Hello guys, I have a Ticwatch E2 and today i softbricked it and i cannot find how to open fastboot or recovery mode directly from watch not from adb (adb reboot bootloader etc.)
so i was checking some websites and then i found how to open bootloader on LG G Watch R so i tried it and it worked
So here is How to Open Fastboot mode
Turn off the watch and then turn it on normally OR Press and hold Power button for about 10 sec. to reboot it.
Keep holding power button and wait for TICWATCH logo to appear on screen.
Start tapping the screen with two fingers, one on the top left and one on the bottom right ,while pressing and holding the power button
Release power button and stop tapping screen after you hear three vibrations.
So now you are in fastboot mode, short tap to power button changes option and holding power button selects option.
Also here is how to open Recovery Mode
Do the exact steps to enter Fastboot, after entering fastboot short press power button to change option and find Recovery Mode,
Then press and hold power button to select it.
Watch will reboot and recovery mode should open, if you stuck at Android Robot and recovery menu is missing,
Just press and hold power button an swipe screen up and release power button, menu should appear.
swipe up / down and left/ right to use recovery mode.
How to Unlock Bootloader Lock
Warning! All data will be wiped after unlocking bootloader.
Open Fastboot Mode and put your watch on the charging dock, connect it to pc and open command prompt then type
"fastboot oem unlock" and there will be some warning appears on cmd then type the same command again to unlock bootloader.
How to ReLock Bootloader Lock
Warning! All data will be wiped after unlocking bootloader.
Open Fastboot Mode and put your watch on the charging dock, connect it to pc and open command prompt then type
"fastboot oem lock" and there will be some warning appears on cmd then type the same command again to lock bootloader.
How to open TWRP
Download TWRP
Open Fastboot and Unlock Bootloader Lock,
then type "fastboot boot twrp_ticwatchE2-S2.img" to boot twrp.
Warning! Use it carefully.
MTP DOESNT WORKS use adb shell, adb pull or adb push commands.
I got my hands on a cheap Ticwatch S2 and i asking myself, what is the benefit of TWRP/root on a smartwatch?
I mean, ok i can make backup in TWRP or flash things, but it seems that there is no custom rom for this model, so root seems to be the only thing to achieve. But what can I do with root on a smartwatch?
old.splatterhand said:
I got my hands on a cheap Ticwatch S2 and i asking myself, what is the benefit of TWRP/root on a smartwatch?
I mean, ok i can make backup in TWRP or flash things, but it seems that there is no custom rom for this model, so root seems to be the only thing to achieve. But what can I do with root on a smartwatch?
Click to expand...
Click to collapse
kali linux nethunter fully supported on the ticwatch pro.... reduced functionality on other devices.... but a functional pentest platform on my wrist is pretty dope to me
Related
Hello all,
I am trying to install Cyanogenmod on my Nexus 10. I followed the instructions on the Cyanogenmod wiki (I can't link to them as a new user). I got as far as these instructions to unlock the device:
Enable USB debugging on the device.
Connect the device to the computer through USB.
From a terminal on a computer, type the following to boot the device into fastboot mode:
Code:
$ adb reboot bootloader
From the same terminal, type the following command to unlock the bootloader (under Linux, you must be root):
Code:
$ fastboot oem unlock
A disclaimer will display on the device that must be accepted. Use the volume keys to cycle through the options. Pressing the power button should confirm your selection.
If the device doesn't automatically reboot, reboot it from the menu. It should now be unlocked. You can confirm this is the case if you see an unlocked icon at the bottom of the Google boot screen during reboots.
However, the device never rebooted. It just shows the glowy nexus X logo indefinitely. If I reboot to the bootloader, I get options for recovery mode, however the device does not show up on fastboot or adb from my computer in recovery mode, so I don't know what to do.
I am new to the world of unlocking and custom roms and whatnot, and am worried that I just bricked my tablet . Thanks for reading.
OK, I found the answer searching online. A video on youtube explains it. The forum won't let me link the video, but the youtube id is T1Se7Hr9Cww. Put that after the "v=" in a youtube URL and you'll get there.
explains how to fix it. Evidently unlocking the boot loader doesn't reset the device, but the device must be reset to continue. So you need to do mash all the buttons in recovery mode to bring up a menu to delete your stuff.
Hey guys, I had Lollipop 5.0 and I did stock rom flash in Nexus Root Toolkit to install 5.0.1, everything went smoothly and it started to boot, I waited for more than 20 minutes. Then I decided to do it again and it was really hard to get into fastboot, I had to disconnect the battery and try for some more time. When I finnaly get into fastboot mode I have tried reinstalling 5.0.1, installing 5.0, 4.4.4 and even Cyanogen's last nightly. With any of those I had no luck as it is stuck with boot animation.
Some googling told me about people who did fastboot oem lock and it booted up, just tried that with no luck also.
One very important thing, when I get into fastboot mode, I can only select Start in the device itself, clicking volume up or down doesn't give me any other option.
