Joying newest Android 10 headunit - Android Head-Units

I am looking for help with joying headunit and Torque Pro app(specifically the Speech alarms feature), it will only tell me that OBD is connected or disconnected, engine is at operating temperature or fault code present if the radio is not on or i close it before the app starts in dashboards, also the maps will not speak directions or route changes as well, and the older PX5 unit i had from 2018 had a navigation sound mode that you could select <switch> with a GPS mix

Thank You! Sorry i put in wrong format

Related

Android PX3 head unit changed speedo to KM from MPH

Hi ive recently bought a android PX3 head unit, installed it ok but it has changed my milage into KM as im in the UK i need the speedo in MPH, there is a app installed called control settings, in this there is a milage setting set to < KM > but it wont change, most of the settings in the control settings app like temp set to C wont change to F either, indicators set to one flash etc the only setting that i can change is CD indicator.
would anyone know if this could be a software bug with the MCU or the android version?
where would i look for a update? i dont even know who the manifacturer is.
The head unit has no physical buttons only a reset hole so can anyone please tell me how i would get to the recovery screen?
ive never had a android head unit before so dont know much about these units.
Can anyone please help me change/fix this setting or another app or update i can install that can change the milage back from KM to miles,
model px3
android 7.1.2
kernel 3.0.101+
mcu MTCE_KSP2_V2.70a_1
thanks for any help
regards
aliexpress.com/item/Android-7-1-7-Car-DVD-player-GPS-Navigation-Stereo-Audio-Radio-DVD-for-Ford-Fiesta/32839001963.html?ws_ab_test=searchweb0_0,searchweb201602_3_10152_10065_5000015_10151_10344_10068_10130_10324_10342_10547_10325_10343_51102_10340_10341_10548_5130015_10192_10190_10084_10083_10307_10301_10303_10312_10059_10313_10314_10184_10534_5790011_100031_10604_10103_10605_10594_5060015_10142,searchweb201603_36,ppcSwitch_5&algo_expid=239a9acb-5370-48d4-8bfa-8a9d42e57358-35&algo_pvid=239a9acb-5370-48d4-8bfa-8a9d42e57358&transAbTest=ae803_5&rmStoreLevelAB=5
https://www.ebay.co.uk/itm/CTSFO004...sh=item4413f7f882:g:bXAAAOSwhChZrEtd#shpCntId
would this work with the HU, just connect upthe 3 wires? and not connect the HU plug connector that goes to my info screen?
regards
I have the same problem, in the US with a BMW 90 android head unit. I think there is a bug in the MCU firmware that reverts back to Metric units on boot. Lucky for me, I am able to change things from Control Settings app but I do have to do it every time the unit boots. I have reported this to the seller of my head unit but they don't have any solutions. I am hoping they will fix it in the near future.
did you ever get your problem sorted as I now have the same problem
Hi no the seller didnt want to know and just fobbed me off for months before blanking me on whatsapp, no firmware updat as promised, nothing, so what i did was got a set of these:T - 3 Car Intelligent Steering Wheel GPS, hang up/answer, volume setting, music Controller with Noctilucent Function buttons https://www.aliexpress.com/item/Zee...191.html?spm=a2g0s.9042311.0.0.68734c4dUQL81J whicc work quite well, ive also recently ordered a button stalk like how the older radion buttons were: Car steering wheel button remote control lights car navigation DVD / 2 din android Bluetooth wireless Universal remote control,
https://www.aliexpress.com/item/Car...596.html?spm=a2g0s.9042311.0.0.68734c4dUQL81J but im still awaiting delivery of it.
ill be very happy with the stalk as well as the buttons ive stuck to the centre consol, no where near as cool as the steering wheel controls but i really needed my speedo in MPH
anyways hope this helps somewhat not perfect but better than the speedo flashing between KM/MPH
regards
shadowfoxmi said:
I have the same problem, in the US with a BMW 90 android head unit. I think there is a bug in the MCU firmware that reverts back to Metric units on boot. Lucky for me, I am able to change things from Control Settings app but I do have to do it every time the unit boots. I have reported this to the seller of my head unit but they don't have any solutions. I am hoping they will fix it in the near future.
Click to expand...
Click to collapse
I know this is old but I have the same issue with my Joying head unit and my BMW e90. On start up, I have to go into my settings and set everything to American/Imperial units. Did you ever find a fix to this? It's driving me nuts.

