Database Users

Today is the worst day of my life

I woke up this morning to find my 8525 sitting in my computer chair as usual. Only to reach over and grab it, and ....its sitting in three inches of water. I have no idea what happened, or how it got there. All i know is my phone wont turn on, and is totally dead. Is there ANYTHING that can be done to right this horrid tragedy? Any help would be a gift from god. Thanks

Wow.
Sorry about that.
Let it dry out before trying to use it. Since it's wet, you have nothing to lose by taking it apart to facilitate this. You could dry it faster by using a hair dryer but NOT on the heated setting.

agreed; but let it dry for a day or two before you try, you should also put it somewhere that will provide additional moisture evaporation (gas oven with pilot lights or a furnace room, behind a PC fan or the like). i saved my old Sony S710a by letting it bake in my hot car for about 6 hours while i was at work. just make sure its totally dry before you try, and considering you already voided the warranty with the pool of water incident, you might as well take it apart if you can to make sure its completely dry.

hmm, bad luck.
Try all the above suggestions. But make sure you have disconnected your battery

Tried putting the battery back in after about a good 4-5 hours of being in the sun. All i get is a crackling noise when i try to place the battery to the metal conductors

Ewww.. I know it is stressful for you not to switch on the phone, but doing that will just make matter worst. Since you said that it wont turn on, I presume that you've tried it once (Strike 1), and you did it again 4-5 hours later (Strike 2), which usually others just leave it for at least 1 day (but probably the sun does help).
Can you identify what water is it? Can there be mineral within? Which may cause a short circuit somewhere in the phone. You'll need to open up the phone and clean it up somehow.. either DIY or get some phone shop people to do it. Your warranty is 'washed' anyway.

Try This
Stop Drinking!

Read This To Possible Save You Phone
OK, this comes from my many decades in the electronics industry.
1. PULL the battery. Do not put it back in in few hours.
2. Where did the water come from? Was it really water or? You need to know this. It's real important because mostlikly the PCB is contaminated. Anything that got inside has most likely contaminated the board and will cause shorts, intermitent contacts and the like. Even rain or spring water, it's the minerals...
What you have to do most likely is disassemble the unit. Get a gallon of DISTILLED (not Spring) water. Distilled, also know as deionized is free of all minerals. You are going to have to carefully submerge the board without the LCD in the water and gently rub it with a very soft tooth brush while underwater. Next take it out and put in another bath of distilled water. Agitate it gently. This proces should remove any contamination as long as the offending liquid is not sticky or heavily acidic or base. In the case of the later 2, you are most likely screwed.
Ok, so now you have a wet board. Genly shake the excess water off of it. Turn your oven onto WARM. Nothing above 150 F. Let it warm up and then shut the oven off. Put the PCB in the middle of the oven directly on the rack, close the door and come back 8 to 10 hours later. If the board isn't dry, repeat the steps again.
If you are luck and didn't fry it from trying to power it up, it may work again.
I have saved lots of radio equipment from rain & saltwater submergence this way.
Feel free to PM me if you need to. Good Luck.

I used to have a motorola and dropped it into a bucket of water. Dried out in a few days and it was working fine.

my 8525 recently fell in the sink. as soon as i seen it in the sink i pulled the battery out. rigged the phone up on something in the floor so air could ventilate under and over, set the hair dryer on high (but without the heat) and 5 or so ventilation fans from a desktop pc wired to a 9v battery. let the hair dryer go for about 15 minutes but left the fans on over night. took the phone with me to school the next day and left it in the car during both of my classes. came out put the battery in and powered it up. works just fine now

http://www.wikihow.com/Save-a-Wet-Cell-Phone
ive heard the rice thing works, ive alway wanted to flush with alcohol, that would in theory dilute the water and the alcohol would dry out faster.

