Hi!
I just flashed old G3 with LineageOS 18.1
Everything works just fine until today. It suddenly stopped connecting to WiFi and won't connect anymore.
I tried flashing CyanogenMod 14 but the problem persists.
So everytime I tried connecting to WiFi, it only shows "Connecting...." then "Saved"
Did I just broke something here? Tried searching the forum but i have no luck either.
(I've tried following this thread too, still failed)
Anybody has experienced this before?
Tried this but didn't see any MID Settings, cannot uncheck / generate anything. Only REFRESH.
so install android Marshmallow than follow these steps:
1- on dial pad : *#546368#*855# (855 is for D855 and so)
2- find and click SCV Menu
3-click on CRCWIZARD Test
4-click the tab Auto MID
5- uncheck IMEI in MID settings
6- click generate to generate your new MAC's
7- click MID write
8-Click Refresh to be sure that you changed MAC adress
9-Rebbot phone to take effect!
Click to expand...
Click to collapse
Hey Friend.
It doesn't have to be your device, it's the Lineage 18.1.
it was the same for me... "only saved" but no connection possible.
The LAN didn't work for me even after the successful installation.
No 2.4 Ghz and no 5 Ghz, although password etc. was all 100% correct.
My AVM Fritzbox 6660 Cable is set to WAN WPA2/WPA3.
I need to change that to only WPA2 CWP option, only then could my LG-G3-D855 with Lineage 18.1 use it successfully.
It's the fault of the Lineage programmers !!! something like that simply shouldn't happen with an Android 11.
I had previously installed the old Fulmics 6.9 on the LG G3 D855 and there were no problems with the Fritzbox 6660 Cable and FritzOS 7.29 installed on it, neither in 2.4 nor in 5 Ghz.
Only this LineageOS 18.1 requires the old WPA2 CWP encryption on the Fritzbox 6660 Cable. Ok, so there are no disadvantages for other devices that I still have, such as iPad and iPhone etc. they can also handle the WPA2 CWP.
Still, isn't it okay that such a well-developed Android 11 can't do WPA2/WP3, or is it just LineageOS 18.1 that doesn't? Can the original Android 11 work with it ??
Related
Hello All,
I have upgraded LG G2 to
LP 5.0.2
BB : M8974A-AAAANAZM-1.0.190128
Kernel : 3.4.0
Build : LRX22g
Software Version : v30-eur-xx
i am facing consistent WiFi issue after switching on it gets stuck at Wifi Turning on but does not connect.
It has got an MAC address. sometimes very rarely it may connect to WiFi but then disconnects after 3-4 minutes.
I have tried clear cache, factory reset but problem still there, has anyone faced similar issue and can help me here
many thanks
Did you have a problem before upgrading? If not, then it's unlikely to be a hardware issue and something could have gotten messed up in the update process.
If I were you, I would TOT back to KK following THIS GUIDE. After it installs, do a factory reset. After it restarts, then update to the latest ota and factory reset once more. That will get you a clean install as possible.
Btw, have you tried connecting to another wifi access point? Sometimes networks can be setup incorrectly(ie two routers with dhcp enabled on one network) which can cause problems.
stan54 said:
Did you have a problem before upgrading? If not, then it's unlikely to be a hardware issue and something could have gotten messed up in the update process.
If I were you, I would TOT back to KK following THIS GUIDE. After it installs, do a factory reset. After it restarts, then update to the latest ota and factory reset once more. That will get you a clean install as possible.
Btw, have you tried connecting to another wifi access point? Sometimes networks can be setup incorrectly(ie two routers with dhcp enabled on one network) which can cause problems.
Click to expand...
Click to collapse
Hello Stan54, I rooted my LG G2 last year and was on Kitkat, phone was running fine since that, in December I installed nova launcher and couple of other applications but not able to find the log. After that I started having this issue. One peculiar thing is it can start it's hotspot correctly and I can connect my PC to phone's hotspot WiFi SSID and bluetooth is fine as well but only Wifi keeps stuck at "Turning on" mode.
