovery
Click to expand...
Click to collapse
Did you flash the latest Magisk Beta?
Usually that is the one that works, or you can find a treble-compatible version of Magisk to flash.
crayonicle said:
Did you flash the latest Magisk Beta?
Usually that is the one that works, or you can find a treble-compatible version of Magisk to flash.
Click to expand...
Click to collapse
Yes I flashed the 16.4, not sure what happened. I can get into twrp, tried wiping and flashing the DotOs image again but all it does is boot into Huawei recovery. When I get home I will try downloading the stock firmware from the MT website and if I can get it to boot up Ill try flashing DotOs again.
jmoss1972 said:
Yes I flashed the 16.4, not sure what happened. I can get into twrp, tried wiping and flashing the DotOs image again but all it does is boot into Huawei recovery. When I get home I will try downloading the stock firmware from the MT website and if I can get it to boot up Ill try flashing DotOs again.
Click to expand...
Click to collapse
Hmmmm... I flashed Magisk fine here...
Hope you get it working again :good:
crayonicle said:
Hmmmm... I flashed Magisk fine here...
Hope you get it working again :good:
Click to expand...
Click to collapse
How's it compared to lineage 15.1? How's battery life? Post few screenshots and check whether substratum works or not? TIA
Tried flashing gapps linked and get an error about gapps isnt compatible. Tried flashing 8.0, 8.1 and 7.1.2 gapps and none work.
Hell yeah got the phone operational again, time to get back to flashing.
Username.php said:
How's it compared to lineage 15.1? How's battery life? Post few screenshots and check whether substratum works or not? TIA
Click to expand...
Click to collapse
More features than Lineage and the SOT seems to be higher
Substratum only works with Magisk or other root installed
Screenshots: Google Drive link
tlxxxsracer said:
Tried flashing gapps linked and get an error about gapps isnt compatible. Tried flashing 8.0, 8.1 and 7.1.2 gapps and none work.
Click to expand...
Click to collapse
Most likely there is something wrong with what you're using to flash the GApps, like the SD card, USB OTG, etc. Try switching it out.
But before doing all that, first flash the ROM, and then reboot again into TWRP and try flashing it if that makes a difference. Make sure you're flashing the ROM like the original post says.
crayonicle said:
Most likely there is something wrong with what you're using to flash the GApps, like the SD card, USB OTG, etc. Try switching it out.
But before doing all that, first flash the ROM, and then reboot again into TWRP and try flashing it if that makes a difference. Make sure you're flashing the ROM like the original post says.
Click to expand...
Click to collapse
Trust me, I am. ROM boots up fine though.
crayonicle said:
Hmmmm... I flashed Magisk fine here...
Hope you get it working again :good:
Click to expand...
Click to collapse
It was there all along, I'm a moron. It was in the settings menu.
crayonicle said:
I was about to give up and go back to stock but lo and behold I got ahold of a link to a really nice GSI for our Honor 7x devices, and any other device with the Hi6250 chipset. It has worked flawlessly on my BND-L24 and doesn't bootloop like the treble GSI found in the treble ROM forums.
Download link (2nd time just in case) - https://forum.xda-developers.com/p8lite/p8-lite-2017-development/rom-dotos-8-1-huawei-hi6250-t3793970
Open GApps (I use Pico) - https://opengapps.org
Treble GSIs (Why not) - https://github.com/phhusson/treble_experimentations/wiki/Generic-System-Image-(GSI)-list
Latest Magisk (Beta for fixed bugs and whatnot) - https://forum.xda-developers.com/apps/magisk/beta-magisk-v13-0-0980cb6-t3618589
Installation instructions -
Click to expand...
Click to collapse
That's great! Definitely giving this one a try
I recommend it, working great for me as well.
Is it just me or does the inbuilt UI tweaker not work? I can change the accents but not the settings and quicksettings background

Lineage OS 16 in Oneplus 5 - July 2019

Hi,
I bought a oneplus 5 phone because I was told it was going to be easy to install Lineage OS. I have try to install Lineage OS 16 on it for 2 days without success.
The first issue i had was installing twrp. Most of the twrp available did not worked with my phone. After flashing them with fastboot and reboot to recovery I would end up with a black screen and the the blue led turn on.
However I did find two TWPRs that work:
- twrp-3.2.1-1-cheeseburger.img
- twrp-3.2.3-0-20180822-codeworkx-cheeseburger.img
There might be other that would work, but this are the ones that I have tested.