Ok so heres the deal. I put the battery in. Power up the phone, gets to the vp3g startup screen, then fades to white. Could someone point me in the direction of a tutorial that shows me how to disassemble a Hermes CORRECTLY.
Hopefully ill be able to give it a DI Water bath and breath a little life back into her. Thanks for all the help guys, I really appreciate it

It's drying out slowly. I had a Hermes that did the same thing - eventually getting to the "screen behavior" you describe. I never fully disassembled it. I just let it sit open, with the battery out, keyboard pulled out, and the back off. Eventually (after leaving overnight), it was fine. Worked normal ever since that with one exception.. I had forgotten to pull the SD card. The SD socket never worked again :-(
Moral of the story: don't forget to take out the SD card.

todd_jg said:
It's drying out slowly. I had a Hermes that did the same thing - eventually getting to the "screen behavior" you describe. I never fully disassembled it. I just let it sit open, with the battery out, keyboard pulled out, and the back off. Eventually (after leaving overnight), it was fine. Worked normal ever since that with one exception.. I had forgotten to pull the SD card. The SD socket never worked again :-(
Moral of the story: don't forget to take out the SD card.
Click to expand...
Click to collapse
yeah i got lucky. when mine fell in the sink i had the SD card out and in the laptop doing hw. so i guess im really lucky that the sd socket still works

Not worried about the SD card as much... Anyway, Ive popped the back off of my 8525 after removing a couple screws. On the back of the circuit board there is white material that can be wiped off with a little rubbing alcohol and an ear swab. What is that crap? Ill go further in depth here soon once it fully drys. I sure hope I can get this thing running again, birthday is the 13th and would be a nice little gift to myself to get the phone working. Thanks for the help guys

WOW Just look it here...Thats what I call the Power of Unity man. Great piece of work, info. I love all You people. If the world learns anything from XDA developers then there wont be any more human sufferings I am sure..Enjoy friends the power of forum..

If it fades to white, it is still wet.
You need to let it dry a lot longer before trying to use it.

Sterch said:
On the back of the circuit board there is white material that can be wiped off with a little rubbing alcohol and an ear swab. What is that crap?
Click to expand...
Click to collapse
Well, those are either stuff from the water or stuff from your phone that is washed and gathered to form some dangerous circuits (much like coffee water rings, that things tend to get to the edge of waters). These stuff may conduct electricity, hence making your phone goes nuts. Search and destroy all these 'crap' Good luck. Don't try the phone unnecessarily until you are sure that all 'crap's are gone. One of these 'crap' may potentially kill your phone (ok, it is usually not that serious, but just incase )

Sad story, I was lucky with similar story, but much cheaper. I left my Nokia BH-600 Blue Tooth Head set in my panties and give them to washing-mashine. 40 degrees program for 30 minutes ended by wringing on 800 turns/minute
When I found it in the pocket I just left it to wither up and it didn’t worked. So I tried to re-charge it and WOW it works and the battery has normal capacity.

Video of 8525 / Hermes being dismantled
Sterch said:
...Could someone point me in the direction of a tutorial that shows me how to disassemble a Hermes CORRECTLY ...
Click to expand...
Click to collapse
Don't forget the popcorn: http://www.youtube.com/watch?v=zsljpn74SW0

Just dropped my HD2 down the toilet

I immediately removed it from the water, and desperately tried to remove the back case to remove the battery (its quite hard when the phone is wet) i got there eventually though.
The screen was flickering whilst the phone was still on, and the water sensitive stickers on the battery and phone are both pink. I've blow dried it for about 10 minutes haven't tried to start it back up yet.... any suggestions?

joeyjoee said:
I immediately removed it from the water, and desperately tried to remove the back case to remove the battery (its quite hard when the phone is wet) i got there eventually though.
The screen was flickering whilst the phone was still on, and the water sensitive stickers on the battery and phone are both pink. I've blow dried it for about 10 minutes haven't tried to start it back up yet.... any suggestions?
Click to expand...
Click to collapse
DON'T start it for a few days. Put it in a warm place, leave it to dry for 48-72 hours and pray it works when you turn it on.

yeah just be patient and wait about 3-4 days to dry. but do not put it under direct sunlight

....and wash your hands

Try to put into bag with rice, and leave for couple of days...