Edit: I even downgraded Nexus Root Toolkit from 1.9.9 to 1.8.2 thinking it was the problem, no luck. And tried to install Lollipop manually a couple of times. And the problem trying to get into fastboot mode keeps happening.
Thank you all in advance
And now that I tried to lock the bootloader I can't unlock it again because when I go to fastboot mode I can only press start, pressing the volume keys doesn't do anything. What can I do to unlock the bootloader ? I think I'm stuck in here because I can't do anything else without it unlocked.
Edit: It didn't work to boot the system also
I really need some help here
so your volume down key is working when you're entering bootloader mode, but after "fastboot oem unlock" command you can't choose "YES" with the same volume down key ?
RolF2 said:
so your volume down key is working when you're entering bootloader mode, but after "fastboot oem unlock" command you can't choose "YES" with the same volume down key ?
Click to expand...
Click to collapse
All my keys are working just fine, I can easily boot into bootloader (I was doing Power + Volume Down when I should push Power + Volume Down + Volume UP) but when I get into bootloader/fastboot (I don't know which one is the proper name) I can't do anything but press the Power button, meaning that I can only choose START. When I do the fastboot oem unlock command I can't press Volume UP or Down to choose Yes.
I followed this tutorial (http://forum.xda-developers.com/nexus-4/general/tutorial-how-to-unbrick-n4-t2347060) with no luck aswell, I finnaly got into the system, but I can't unlock the bootloader because of the Volume keys problem. I also noticed that even when I'm into the system from that tutorial, which is Jelly Bean btw I still can't use the volume keys.
Basically, phone only recognises volume keys when it's off and I press to go into bootloader or download mode.
Note: Unlocking bootloader will completely wipe your device’s data(Everything like music,
photos, videos & apps).So we highly recommend taking backup of your important data. So take
a backup of your apps and data
IMPORTANT & PREREQUIREMENTS
*Make sure there is at least 60% battery left on your smartphone before begin started
this process
• Install USB Drivers on your computer. ( Drivers are Included on The Zip)
• Enable developer option and usb debugging
NEXT STEP
• Connect your android to your PC with USB cable
• Now go to ADB folder and Open the command window there(Right click on the
empty space inside the folder then select “Open command window here” option to
launch a cmd window)
• Now reboot into the bootloader by issuing the following commands. (Make sure
your device is detected by your PC)
adb reboot bootloader
• Now Check fastboot connectivity by giving the command below.If your device is
connect properly then it should return device code.
fastboot devies
• Once in the bootloader, issue the following fastboot command to unlock the
bootloader. (This will unlock your phone and wipe all data of your device)
fastboot oem unlock
There will be a Warning, Press the Volume up Key to Continue.
Then Restart Your Phone, Setup it, then again enable usb debugging .
RECOVERY INSTALL STEP
1. Open the adb folder ( Recovery Image is already Loaded There)
2. Then open a CMD window inside that folder. To do that, Shift + Right click on any empty
white space inside the folder and then select Open command window here.
3. Connect your Android device to the PC. Type the following into the command window to boot
your device into bootloader/fastboot mode:
adb reboot bootloader
4. Once your device boots into bootloader mode, type this into the command line.
fastboot flash recovery recovery.img
5. Once TWRP is successfully flashed on your device, type this final command to reboot your
device.
fastboot reboot
HOW TO ROOT INTEX AQUA 5.5 VR
Download the Super Su .zip From Downloads Tab
Then Go to TWRP Recovery
Touch on Install
Touch on Supersu.zip
It will install & Patch Boot.img on the fly
XDA:DevDB Information
TWRP for Intex Aqua 5.5 VR, Tool/Utility for all devices (see above for details)
Contributors
Rajarshi2
Version Information
Status: Stable
Created 2017-09-04
Last Updated 2017-09-04
can any one help me to port or create a twrp recovery for mtk device
vicky karthi said:
can any one help me to port or create a twrp recovery for mtk device
Click to expand...
Click to collapse
yes i can , tell me your device name
Lava iris 402 and i need to install twrp recovery in infocus m350 which was in lock bootloader
Ok give me sometime i will help you
Make my phone root adaptable...
Intex aqua s3 . android 7.0... Plz
Rajarshi2 said:
yes i can , tell me your device name
Click to expand...
Click to collapse
Intex aqua 5.5 vr plus
doesn't works!!
In fastboot mode
Press Volume Up key to unlock
Press Volume Down key to abort.
volume down key working perfectly and aborting the mission but VOLUME UP KEY DOESN'T WORKS!
In developer mode OEM UNLOCK is already turned on!
In RECOVERY MODE IT SAYS NO COMMAND.
prit19 said:
In fastboot mode
Press Volume Up key to unlock
Press Volume Down key to abort.
volume down key working perfectly and aborting the mission but VOLUME UP KEY DOESN'T WORKS!
In developer mode OEM UNLOCK is already turned on!