After being able to boot to TWRP I try to flash the firmware 9.06 with success. Without reboot I flash lineage without success. I try to reboot and the system did not worked and I never reboot.
After a while I found a OxygenOS 4.5.10 that I hope is the stock rom. I has the following sha256sum: 7a8268f6a133f090a2d304aad2f92393aefbd4df34a6c2ed088909aaf7ccc2dd
That did worked and give me a breath. At least I had a working phone now. However I try to update and it did not worked.
From there I have been strugling with this project to install Lineage OS in my new phone. I know there are guides out there, but most of them did not work or are outated. There ara also threads in this forums, but are to big to try to follow. So I start this one, hopefully you can help me.
It would be great if there is a step by step guide on how to run Lineage OS in this phone.
Best,
Panoramix Druida
panoramix.druida said:
Hi,
I bought a oneplus 5 phone because I was told it was going to be easy to install Lineage OS. I have try to install Lineage OS 16 on it for 2 days without success.
The first issue i had was installing twrp. Most of the twrp available did not worked with my phone. After flashing them with fastboot and reboot to recovery I would end up with a black screen and the the blue led turn on.
However I did find two TWPRs that work:
- twrp-3.2.1-1-cheeseburger.img
- twrp-3.2.3-0-20180822-codeworkx-cheeseburger.img
There might be other that would work, but this are the ones that I have tested.
After being able to boot to TWRP I try to flash the firmware 9.06 with success. Without reboot I flash lineage without success. I try to reboot and the system did not worked and I never reboot.
After a while I found a OxygenOS 4.5.10 that I hope is the stock rom. I has the following sha256sum: 7a8268f6a133f090a2d304aad2f92393aefbd4df34a6c2ed088909aaf7ccc2dd
That did worked and give me a breath. At least I had a working phone now. However I try to update and it did not worked.
From there I have been strugling with this project to install Lineage OS in my new phone. I know there are guides out there, but most of them did not work or are outated. There ara also threads in this forums, but are to big to try to follow. So I start this one, hopefully you can help me.
It would be great if there is a step by step guide on how to run Lineage OS in this phone.
Best,
Panoramix Druida
Click to expand...
Click to collapse
Hello, seems that you did not follow the installation instructions within the official LineageOS thread https://forum.xda-developers.com/oneplus-5/development/rom-lineageos-16-0-pie-oneplus-5-t3843064
Your issues are clearly missed or skipped steps.
Please follow the instructions there and if you get stuck, report back with detailed information :good:
Thanks a lot for your quick response. It do have an issue with that guide and it is with point 1:crying::crying:
- Make sure your phone was running OxygenOS 5.1.4 at least once
Click to expand...
Click to collapse
I have OxygenOS 4.5.10 and it does not upgrade to OxygenOS 5.1.4. What happened, is that in my first attempts to get this thing working I brick the phone and loose the stock firmware. Then I found this rom that allow me to use the phone (OxygenOS 5.1.4)
OnePlus5Oxygen_23_OTA_015_all_1708252353_f05918.zip
sha256: 7a8268f6a133f090a2d304aad2f92393aefbd4df34a6c2ed088909aaf7ccc2dd
It make the phone usable, but not upgradable. I doubt is the original, but I found the link on the Oneplus forums. (I can not post links because I am too new here)
After that I search for a ROM that comes with 5.1.4 and was really happy, and try to flash. It did not work, it is like it tries to boot, but never finish booting. I wait at least for 10 minutes. This the file and the sha256 hash:
OnePlus5Oxygen_23_OTA_037_all_1807181258_7b4b6.zip
sha256 2bb2e21a43572ac4bd2e5d1d30a3fb7562ddec280df3d452d61f58a4a8135f14
So I guess my first step would to find a way to get Oneplus 5.1.4 working. When I first try to upgrade the phone, I upgrade it from OxygenOS and it worked, however then I mess things and brick the phone. I found the rom that allow the phone to work (4.5.10), but for some reason the upgrades do not.