DanijasDub said:
Try to put into bag with rice, and leave for couple of days...
Click to expand...
Click to collapse
put it in a bag of rice or leave out in the open?!?

put your phone into rice and keep bag closed

Basically you just need to make sure you dry it out thoroughly. Don't try to rush this process in a few hours. All the posts about leaving it somewhere warm (like an airing cupboard) are correct. Don't put it on top of a radiator or hot pipe, or in the sun as already suggested. The idea of putting it in a bag of rice is to help draw the moisture out. Never tried this method myself.... You really must be patient with this - managed to save my Touch Pro that got soaked in the rain last year....

okay so i've put the phone the battery and the sim on top of some rice in a bad behind my tv in my bedroom

rice like the others said or if you are a cigar person (or know someone who is) place it in an acrylic humidor w/ humidification beans.......I resurrected a M$ ZUNE my wife dropped in a rain puddle by doing this in my humidor

man, this reminds me of the time I dropped my phone in a bucket of puke from a heavy night. Still worked after I dried and cleaned it up.

"DON'T start it for a few days."
yup ..is correct wait until dry ... "rice" are good for absorb humilities ..
but If I not wrong ..after dry .the speaker of the phone will change ..just like my tytn II drop into "wash floor water", it still can use .. but the speaker sound change ...

Οh man , really bad luck..
hope it goes ok but be patient and let it dry manually !!!

my wife washed my cellphone once (left in pocket after heavy night of drinking). Took the battery out, let it sit on a counter for about a week. Phone recovered though it took the screen a while for the colors to all show properly.
I have read where people put their oven on warm and leave it overnight. I don't think this will hurt the phone since their won't be a power source in it.

Dropped in a sink with the tap running!
I dried it out under a hand dryer, then powered it up straight away. In hindsight this was pretty stupid, but it booted up ok. The only problem being the NAVPANEL would randomly appear and require a reboot. The next day that problem had gone away, and was replaced with a new problem - the Volume down button being jammed on! Also the battery life was reduced to about 10 hours. After a further 48 hours and a blast with compressed air (around the volume buttons) the phone has returned to 100% normal use - even the battery life is getting better, now upto about 36-42 hrs..... but I have bought a replacement for that anyway!!
Can't believe how lucky I was!

[Edit: Just saw you fixed it. Bravo! I'll leave this here anyway...]
Rice is good, unless you have any silica gel kicking about, the stuff you get in electronic packaging in the little paper bags/sachets that say "do not eat".
But yes, definately don't do what the majority do...
"I just turned it on to see if it would work..."
"You turned your phone/laptop on while it was wet... to see if it would work?"
"Yeah... why?"
*facepalm*
Happens about once a week in the PC store I work at. You could also try stripping it after it's dried and going over it with a carbon pen to remove any corrosion/residue.

After removing the battery, SIM, and MicroSD and gently removing any surface water.
One trick I found is to put a phone in the path of hot dry air for 30 minutes to a couple of hours. A clothes dryer vent works wonderfully for this since its temperature controlled (and timed) to keep from destroying the fabric in your clothes, and hot enough to allow water to evaporate. If you have access to your dryer vent hose, unhook it and rest it on top of the dryer and put your phone in the path (at least 4 to 6" from the opening). It's worked for 2 phones so far. One being my wife's Motorola, and one my Touchpro. If you have a dryer with an insert for shoes, you could use that as well, although I would put the phone on something to keep it from vibrating off.
You could use a hair dryer but keep in mind that hair dryers are not designed to be run continuously and the temperature is not technically regulated.
The trick is to get the temperature of the whole phone up to about 130 to 140 degrees and the water will evaporate. I would avoid shaking the water out of the phone or using pressureized air since that will push water into the delicate connectors, keypad matrix, screen, etc.

Let me give you a more scientific approach to your problem, i will try to explain as better as i can since english aint my primary language.
After you drop it in the water, your phone will never be the same for couple of reasons. First of all, when the water will dry, salt will "sit" on the connections and the weldings of the connectors, and that will slowly but steadily eat them. My saying is : " Never trust a phone that was dropped into water/coffee ". For you to be sure of your phone you need to strip it, and clean it with a spray for electrical appliances. Now there are 2 types of those sprays, one with oil and one with no oil in it. For your thing you need the NO-OIL one. Thats to make sure you wont get a loose joint and eventually your phone wont get broken.
If you dont feel like opening your phone and you dont feel comfortable with it, just ignore my post and just dry it out. What is 100% sure is that at some point it will break down, it depends on when though, from hardware to hardware.
Just my 2 cents.