Since then i have
1. Flashed it to stock JB ROM {Using LG Flash tool}
2. Upgraded to LP5.0.2 using LG PC Suite
still the issue remains
one slight improvement I saw after that is
1. It connects to WiFi for a minute or 2 then goes to "Turning Wifi on" mode
I will try to go back to KK and follow steps as suggested and update.
thanks
Edit : I have tried connecting to other WiFi networks as well, same issue.
hi all,
How do i find which stock TOT kitkat rom to use, my phone details
ANEUBK
<cs_em_flag>N</cs_em_flag>
<cs_em_uri>N</cs_em_uri>
<chip_type>EG</chip_type>
<prod_type>GSM</prod_type>
<buyer>NEU</buyer>
thanks
inkypinky999 said:
hi all,
How do i find which stock TOT kitkat rom to use, my phone details
ANEUBK
<cs_em_flag>N</cs_em_flag>
<cs_em_uri>N</cs_em_uri>
<chip_type>EG</chip_type>
<prod_type>GSM</prod_type>
<buyer>NEU</buyer>
thanks
Click to expand...
Click to collapse
Hi I followed the flash to stock --> factory reset --> OTA upgrade to LP 5.0.2 --> factory reset still have the Wifi issue.
really need some help?
hello Folks any help, really desperate to get my phone fixed.
Hello together,
I run into a big problem. I deciced to try out ZUI, so I converted my international Z1 (from unofficial cm13) to ZUI. I converted to ZUI 0.9 and all was working. Updating to latest Android 5.1.1 based rom also worked. After I updated to the 6.0 based ZUI rom, the connection isnt working anymore.
I´m tested it with the latest 6.0 ZUI ST and with the latest ZUI DEV both had no wifi.
I installed ZUI 0.9 via QFIL without problems.
Hope you have ideas
EDIT: I created an error log via adb bugreport. I logged when I clicked to connect to my wifi network.
error log: https://onedrive.live.com/redir?res...3165&authkey=!ALLtyj116BBeW9E&ithint=file,txt
FINALLY: Ok I fixed it: I changed the security from WPA2-PSK to a open network then it worked. After that was working I changed back to WPA2-PSK and voila all was running normally. Very strange but I´m happy that I can use ZUI with latest version now
use that
http://4pda.ru/forum/index.php?showtopic=701320&st=1380#entry46278823
Gonzaman said:
use that
http://4pda.ru/forum/index.php?showtopic=701320&st=1380#entry46278823
Click to expand...
Click to collapse
Same with that method. The 5.1 build works without problems. After updating via zip OR via ota to 6.1.1 (ZUI 1.6.225), the wifi stops working.
Ok I fixed it: I changed the security from WPA2-PSK to a open network then it worked. After that was working I changed back to WPA2-PSK and voila all was running normally. Very strange but I´m happy that I can use ZUI with latest version now
Have a nice day
Mine got messed up, wifi mac address change to 02:00:00:00:00:00 ,can't turn on wifi and bt anymore
so my x720 has bad wifi. bought this from amazon: CableCreation USB-C(Type C 3.1) to RJ45 Gigabit Ethernet LAN Network Adapter, but it doens't work AICP which I currently flashed.
does anyone know of a combination of a ROM + ethernet USB-C adapter?
thx in advance.
btw, aicp on x720 seems very stable and smooth. thx!
If you will use RJ45 cable then why not just connect it via BT or USB-C tether to get internet connection?
The adapter you mentioned seems to be for a Macbook
Return the adapter you bought and get this one instead.
https://www.amazon.com/Smays-Ethernet-compatible-Raspbian-Raspberry/dp/B00L32UUJK
What is the issue that you are experiencing?
Which phone do you have?
What OS?
I agree with Joms_US you could just connect through BT. But why bother using a bandaid, when you could make work as intended instead.
As long as there is no hardware issue, your connection issue is caused by either your configuration or software. It could also be your router. But unlikely if everything else works okay. Its seems that you are just very likely using the wrong firmware.
thank both of you for the tips and help. what i have is x720+ aicp 13.1 from xdev. the wifi module seem to be dead (as I tried stocked rom as well). The usb tethering is graying out. the BT tethering, i am not sure howto make it to work though. Looks very much my hardware is toasted.
anyway, I will try the link above, and very likely will get the new oneplus 6.
have a nice weekend..
xhunterc said:
thank both of you for the tips and help. what i have is x720+ aicp 13.1 from xdev. the wifi module seem to be dead (as I tried stocked rom as well). The usb tethering is graying out. the BT tethering, i am not sure howto make it to work though. Looks very much my hardware is toasted.
anyway, I will try the link above, and very likely will get the new oneplus 6.
have a nice weekend..