Thank you very much for your time.
panoramix.druida said:
Thanks a lot for your quick response. It do have an issue with that guide and it is with point 1:crying::crying:
I have OxygenOS 4.5.10 and it does not upgrade to OxygenOS 5.1.4. What happened, is that in my first attempts to get this thing working I brick the phone and loose the stock firmware. Then I found this rom that allow me to use the phone (OxygenOS 5.1.4)
OnePlus5Oxygen_23_OTA_015_all_1708252353_f05918.zip
sha256: 7a8268f6a133f090a2d304aad2f92393aefbd4df34a6c2ed088909aaf7ccc2dd
It make the phone usable, but not upgradable. I doubt is the original, but I found the link on the Oneplus forums. (I can not post links because I am too new here)
After that I search for a ROM that comes with 5.1.4 and was really happy, and try to flash. It did not work, it is like it tries to boot, but never finish booting. I wait at least for 10 minutes. This the file and the sha256 hash:
OnePlus5Oxygen_23_OTA_037_all_1807181258_7b4b6.zip
sha256 2bb2e21a43572ac4bd2e5d1d30a3fb7562ddec280df3d452d61f58a4a8135f14
So I guess my first step would to find a way to get Oneplus 5.1.4 working. When I first try to upgrade the phone, I upgrade it from OxygenOS and it worked, however then I mess things and brick the phone. I found the rom that allow the phone to work (4.5.10), but for some reason the upgrades do not.
Thank you very much for your time.
Click to expand...
Click to collapse
You need to clean flash oxygenOS 5.1.4, then take ota update to 9.0.7 so you have the latest firmware.
Clean flash means that you need to wipe system, data, cache and format internal storage too.
So please backup everything off your device at first!
Everything you need you find here on xda, like the roms https://forum.xda-developers.com/oneplus-5/how-to/oneplus-5-mirrors-official-oxygen-os-t3628190
strongst said:
You need to clean flash oxygenOS 5.1.4, then take ota update to 9.0.7 so you have the latest firmware.
Clean flash means that you need to wipe system, data, cache and format internal storage too.
So please backup everything off your device at first!
Everything you need you find here on xda, like the roms https://forum.xda-developers.com/oneplus-5/how-to/oneplus-5-mirrors-official-oxygen-os-t3628190
Click to expand...
Click to collapse
Thanks, I would try this when I have time later today.
strongst said:
You need to clean flash oxygenOS 5.1.4, then take ota update to 9.0.7 so you have the latest firmware.
Clean flash means that you need to wipe system, data, cache and format internal storage too.
So please backup everything off your device at first!
Everything you need you find here on xda, like the roms https://forum.xda-developers.com/oneplus-5/how-to/oneplus-5-mirrors-official-oxygen-os-t3628190
Click to expand...
Click to collapse
Finally I had time to work on this. The rom for 5.1.4 is: OnePlus5Oxygen_23_OTA_037_all_1807181258_7b4b6.zip, that I already tried and never boots . With twrp it seems that the Rom is installed, with the stock recovery the installation never ends. I am going to try with other ROMS. Hopefully one of them would allow updates.
I am going to start with the newest 5.1.7, and if that does not work would keep going down.
Thanks again.
panoramix.druida said:
Finally I had time to work on this. The rom for 5.1.4 is: OnePlus5Oxygen_23_OTA_037_all_1807181258_7b4b6.zip, that I already tried and never boots . With twrp it seems that the Rom is installed, with the stock recovery the installation never ends. I am going to try with other ROMS. Hopefully one of them would allow updates.
I am going to start with the newest 5.1.7, and if that does not work would keep going down.
Thanks again.
Click to expand...
Click to collapse
5.1.7 did not boot, however I have some progress. I installed 4.5.12, I was previously at 4.5.10, so my android setup security patch levels went from July 2017 to to September 2017. Small step forward.
I have have that hypothesis that it would work with 4.x.x versions and not with 5.x.x versions. Tomorrow I would try to flash the latest 4.x.x and the earliest 5.x.x to see when does this things stop working.
I did the tests and I can flash up to 4.5.15. I tried to flash 5.0 and that did not worked. It flashes correctly, but it never finish booting, I waited up to 10 minutes.
So there is something preventing the phone to use version 5.x.x Should I try upgrading the firmware? Other ideas?
panoramix.druida said:
I did the tests and I can flash up to 4.5.15. I tried to flash 5.0 and that did not worked. It flashes correctly, but it never finish booting, I waited up to 10 minutes.
So there is something preventing the phone to use version 5.x.x Should I try upgrading the firmware? Other ideas?
Click to expand...
Click to collapse
Please give detailed steps what you did including file versions. Otherwise I cannot help further.