Any time I get anything wet I IMMEDIATELY remove the battery, then I remove anything else I can from it: Sim Card, Memory Cards, etc. I don't like the rice idea because rice ALWAYS ends up stuck somewhere inside. I prefer setting my phone on some foil out in the sun for a bit (provided it's not too hot out) or just leaving it somewhere where it's warm to dry out. DO NOT BY ANY MEANS put the battery back in or turn it on until it is COMPLETELY dry. A minimum of a day if you even want to begin to chance it. If it was dropped in something other than relatively clean fresh water, I would keep everything out of it (battery, sim, memory cards, etc.) and dip it in a cup of distilled water a few times to clean any particles off, then let it dry again completely before turning it on. Just because an electronic gets wet, doesn't mean it won't work. The only way to kill it really is if you power it back on or the battery shorts it.
I went swimming at the lake with my old Nokia 5310 for 10 minutes before remembering it was in my pocket, I immediately took everything out when I remembered and left it in the sun for 8 hours and it worked fine for a year after until I threw it into a wall as hard as I could due to a frustrating girlfriend haha

U may have problems in the future... Since it was submerged in water some components will begin to rust... I suggest u take it to a mobile service shop so they can tell u what to do, or maybe they can fix it...

[Q] Waterproof Epic!!

<---- Idiot jus dropped his epic in sum water & of course it's not working!! I dried it out w/ a towel & blow dryer after it happened. When I connect the battery the keyboard keys still lights up, but when I press the power button all I hear is a ringing type noise (sounds like a fan spinning) and no bootup. I cannot boot into CWM or Download mode either. Has anyone experienced this or found a solution w/o having to replace the whole phone.
** Also, my battery has the red marking on the top of it stating it's been wet.
EDIT: If I plug in my usb the LED light comes on, but it's blue & my phone was @ 80% when I dropped it.
Thanks in advance!!
UPDATE: [ I couldn't wait the 48 hours!! (36 Hours) -- LoL ] I just removed my phone/battery from the rice bags & everything is working!! Yes, even the battery is good @ 72%!! I can't believe it worked!! Thanks Matrix!! And thanks to everyone for your great suggestions!! This phone is truely EPIC!!

Turn it off and remove the battery now!!! Do not put the battery back in.
You're going to mess it up by turning it on when things are shorting out!
Take the battery and the phone. Put them (separately) in a zip lock bag full of rice. Wait a day or two. Then try it out.
PS: Everyone should ingrain themselves in this reflex: If your phone hits water, remove the battery NOW. Do the rice trick, and try it later. Resist the urge to see if it still works.

Thanks for your quick replay & suggestion matrix!!
I am currently trying your method, but I'm hoping I didn't further short anything on the circuit board by trying to get it to work earlier.. It sounds like a good plan because the rice will absorb the water and probably be ready for consumption in a day or two!! LoL

Forget the bag of rice, you need to take the phone apart immediately, to the last screw and board and wipe down everything with alcohol and blow it out and dry it with a hair dryer. Otherwise even if you get it to work in a couple of days, corrosion will start to build up on the contacts of various things inside and you'll end up having to get another phone.

And this is why that extra $7.00 a month is worth it.

hdnet1 said:
Otherwise even if you get it to work in a couple of days, corrosion will start to build up on the contacts of various things inside and you'll end up having to get another phone.
Click to expand...
Click to collapse
Forget about taking it apart... you're garonteed t miss somthing and the corrosion will kill it anyways. I know for a fact
Sent from my SPH-D700 using XDA App

hdnet1 said:
Forget the bag of rice, you need to take the phone apart immediately, to the last screw and board and wipe down everything with alcohol and blow it out and dry it with a hair dryer. Otherwise even if you get it to work in a couple of days, corrosion will start to build up on the contacts of various things inside and you'll end up having to get another phone.
Click to expand...
Click to collapse
Soo .. which 1 should I do?? They both sound right to me!! I checked on YouTube & I seen a vid about using the rice technique, but no vid about completely taking it apart to dry off the components??
styckx said:
And this is why that extra $7.00 a month is worth it.
Click to expand...
Click to collapse
I do have the warranty -- Doesn't water damage void it?? They can tell by the red marking on the battery.