New Joying PX5-based Android 8.0 Units - [Rockchip PX5 A53 | Android 8.0 | 4GB RAM]

I installed two different models of Joyings newest PX5-based head units. Both are the 7 inch screen 4GB RAM / 32GB flash double DIN model with flat buttons on the left edge.
Please note that as of May 2018, there appear to be multiple new 4GB / 32GB Joying head units have different internal hardware and are not compatible with each other or with the PX5 2GB Joying head units.
JY-UM128N4PX5 is a QD unit
JY-UO128P4 appears to be an FYT unit
Buyer beware. My recommendation is AVOID the QD based units and seek out the FYT units.
See below for more details.
The following information is for JY-UM128N4PX5. Further down the page is information for JY-UO128P4.
=============== JY-UM128N4PX5 =================
Came with Android 8.0.0 installed.
APP Version TP6735 0.0.65
MCU Version TP6735 4.40
Kernel Version 4.4.103
Master password:126
Password for changing logo:0000
Password for changing UI:8086
So far I have noticed the following:
The unit does not trigger the amplifier turn on signal wire - the orange and black wire labeled AMP-CONT always measures zero volts on my voltmeter. Workaround is to use either the antenna signal wire, or the ACC power signal wire, to turn on your amp. Joying is aware of this issue.
Sleep does not work. The unit shuts down completely about one minute after you turn off the vehicle's ignition. It doesn't sleep and then come back on instantly like my Intel-based Joying unit. Boot time is about 20 seconds. Joying support now says that sleep is not supported on the QD units.
I cannot find the radio settings in the new radio app. You used to be able to slide the bar at the bottom of the radio app to get to settings. Now in Android 8, there are a couple of radio settings that have been moved to the main android setup dialog.
Some of the functionality of the former car settings app has been moved to the android settings dialog. But not everything is there - for example this is where I was looking for the ability to tell the unit to toggle the amplifier signal wire. I could not find any such setting.
AM radio reception is non-existent - static on all AM channels.
FM reception is good, but I cannot figure out how to get the FM Radio to enable display of song and station information - this used to be under RDS settings, which no longer exist.
Bluetooth calling works fine. Seems more stable than my older Intel-based unit.
Sound quality is good - I am using an external amplifier.
The logo set up is missing Porsche and Saab Logos. My Intel-based Joying unit had these. Easy enough to load my own custom logo.
The unit ships with Joying's "Launcher3" selected. On the home screen, the labels of the bottom row of icons are cut off. The screenshots on Joying's website show the same thing. The joying2 launcher is missing.
If you reflash the unit, the vertical keypad on the left side of the unit gets un-mapped and stops working. Fix is to go into car settings and remap it.
========================= JY-UO128P4 ==================
Android Version 8.0.0
Build Number px5-userdebug 8.0.0 OPR5.170623.007
System Info APP 1024x600 2018-04-27 21:42:36
MCU Version 2018-01-23 10:59:33 JY_(R68)_R-86C-096I-NC-NP-1.0-P12S
Passwords:
Factory settings: 3368
Developer Options: 3368
Reset: 3368
Password for changing Launcher:8086
Password for changing screen current:
So far I have noticed the following:
The software on the JY-UO128P4 is very close to that of my older Joying Intel based system.
The developer has replaced all of the system settings screens native to android with their own settings screens. Not super cool. All of the car settings and android system setting are now intermingled.
Upon unboxing, the JY-UO128P4 has only a single Wifi antenna wheras the JY-UM128N4PX5 had two (diversity) wifi antennas. I have not tried to compare reception differences.
The amplifier turn on signal now works as expected (AMP-CONT wire correctly signals 12V when unit is active)
Sleep works as expected
AM radio reception works weakly.
The FM radio application works as expected. Radio app settings are accessed within the radio app. It's possible to enable RDS for song and station ID within the radio app.
All of the joying launchers are available - I prefer launcher 02 and it's available on this unit.