Click to expand...
Click to collapse
Don't give up yet, this is very likely something that can be fixed. As I mentioned previously you very likely have the wrong firmware. Go to the bottom of my post here: https://forum.xda-developers.com/le-pro3/development/le-eco-pro-3-x727-twrp-backup-clean-t3727920
Download the firmware for your device : if its an X727 - download the X727 firmware and then boot to TWRP Recovery
Once in TWRP -
Click select storage and choose the local drive
Click Install button : From here, you'll be shown your device's internal storage folder tree: Go to SDcard > downloads > select the firmware you just downloaded
Swipe the slider at the bottom to flash the firmware
Go to wipe> Advanced wipe > Check Cache ( Cache only) Swipe
Reboot to Recovery- (Check any boxes to install TWRP manager IF you see them) > Reboot to system > issue should now be resolved
Another hint
Click the reply button for whoever you are talking to in these forums otherwise that person will never know that you responded unless they just happen to open the link again.
If this does not resolve the issue, there are other things to try.
Hello everyone, ive been working on a custom rom, and i like to share with you guys this rom which i have ported ( Lineage 14.1 for our dearly asus zenfone 3 max) which is currently not that stable yet but it has good battery backup , good for daily driver. i will post a patch for fixing bugs soon...
NOTE: This rom is for asus ZC520TL, having MT6737M chipset only.:fingers-crossed:
Things you need:
*Rooted and TWRP install link: https://www.youtube.com/watch?v=Nu7QhMQ-2eI
*Latest stock android 7.0 with lastest security patch (July 5, 2018).
* Lineage_14.1_Unofficial link: https://drive.google.com/open?id=1bZ_z_lzfHfmCbjxjEloXEDOU9ZEU2fln
Features:
All Lineage OS features
what is working:
1. RIL (call,data,sms) except volte
2. Dual sim
3. Dual sim 4G
4. WIFI
5. Hotspot
6. 4G/2G/3G switch
7. F.M radio
8. VPN
9. Youtube
10. All storage mount and also OTG
11. Audio
12. Offline charging and many more
NOT WORKING:
1. Bluetooth
2. Finger print
3. camera
INSTALLING PROCEDURE (TWRP):
1. Take a full Nan-droid backup first
2. Open WIPE/Advanced/ and format system, cache & data first.
3. Now install the Rom.
4. Install Gapps. (pico recommeded but its your choice).
5. Wipe Dalvik/ART cache
6. Reboot
Now it will take 10-15 mins to boot-up
No network after installation completed?
-> go to setting /Simcard /sim1 or sim2 setting and change to your desired network.
No navigation button?
-> go to settings/Button...
Wow...looks like there's a hope for this Asus device.
Any update on the camera, or is it possible to use third party camera apps?
Update: I've tried it but it does not detect SIM. I don't know why, it just says "Empty Slot" on either SIM 1 or 2.
EDIT: I think it's IMEI issue, which I've read very common to Asus phones.
Thanks for this! Looking forward to the bluetooth and camera fix. Shame there's not much love for this phone...
Great! can you share how you get it to work? I would try to compile it myself but I never done it before on an unsupported device...
Sir, how did you update your mt6737m to nougat?
Ive downgrde my phone to mm, (Im on oreo)
Then they said that you need to unlock bootloader 1st to proceed root and install twrp aswell..
Can you provide me a link on nougat version?
Im on ww firmware.. ty
SIM not recognized
This is awesome, great, thank you very much for providing this.
However my SIM is not recognized. Both slots appear as empty.
Is there something I can do? I have no experience in these things.
Bricked
bohemist said:
Update: I've tried it but it does not detect SIM. I don't know why, it just says "Empty Slot" on either SIM 1 or 2.
EDIT: I think it's IMEI issue, which I've read very common to Asus phones.
Click to expand...
Click to collapse
Hi Bohemist,
Just wondering if you have the stock rom for this device. I bricked my unit and hanged at ASUS logo. Is there a way you could help me, please. Maraming Salamat! Am from San Pedro Laguna din.
Thanks!
AlianE01 said:
Hi Bohemist,
Just wondering if you have the stock rom for this device. I bricked my unit and hanged at ASUS logo. Is there a way you could help me, please. Maraming Salamat! Am from San Pedro Laguna din.
Thanks!
Click to expand...