No, just means you gotta pay them whatever the current fee is for water damaged phones. Used to be 50 bucks, but I think the crooks doubled it. As for taking it apart, forget about that nonsense. Bag of rice for a couple days, take it out, if it boots up you are fine.

muyoso said:
No, just means you gotta pay them whatever the current fee is for water damaged phones. Used to be 50 bucks, but I think the crooks doubled it. As for taking it apart, forget about that nonsense. Bag of rice for a couple days, take it out, if it boots up you are fine.
Click to expand...
Click to collapse
Cool .. I really didn't wanna take it apart. I would have prob did more damage to it!! LoL I will wait out the 2 days & post back w/ an update then.
Thank you all for your help!!

CRC Mass Air Sensor Cleaner
You can find it at auto parts stores, its an electrical component cleaner that displaces water, removes grime, grease, corrosion and dries with no residue.
You have to take it apart to use it and don't get it on plastic stuff. CRC makes several different electrical component cleaners and some of them will eat plastic so be careful with it.
Saved my Sprint Hero with this stuff after it landed in a puddle and spent about two minutes fully submerged in the water before I found where it landed. Luckily I was home, ran inside, took it apart and grabbed a can of CRC I had in the garage on a whim.
Granted, I never tried turning it back on while it was still wet, that is often the killer for wet electronics.
Just figure that its dead, whatever you do to it at this point isn't going to hurt it anymore but I would HIGHLY recommend taking it apart to make sure you get all the moisture out of it. I don't put much faith in the rice trick

D`Nyed said:
CRC Mass Air Sensor Cleaner
You can find it at auto parts stores, its an electrical component cleaner that displaces water, removes grime, grease, corrosion and dries with no residue.
You have to take it apart to use it and don't get it on plastic stuff. CRC makes several different electrical component cleaners and some of them will eat plastic so be careful with it.
Saved my Sprint Hero with this stuff after it landed in a puddle and spent about two minutes fully submerged in the water before I found where it landed. Luckily I was home, ran inside, took it apart and grabbed a can of CRC I had in the garage on a whim.
Granted, I never tried turning it back on while it was still wet, that is often the killer for wet electronics.
Just figure that its dead, whatever you do to it at this point isn't going to hurt it anymore but I would HIGHLY recommend taking it apart to make sure you get all the moisture out of it. I don't put much faith in the rice trick
Click to expand...
Click to collapse
True, it prob is near dead at this point. I will try this solution if the rice trick doesn't work tomorrow. Hopefully, one of these solutions work out!! Thanks for your input!!

It's def dead if u already tried to turn it on.
Just tell them you dropped it off the side of a boat.......then you wont have to show it to them

My buddy dropped his epic4g in the toilet bowl, he was paying insurance ($7.99 a month.) He did the samethings you did and did the rice trick and nope didn't work. Ended up calling sprint and spending 150 I think for a replacement phone.
- Its just going to be Epic!

Silica Gel packs are better than rice if you have any of those.

BUMP!! Please read my update to my OP!! Rice is the not only good for eating!! LoL

Water Damage

So I dropped my N1 in water. Took out the battery as soon as possible then I dried what I could with a towel.
After this I tried hours of the rice method (putting my N1 in a bag of dry rice to dry it out). And I was able to successfully boot up my phone again, almost everything works fine but the digitizer/touch screen has some issues.
The rightest side of the screen, about an inch worth is completely unresponsive, so if I load up my app drawer and try to click anything on the right it won't work at all just so you know what I mean.
What can I do about this? Is this a simple fix? Do I just need a new digitizer? Or is it something else?

Water damage can affect anything. Luckily the digitizer is only $25 and there are tons of videos on how to disassemble the phone.