Many more car logos are available on the system. Porsche logo was built-in.
The only things I've noticed so far that are worse with the JY-UO128P4 than the JY-UM128N4PX5
The unit suffers from the android 8.0 bug on Joying where all of your google contacts are deleted if you allow your account on the head unit to sync contacts with google.
As noted above - the native android settings panels are all removed.
The app for setting the color of the buttons on the side panel is limited to pre-determined solid colors - yellow, white, red green etc. On the JY-UM128N4PX5 you could select and set any RGB color, which made it possible to match the button illumination to your other dashboard lights.
As I learn more, I will post more.
ddruker said:
I just installed Joying's newest PX5 head unit. It's the 4GB model.
It came with Android 8.0.0 installed.
APP Version TP6735 0.0.65
MCU Version TP6735 4.40
Kernel Version 4.4.103
So far I have noticed the following problems:
The unit does not trigger the amplifier turn on signal wire - the orange and black wire labeled AMP-CONT always measures zero volts on my voltmeter. Workaround is to use either the antenna signal wire, or the ACC power signal wire, to turn on your amp. I found another post of someone else who had this same issue.
I cannot find most of the passwords needed to set up the unit. The master password is 126 - I found that by watching a joying video. But I cannot find the second level passwords for changing the logo, changing the launcher, etc. Anyone have the other passwords?
The utility to change the color of the buttons on the left side of the unit works, but the buttons do not illuminate one the unit is booted.
I cannot find the radio settings in the new radio app. You used to be able to slide the bar at the bottom of the radio app to get to settings. Now in Android 8, there are a couple of radio settings that have been moved to the main android setup dialog - but for example I cannot find a setting to turn on the functionality to identify song and station names.
Some of the functionality of the former car settings app has been moved to the android settings dialog. But not everything is there - for example this is where I was looking for the ability to tell the unit to toggle the amplifier signal wire. I could not find any such setting.
I cannot figure out how to change the launcher - with the default launcher the lower row of app icons is only half visible on the screen.
Who else has a new Joying Android 8 unit - what else are you seeing? Has anyone found solutions to the items above?
Click to expand...
Click to collapse
I have had several back and forth emails with Joying support in the last couple of days.
They are trying to find the passwords for their new units under Android 8. Support didn't know. They had me try 00000 and 123456, neither of which worked. I told them the main password is 126 - they didn't know this either. I still need passwords for all of the second level settings - change the launcher, change the logo, see if there are more developer options for car config, etc.
They are apparently aware that the AMP-CONT lead to turn on the external amplifier does not work. They recommend connecting the accessory wire from your vehicle to the amp signaling wire instead, so the amp will turn on when you turn your key to the accessory or on position, bypassing the head unit.
They acknowledge there are no detailed settings available for the radio under Android 8 in the radio app. So there is no way to turn on station or channel ID for US customers.
I also let them know about another radio issue - FM Radio reception is normal, but AM reception is awful to non-existent.
Google maps is ok, directions from Google maps are mixing with other audio ok.
Feels like Android 8 on the new Joying 4GB units isn't quite ready for prime time yet... Has anyone tried to upgrade a 2GB Android 6 unit to Android 8 now that the Android 8 files are on Joying's website? Do you see the same behaviors, or am I seeing hardware issue with the brand new 4GB units? I suspect it's all software, but would be nice to know.
ddruker said:
Feels like Android 8 on the new Joying 4GB units isn't quite ready for prime time yet... Has anyone tried to upgrade a 2GB Android 6 unit to Android 8 now that the Android 8 files are on Joying's website? Do you see the same behaviors, or am I seeing hardware issue with the brand new 4GB units? I suspect it's all software, but would be nice to know.
Click to expand...
Click to collapse
The 2GB units are not compatible with the 4GB units. They need different hardware drivers and different MCU firmware as the firmware in the 2GB units is from FYT. I forgot the manufacturer of the 4 GB units but @gtxaspec knows.
There is no downloadable firmware yet for the 2GB units.
hi, i've the same unit and the password was noted into the user manual, it's 3368.
If you buy Joying android 8.0 unit the SKU like:JY-UO135N4PX5 or JY-UOS03N4PX5,password as below:
Master password:126
Password for changing logo:0000
Password for changing UI:8086
TomTom
It seams to be so hard. Again an Android HU, where TomTom navigation does not work. It let's me download the maps, but after that it crashes every time I try to load the application.
I can confirm these passwords are correct:
Master password:126
Password for changing logo:0000
Password for changing UI:8086
Other findings so far:
The illuminated buttons do work - they sometimes take a few seconds to come on after your illumination wire signals with 12V.
The logo selection with this new unit does not include Porsche or Saab. You can still upload your own custom logos.
I updated the unit to the latest (2018-4-20) release on the Joying website which is supposed to include optimizations and Zlink and my unit is now hanging at the Android text logo (right after the animated Android logo). I sent a note to Joying support for help and will also wait for a few hours to see if it comes back to life.
ddruker said:
I can confirm these passwords are correct:
I updated the unit to the latest (2018-4-20) release on the Joying website which is supposed to include optimizations and Zlink and my unit is now hanging at the Android text logo (right after the animated Android logo). I sent a note to Joying support for help and will also wait for a few hours to see if it comes back to life.
Click to expand...
Click to collapse
The same happened to me
After writing about 25 emails with Joying support I had to reflash the whole system ... loosing all my data.
For now I am really not going to try any more updates from Joying with this unit.
Really hoping for a Custom Rom & Root for this unit.
I have one of these as well. Any one find where the setting is to make the sleep mode last longer(2hrs) before it full shuts down? it seems to be locked on 30sec currently. Also it wont pair with my OBDlinkMX BT dongle. in the older MTCD units, making the BT password 1234 let you do it, but not here. anyone have any luck with BT OBD dongle pairing?
I was really leaning towards getting this unit but have been holding off because I wish it had Bluetooth 5.0, maybe I should wait a little longer since it seems to have a fair amount of bugs. I know a lot of people are happy with the Xtron since it has all the best features I just really prefer to have the buttons on the left like this unit has. Looking forward to seeing if you guys can get this squared away
peregrines said:
The same happened to me
After writing about 25 emails with Joying support I had to reflash the whole system ... loosing all my data.
For now I am really not going to try any more updates from Joying with this unit.
Really hoping for a Custom Rom & Root for this unit.
Click to expand...
Click to collapse
I was able to get my unit working again by reflashing. It took about 10 tries with three different USB cards but it finally worked. Joying support provided a file that included a system image and a Window-based chinese language USB card writing programs, along with a word document with instructions. You build the USB drive and then plug it into the left hand USB connector, and click the reset button on the front of the unit. It loads, then tells you to remove the USB drive, and then if you are very lucky it will reboot into Android.
After re-flashing, the vertical keyboard on the left side of the unit did not work. Turned out the mappings had been erased. Fix is to remap the keys - there is an option in car settings.
Current issues still present in the unit seem to be:
Unit shuts off entirely after 30-60 seconds instead of sleeping when you turn off the vehicle. My intel-based unit sleeps for several days.
No AM radio reception - static on all channels.
No way to turn on song or station identification in the radio settings for FM.
AMP-cont signal wire does not work. I've worked around by wiring my accessory wire directly to my amp's signaling wire.
Have not tried Torque and Bluetooth ODBII reader pairing yet - on my list for this weekend.
So, it's not just me...
I purchased a JY-UM135N2PX5 (PX5 2G/16G) with Android 6.0 mid to late March.
I had it on my bench through April, testing and configuring it prior to install.
After trading emails with Joying tech support, I was sent an Android 8.0 update to address a Zlink/iPhone issue.
I started my install in the car today, and discovered "no sound". I guessed that the AMP-CONT wasn't turning on the OEM amplifier. I rechecked the cables, which checked out just fine. Tried a Joying JY-UM135N2 (Intel Sofia 2G/32G Android 6) on the same harness, and it functioned as expected (turned the OEM amplifier on and had sound). I took them both back to my bench and noticed that the "AMP-CONT" on the PX5 unit did not appear to have 12V on it, while the Sofia unit did.
I did not leave the non-functional PX5 unit in the car long enough to see any other issues.
I am curious if I were to revert back to Android 6 on the PX5 unit, if it would fix the AMP-CONT issue (at the cost of breaking the Zlink/iPhone functionality)
ddruker said:
I was able to get my unit working again by reflashing. It took about 10 tries with three different USB cards but it finally worked. Joying support provided a file that included a system image and a Window-based chinese language USB card writing programs, along with a word document with instructions. You build the USB drive and then plug it into the left hand USB connector, and click the reset button on the front of the unit. It loads, then tells you to remove the USB drive, and then if you are very lucky it will reboot into Android.
After re-flashing, the vertical keyboard on the left side of the unit did not work. Turned out the mappings had been erased. Fix is to remap the keys - there is an option in car settings.
Current issues still present in the unit seem to be:
Unit shuts off entirely after 30-60 seconds instead of sleeping when you turn off the vehicle. My intel-based unit sleeps for several days.
Poor AM radio reception
No way to turn on song or station identification in the radio settings.
AMP-cont signal wire does not work. I've worked around by wiring my accessory wire directly to my amp's signaling wire.
Have not tried Torque and Bluetooth ODBII reader pairing yet - on my list for this weekend.
Click to expand...
Click to collapse
Would you be so kind as to share those files with us? This would be a good starting point for further testing and research. Simply upload to a hoster like mega.
z0rn said:
Would you be so kind as to share those files with us? This would be a good starting point for further testing and research. Simply upload to a hoster like mega.
Click to expand...
Click to collapse
Here is a link to the zip file from Joying with the firmware image for reflashing, their USB drive utility, and instructions...
https://drive.google.com/open?id=13HXHRRfuduhIYV41pjQlvsJ0o3xesNBC
Here is the reply I got from Joying support this morning in regards to the open defects I am tracking with the unit. I suspect that all of this will get fixed in subsequent software releases, it's relatively obvious stuff. Can anyone confirm if these same issues exist in the Android 8 builds on Joying's 2GB PX5 head units, or are these unique to the newest 4GB units?
Dear friend,
Please noted :
1) sorry that your system is different with Intel head unit , it do not have fast boot feature . so it will completely off .
2) for the AM receptions is bad , you need to set the proper time and zone . also the radio area choice .
3) sorry, the head unit you purchased do not have the RDS setting .
4) for the am-cont not voltage , please connect the ACC (red wire ) to your amplifier wire . then can offer 12V .
Hope your noted .
Candy
ddruker said:
Here is the reply I got from Joying support this morning in regards to the open defects I am tracking with the unit. I suspect that all of this will get fixed in subsequent software releases, it's relatively obvious stuff. Can anyone confirm if these same issues exist in the Android 8 builds on Joying's 2GB PX5 head units, or are these unique to the newest 4GB units?
Dear friend,
Please noted :
1) sorry that your system is different with Intel head unit , it do not have fast boot feature . so it will completely off .
2) for the AM receptions is bad , you need to set the proper time and zone . also the radio area choice .
3) sorry, the head unit you purchased do not have the RDS setting .
4) for the am-cont not voltage , please connect the ACC (red wire ) to your amplifier wire . then can offer 12V .
Hope your noted .
Candy
Click to expand...
Click to collapse
Are they serious? I would suggest to try the Malaysk Rom, i guess your units are MTCD and MTCE devices so maybe this rom would support the missing software like rds and the other hardware not supported by Joying
https://www.youtube.com/watch?v=WWvgrcn_As8
https://forum.xda-developers.com/an...-malaysk-roms-px5-2-4-gb-8-0-android-t3762724
Good luck!
Flemischguy said:
Are they serious? I would suggest to try the Malaysk Rom, i guess your units are MTCD and MTCE devices so maybe this rom would support the missing software like rds and the other hardware not supported by Joying
Click to expand...
Click to collapse
These units are NOT MTCD/E. Do not use the Malaysk ROM.
---------- Post added at 07:08 PM ---------- Previous post was at 06:53 PM ----------
ddruker said:
Here is the reply I got from Joying support this morning in regards to the open defects I am tracking with the unit. I suspect that all of this will get fixed in subsequent software releases, it's relatively obvious stuff. Can anyone confirm if these same issues exist in the Android 8 builds on Joying's 2GB PX5 head units, or are these unique to the newest 4GB units?
Dear friend,
Please noted :
1) sorry that your system is different with Intel head unit , it do not have fast boot feature . so it will completely off .
2) for the AM receptions is bad , you need to set the proper time and zone . also the radio area choice .
3) sorry, the head unit you purchased do not have the RDS setting .
4) for the am-cont not voltage , please connect the ACC (red wire ) to your amplifier wire . then can offer 12V .
Hope your noted .
Candy
Click to expand...
Click to collapse
I have a 2GB Android version 8.0.0 unit, but my unit is a FYT based unit like the Sofia 3GRs, unlike yours which is a QD unit.
Mine does have fast-boot as my unit is a FYT based unit, using the same hardware/SOM as the Sogia 3GR intel units.
I never used AM-reception. I wouldn't know, but I know from previous users on Sofia 3GR that they also complained about the AM reception
Which RDS-setting? This is so confusing and so not concrete. RDS is a complete set of functions. The syu/FYT based software on the FYT based units support RDS-PS, RDS-PTY and RDS-TA/TP. The latest firmware versions on FYT units (Sofia 3GR and my PX5) also support RDS-RT. They do not support RDS-AF. They implemented "something" like AF. If you use that option it does not select the Alternate Frequency of your radio station, it selects the strongest signal it can find of any station. Note that it is the software. The radio chips in all these units support the complete RDS set of functions.
Don't know about the the amp-cont wire.
You ask about and mention AM and about RDS. I hope you know that RDS can only be used on the FM signal. RDS is not available for AM.
Help
Heres a link I need help to identify my android head unit
https://app.box.com/s/o90d0lnjrqqlek5w1q6lekaj5dgsa20y
Traww said:
Heres a link I need help to identify my android head unit
https://app.box.com/s/o90d0lnjrqqlek5w1q6lekaj5dgsa20y
Click to expand...
Click to collapse
You have an Allwinner T3 chipset in your unit.
Do not use a Joying thread to ask a completely off-topic question.
I've received the same unit, facing the same issues as the OP.
Also the localisation in my language is quite poor.
surfer63 said:
These units are NOT MTCD/E. Do not use the Malaysk ROM.
Click to expand...
Click to collapse
I've bought this unit in the hope that it would be compatible with custom ROMs.
Are you saying that the unit MCU is almost unknown and that no custom ROM would be available in the near future?