Every oxygenOS version has firmware built in, no need to update it seperately.
Follow this:
1 flash this recovery with fastboot like the first time https://drive.google.com/file/d/1UlTftbe6wooAs4Fp0cjwXlOKmfQHgdfL/view?usp=drivesdk
2 boot the new twrp recovery
3 flash magisk 18.1 to make twrp stick
4 FORMAT internal storage(not wipe only) and wipe system and data partition
5 transfer oxygenOS 5.1.4 to the phone and flash it
6 boot oxygenOS 5.1.4 and take ota update to tg and latest OxygenOS(9.0.7 actually.
7 now you're on the latest OxygenOS and firmware version
Thank you very much, now I am with LineageOS

[GUIDE] [TB-X606F] [Lenovo M10 Plus FHD] How to flash TWRP, Generic System Image (Android 11, Android 12), and Root with Magisk

Hi, I'm a long-time lurker on these forums but recently had some success flashing a GSI and rooting the Lenovo Tab M10 Plus (FHD) (X606F) with TWRP, and wanted to share my exact steps here. This device is awesome for the price point but unfortunately not popular enough to have many guides available. The tablet is Project Treble compatible and uses A/B roms (although it is not an A/B device in terms of OTA updates). You can use the Treble Info app to confirm that the devices uses an ARM64 A/B operating system. This was tested with the CAOS 11 GSI based on Android 11; it may work on other GSIs and other Android versions but I have not tested those (NOTE: user below confirms working on Android 12). I've written this guide at a bird's-eye-view meant for users familiar with flashing.
A couple useful notes before we begin:
- Hardware force off: hold down both volume buttons + power button
- Hardware boot into bootloader: while powered off, hold volume down + power button
- Hardware boot into recovery: hold down both volume buttons + power button
- While in fastboot mode, the command `fastboot reboot recovery` does not work for me on this device. You may have to hardware boot into recovery using the hardware steps above (power off completely then hardware boot). [This command may work for some people. It does not work for my device.]
Obviously, make sure your bootloader is unlocked before starting.
1. I used Ubuntu since Windows was having trouble recognizing the device in fastboot mode; linux drivers seem to be better developed for this particular device. I used `sudo apt install android-sdk` to get the drivers. Much easier than the nonsense that you have to do on Windows to get this device to work. Unfortunately, the Lenovo rescue app is available only for Windows, so you'll need access to Windows to gain access to vbmeta.img for installing TWRP (below).
2. Install TWRP following this guide: https://forum.xda-developers.com/t/...rp-3-5-x-for-lenovo-tab-m10-fhd-plus.4222887/. It is important that you follow all these steps. After flashing the recovery, you must reboot into recovery to ensure that TWRP permanently installs. If the `fastboot reboot recovery` command does not work for you, hold down the power button to power off the device, then hardware boot into TWRP by holding down both volume buttons + power button to boot into TWRP. If you do not perform this step, the device will boot normally and TWRP will be erased. After booting into TWRP, wipe -> format data.
3. In TWRP, flash CAOS 11 GSI: https://forum.xda-developers.com/t/official-aosp-r-mod-caos11.4265059/. You can try with other GSIs - it will probably work - but I've only tested this particular one, and can attest for the stability of CAOS 11 on this device. The image you'll want is named with -arm64-bgZ. If you use another GSI, make sure to use the A/B arm64 image. CAOS 11 has gapps included, so no need to flash here; if you use another GSI that does not have, you'll need to flash the appropriate gapps yourself. You can also opt for the non-gapps download if you don't want Google spying on you.
4. (Optional/No longer necessary) In TWRP, flash to disable dm-versity: https://zackptg5.com/android.php#disverfe.
5. (Optional - many GSIs come with root) In TWRP, flash standard Magisk.zip: https://github.com/topjohnwu/Magisk. I didn't need to use Magisk-Phh.
6. Reboot system.
7. You may or may not get errors from Google Play saying that the device is not certified. Follow these steps:
- Sign into Google account on device via settings
- Download and install the Get ID app: https://f-droid.org/en/packages/makeinfo.com.getid/
- Open the app and Copy Google Service Framework Key
- Go to https://www.google.com/android/uncertified/
- Sign in and paste the copied value to it, register
- Reboot (this actually took me a few tries to get working, I believe the key is to make sure you're signed into your Google account)
- Google Play should be working
Feel free to ask any questions here.