Sounds to me like you've still got a short somewhere inside your N1. Here are some suggestions.
1. Rice is a desiccant, it takes a LONG TIME to actually dry-out something like the internals of a phone. If you can part with the phone for that long, I'd suggest leaving it in the rice for more like 72hours!!
2. If you can't give it that much time, and you've got some tools, skills and a willingness to take apart your N1? Then search youtube for "nexus one disassembly" and take it apart, being extra sure to manually dab dry all areas possible (especially in the digitizer area as you've stated issues around there).
3. Finally, if those steps don't work, you're looking at a digitizer replacement. Which, if you've already taken apart your N1 from step #2, will be an easier swap out for you to handle.
My N1 too went for an unwanted splash as well. Total submersion for a good few seconds as I had to fish it out. Water had gotten into the screen, EVERYTHING was wet.
I had the tools and the mindset that my N1 was likely dead anyway so taking it apart couldn't hurt any further. So I took it completely apart, used a paper towel to dab dry everything possible that I could. Then I left everything out on the table overnight to dry.
Next morning I put it all back together and to my delighted surprise everything worked!
Our N1s are troopers! I'm confident you can bring yours back to full life!
Good luck!

Thanks for the responses!
I will definitely try taking it apart and I'll post back soon on the outcome, if I get lazy though I'll just buy a new digitizer.

How is it possible that water doesn't hurt your N1? It's completely incredible. Few years ago i had a samsung player (my son in fact) that was in contact with water (no immersion!!) and after drying for a week (air then hair-drier!) it was impossible to get it on again.
Is N1 that strong!! So lucky you are!!

abccg said:
Thanks for the responses!
I will definitely try taking it apart and I'll post back soon on the outcome, if I get lazy though I'll just buy a new digitizer.
Click to expand...
Click to collapse
Well if you buy a new digitizer you're gonna have to take it apart anyway haha.
Sent from my Nexus One using Tapatalk

abccg said:
So I dropped my N1 in water. Took out the battery as soon as possible then I dried what I could with a towel.
After this I tried hours of the rice method (putting my N1 in a bag of dry rice to dry it out). And I was able to successfully boot up my phone again, almost everything works fine but the digitizer/touch screen has some issues.
The rightest side of the screen, about an inch worth is completely unresponsive, so if I load up my app drawer and try to click anything on the right it won't work at all just so you know what I mean.
What can I do about this? Is this a simple fix? Do I just need a new digitizer? Or is it something else?
Click to expand...
Click to collapse
Use rice is a real bad idea, hairdryer is the best and i'm pretty sure you can find one in your house or borrow one from your neighbour
Seems like there is still a short in your cellphone and i would recommend you call your manufacturer for this. Anyway, it's risky to repair a cellphone by yourself.

A little over a year ago I washed my Nexus One in the washing machine. Extra bleach, long cycle with an extra rinse cycle since it was a bunch of dirty clothing.
I remembered it was in my pocked when I went to remove my clothing, I was sure it was dead.
I pulled the battery and put the phone on the dry air vent of my dehumidifier for two days. The vent blew warm, completely dry air directly into the open back of my phone.
I popped the battery back in and it's been working like new ever since. The camera colors are ever so slightly off, however.
Let the phone dry out before you try to turn it back on.

Recently had the same issue. In my case was a bit easier.
What I did - removed back cover, battery, SIM, sd-card..
Switched my laptop and loaded it with compiling linux kernel. Then decoding HD video with handbrake. The aim was to get a constant flow of warm air (abt 70 degrees Celcius). And I put my phone close to vent fan out of my laptop. It is not overheating too much (like you can with air dryer).

I had a water damage as well, sliped with phone into the while geocaching. The salt walter wasn't good for my phone... :-(

CCpotter said:
Use rice is a real bad idea, hairdryer is the best and i'm pretty sure you can find one in your house or borrow one from your neighbour
Seems like there is still a short in your cellphone and i would recommend you call your manufacturer for this. Anyway, it's risky to repair a cellphone by yourself.
Click to expand...
Click to collapse
I always thought rice, particularly instant rice because it is so absorbent, or any dessicant was a good strategy.
On the other hand, hair dryers seem a very bad idea. Heat from the dryer can be damaging, but the real damage from a hair dryer is that is sends the air at a strong velocity and it blows the water further in the device.