Mitsubishi Outlander 2gen (2010-2012) with rockfordfossgate w/sub MMCS w/rear cam

Hi
I have a Mitsubishi outlander 2011 with rockfordfossgate MMCS system and rear view cam.
I have now installed a Dasaita PX5 Octa Core 64 bit 4gb Ram 32 G rom with Android 8.0 I am currentely using Hal9K rom version 3.1.2 works great
I have got everything working, rear view camera (had to solder a bit to get the original camera to work.)
All speakers with sub working, with the original amplifier.
But i can't fade/balance speakers, don't know if thats posible to fix?
Tone controll working fine.
But i am missing some featurers, I am not sure if it is possible to get it to work?
In my MMCS unit i had the opportunity to change car settings "see attachments".
Like how the wipers shall act and things like that.
I also hade speed signal and fule consumption information.
Not sure if the canbus for my dasaita support this?
In the factorysettings on my dasaita i have choosen canbus (111 Mitsubishi pajero&outlander%asx&lancer(simple)
Steering whell controlls working fine, when i put the car in revers i get the rearview camera and that is working fine.
I have see people talking about car_info app, vehicle.apk and controllinfo apps, this are apps working in the background like the rearview camera app right?.
But i get no icons for this apps on my head unit, and nothing in extra menu or car setting menu.
I do not get any signal when opening doors og changing temperatur on the AC and things like that.
So my question is simple, is there any way for me on my car to get the opertunity to change the settings link a was able to do in the original MMCS unit?
In the MMCS hadde an "equpment" meny, that i do not have now. I also like for information like speed signal, doors opening and things like that be poping up on the unit.
Or is this settning for the equipment and speed signa, doors just not supportet with my canbus decoder?
Is there any other way to get to this equpment setting in my car without installing the original MMCS unit?
Mayby with ODB2 or something like that?
knutmw said:
Hi
I have a Mitsubishi outlander 2011 with rockfordfossgate MMCS system and rear view cam.
I have now installed a Dasaita PX5 Octa Core 64 bit 4gb Ram 32 G rom with Android 8.0 I am currentely using Hal9K rom version 3.1.2 works great
I have got everything working, rear view camera (had to solder a bit to get the original camera to work.)
All speakers with sub working, with the original amplifier.
But i can't fade/balance speakers, don't know if thats posible to fix?
Tone controll working fine.
But i am missing some featurers, I am not sure if it is possible to get it to work?
In my MMCS unit i had the opportunity to change car settings "see attachments".
Like how the wipers shall act and things like that.
I also hade speed signal and fule consumption information.
Not sure if the canbus for my dasaita support this?
In the factorysettings on my dasaita i have choosen canbus (111 Mitsubishi pajero&outlander%asx&lancer(simple)
Steering whell controlls working fine, when i put the car in revers i get the rearview camera and that is working fine.
I have see people talking about car_info app, vehicle.apk and controllinfo apps, this are apps working in the background like the rearview camera app right?.
But i get no icons for this apps on my head unit, and nothing in extra menu or car setting menu.
I do not get any signal when opening doors og changing temperatur on the AC and things like that.
So my question is simple, is there any way for me on my car to get the opertunity to change the settings link a was able to do in the original MMCS unit?
In the MMCS hadde an "equpment" meny, that i do not have now. I also like for information like speed signal, doors opening and things like that be poping up on the unit.
Or is this settning for the equipment and speed signa, doors just not supportet with my canbus decoder?
Is there any other way to get to this equpment setting in my car without installing the original MMCS unit?
Mayby with ODB2 or something like that?
Click to expand...
Click to collapse
Where u able to figure any of this out?
Sent from my SM-G975U1 using Tapatalk
I have 2008 Pajero Exceed.. whilst older than yours.
It doesn't have the extra menu controls you're also missing
I was looking at a system fully installed Extnix $600
But didn't follow through.
They advised me everything would work including amp -EXCEPT the fade/balance, so it might be a bit more embedded into the Mitsubishi system and missing from alternative head units ?
I'm really interested for this topic. I have a Mitsubishi Outlander and it would be great if I could still have stock MMCS settings on an aftermarket android unit.
nickgrserifos said:
and it would be great if I could still have stock MMCS settings on an aftermarket android unit.
Click to expand...
Click to collapse
What do you mean "stock MMCS settings"
kiwi-oz said:
What do you mean "stock MMCS settings"
Click to expand...
Click to collapse
Mitsubishi Multi Communication System.
nickgrserifos said:
Mitsubishi Multi Communication System.
Click to expand...
Click to collapse
What do you mean
"Stock Mitsubishi Multi Communication System settings on an Android unit"
You wrote it
I know what MMCS is
@nickgrserifos
Do you currently have a GPS unit ? (MMCS)
kiwi-oz said:
@nickgrserifos
Do you currently have a GPS unit ? (MMCS)
Click to expand...
Click to collapse
Yes, I do have a gps unit. But if I install an aftermarket android unit I will loose all stock mitsubishi car settings like remote car pre-heating, consumption information as well as other important car settings .
nickgrserifos said:
Yes, I do have a gps unit. But if I install an aftermarket android unit I will loose all stock mitsubishi car settings like remote car pre-heating, consumption information as well as other important car settings .
Click to expand...
Click to collapse
aaaah Ok... Pajero Exceed 2008 MMCS doesn't integrate any car functions (just Bluetooth)
kiwi-oz said:
aaaah Ok... Pajero Exceed 2008 MMCS doesn't integrate any car functions (just Bluetooth)
Click to expand...
Click to collapse
Yeah my bad I didn't clarify that from the beginning. I have a 2015 Outlander PHEV.