I got this working with the PHH android 12 pre-release version. So far everything seems to be working. There are a couple things I have to sort out still like it passes safetynet but some apps still don't show up in the play store.
dpn982 said:
I got this working with the PHH android 12 pre-release version. So far everything seems to be working. There are a couple things I have to sort out still like it passes safetynet but some apps still don't show up in the play store.
Click to expand...
Click to collapse
Good to know that Android 12 works. What apps aren't showing up for you? Maybe they are simply incompatible with Android 12.
shnioob said:
Good to know that Android 12 works. What apps aren't showing up for you? Maybe they are simply incompatible with Android 12.
Click to expand...
Click to collapse
Netflix is one, maybe Disney plus too. It could be that I just need to restart cause I haven't done that since I got safetynet passing. I was waiting for the bulk of the apps to restore first.
dpn982 said:
Netflix is one, maybe Disney plus too. It could be that I just need to restart cause I haven't done that since I got safetynet passing. I was waiting for the bulk of the apps to restore first.
Click to expand...
Click to collapse
I think this tablet has always had an issue with Netflix due to lack of DRM or something of that nature - I wasn't able to get Netflix on the stock version. Disney+ is probably the same issue.
If you have some free time, it would be great if you can outline your steps for getting safetynet to pass. I haven't bothered with it.
Nice thread. Here's some thoughts to help make this process simpler.
Following the numbering in the OP:
If you are using Windows, just make sure you have the latest OEM drivers from Mediatek (MTK).
after flashing TWRP and vbmeta, you can try fastboot reboot recovery to boot to twrp. I know the OP says it doesn't work, but it works on my TB-X606FA.
..and it's also a good idea to format data, especially if you're upgrading to a new OS level. This will delete everything on the data partition.
phhusson keeps a list of GSIs based on his work.
this step is now optional. TWRP (v3.6.0) has been patched to handle the A12 keymaster.
many GSIs come with root as standard. If yours does (or if you installed Magisk-Phh), then you can use the Magisk app as a root manager, but be aware that updating Magisk from inside the app might break the GSI.
-
some of the latest GSIs have fixed this issue and the integrated gapps should just work.
Yahoo Mike said:
Nice thread. Here's some thoughts to help make this process simpler.
Following the numbering in the OP:
If you are using Windows, just make sure you have the latest OEM drivers from Mediatek (MTK).
after flashing TWRP and vbmeta, you can try fastboot reboot recovery to boot to twrp. I know the OP says it doesn't work, but it works on my TB-X606FA.
..and it's also a good idea to format data, especially if you're upgrading to a new OS level. This will delete everything on the data partition.
phhusson keeps a list of GSIs based on his work.
this step is now optional. TWRP (v3.6.0) has been patched to handle the A12 keymaster.
many GSIs come with root as standard. If yours does (or if you installed Magisk-Phh), then you can use the Magisk app as a root manager, but be aware that updating Magisk from inside the app might break the GSI.
-
some of the latest GSIs have fixed this issue and the integrated gapps should just work.
Click to expand...
Click to collapse
Thanks!
By the way, about point number 7, which roms are like this? I have tried: Phhusson Android 12 latest version, PE 12 latest version and Lineage OS by AndyYan, all with gapps but I get the error
emilio666 said:
Thanks!
By the way, about point number 7, which roms are like this? I have tried: Phhusson Android 12 latest version, PE 12 latest version and Lineage OS by AndyYan, all with gapps but I get the error
Click to expand...
Click to collapse
NEVERMIND, it got solved by just waiting a couple of hours after using the Google website: https://www.google.com/android/uncertified/
Thanks a lot for this guide.
I just installed the latest Phh AOSP 12 GSI (system-squeak-arm64-ab-vndklite-gapps.img.xz) without problems by following your recommendations. I used the lastest twrp_X606FA_11. Flashing dm-verity or Magisk was not required for this GSI to work (it's already rooted). I did have to register my device to solve the "Google Uncertified" issue.
Yahoo Mike said:
Nice thread. Here's some thoughts to help make this process simpler.
Following the numbering in the OP:
If you are using Windows, just make sure you have the latest OEM drivers from Mediatek (MTK).
after flashing TWRP and vbmeta, you can try fastboot reboot recovery to boot to twrp. I know the OP says it doesn't work, but it works on my TB-X606FA.