In RECOVERY MODE IT SAYS NO COMMAND.
Click to expand...
Click to collapse
Hey Mate just keep pressing volume up button it will work ..It worked in mine.. BTW it I helped then press the thanks button.
smarty1 said:
Hey Mate just keep pressing volume up button it will work ..It worked in mine.. BTW it I helped then press the thanks button.
Click to expand...
Click to collapse
are you serious? because i tried and nothing happens i pressed VOL UP for 100 times nothing happens pressed VOL DWN 1 time.. it got cancled.
prit19 said:
are you serious? because i tried and nothing happens i pressed VOL UP for 100 times nothing happens pressed VOL DWN 1 time.. it got cancled.
Click to expand...
Click to collapse
While you press volume + hold it ffor some seconds it will work.
I tried with different drivers etc. but its just don't work, i downloaded TOOL ALL IN ONE, but this said that device was found but not said what or which device, only when phone is normally started i see it on the list of "adb devices" and in TOOL ALL IN ONE. Please help thanks in advance =)
Fastboot is an entirely different mode from adb, and as such it requires a different tool. In the console there is a command "fastboot", which is what you need to use to interact with the phone in fastboot mode. You can boot into fastboot mode from power off with the USB to computer plugged in by holding Volume Down, or it might be possible with TOOL ALL IN ONE, I haven't used it much.
Some basic commands:
fastboot flash unlock path/to/unlock.bin # This will flash the unlock bin
fastboot getvar unlocked # This will check if the device is unlocked
fastboot reboot # This will reboot the phone into normal mode, since powering off by holding the power button is a pain
To flash TWRP, there's a more advanced process with some specific requirements, but I'd be happy to share those if wanted.
mwsundberg said:
Fastboot is an entirely different mode from adb, and as such it requires a different tool. In the console there is a command "fastboot", which is what you need to use to interact with the phone in fastboot mode. You can boot into fastboot mode from power off with the USB to computer plugged in by holding Volume Down, or it might be possible with TOOL ALL IN ONE, I haven't used it much.
Some basic commands:
fastboot flash unlock path/to/unlock.bin # This will flash the unlock bin
fastboot getvar unlocked # This will check if the device is unlocked
fastboot reboot # This will reboot the phone into normal mode, since powering off by holding the power button is a pain
To flash TWRP, there's a more advanced process with some specific requirements, but I'd be happy to share those if wanted.
Click to expand...
Click to collapse
Yeah, so I wanted to flash TWRP but it doesen't seem to work i did what was said in many guides but maybe if you tell me how to do it, it will work =) Thanks
So i tried to flash TWRP with the TOOL ALL IN ONE, everything was okey but then error happened called "Unknown device"
First of all, which version of G6 do you have? The US997 one, or the H870?
mwsundberg said:
First of all, which version of G6 do you have? The US997 one, or the H870?
Click to expand...
Click to collapse
H870
For H870 I'm not entirely sure, but I know that for the US997 you have to do a special procedure to make it permanent. Make sure you back up everything first, too.
With the phone in fastboot mode and a computer connected with fastboot installed and the twrp zip downloaded as "twrp.zip" (or whatever you want):
Make sure the bootloader is unlocked: fastboot getvar unlocked (should return "yes" or "true").
Flash the recovery: fastboot flash recovery twrp.zip (replace twrp.zip with the relative or absolute filepath/name).
Unplug the phone from the computer and reboot into recovery by holding Power and Volume Down. When the logo appears, lift your finger off the power button briefly and then continue pressing.
When you get to the factory reset menu hit yes twice, then the phone should boot into twrp (it may flash the LG logo, I've had different behavior on different phones. You won't need to hold the Power-Volume Down combo any more).
In twrp, swipe to allow modification, then in the Wipe menu select Format Data (and enter yes). This will wipe the phone, so make sure everything was backed up beforehand.
From the main menu go to the Reboot menu and select Recovery.
Here it might vary from the US997. Below are suggestions which I think are needed to have it work.
Download the no-verity-opt-encrypt zip, and connect the phone to the computer.
Once it's rebooted into recovery mode: adb push path/to/no-verity.zip /sdcard/
Then from the install menu in twrp install the zip.
Reboot into System from the reboot menu on the homescreen of twrp.
That should do it all.
Does this phone have? Is there a way to boot into such mode so I can flash something via fastboot?
Power and volume down keys just lead to some test mode. Holding the volume down while connecting USB does nothing as well.
I'm just having the same prob with --U51
Thanks
Not meaning to necrorez a thread as the entire forum section is inactive...
On Y625-U21 the best way to enter fastboot mode is via adb:
- activate usb debug
- use "adb reboot bootloader"
you are now in fastboot mode. Notice that on the phone you won't see a special screen: just the huawei logo like it's stuck, but you can use fastboot to do what you want (unlock the bootloader since it won't require codes, run TWRP, flash TWRP etc etc...)