chinese head unit for opel insignia - 8581

Hello, after many month of thinking what to put in my car, I decided not to risk with ones straight from china , even though they have a great design , their prices went quite up. So I bought one from my country which again is Chinese but has 2 years warranty. It has the following specs: Android 11 - octa-core CPU, 4 GB RAM, 64GB ROM, RDS, DSP, CARPLAY . A decent launcher design. After I had it put in my car there are some problems of course...
First of all my dashboard became Chinese , secondly the steering wheel controls don't work. I searched for information and found that I can go in factory settings and change the can bus software or something. I found out I can get in these settings with the password 3368 . And there are many types of CAN BUS settings. Around 5-6 have Opel Insignia . So far I tried 3 and it doesn't work - it doesn't prompt me to reboot but I do it anyway. Also in the navigation "car settings" it just seems like it doesn't talk with the car at all. At least I got to put the Opel logo for boot up animation.
Climate control works from the old knobs , and does not visualize on the screen - this is not really a problem for me but still wonder why doesn't it work. Also i got a OBD II dongle which lights up when i plug it in and the navi Bluetooth finds it , but i cant connect to it - it wants a passcode and 0000,8888,3368 don't work .
Now for what DOES work - the new rearview camera starts when I put it in reverse , but the lines don't bend. Music comes out of the speakers . Blinkers and hazards and chimes have e new bad sounding beep , but at least there is some communication with the car. Sport and Tour buttons work ! The mechanics which put in the new unit took out the whole cd changer , I don't know why and if it was necessary and if it is a problem. Park assist also work and the button but it also has changed chime sounds.
When i contacted the sellers they told me they just sell, and don't know much about installations.. they told me its model is just "8581" not really helpful like the Chinese supports which i expected to avoid.
Any help will be greatly appreciated !! Mainly i want to fix my dashboard to be in English again(when the battery disconnects and the computer resets , it usually goes back in German, never Chinese) And the other thing is to get the steering wheel buttons to work and along with it to have more communication between the car and the navigation unit.
Try reading forums and posting what has been tried, or at least try to figure out what the unit is
https://www.facebook.com/video.php?v=1053379798745114
Log in or sign up to view
See posts, photos and more on Facebook.
www.facebook.com
8581 9 Coll Carplay Android 10 4gb Ram Hd Player Car Accessories Headunit Tv Dvd Player Car Stereo Radio Android 9 Inch - Buy Android 9 Inch,10 In 4gb Stereo 2 Din Car Players 9 Inch Android Stereo Player Android 9 Inche Stereo,Single Din Android 10
8581 9 Coll Carplay Android 10 4gb Ram Hd Player Car Accessories Headunit Tv Dvd Player Car Stereo Radio Android 9 Inch - Buy Android 9 Inch,10 In 4gb Stereo 2 Din Car Players 9 Inch Android Stereo Player Android 9 Inche Stereo,Single Din Android 10 9 Inches Android Car Ips Radio Gps Wifi 128 Gb...
www.alibaba.com
I found those. But it helps me in no way.
The problem was a wrong connection on one of the many cables . Now everything works , and im quite happy with the unit. I dont know in what standby mode it stays but it boots up for seconds, another 5 seconds for the wireless car play and the music starts automatically from Spotify and the maps are ready to navigate. My car leveled up
ivosto said:
The problem was a wrong connection on one of the many cables . Now everything works , and im quite happy with the unit. I dont know in what standby mode it stays but it boots up for seconds, another 5 seconds for the wireless car play and the music starts automatically from Spotify and the maps are ready to navigate. My car leveled up
Click to expand...
Click to collapse
Hi mate hope your well I've currently got the same problems you had with my trip going Chinese and steering wheel not working or the heating on the radio any more information would be great cheers
tommytommy1990 said:
Hi mate hope your well I've currently got the same problems you had with my trip going Chinese and steering wheel not working or the heating on the radio any more information would be great cheers
Click to expand...
Click to collapse
Hi all, I have same problem can anyone help at all. Thanks in advance

Loss of reversing beeps with Android PX6

Hello,
By installing a PX6 car radio on a 2006 Peugeot 407 coupé, I lost the following functions; Back-up beep forward and Back-up beep back.
The reversing beeps are materialized by a drawing of the car on the screen and green, yellow and red lines depending on the distance from the obstacle. (cf attachments)
Is my CANBUS system well suited/adapted to the car?
Is it possible to reprogram it?
Do you have any other solutions to offer.
Thanking you in advance for your help.
I found element of response in this forum but it seems really complicated to solve the problem
I have the same problem at @Zoran1993
Android 9 Pie PX5 Peugeot 407 Canbus Problem
Hello I have a problem with my Android 9 Pie PX5 multimedia for Peugeot 407, Canbus doesn’t work well he is late with commands AC and steering wheel, I don’t have parking assistance, when I open the door the canbus turn on and work very short...
forum.xda-developers.com
Thks for your help

Categories

Resources