..and it's also a good idea to format data, especially if you're upgrading to a new OS level. This will delete everything on the data partition.
phhusson keeps a list of GSIs based on his work.
this step is now optional. TWRP (v3.6.0) has been patched to handle the A12 keymaster.
many GSIs come with root as standard. If yours does (or if you installed Magisk-Phh), then you can use the Magisk app as a root manager, but be aware that updating Magisk from inside the app might break the GSI.
-
some of the latest GSIs have fixed this issue and the integrated gapps should just work.
Click to expand...
Click to collapse
Thanks for the clarifying info, updated the OP a bit. And thanks for providing us with a TWRP to make this possible. Otherwise this awesome tablet would be stuck on Android 10 forever.
vladilog said:
Thanks a lot for this guide.
I just installed the latest Phh AOSP 12 GSI (system-squeak-arm64-ab-vndklite-gapps.img.xz) without problems by following your recommendations. I used the lastest twrp_X606FA_11. Flashing dm-verity or Magisk was not required for this GSI to work (it's already rooted). I did have to register my device to solve the "Google Uncertified" issue.
Click to expand...
Click to collapse
Happy to help, glad it worked for you. I tried installing some other GSIs with and without flashing Magisk - LineageOS 12 boots but is very buggy, after reboot I was unable to get past the lockscreen. PixelExperience 11 and 12 cause a bootloop. If anyone has had success with PixelExperience I would love to get your input.
Yahoo Mike said:
Nice thread. Here's some thoughts to help make this process simpler.
Following the numbering in the OP:
If you are using Windows, just make sure you have the latest OEM drivers from Mediatek (MTK).
after flashing TWRP and vbmeta, you can try fastboot reboot recovery to boot to twrp. I know the OP says it doesn't work, but it works on my TB-X606FA.
..and it's also a good idea to format data, especially if you're upgrading to a new OS level. This will delete everything on the data partition.
phhusson keeps a list of GSIs based on his work.
this step is now optional. TWRP (v3.6.0) has been patched to handle the A12 keymaster.
many GSIs come with root as standard. If yours does (or if you installed Magisk-Phh), then you can use the Magisk app as a root manager, but be aware that updating Magisk from inside the app might break the GSI.
-
some of the latest GSIs have fixed this issue and the integrated gapps should just work.
Click to expand...
Click to collapse
So i can flash the official google GSI using these steps?
Branch Grid
ci.android.com
I don't need root and want to be stock as possible.
jebise101 said:
So i can flash the official google GSI using these steps?
Branch Grid
ci.android.com
I don't need root and want to be stock as possible.
Click to expand...
Click to collapse
Give it a try and let us know. I think some GSIs are more stable than others. I've had trouble with LOS and PE on this device.
shnioob said:
Give it a try and let us know. I think some GSIs are more stable than others. I've had trouble with LOS and PE on this device.
Click to expand...
Click to collapse
How do you go back to stock in case this does not work?
Is there a factory image?
jebise101 said:
How do you go back to stock in case this does not work?
Is there a factory image?
Click to expand...
Click to collapse
you can download the stock ROM from LMSA
I also have Lenovo tab m10 fhd plus but it is tb-x606v. Can I flash x606f rom on this device and flash twrp after.i don't want my device to be bricked.
vladilog said:
Thanks a lot for this guide.
I just installed the latest Phh AOSP 12 GSI (system-squeak-arm64-ab-vndklite-gapps.img.xz) without problems by following your recommendations. I used the lastest twrp_X606FA_11. Flashing dm-verity or Magisk was not required for this GSI to work (it's already rooted). I did have to register my device to solve the "Google Uncertified" issue.
Click to expand...
Click to collapse
Hi, I'm trying to follow what you did, but I'm having issues with the Gapps, do you have some pointers to solve it? Thank you in advance
Hello everybody!
I finally installed CAOS 11 and it's working like a charm. Gapps are definitely working as excpected and system seems to be stable as possible.
I have two question to those that installed it to :
Is anyone kow why some widgets on X606F are not clickable, an do not actualize till reboot?
Am I the only one that lost double tap to wake on CAOS?
Thank you all
I tried AOSP V412 12L too, we lost fingerprint sensor and face unlock, widevine DRM. There is some troubles on wifi, beside of this it is pleasant. Of course this not as smooth as android 10. I do not recommend it for daily basis.