CCpotter said:
Use rice is a real bad idea, hairdryer is the best and i'm pretty sure you can find one in your house or borrow one from your neighbour
Click to expand...
Click to collapse
cyberstoic said:
I always thought rice, particularly instant rice because it is so absorbent, or any dessicant was a good strategy.
On the other hand, hair dryers seem a very bad idea. Heat from the dryer can be damaging, but the real damage from a hair dryer is that is sends the air at a strong velocity and it blows the water further in the device.
Click to expand...
Click to collapse
Rice is actually a very good thing to use just like cyberstoic says. It sucks the water into the rice and gets it out of the device.
The reason he listed for the hair dryer is valid, but it isn't the main reason. The main reason is that the hair dryer will just cause the water to evaporate, but that doesn't necessarily mean that the super humid air will leave the device, so as soon as it cools back down, you will still have that moisture in there.\
This is why rice or other desiccants (like all those silica gel packets that come with a lot of packaging) are used. They actually pull the moisture out of the device.

Rice worked for me when my N1 spent a night soaking in seltzer. (not completely submerged, but enough to get a big batch under the screen) But first I used a vacuum to suck out as much of the seltzer as I could. Then I put it in rice for about 30 hours.
Sent from my Atrix 2 using Tapatalk...

cyberstoic said:
I always thought rice, particularly instant rice because it is so absorbent, or any dessicant was a good strategy.
On the other hand, hair dryers seem a very bad idea. Heat from the dryer can be damaging, but the real damage from a hair dryer is that is sends the air at a strong velocity and it blows the water further in the device.
Click to expand...
Click to collapse
What about the dirt in the rice? If you use rice to dry those water inside, the dirt with rice will melt with the water inside and make damage to your elements.
If you use hair dryer in a proper way, it can dry your water inside without causing any damage. Have seen after-sale repair workers do this many times.

CCpotter said:
If you use hair dryer in a proper way, it can dry your water inside without causing any damage. Have seen after-sale repair workers do this many times.
Click to expand...
Click to collapse
Did you read my response at all? While it is possible for the hair dryer to fix the problem, it can also cause the problem to remanifest itself if that humid air doesn't actually leave the casing. That is the point of the rice. Dirt in the rice is irrelevant. We aren't talking about that much water, and the phone is still in its casing. The rice is just removing the moisture from the air.

Accidentally wet my lg v20

Okay so I was shaving with my phone on the sink, as I leaned in my phone fell in the running water . I took it out the water as fast as I could and took the battery out Just to make sure no water got in the phone . I put the battery back in and the screen is now flickering how long should I let it dry and how should I dry it any help would be gladly appreciated. ...........yeah I know I'm a big dummie lol plz don't flame me !

Put it in rice for 24 hr if not longer, your second mistake was to power it on after it getting wet.

I'd immediately put it in a bag of rice and let it sit for at least 24 hours personally.

easyguy said:
Put it in rice for 24 hr if not longer, your second mistake was to power it on after it getting wet.
Click to expand...
Click to collapse
So since I put the battery back in and turned the phone back on did I just mess this baby up ???

Good chance. Impatience is not your friend.

@rbiter said:
Good chance. Impatience is not your friend.
Click to expand...
Click to collapse
well I didn't actually put it back in a second time just that one time ! could I have finished this baby off or do I have a chance of resuscitating this baby ???

Rice rice baby, you know? Or silica packs. With the quickness.

ricosuave88 said:
So since I put the battery back in and turned the phone back on did I just mess this baby up ???
Click to expand...
Click to collapse
Dunk it in 99% alcohol for a bit then take it out & dry it off... Should be good to go.

http://smartphones.wonderhowto.com/...st-way-save-your-water-damaged-phone-0154799/
Silica is best, but cat litter, instant couscous, instant rice, and instant oatmeal all performed better than uncooked white rice—everyone's favorite damn drying agent.

Best you can do is place it in a bag of uncooked rice to try and draw the moisture out. Beings you already tried to powered it on then the damage might already been done. Leave in the bag for a few days but mostly its a lost cause as the connections will most likely rust over time as I seen happened with people in the past.
Sent from my LG-H910 using Tapatalk

You know what? I suggest popping open those 20 screws and air drying it. After 24h use something like Arctic clean 2 or alcohol to clean any contacts you can, including USB c port. You'll get to see more of your phone, display will probaly dry out better and you'll get an idea of components that may need replacing in future if it acts up.if you have it already or know somewhere close by, but some silica and put the disassembled parts in different Ziploc bags.