Click to collapse
Unfortunately, wala. I already sold the phone
You can find stock rom at asus website. I will check if I still have it bookmarked .
Is this ROM compatible with MT6737T chipset?
freddy mawrie said:
Hello everyone, ive been working on a custom rom, and i like to share with you guys this rom which i have ported ( Lineage 14.1 for our dearly asus zenfone 3 max) which is currently not that stable yet but it has good battery backup , good for daily driver. i will post a patch for fixing bugs soon...
NOTE: This rom is for asus ZC520TL, having MT6737M chipset only.:fingers-crossed:
Things you need:
*Rooted and TWRP install link:
*Latest stock android 7.0 with lastest security patch (July 5, 2018).
* Lineage_14.1_Unofficial link: https://drive.google.com/open?id=1bZ_z_lzfHfmCbjxjEloXEDOU9ZEU2fln
Features:
All Lineage OS features
what is working:
1. RIL (call,data,sms) except volte
2. Dual sim
3. Dual sim 4G
4. WIFI
5. Hotspot
6. 4G/2G/3G switch
7. F.M radio
8. VPN
9. Youtube
10. All storage mount and also OTG
11. Audio
12. Offline charging and many more
NOT WORKING:
1. Bluetooth
2. Finger print
3. camera
INSTALLING PROCEDURE (TWRP):
1. Take a full Nan-droid backup first
2. Open WIPE/Advanced/ and format system, cache & data first.
3. Now install the Rom.
4. Install Gapps. (pico recommeded but its your choice).
5. Wipe Dalvik/ART cache
6. Reboot
Now it will take 10-15 mins to boot-up
No network after installation completed?
-> go to setting /Simcard /sim1 or sim2 setting and change to your desired network.
No navigation button?
-> go to settings/Button...
Click to expand...
Click to collapse
Masih ada yang punya filenya ? Link di atas sudah dihapus, terima kasih
Mod translation: Does anyone still have the file? The link above has been removed, thank you
Used a number of different methods from various sources, most of them on this forum.
Each time a successfully got root on the phone i don't have Wi-Fi ("No Wi-Fi networks available").
I have used the latest twrp for G4, Elemental-G4-3.01 with Magisk-v19.1, SR5-SuperSU-v2.82 and superuser etc.
My latest attempt was following instruction in this thread:
https://forum.xda-developers.com/moto-g4/how-to/guide-how-to-root-moto-g4-magisk-stock-t3725712
When I fail I go back to ATHENE_NPJ25.93 and Wi-Fi works perfect each time.
What should I do?
staffanbe said:
Used a number of different methods from various sources, most of them on this forum.
Each time a successfully got root on the phone i don't have Wi-Fi ("No Wi-Fi networks available").
I have used the latest twrp for G4, Elemental-G4-3.01 with Magisk-v19.1, SR5-SuperSU-v2.82 and superuser etc.
My latest attempt was following instruction in this thread:
https://forum.xda-developers.com/moto-g4/how-to/guide-how-to-root-moto-g4-magisk-stock-t3725712
When I fail I go back to ATHENE_NPJ25.93 and Wi-Fi works perfect each time.
What should I do?
Click to expand...
Click to collapse
Check this https://forum.xda-developers.com/moto-g4-plus/how-to/guide-g4-baseband-network-volte-issue-t3865608
xDante2017 said:
Check this https://forum.xda-developers.com/moto-g4-plus/how-to/guide-g4-baseband-network-volte-issue-t3865608
Click to expand...
Click to collapse
Thanks!
I am new to rooting phones so excuse my ignorance.
I am going to connect this phone to a car navigation/entertainment system using USB and via Android Auto (with some patches) "mirror" the phone screen to the car screen.
I don't need to do any calling using this phone, only need wifi.
The post you refer to seems to be related to baseband problems, is it the same kind of problems?
However in the first part of the post it mentions IMEI = 0, which is the case for me, should I go down this route and try to solve this issue (if possible)?
The thing I don't understand is that wifi works fine (with IMEI=0) when flashed to stock but as soon as it's rooted it looses wifi and bluetooth (and possibly other stuff)
I'm having the same issue and as this thread is still fresh I figured I would post here, I tried the flash posted above but all it did was trick my g4 into thinking its a g4 plus with no wifi still, I understand that is what its suppose to do and a fix is there for it but right now I'm trying to fix wifi.