I have tb-X606X. I’ve tried AOSP 11 and AOSP 12, Pixel Exp 11 and 12, LineageOS 11 and 12, but finally I stay with CAOS11, which is from all I tried, the most stable, smooth and bug free.
Btw, I do not have any issue with widgets on CAOS.
And yes, the double tap to wake is lost. I think it is not because of CAOS, it is because of Android 11 and above.
garconblair said:
I have tb-X606X. I’ve tried AOSP 11 and AOSP 12, Pixel Exp 11 and 12, LineageOS 11 and 12, but finally I stay with CAOS11, which is from all I tried, the most stable, smooth and bug free.
Btw, I do not have any issue with widgets on CAOS.
And yes, the double tap to wake is lost. I think it is not because of CAOS, it is because of Android 11 and above.
Click to expand...
Click to collapse
Thanks for the feedback. What about Widevine L1 and SafetyNet test with CAOS11? Are you able to play content at 1080p resolution with the Netflix App?

(S4 GT-i9506) TWRP for Android 13 ?

Hi, so my phone is running Android 13 (LineageOS 20.0) and i have TWRP (3.5.2_9-0) installed, recovery was working before flashing Android 13 but now it wont boot for some reason (stuck on TWRP splash). I think i need an higher version of TWRP. If anyone could help or provide a link it would be really helpful. (Also my phone is currently rooted using Magisk)
VistaSlayer said:
Hi, so my phone is running Android 13 (LineageOS 20.0) and i have TWRP (3.5.2_9-0) installed, recovery was working before flashing Android 13 but now it wont boot for some reason (stuck on TWRP splash). I think i need an higher version of TWRP. If anyone could help or provide a link it would be really helpful. (Also my phone is currently rooted using Magisk)
Click to expand...
Click to collapse
LineageOS uses its own recovery. If you wanted to keep TWRP, you should install it in the second step after ROM.zip.
ze7zez said:
LineageOS uses its own recovery. If you wanted to keep TWRP, you should install it in the second step after ROM.zip.
Click to expand...
Click to collapse
Unofficial LineageOS 20.0 Android 13
LineageOS is a free, community built, aftermarket firmware distribution of Android 13 (T), which is designed to increase performance and reliability over stock Android for your device. LineageOS is based on the Android Open Source Project with...
forum.xda-developers.com
I installed LineageOS from here, but there is no install steps :/
VistaSlayer said:
(...)
I installed LineageOS from here, but there is no install steps :/
Click to expand...
Click to collapse
Install LineageOS on ks01lte | LineageOS Wiki
wiki.lineageos.org
The developer does not need to describe the method and variant of installation. It is up to the potential user to find the way and learn it.
ze7zez said:
Install LineageOS on ks01lte | LineageOS Wiki
wiki.lineageos.org
The developer does not need to describe the method and variant of installation. It is up to the potential user to find the way and learn it.
Click to expand...
Click to collapse
In fact, it installed succesfully (phone was on Android 5 ATM) and now TWRP wont boot bcuz it needs to be an updated version but i cant seem to find it. TWRP 3.5.2 wont boot under Android 13, i need 3.7.x
VistaSlayer said:
In fact, it installed succesfully (phone was on Android 5 ATM) and now TWRP wont boot bcuz it needs to be an updated version but i cant seem to find it. TWRP 3.5.2 wont boot under Android 13, i need 3.7.x
Click to expand...
Click to collapse
TWRP doesn't need any android to boot as it uses the recovery partition (in case of S4). All it needs is access to the data partition to save the configuration.
ze7zez said:
TWRP doesn't need any android to boot as it uses the recovery partition (in case of S4). All it needs is access to the data partition to save the configuration.
Click to expand...
Click to collapse
Weird, i cant get TWRP to boot but Lineage Recovery works
VistaSlayer said:
Weird, i cant get TWRP to boot but Lineage Recovery works
Click to expand...
Click to collapse
How did you flash TWRP?
ze7zez said:
How did you flash TWRP?
Click to expand...
Click to collapse
Tried Odin Mode and Official TWRP APP
VistaSlayer said:
Tried Odin Mode and Official TWRP APP
Click to expand...
Click to collapse
Try this Lineage 18.1 first and see if everything works, because everything should work.
ze7zez said:
Try this Lineage 18.1 first and see if everything works, because everything should work.
Click to expand...
Click to collapse
The TWRP from this post boots on Lineage 20, thanks for your help

Categories

Resources