Hello,
I've been using an android radio bought at aliexpress:
https://a.aliexpress.com/_uvy5FM
From time to time its performance would decrease and eventually the device would get stuck in a boot loop. I then contacted the seller who sent me the firmware. After flashing the device, everything went back to normal. A few days ago I had to flash the radio again but this time, after starting the update, the device would just restart with update interrupted. I now cannot enter recovery mode and the device keeps rebooting. What can I do to fix that?
All I can say for now is that it runs Android 10, has 64GB of storage and 4GB of RAM. It is powered by an rk3368. The firmware is probably a customized PX5 - rk3368-userdebug 10 QP1A. 190711. 019 101626...
Please help. If any further details are needed, I will try to provide them as my access to device info is limited due to the bootloop... I still have the firmware archive.
Thanks!
Related
I have a problem after the update via OTA, the phone will restart and stayed on the logo Samsung Galaxy Core 2 GT-355HN.Nakon return phone software again restarts and does not respond to touch when you boot the system stand for 1 minute and again restarts sam. I worked in the Recovery and wipe cache, and again restarting and does not respond to touch. I installed several software for Southeast Europe because it says Recovery SEE.I writes that HEAD INFO DONT UPDATE'FAIL, everything else is good,what to do?
(Moved from general discussion)
Hey all,
I've run into a bit of a pickle..
I replaced the screen on my S8 (SM-G950U) and after booting, it immediately gives 'System UI isn't responding' and/or 'Process system isn't responding'.
Shortly after (1-3 minutes) the phone will reboot. The errors may appear 1-2 more times before rebooting.
A bit of info:
Model: SM-G950U
OS: G950USQU4CRE9
Steps taken:
Clearing cache does nothing.
Factory reset via recovery mode has no change.
Flashing stock ROM (same version) with ODIN does nothing either.
Before restoring I was able to go in and see the RAM was reporting what I assume is normal (~30% usage)
Also the front camera was no longer working, but I've replaced that as well and haven't had the phone on for long enough to get through the initial setup to test.
Anyone have a potential solution / suggestion? Any and all help is appreciated. Thanks!
Edit:
It might also be worth noting that the shutdowns only happen after booting. There's no issue when entering recovery / download mode.
Havr you tried safe mode?
I know this is an old thread but hoping to get some guidance. I am facing the exact same issue on my at&t s8+ snapdragon as mentioned above. The device is unrooted and was with stock oreo rom. suddenly started showing either "system iu isn't responding" or "process system isn't responding". Later the device started hanging and kept restarting. It restarts from samsung logo instead of the device model name unless force restarted. This cycle keeps happening. I am able to access download mode and recovery without any problem. recovery initially shows "installing update" followed by "no command" but then works normally. The device doesn't power off even from recovery, it keeps rebooting. I have tried (1) cache wipe (2) factory reset from recovery (3) safe mode (4) installed stock rom without problem (5) installed latest stock s8+ unlocked xas pie rom without problem (6) installed latest stock s8+ sprint version pie rom without problem but i am unable to even end the initial device setup as the device keeps hanging with these errors and restarts. Any ideas would be appreciated.
Hi
I am stuck with Pulsing blue LED and the "Powered by Android" screen,
have access to both the recovery and the download Mode,
I also have Odin (version 3.13) on my computer along with TWRP (3.1.1 trlte and 3.2.1 version)
My device is a Samsung Galaxy Note 4 N910F bought in shop, no special carrier. It was bought in the Netherlands.
I have tried everything that I have read. The furthest that I can go is the Second Samsung Logo with the Flashing Light
Whenever I try to Flash the stock Firmware for my N910F, everything goes well in Odin but then when the phone reboots, it (sometimes) install the system update until 30% then shows erasing then either crashes right there and then or load the system update bar, completes it then shuts down.
I have tried multiple firmwares, even recovery firmwares. All the same problem. I can see the firmware is flashed, because when I enter recovery mode after I flashed a different ROM, it shows the version I flashed.
I cannot seem to install TWRP because it was never rooted.
Whatever I do, at some point, my phone either gets stuck in a bootloop, freezes with the LED light or shuts down.
And I have also proceeded to use different batteries.
Do you have any options?
Thank you
Heat????
I'm far from an expert here, but I've just experienced a similar problem where my N910F started boot looping / freezing within 15s to 2 min after unlocking. Unfortunately my micro Sd (SanDisk 256GB) was corrupted a week ago, so before doing anything else I did some research (XDA/YouTube) and probably found pretty much what you've found. I frequently change batteries so I could discount that as an issue. Someone suggested using the Samsung Smart switch here https://www.samsung.com/uk/getting-started/smart-switch/, but I haven't used it (yet) so I can't tell. I presume you had the latest firmware from Sams https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/.
My issue was that I needed to recover data, docs, photos, phone numbers etc. When boot looping the note 4 got very hot . In particular around and to the left of the camera (looking at the rear). Thinking it could possibly be the dreaded eMMC problem which also manifests itself by creating heat, I thought cooling the device might help. I placed the Note on a cooler box freezing block and voilà! No boot loop. I was able to remove all, but necessary apps and do a full copy to my PC. Storage was reduced from around 90% to 50% and memory 80% to 60%. It's now been stable for 12 hours, but the jury is still out. Next will be full reset with he latest available firmware 6.0.1 as mine was still on 5.1.1.
Good luck and hope this may be of some help.
I've got this problem, too, when using the unofficial Lineage 15.1 rom. SIM death and boot loop. After flashing the latest stock rom through odin, it passed but the screen was black and no system was installed. The blue notification light was constantly stuttering, though. And I couldn't even go to recovery!
When flashing, a 910F can get hot - use a cool temperature room and/or a fan blowing onto the device.
If it's not too late...
Hey!
My head unit is stuck in bootloop. It's an xtrons Android 10 PX6 unit MTCE_GS_V3.67_3 (Nov 7 2020).
I tried to flash Hal9k with the modinstaller downgrading to Android 9. Got stuck in bootloop.
That can happen. So I went back to Android 10 again and installed CHS2_RK3399_10.0(20200424)img via SD - stuck in bootloop.
I have access to recovery though and tried wipe cache and factory reset.
I tried to find help in old threads, pressed with 5 fingers on the screen during boot-up, and tried tapping on the screen.
The unit is connected to a DC power supply on my desk and I always disconnected power between all tries. No success.
Any more ideas?
Thanks for your support! It's well appreciated!
I have a similar issue with Ownice C800 PX6 rockchip 3399, i changed an option on the setting to have it default to off instead of On, after it rebooted nothing shows up on the screen. i can access the recovery menu and did a factory rest and nothing happens, i installed
Malaysk ROM for PX6 RK3399 with Android 10 and the update was successful but still no boot at all, the recovery log shows failure to create file in memory. not sure if the setting made the memory protected and why the boot is failing.
My apologies previous threaders I cannot fix your bootloop, but have similar problem.
Question to bluefreak, how did you get into recovery mode?? from a bootloop??
My original item is a 4gb ram 64 gb rom, px6 unit, previously I put a russian rom flashed via update to system on it, I think I paid 20 usd for it and it worked a treat until my son used the car, several years past warranty. And it has gone into bootloop.
I think the flashed rom was Malaysk?? I may be wrong.
I have a reset button, held it in for a minute still bootloop, connected another rom via usb and it will not flash, just bootloop. I have also attempted many methods from google and youtube.
Good Day XDA.
Guys i have a problem and need some advise and help, i downloaded what was to be the latest system update to fix the Radio app no sound since i bought the unit.
flashed the System update all went okay - Android rebooted and completed its setup and was prompted to restart for the settings to take affect.
and boots up into a black screen no boot logo nothing.
i plugged in a USB keyboard and can snap photos so the unit is on and working i assume the System update messed up the Graphics display.
is there anyway to get this T3L into recovery mode to Flash the Original System update again to fix this problem?
please anyone with any ideas or tips and tricks i would be very grateful.
Thank you guys